Filip Mulier
62db9848d3
Improvements and bug fixes in sensor delay buffer for filament sensor code
...
Improvement to avoid reinitializing delay buffer with every print. Fixed
issues in buffer indexing and memory out of bounds due to floating point
imprecision. Simplified the code by avoiding conversion to standard
diameter and 1cu mm extrusion, which caused complications in determining
mm extruded.
2014-08-16 06:50:13 -05:00
Florian Baumann
5908fd5cec
Fix reseting CHDK pin to LOW
...
chdkActive was set to false regardless of (millis() - chdkHigh) being bigger than the CHDK_DELAY or not. So if (millis() - chdkHigh) wasn't bigger than the delay the first time, the CHDK would never be set back to LOW.
Also, don't return from the function, as there might be other stuff to do, after the CHDK check.
2014-08-11 14:12:32 +02:00
Roxy-3DPrintBoard
0adbc79571
Fix Default Configuration so Auto Bed Leveling is off
...
This snapshot has the Auto Bed Leveling turned off because most Marlin
users do not have that feature.
2014-08-10 10:18:54 -05:00
Roxy-3DPrintBoard
0091865583
Z_PROBE_REPEATABILITY test
...
Z_PROBE_REPEATABILITY test for Auto Bed Leveling.
Implemented as M48 with extra user specified options.
Full support at
http://3dprintboard.com/showthread.php?2802-Auto_Bed_Leveling-Z-Probe-Repeatability-code
2014-08-09 15:37:23 -05:00
Filip Mulier
85649a4549
Real-time filament diameter measurement and control
...
This feature allows the printer to read the filament diameter
automatically and adjust the printer in real time. Added code to read
an analog voltage that represents a filament diameter measurement. This
measurement is delayed in a ring buffer to compensate for sensors that
are a distance away from the extruder. The measurement is used to
adjust the volumetric_multiplier for the extruder. Some additional g
codes (M404, M405, M406, M407) are used to set parameters and turn
on/off the control. g code M221 is updated. Pins for RAMPS1.4, RAMBO,
and Printrboard are identified for analog input. The configuration file
is updated with relevant user parameters.
2014-08-06 19:30:57 -05:00
Filip Mulier
1d0fe035f3
Change pinMode to SET_INPUT or SET_OUTPUT
...
Original code is using WRITE from fastio, but original used pinMode to
set pin direction and did not use the fastio SET_INPUT or SET_OUTPUT.
This caused an issue with the rotary encoder interface to boards based
on teensyduino, since for teensyduino pin numbers for fastio and the
usual Arduino IO are different.
2014-08-04 21:44:04 -05:00
Charles Bell
e7707aedbc
Commented out new #defines in Configuration.h.
2014-08-04 10:18:25 -04:00
Charles Bell
0a8dc0e96b
Added documentation to the README.md for the sled Z probe option. CAB
2014-08-04 10:07:43 -04:00
Charles Bell
d2fcb3ee56
CAB: Added code for Z-probe with Z endstop mounted on a sled.
2014-08-01 11:29:59 -04:00
daid
c13a831ea1
Merge pull request #1017 from foosel/fix/checksum_truncation_bug
...
Fix for a wrong checksum truncation for certain commands
2014-07-24 19:41:34 +02:00
Gina Häußge
2d22902d08
Fix for a wrong checksum truncation for certain commands
...
Positioning of string terminator to truncate checksum from the commands
M23, M28, M30, M32, M928 and M117 was off by one, causing the last
letter of the actual command to be truncated instead of just the
checksum.
In case of the SD commands this caused checksummed commands targeting
existing files to fail since the last letter of the filename was
truncated.
In case of M117 this caused the last given letter not to be displayed.
This patch fixes the off-by-one error and sets the null terminator
on the exact position of the * starting the checksum instead of the
character before that.
