14df753086
Correction for block->mix_steps
...
Fix #11484
2018-09-29 19:13:17 -05:00
2ecfda80ac
Improve support for JTAG/SWD pins reuse ( #11963 )
...
STM32 can reuse JTAG and SWD pins separately. Add `DISABLE_DEBUG` option to disable both interfaces and retain `DISABLE_JTAG` to disable JTAG only.
2018-09-29 19:00:49 -05:00
bb47009656
Apply sensorless changes to example configs
2018-09-29 18:54:14 -05:00
3286325044
Add TMC2130 sensorless probing
2018-09-29 18:54:14 -05:00
7d5c336c56
Corrections for dylsexic TMC
2018-09-29 18:51:11 -05:00
71d06ef1b2
Make opt_set, opt_set_adv, pins_set also enable
2018-09-29 18:36:33 -05:00
d89d8fe852
Fix Busy State in temperature.cpp
...
Fix #11954
2018-09-29 17:03:35 -05:00
70e7a465d8
[2.0.x] Fix compile error ( #11951 )
...
Fix compile error intruduced with M109 modification
2018-09-29 13:48:23 -05:00
935b120949
Anycubic Kossel: probe closer to the edge ( #11950 )
2018-09-29 02:26:16 -05:00
1410e79e7f
Ensure M109 handles autotemp
2018-09-29 02:12:06 -05:00
e4389f7d23
Standard methods to wait for heating ( #11949 )
2018-09-29 01:44:47 -05:00
bdc9889d3a
Fix a sanity check
2018-09-29 00:24:25 -05:00
321f9140d1
Followup to #11904
2018-09-28 20:04:40 -05:00
23114aeb81
Fix garbled M119 output. Honor NUM_RUNOUT_SENSORS ( #11948 )
2018-09-28 19:00:11 -05:00
1667ed9d1c
Pause should use ECHOLNPGM
2018-09-28 18:15:38 -05:00
93839e2f73
Add option to enable/disable autoretract altogether ( #11904 )
2018-09-28 16:52:56 -05:00
ad21a4f07b
Tweaks to HAL format and order
2018-09-28 15:59:50 -05:00
b682a1961a
Tweak STM32F7 TMC2660 class
2018-09-27 21:13:15 -05:00
a0a3b23e35
Reduce Raptor bootscreen by 144 bytes
2018-09-27 18:24:40 -05:00
95d793456b
Add Formbot Raptor config, fix other Formbot configs ( #11926 )
2018-09-27 19:20:43 -04:00
d016b572e3
[2.0.x] Add pin configuration for Fysetc F6 ( #11932 )
2018-09-27 19:20:19 -04:00
84926b1d5a
HAL general support for DISABLE_JTAG option ( #11211 )
...
Some STM32-based boards may use multiplexed JTAG pins as IO. Up to now the `DISABLE_JTAG` option (defined in pins files) was only supported for AT90-based boards. This commit generalizes the code and adds support for boards based on STM32F1 and STM32F4.
2018-09-27 19:02:50 -04:00
c575c5d5f6
Bring example configs up to date ( #11939 )
2018-09-27 18:47:26 -04:00
6b1a4f30a8
Fix case of T-Rex 3 _Statusscreen.h
2018-09-27 17:00:55 -05:00
ab7bfa86e2
Fix case of T-Rex-3 _Statusscreen.h
2018-09-27 17:00:55 -05:00
241168926d
Update some configs
2018-09-27 16:42:59 -05:00
cb6454118c
Workaround for Pronterface M29
2018-09-27 16:27:02 -05:00
eeab4141db
[2.0.x] Anycubic Trigorilla 14 pins tweak ( #11869 )
2018-09-27 16:06:21 -04:00
cb9dc56630
Add GT2560 v3 support ( #11914 )
2018-09-27 15:13:15 -04:00
f2e630a05e
Stow probe on probing failed ( #11936 )
...
Prevents probe from being left down should probing fail and print job continue
2018-09-27 13:26:14 -04:00
0b602ae101
[2.0.x] Fix Anycubic Kossel with Probe V1, stuck LCD message after stow ( #11929 )
2018-09-27 13:23:53 -04:00
dc11131656
[2.0.x] fix possible race condition ( #11923 )
...
Fix some commits done in #11900
2018-09-25 13:56:57 -04:00
d6b9327c11
Followup for Endstop Noise Threshold
...
Followup to #11912
2018-09-25 13:50:49 -04:00
aa6e8e9325
Tweak some config comments
2018-09-25 13:42:28 -04:00
5490a664f5
Expose: Homing Validation and Endstop Noise Threshold ( #11912 )
2018-09-24 21:59:12 -04:00
cee34f7290
Followup for BABYSTEP_HOTEND_Z_OFFSET ( #11916 )
2018-09-24 21:46:56 -04:00
884ad75cb8
Update config files
2018-09-24 17:26:18 -04:00
18e456d38d
[2.0.x] fix home endstop bug (DON'T MERGE, needs discussion) ( #11900 )
2018-09-24 16:56:01 -04:00
6742026568
Followup for 6 extruders
2018-09-24 14:36:50 -04:00
04bdff4115
Add a blank line
2018-09-24 12:49:02 -04:00
ccbd045f02
Fixed warning about comparing signed to unsigned ( #11909 )
2018-09-24 12:03:29 -04:00
1104054d73
2.0 IDEX Independent z offset and other fixes ( #11862 )
...
* Add Formbot Raptor board
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com >
* Add a second Z probe Z offset
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com >
* Modify method to utilize live adjustment of hotend z offset
Should probably move config option to babystepping and rename as it may now apply to all multiextruder systems
* Move config item and catchup other code to current method
2018-09-24 09:40:48 -05:00
217e0efd20
General option PAUSE_BEFORE_DEPLOY_STOW ( #11905 )
2018-09-24 00:43:43 -04:00
849dea92a8
Move probe extras below probe types
2018-09-23 23:23:07 -04:00
a2b0260f0f
Update Sublime files
2018-09-23 19:59:08 -04:00
a4cdffdd69
Support for manually deployed fixed probes ( #11899 )
2018-09-23 19:59:08 -04:00
ddcbf80f23
Followup for Z_TRIPLE_ENDSTOPS
2018-09-23 12:22:31 -04:00
c411e7eb0d
[2.0.x] Squelch compiler warnings seen with -Wall ( #11889 )
2018-09-23 12:00:34 -04:00
83105590a0
Better default values for Mesh Inset
2018-09-22 03:25:18 -04:00
4163c1a514
Fix end stop and Z-probe reporting logic
2018-09-22 03:25:18 -04:00
