Commit Graph

83 Commits

Author SHA1 Message Date
Marcio Teixeira
6a8fb0f25f Simplify backlash compensation code. (#12813)
- Use `TEST(dm,axis)` to determine directions instead of doing comparisons.
- Remove recomputation of `millimeters` and `delta_mm` since backlash compensation should not affect the distance over which material is extruded.
2019-01-04 13:30:56 -06:00
Marcio Teixeira
b22716e938 M425 Backlash Correction (#11061) 2018-12-08 14:36:46 -06:00
Jacob Jordan
8be91677df Fix Skew factors (#12555)
- Ensure Skew factors are calculated from test square measurements
2018-11-29 11:39:31 -06:00
Marcio Teixeira
056561df93 [2.0.x] Enhancements to FILAMENT_RUNOUT_SENSOR (#12069)
- Added FILAMENT_RUNOUT_DISTANCE_MM option
- Added FILAMENT_MOTION_SENSOR option
2018-10-16 07:28:52 -05:00
AnHardt
f56968ba0b New Continuous Filament Mixer (#12098) 2018-10-16 03:38:57 -05:00
Scott Lahteine
d556dc1865
Fix and improve EEPROM storage (#12054)
* Clean up Temperature PID
* Improve EEPROM read/write/validate
* Group `SINGLENOZZLE` saved settings
* Group planner saved settings
* Group filament change saved settings
* Group skew saved settings
* Group `FWRETRACT` saved settings
2018-10-10 09:45:20 -05:00
Scott Lahteine
d6b0fbd771
Use uint8_t for all fan speeds (#12032) 2018-10-07 15:34:41 -05:00
Scott Lahteine
c5e5cc5e9f Fix some trailing whitespace, macros 2018-09-17 17:30:04 -05:00
Thomas Moore
c437bb08f1 Overhaul of the planner (#11578)
- Move FWRETRACT to the planner
- Combine leveling, skew, etc. in a single modifier method
- Have kinematic and non-kinematic moves call one planner method
2018-09-16 21:24:15 -05:00
Scott Lahteine
d882717d98
Save some PROGMEM with constexpr (#11798)
When possible, make `active_extruder` a `constexpr` to save some PROGMEM.
2018-09-10 23:09:26 -05:00
Sam Lane
4f883d5971 [2.0.x] Extruder-Distinct Linear Advance K Factors (#11789) 2018-09-10 22:37:32 -05:00
Scott Lahteine
a4b0148365 Easier to find 'static inline' 2018-08-13 23:55:33 -05:00
etagle
1367df2875 Replace double with float, optimize calculation 2018-07-04 22:28:56 -05:00
Scott Lahteine
8eaac0dab3
Add delta feedrate scaling (#11153) 2018-06-30 13:44:27 -05:00
Scott Lahteine
bd7f5848f1
Remove JUNCTION_DEVIATION_INCLUDE_E option (#11147) 2018-06-29 22:42:05 -05:00
Eduardo José Tagle
edb21f349a Fix stepper/planner block handling, race conditions (#11098)
- Allow planner to alter the deceleration phase of the currently executing block.
- Remove BUSY flag, as it is NON ATOMIC to set bits in the Stepper ISR and Planner at the same time.
2018-06-27 18:11:16 -05:00
Andy Shaw
3b3029c4bf Make max_e_jerk an array to reduce CPU usage (#11118) 2018-06-26 22:38:31 -04:00
Scott Lahteine
50b6204079 Fix LIN_ADVANCE max_e_jerk_factor
According to https://github.com/MarlinFirmware/Marlin/issues/9917#issuecomment-399204568
2018-06-21 22:02:34 -04:00
Scott Lahteine
9d04f47d98 Improvements for junction_deviation_mm
- Drop `max_jerk` with `JUNCTION_DEVIATION`
- Add `max_e_jerk_factor` for use by `LIN_ADVANCE`
- Recalculate `max_e_jerk_factor` when `junction_deviation_mm` changes
- Fix LCD editing of `junction_deviation_mm`
2018-06-11 22:05:16 -05:00
Scott Lahteine
a2f521d34b
Add Junction Deviation mm runtime setting (#10990) 2018-06-10 18:02:54 -05:00
etagle
39a7e7720d Adaptive multiaxis step smoothing
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
2018-06-10 16:02:47 -05:00
Scott Lahteine
2deff0d9b9 Fix/Improve junction deviation
- Respect axis max acceleration limits instead of forcing a fixed acceleration value.
- The `junction_unit_vec` ensures proper handling of entry and exit speeds even when the axes involved have different limits.
2018-05-31 20:09:53 -05:00
Scott Lahteine
d259070980 Clean up trailing spaces from vim, etc. 2018-05-31 00:09:41 -05:00
Scott Lahteine
aaaf09bda2 BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION 2018-05-26 18:33:51 -05:00
Scott Lahteine
435ecb6b67 Followup to stepper/planner refactor 2018-05-20 23:13:38 -05:00
etagle
a4af975873 Fix planner block optimization
- Fixed the planner incorrectly avoiding optimization of the block following the active one.
- Added extra conditions to terminate planner early and avoid redundant computations.
2018-05-20 07:10:24 -05:00
etagle
e0ca627033 Planner block HOLD flag
Allows the Stepper ISR to wait until a given block is free for use. Allows Planner to plan the first move, which is split into two.
2018-05-20 06:23:58 -05:00
etagle
a11eb50a3e Refactor and optimize Stepper/Planner
Better encapsulation and considerably reduce stepper jitter
2018-05-20 06:23:58 -05:00
Scott Lahteine
99ecdf59af Smarter MIN, MAX, ABS macros
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.

Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-05-13 04:52:56 -05:00
Scott Lahteine
8f8c6a9bc4
Move get_axis_position_mm to Planner (#10718) 2018-05-12 09:59:11 -05:00
Scott Lahteine
306f0f2135
Move Stepper::synchronize to Planner (#10713)
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
2018-05-12 01:38:02 -05:00
Scott Lahteine
a225d2e99e Fix compilation with UBL and Arc/Bézier
Fix #10660
2018-05-09 00:40:37 -05:00
Scott Lahteine
19f189b4e5
Add UBL support for G2/G3 and G5 (#10648) 2018-05-08 11:10:45 -05:00
Scott Lahteine
af1950a63e Improve sync of stepper positions 2018-05-06 01:24:14 -05:00
Scott Lahteine
d7b699ec34 Fewer includes of vector_3.h 2018-05-01 07:05:18 -05:00
Scott Lahteine
36b97bde9f clear_block_buffer, kill_current_block in quick_stop 2018-04-13 22:04:53 -05:00
Eduardo José Tagle
57a899a412 [2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR (#10373) 2018-04-11 18:13:42 -05:00
etagle
a29adde5c0 Implement BEZIER_JERK_CONTROL
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
2018-04-07 21:03:28 -05:00
Scott Lahteine
e8e60263c8 Scale feedrate (mm/s to deg/s) for SCARA 2018-04-06 19:47:48 -05:00
Scott Lahteine
1cb810ff1c
[2.0.x] Automatically reset stepper timeout (#10179)
* Automatically reset stepper timeout in manage_inactivity

Any code that adds moves to the planner can skip resetting the stepper timeout. We can let `idle` / `manage_inactivity` reset the timer whenever it detects any moves in the planner.

* blocks_queued => has_blocks_queued
2018-03-21 19:30:06 -05:00
Scott Lahteine
2057177184 Make enums into implicit char 2018-03-06 23:39:56 -06:00
Scott Lahteine
930720bbbb
Fix broken reverse planner (#9943)
From #9914 by @Sebastianv650
2018-03-04 21:19:06 -06:00
Scott Lahteine
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 (#9712) 2018-02-23 00:53:29 -06:00
Thomas Moore
786746404b [2.0.x] Apply feedrate to nozzle movement for kinematic machines (#8778) 2018-02-04 00:26:05 -06:00
Scott Lahteine
4f5e087ff4 Planner anti-stutter by Sebastian Popp 2018-01-14 21:07:10 -06:00
Scott Lahteine
5bc2acc072 Restore position_float to fix LIN_ADVANCE 2017-12-21 16:45:46 -06:00
Scott Lahteine
933f76fda3 Option to disable all volumetric extrusion 2017-12-19 19:51:25 -06:00
Scott Lahteine
09d13f186f
Correct unskew, after all 2017-12-15 14:24:20 -06:00
Scott Lahteine
368c124de8 Fix Planner::unskew parity with skew 2017-12-13 17:46:48 -06:00
Scott Lahteine
cf2193c07f Comment, fix filament width sensor 2017-12-13 02:32:34 -06:00