2014-07-24 12:04:02 +02:00
cocktailyogi
ad3b770c1a
updated examples
2014-07-20 13:55:13 +02:00
cocktailyogi
2f4a20257c
imported last Marlin changes
2014-07-20 13:49:26 +02:00
daid
aacff0d361
Merge pull request #948 from Dim3nsioneer/Marlin_v1
...
Implementation of FW extruder change retract
2014-07-18 16:10:15 +02:00
midopple
17aa67e4ea
If the option DISABLE_INACTIVE_EXTRUDER ist active the extruder switch to early to inactive because there are some moves in the buffer. So the planner wait 32 moves to disable the unused extruder.
2014-07-13 21:52:32 +02:00
Robert Quattlebaum
1fd9a7d476
Fix for FWRETRACT on DELTA printers.
...
Fixes #817
2014-07-09 09:24:26 -07:00
Grogyan
bcd039aa81
Update pins.h
2014-07-05 17:55:03 +12:00
Grogyan
82606354dd
Update temperature.cpp
...
Enables both SD card and MAX6675 to talk with each other
Fixes also issue #750
2014-07-05 17:17:17 +12:00
bonm014
32a6451ad8
Add leapfrog and dual Y/Z
...
I have added the pin set for the leapfrog and the support of dual Y and Z
2014-07-03 21:15:03 +02:00
bonm014
b5417be109
Update Configuration.h
...
Leapfrog added to the board list
2014-07-03 21:03:22 +02:00
bonm014
f244045245
Update pins.h
...
Leapfrog board added to the pin list
2014-07-03 21:01:41 +02:00
Pablo Clemente
2242a84218
Changed the declaration of the variable to Marlin_main.cpp to fix issue on commit #965
2014-07-01 16:45:03 +02:00
alexborro
43c298a7a9
Add "Thermal Runaway Protection" feature
...
This is a feature to protect your printer from burn up in flames if it
has a thermistor coming off place (this happened to a friend of mine
recently and motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature
than actual. The system will turn the heater on forever, burning up the
filament and anything
else around.
After the temperature reaches the target for the first time, this
feature will start measuring for how long the current temperature stays
below the target minus _HYSTERESIS (set_temperature -
THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
If it stays longer than _PERIOD, it means the thermistor temperature
cannot catch up with the target, so something *may be* wrong. Then, to
be on the safe side, the system will he halt.
Bear in mind the count down will just start AFTER the first time the
thermistor temperature is over the target, so you will have no problem
if your extruder heater takes 2 minutes to hit the target on heating.
2014-06-30 15:22:49 -03:00
Pablo Clemente
d86c3cf43c
Changed the type of variable to bool, the name to "cancel_heatup", flags implementation and added this fix to M190 gcode too.
2014-06-30 15:12:13 +02:00
cocktailyogi
f0cab611db
optimised some math-code
2014-06-24 18:43:36 +02:00
Oskar Linde
269a068032
Fix lcd itostr3() to handle negative numbers
2014-06-24 14:31:15 +02:00
cocktailyogi
fae7d08698
fixed wrong compiler-option
2014-06-23 18:16:42 +02:00
cocktailyogi
512f2a3136
restore Branch from Backup
...
sorry for that
2014-06-23 17:09:57 +02:00
Pablo Clemente
cd3220d055
Inverted state logic for forced_heating_stop variable
2014-06-13 08:39:58 +02:00
Pablo Clemente
86b4b805d2
Fixed stop print LCD function on M104
2014-06-12 18:43:16 +02:00
Greg Tan
6e6e4e2143
Added thermistor table for the 500C thermistor shipped with the Pico hot end.
2014-06-08 09:35:04 +08:00
Gina Häußge
0de826160e
M30 response is missing linefeed, "ok" therefore not on own line
...
This leads to the command not being acknowledged properly
by the firmware, leading to consecutive issues in host software
waiting for an acknowledgement.
2014-06-02 17:11:32 +02:00
Dim3nsioneer
3c927901a4
Implementation of FW extruder change retract
...
FW retraction is extended onto swap retraction invoked by 'G10 S1'.
Bookkeeping of the retract state of all extruders allows for having one
extruder fw standard retracted while another extruder is swap retracted.
An LCD menu item for the swap retract and recover length was added.
2014-06-02 17:02:10 +02:00
Dim3nsioneer
8a32c5395b
renaming the disable inactive extruder feature
2014-06-02 14:07:02 +02:00
Dim3nsioneer
29e7639933
Add switch unused feeder(s) off
...
Having the non-active feeder motors powered on all the time is not
necessary. A feature to deactivate the unused feeder motors has been
implemented. The feature is enabled on default but can be switched off
in the configuration.
2014-06-02 08:13:09 +02:00
Justin Nesselrotte
07c0eeee99
Fixed a comment in the planner
2014-06-01 19:04:41 -05:00
David Forrest
09b84faa00
Configuration.h, pins.h: Add MOTHERBOARD 84 for Teensy++2.0
2014-05-29 17:19:16 -04:00
nothinman
38192cb5f3
Add M112 description to Marlin_main
2014-05-20 15:20:19 +01:00
nothinman
aed5ec008a
Merge pull request #851 from DanNixon/estop
...
Implemented M112
2014-05-19 17:55:34 +01:00
Erik van der Zalm
cfb98ef682
More coverity fixes
2014-05-15 22:09:50 +02:00
zaubara
92e14298b0
Fixes typo for lcd backlighting on I2C PCF8575
...
When using LCD_I2C_TYPE_PCF8575T (like Sainsmart I2C), the backlight
won't come on; the incorrect ifdef blocks the evocation of the backlight
functions.
2014-05-15 01:37:23 +02:00
Erik van der Zalm
9db9842aea
Fixed error found by the free coverity tool ( https://scan.coverity.com/ )
...
===================================================
Hi,
Please find the latest report on new defect(s) introduced to ErikZalm/Marlin found with Coverity Scan.
Defect(s) Reported-by: Coverity Scan
Showing 15 of 15 defect(s)
** CID 59629: Unchecked return value (CHECKED_RETURN)
/Marlin_main.cpp: 2154 in process_commands()()
** CID 59630: Operands don't affect result (CONSTANT_EXPRESSION_RESULT)
/Applications/Arduino.app/Contents/Resources/Java/hardware/arduino/cores/arduino/Tone.cpp: 319 in tone(unsigned char, unsigned int, unsigned long)()
** CID 59631: Missing break in switch (MISSING_BREAK)
/Marlin_main.cpp: 1187 in process_commands()()
** CID 59632: Missing break in switch (MISSING_BREAK)
/Marlin_main.cpp: 1193 in process_commands()()
** CID 59633: Out-of-bounds write (OVERRUN)
/temperature.cpp: 914 in disable_heater()()
** CID 59634: Out-of-bounds write (OVERRUN)
/temperature.cpp: 913 in disable_heater()()
** CID 59635: Out-of-bounds read (OVERRUN)
/temperature.cpp: 626 in analog2temp(int, unsigned char)()
** CID 59636: Out-of-bounds read (OVERRUN)
/temperature.cpp: 620 in analog2temp(int, unsigned char)()
** CID 59637: Out-of-bounds write (OVERRUN)
/temperature.cpp: 202 in PID_autotune(float, int, int)()
** CID 59638: Out-of-bounds read (OVERRUN)
/temperature.cpp: 214 in PID_autotune(float, int, int)()
** CID 59639: Out-of-bounds write (OVERRUN)
/Marlin_main.cpp: 2278 in process_commands()()
** CID 59640: Out-of-bounds read (OVERRUN)
/Marlin_main.cpp: 1802 in process_commands()()
** CID 59641: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 51 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
** CID 59642: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 45 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
** CID 59643: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 32 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
________________________________________________________________________________________________________
*** CID 59629: Unchecked return value (CHECKED_RETURN)
/Marlin_main.cpp: 2154 in process_commands()()
2148 }
2149 #endif
2150 }
2151 }
2152 break;
2153 case 85: // M85
CID 59629: Unchecked return value (CHECKED_RETURN)
Calling "code_seen" without checking return value (as is done elsewhere 66 out of 67 times).
2154 code_seen('S');
2155 max_inactive_time = code_value() * 1000;
2156 break;
2157 case 92: // M92
2158 for(int8_t i=0; i < NUM_AXIS; i++)
2159 {
________________________________________________________________________________________________________
*** CID 59630: Operands don't affect result (CONSTANT_EXPRESSION_RESULT)
/Applications/Arduino.app/Contents/Resources/Java/hardware/arduino/cores/arduino/Tone.cpp: 319 in tone(unsigned char, unsigned int, unsigned long)()
313 else
314 {
315 // two choices for the 16 bit timers: ck/1 or ck/64
316 ocr = F_CPU / frequency / 2 - 1;
317
318 prescalarbits = 0b001;
CID 59630: Operands don't affect result (CONSTANT_EXPRESSION_RESULT)
"ocr > 65535U" is always false regardless of the values of its operands. This occurs as the logical operand of if.
319 if (ocr > 0xffff)
320 {
321 ocr = F_CPU / frequency / 2 / 64 - 1;
322 prescalarbits = 0b011;
323 }
324
________________________________________________________________________________________________________
*** CID 59631: Missing break in switch (MISSING_BREAK)
/Marlin_main.cpp: 1187 in process_commands()()
1181 case 2: // G2 - CW ARC
1182 if(Stopped == false) {
1183 get_arc_coordinates();
1184 prepare_arc_move(true);
1185 return;
1186 }
CID 59631: Missing break in switch (MISSING_BREAK)
The above case falls through to this one.
1187 case 3: // G3 - CCW ARC
1188 if(Stopped == false) {
1189 get_arc_coordinates();
1190 prepare_arc_move(false);
1191 return;
1192 }
________________________________________________________________________________________________________
*** CID 59632: Missing break in switch (MISSING_BREAK)
/Marlin_main.cpp: 1193 in process_commands()()
1187 case 3: // G3 - CCW ARC
1188 if(Stopped == false) {
1189 get_arc_coordinates();
1190 prepare_arc_move(false);
1191 return;
1192 }
CID 59632: Missing break in switch (MISSING_BREAK)
The above case falls through to this one.
1193 case 4: // G4 dwell
1194 LCD_MESSAGEPGM(MSG_DWELL);
1195 codenum = 0;
1196 if(code_seen('P')) codenum = code_value(); // milliseconds to wait
1197 if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait
1198
________________________________________________________________________________________________________
*** CID 59633: Out-of-bounds write (OVERRUN)
/temperature.cpp: 914 in disable_heater()()
908 WRITE(HEATER_0_PIN,LOW);
909 #endif
910 #endif
911
912 #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1
913 target_temperature[1]=0;
CID 59633: Out-of-bounds write (OVERRUN)
Overrunning array "soft_pwm" of 1 bytes at byte offset 1 using index "1".
914 soft_pwm[1]=0;
915 #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1
916 WRITE(HEATER_1_PIN,LOW);
917 #endif
918 #endif
919
________________________________________________________________________________________________________
*** CID 59634: Out-of-bounds write (OVERRUN)
/temperature.cpp: 913 in disable_heater()()
907 #if defined(HEATER_0_PIN) && HEATER_0_PIN > -1
908 WRITE(HEATER_0_PIN,LOW);
909 #endif
910 #endif
911
912 #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1
CID 59634: Out-of-bounds write (OVERRUN)
Overrunning array "target_temperature" of 1 2-byte elements at element index 1 (byte offset 2) using index "1".
913 target_temperature[1]=0;
914 soft_pwm[1]=0;
915 #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1
916 WRITE(HEATER_1_PIN,LOW);
917 #endif
918 #endif
________________________________________________________________________________________________________
*** CID 59635: Out-of-bounds read (OVERRUN)
/temperature.cpp: 626 in analog2temp(int, unsigned char)()
620 if(heater_ttbl_map[e] != NULL)
621 {
622 float celsius = 0;
623 uint8_t i;
624 short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
625
CID 59635: Out-of-bounds read (OVERRUN)
Overrunning array "heater_ttbllen_map" of 1 bytes at byte offset 1 using index "e" (which evaluates to 1).
626 for (i=1; i<heater_ttbllen_map[e]; i++)
627 {
628 if (PGM_RD_W((*tt)[i][0]) > raw)
629 {
630 celsius = PGM_RD_W((*tt)[i-1][1]) +
631 (raw - PGM_RD_W((*tt)[i-1][0])) *
________________________________________________________________________________________________________
*** CID 59636: Out-of-bounds read (OVERRUN)
/temperature.cpp: 620 in analog2temp(int, unsigned char)()
614 if (e == 0)
615 {
616 return 0.25 * raw;
617 }
618 #endif
619
CID 59636: Out-of-bounds read (OVERRUN)
Overrunning array "heater_ttbl_map" of 1 2-byte elements at element index 1 (byte offset 2) using index "e" (which evaluates to 1).
620 if(heater_ttbl_map[e] != NULL)
621 {
622 float celsius = 0;
623 uint8_t i;
624 short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
625
________________________________________________________________________________________________________
*** CID 59637: Out-of-bounds write (OVERRUN)
/temperature.cpp: 202 in PID_autotune(float, int, int)()
196 {
197 soft_pwm_bed = (MAX_BED_POWER)/2;
198 bias = d = (MAX_BED_POWER)/2;
199 }
200 else
201 {
CID 59637: Out-of-bounds write (OVERRUN)
Overrunning array "soft_pwm" of 1 bytes at byte offset 1 using index "extruder" (which evaluates to 1).
202 soft_pwm[extruder] = (PID_MAX)/2;
203 bias = d = (PID_MAX)/2;
204 }
205
206
207
________________________________________________________________________________________________________
*** CID 59638: Out-of-bounds read (OVERRUN)
/temperature.cpp: 214 in PID_autotune(float, int, int)()
208
209 for(;;) {
210
211 if(temp_meas_ready == true) { // temp sample ready
212 updateTemperaturesFromRawValues();
213
CID 59638: Out-of-bounds read (OVERRUN)
Overrunning array "current_temperature" of 1 4-byte elements at element index 1 (byte offset 4) using index "extruder" (which evaluates to 1).
214 input = (extruder<0)?current_temperature_bed:current_temperature[extruder];
215
216 max=max(max,input);
217 min=min(min,input);
218 if(heating == true && input > temp) {
219 if(millis() - t2 > 5000) {
________________________________________________________________________________________________________
*** CID 59639: Out-of-bounds write (OVERRUN)
/Marlin_main.cpp: 2278 in process_commands()()
2272 tmp_extruder = code_value();
2273 if(tmp_extruder >= EXTRUDERS) {
2274 SERIAL_ECHO_START;
2275 SERIAL_ECHO(MSG_M200_INVALID_EXTRUDER);
2276 }
2277 }
CID 59639: Out-of-bounds write (OVERRUN)
Overrunning array "volumetric_multiplier" of 1 4-byte elements at element index 1 (byte offset 4) using index "tmp_extruder" (which evaluates to 1).
2278 volumetric_multiplier[tmp_extruder] = 1 / area;
2279 }
2280 break;
2281 case 201: // M201
2282 for(int8_t i=0; i < NUM_AXIS; i++)
2283 {
________________________________________________________________________________________________________
*** CID 59640: Out-of-bounds read (OVERRUN)
/Marlin_main.cpp: 1802 in process_commands()()
1796 int pin_status = code_value();
1797 int pin_number = LED_PIN;
1798 if (code_seen('P') && pin_status >= 0 && pin_status <= 255)
1799 pin_number = code_value();
1800 for(int8_t i = 0; i < (int8_t)sizeof(sensitive_pins); i++)
1801 {
CID 59640: Out-of-bounds read (OVERRUN)
Overrunning array "sensitive_pins" of 28 2-byte elements at element index 55 (byte offset 110) using index "i" (which evaluates to 55).
1802 if (sensitive_pins[i] == pin_number)
1803 {
1804 pin_number = -1;
1805 break;
1806 }
1807 }
________________________________________________________________________________________________________
*** CID 59641: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 51 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
45 }
46
47 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t enable,
48 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
49 {
50 init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);
CID 59641: Uninitialized scalar field (UNINIT_CTOR)
Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
51 }
52
53 void LiquidCrystal::init(uint8_t fourbitmode, uint8_t rs, uint8_t rw, uint8_t enable,
54 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
55 uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
56 {
________________________________________________________________________________________________________
*** CID 59642: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 45 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
39 }
40
41 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable,
42 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
43 {
44 init(1, rs, rw, enable, d0, d1, d2, d3, 0, 0, 0, 0);
CID 59642: Uninitialized scalar field (UNINIT_CTOR)
Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
45 }
46
47 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t enable,
48 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
49 {
50 init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);
________________________________________________________________________________________________________
*** CID 59643: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 32 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
26
27 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable,
28 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
29 uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
30 {
31 init(0, rs, rw, enable, d0, d1, d2, d3, d4, d5, d6, d7);
CID 59643: Uninitialized scalar field (UNINIT_CTOR)
Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
32 }
33
34 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t enable,
35 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
36 uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
37 {
________________________________________________________________________________________________________
To view the defects in Coverity Scan visit, http://scan.coverity.com/projects/2224?tab=overview
2014-05-14 21:59:48 +02:00
daid
2acd3792fc
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
2014-05-01 12:03:47 +02:00
daid
8b4c4aa5c3
Add feature to check&retry CRC read errors on SD.
2014-05-01 12:03:41 +02:00
nothinman
ce76843dc3
Merge pull request #897 from Makible/5DPrint_D8_Board_Support
...
5DPrint D8 Controller Board Support
2014-04-28 22:11:28 +01:00
Cameron Lai
ad5c8cbba9
Add safety limit for hot bed power in example configuration
2014-04-25 17:04:24 +08:00
Cameron Lai
6460709d92
Fix bug in PID Autotune report
2014-04-25 16:05:05 +08:00
Cameron Lai
105bebb466
Fix for pin mapping for SDSS pin and Fan pin, so Arduino library can be used
2014-04-25 12:57:47 +08:00
Cameron Lai
97ead2eccb
Fix for microstepping pin mapping, not using Teensy pin mapping, but Arduino's default pin mapping so Arduino library can be used
2014-04-25 12:57:11 +08:00
Cameron Lai
d85411f13a
Revert "Fix for stepper microstepping"
...
This reverts commit eea3ba5588
2014-04-25 12:41:56 +08:00
Cameron Lai
7c7f2d094e
Revert "Fix for reading microstepping resolution"
...
This reverts commit 2715f6ddbf
2014-04-25 12:41:48 +08:00
Cameron Lai
e2d703377a
Enable EEPROM by default for 5DPrint D8 Controller Board in example configuration
2014-04-24 19:15:35 +08:00
Cameron Lai
2715f6ddbf
Fix for reading microstepping resolution
2014-04-24 17:48:33 +08:00
Cameron Lai
39e9b133f3
Add example configuration for Makibox printer, which uses the 5DPrint D8 Driver Board
2014-04-24 17:06:07 +08:00
Cameron Lai
da6b536182
Add 5DPrint D8 Driver Board info and temperature table for Makibox hot bed
2014-04-24 16:49:42 +08:00
Cameron Lai
3a8e36f19e
Add Digipot config for 5DPrint D8 Driver Board
2014-04-24 12:56:46 +08:00
Cameron Lai
eea3ba5588
Fix for stepper microstepping
2014-04-24 12:56:06 +08:00
Cameron Lai
1cbcbb0971
Add makibox machine information
2014-04-24 12:55:21 +08:00
Cameron Lai
2fa514e88a
Add port for 5DPrint D8 Driver board
2014-04-24 12:55:00 +08:00
nothinman
b9126ab497
Merge pull request #894 from MyMakibox/Marlin_v1
...
Update Marlin_main.cpp
2014-04-23 16:23:56 +01:00
MyMakibox
21ec6b88c3
Update Marlin_main.cpp
...
Added description of autotemp flags to M109
2014-04-23 17:33:26 +08:00
MyMakibox
e4dc80d3d3
Update Configuration_adv.h
...
Corrected error in AUTOTEMP instructions
2014-04-23 17:30:07 +08:00
whosawhatsis
27d544ac25
Speed up QUICK_HOME feedrate for diagonal move
...
Speed up the diagonal move while still keeping each individual axis at
or below its homing feedrate.
2014-04-19 17:29:20 -07:00
nothinman
013793bbe9
Merge pull request #878 from koldoartola/Marlin_v1
...
Added new language (Basque-Euskera)
2014-04-13 22:37:39 +01:00
koldo artola
e5b70237c7
Added new language (Basque-Euskera)
...
Added:
* new language (Basque-Euskera)
* some minor corrections for Spanish
* added 2 new constants for every language (required for a minor change
I am preparing to ultralcd.cpp)
2014-04-13 22:19:38 +02:00
Nutz95
ed6f4a71c5
fix wrong temptable index
2014-04-13 18:00:55 +02:00
Nutz95
3161740df9
This table is made for thermistor 3950 (can be found on ebay for cheap)
...
it's caracteristics are :
R25℃ ;100KΩ±1%
B Value(R25/50℃)：3990K 1%
Dissipation Factor(mW/℃)：1.1~1.6 In still Air
Thermal Time Constant(S)：10~17 In Still Air
Operating temperature range： (-50~+260°C)
Dimension： 1.8mm Dia X4.1mm
Lead Length ：30mm
This table was found on the following blogs:
http://cae2100.wordpress.com/2014/03/08/beta3950-thermistor-table-for-marlin/
and
http://microfabricator.com/articles/view/id/531ad7e59aad9d3131000000/beta-3950-thermistor-table-for-marlin
2014-04-13 17:03:20 +02:00
nothinman
086ff1644f
Merge pull request #852 from pixatintes/patch-1
...
Update language.h
2014-04-13 00:46:17 +01:00
nothinman
3ffc9651b1
Merge pull request #845 from DerSchultze/Sanguinololu-servo
...
Added servo pin assignments to Sanguinololu
2014-04-13 00:37:28 +01:00
nothinman
357b87b498
Merge pull request #826 from paciotti/patch-1
...
Configuration_adv.h
2014-04-13 00:22:25 +01:00
Gabe Rosenhouse
27a7cf9fcf
use existing strings
2014-04-07 05:01:48 -05:00
Gabe Rosenhouse
d3f305332a
Allowable range now includes default value
2014-04-06 19:45:56 -05:00
Gabe Rosenhouse
b0aeac117f
Adjustable Z probe offset, via custom M-code
2014-04-06 19:45:56 -05:00
nothinman
c23376f2e7
Merge pull request #837 from whosawhatsis/fwretract
...
FWRETRACT in mm/s
2014-04-04 11:47:58 +01:00
nothinman
dfb98101e4
Change CONTROLLERFAN_PIN for board 35 to -1, as it would conflict with board's 33 extruder pin, causing burnout (it's the same board, just different number of fans/extruders, therefore should be pin-compatible)
2014-04-03 18:05:48 +01:00
nothinman
f1501317ca
Merge pull request #860 from drf5n/therm3950
...
thermistortables.h: Add comments that table 60 uses beta=3950.
2014-04-02 18:29:57 +01:00
nothinman
9a5d23d96f
Merge pull request #866 from sakunamary/Marlin_v1
...
fix bug for dual extruders not working
2014-04-02 18:27:42 +01:00
nothinman
303ee67896
Merge pull request #864 from whosawhatsis/M200
...
fix bug in M200 with multiple extruders
2014-04-02 18:26:15 +01:00
Tim
8759508319
fix bug for dual extruders not working
...
some guy find that marlin not working good for dual extruders delta .
when type T0 or T1 to active extruder and E0 or E1 move causing XYZ
motion . so i locales the bugs and fix it , I have dry run the fix.
2014-04-01 09:26:19 +08:00
whosawhatsis
a65564eef6
fix bug in M200 with multiple extruders
2014-03-30 11:42:22 -07:00
whosawhatsis
aeaf9b9312
fix bug in M200 with multiple extruders
2014-03-30 11:41:57 -07:00
David Forrest
b0093a1513
thermistortables.h: Add comments that table 60 uses beta=3950.
2014-03-26 23:41:10 -04:00
pixatintes
a3530d1141
Update language.h
...
Updated to latest version.
2014-03-23 18:06:48 +01:00
pixatintes
990e770e15
Update language.h
...
Added catalan language
2014-03-23 10:30:08 +01:00
Dan Nixon
f643f4d674
Test and refactor
2014-03-21 20:42:00 +00:00
Dim3nsioneer
c8cdd1fc6f
Bugfixes for language option 6 (russian)
2014-03-19 14:27:38 +01:00
Dim3nsioneer
7395dafc1e
semantic changes in language.h
2014-03-19 12:30:50 +01:00
Dim3nsioneer
fad2a60ce6
Corrections for preheat extension in language.h
2014-03-19 12:23:35 +01:00
Ralf Schultz
eecda434fb
Sanguinololu servo pins set default disabled
2014-03-18 08:25:20 +01:00
Dim3nsioneer
944ced87c5
Extended Preheat options
...
Preheat LCD menus base on code by D-Base
2014-03-17 18:37:46 +01:00
Ralf Schultz
06709ad60e
Added servo pin assignments to Sanguinololu
2014-03-17 15:45:13 +01:00
Dim3nsioneer
3906f27c46
Individual extruder flow rate
...
Extension of M221, Tune menu
2014-03-15 18:09:46 +01:00
Dan Nixon
a38c90ee84
Added estop handling
2014-03-15 15:56:15 +00:00
ErikZalm
a00cec8b71
Merge pull request #833 from mattsch/optional_feedrate_multiplier
...
Add support for disabling encoder control for feedrate multiplier
2014-03-15 15:41:45 +01:00
Dan Nixon
272072fa20
Added M112
2014-03-14 23:19:43 +00:00
whosawhatsis
aab61e63c3
FWRETRACT in mm/s
...
Firmware retraction now stores the retract and recover speeds in mm/s
instead of mm/min. This makes it match the units of the maximum
feedrate, and fixes problems with modifying the value via LCD control
panel. From gcode, the values are still taken in mm/min to match the
units of G1 and similar, and they are converted to mm/s before they are
stored.
I also lowered the default retract feedrate to make it less likely to
cause problems for geared extruders when the user hasn’t bothered to
set a reasonable maximum feedrate, though users should be setting both
of these values to suit their hardware.
2014-03-14 15:17:28 -07:00
Matthew Schick
6cd85e6008
Add support for disabling encoder control for feedrate multiplier
...
Signed-off-by: Matthew Schick <matthew.schick@gmail.com>
2014-03-12 18:13:50 -04:00
blddk
09af1b90b8
Added CHDK support
...
Added CHDK support to take pictures instead of doing an IR command, see more about how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
2014-03-10 21:57:08 +01:00
blddk
765b2da3d4
Added CHDK support
...
Added so M240 can be used to trigger CHDK instead of sending an IR signal, see more about CHDK here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
2014-03-10 21:52:33 +01:00
paciotti
881e348eed
Update Configuration_adv.h
...
Increase Z_HOME_RETRACT_MM to 2mm default to avoid end stop not switching during retract.
2014-03-08 22:35:05 +01:00
