Commit Graph

406 Commits

Author SHA1 Message Date
Scott Lahteine
05fca752d6 Clean up autostart handling 2018-05-01 01:35:57 -05:00
Scott Lahteine
05c33833e7
[2.0.x] Add NO_LCD_MENUS option (#10582) 2018-04-30 21:16:31 -05:00
Scott Lahteine
59fda986ea Allow Z_AFTER_PROBING to be 0 2018-04-30 03:25:47 -05:00
Scott Lahteine
9e0d99c0c6
Round all floats in string conversion functions (#10566) 2018-04-29 00:51:36 -05:00
Scott Lahteine
cd08f01bb4 Fix M421 comment in gcode.h 2018-04-28 11:16:52 -05:00
Scott Lahteine
8db7fb226a Fix M420 C for UBL 2018-04-28 08:14:20 -05:00
Marcio Teixeira
724e9f56c8 Removed "const" to match parser. (#10548) 2018-04-27 17:48:52 -05:00
Giuliano
2e1939e85c [2.0.x] report error on unsupported commands (#10553)
Raise an error when an unknown/unsupported G/M command is requires.

This will address #10546
2018-04-27 17:40:27 -05:00
Scott Lahteine
a51ba6e3f6 Fix ABL grid bounds test for Delta/SCARA
Addressing #10538
2018-04-27 02:23:10 -05:00
Scott Lahteine
63e0b36f8b Fix G29_RECOVER_COMMANDS typo 2018-04-27 02:23:10 -05:00
Scott Lahteine
eef0248a1c
Add M420 C to adjust the whole mesh (#10522) 2018-04-25 06:43:45 -05:00
Marcio Teixeira
02a711c4d6 [2.0.x] Fix crash upon repeated calls to process_subcommands_now_P (#10509) 2018-04-24 13:44:22 -05:00
Scott Lahteine
f06c3c38b9 Fix M0_M1 with no LCD 2018-04-24 09:22:05 -05:00
Scott Lahteine
f423e54f77 Strip trailing spaces 2018-04-23 18:00:43 -05:00
Scott Lahteine
cb46cb8480
Add HAS_HEATED_BED conditional (#10495) 2018-04-23 17:13:01 -05:00
Scott Lahteine
1c3d49afe0 Fix G28 with Z_AFTER_PROBING
Fix #10476
2018-04-22 01:23:26 -05:00
Scott Lahteine
023385ca59
Merge pull request #10479 from thinkyhead/bf2_creality_power_loss_resume
[2.0.x] Creality3D Power-Loss Recovery
2018-04-22 00:17:44 -05:00
Scott Lahteine
3396671011
[2.0.x] Reset LCD status to fallbacks (#10470)
* Remove obsolete strings
* Tweak some static consts
* Reset LCD status to fallbacks
2018-04-22 00:16:30 -05:00
Scott Lahteine
11ab017dd0 Creality3D Power-Loss Recovery 2018-04-21 21:56:50 -05:00
Scott Lahteine
7dcd0a1cff Add R parameter to G28 to specify pre-raise 2018-04-21 19:07:48 -05:00
Scott Lahteine
a90cbc6339
[2.0.x] Wait for bed heaters between probing (#10472) 2018-04-21 15:43:21 -05:00
Scott Lahteine
d8a8eec6ea Add THERMAL_PROTECTION capability
Based on #10465

In response to `M115` the firmware reports if Thermal Protection is enabled (1) or not (0). This information can be used by software such as OctoPrint (more precisely the Printer Safety Check plugin) to warn users when Thermal Protection is not enabled in the firmware.

Co-Authored-By: andrivet <sebastien@advtools.com>
2018-04-20 16:50:50 -05:00
Scott Lahteine
65a6a86d19 Don't report point 0 in MBL G29 2018-04-20 13:12:50 -05:00
Marcio Teixeira
5cc7916e69 Add G29_RETRY_AND_RECOVER feature
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
2018-04-19 19:45:53 -05:00
Scott Lahteine
78ea4871f9 Fix up enqueue now functions
…and apply to MALYAN_LCD.
2018-04-19 19:45:53 -05:00
Scott Lahteine
df2f24617b Use 0 as the bed position (not Z_MIN_POS) 2018-04-17 20:32:56 -05:00
Scott Lahteine
52c024e260 M221 with no parameters report flow 2018-04-17 16:06:25 -05:00
Scott Lahteine
0746aff595 Improve UBL mesh report. Add M420 T, M421 N 2018-04-17 15:52:56 -05:00
Scott Lahteine
99282a46e9 Make sure ABL (manual) starts close to the bed 2018-04-13 20:19:30 -05:00
Scott Lahteine
3c5c6d478a Prettify process_parsed_command 2018-04-13 00:23:11 -05:00
Scott Lahteine
bb7064cc30 Tweak MBL move to bed code 2018-04-12 22:43:02 -05:00
Scott Lahteine
daa712455b Make sure MBL starts close to the bed
Fix #10390
2018-04-12 19:36:37 -05:00
Scott Lahteine
4c8751727a Fix M118 parameter handling
Fix #10388
2018-04-12 19:10:04 -05:00
Luc Van Daele
646aa20b43 Overhaul of G33 Delta Calibration (#8822) 2018-04-11 21:14:48 -05:00
Luc Van Daele
ac2e0afb62 Low Point for delta calibration (#10363) 2018-04-11 18:59:46 -05:00
Sean
2d9b0a66fe Add Filament Change accelerations 2018-04-09 23:57:27 -05:00
Scott Lahteine
8b8ad14178 Add Z_PROBE_LOW_POINT to prevent damage 2018-04-09 17:23:03 -05:00
Scott Lahteine
cea398849e Tweak to gcode_line_error/return 2018-04-07 21:25:49 -05:00
Scott Lahteine
e8e60263c8 Scale feedrate (mm/s to deg/s) for SCARA 2018-04-06 19:47:48 -05:00
Marcio Teixeira
8bc93c6f2b Improve heating/cooling LCD messages (#10293) 2018-04-04 18:29:27 -05:00
Scott Lahteine
241996d5d6
Merge pull request #10257 from thinkyhead/bf2_tool_change_debug 2018-04-02 19:33:45 -05:00
Scott Lahteine
adcb87f0db Z Endstop Servo => Z Probe Servo 2018-04-01 23:54:21 -05:00
Scott Lahteine
1a75165f35 For set_z_fade_height use set_bed_leveling_enabled 2018-03-31 22:43:05 -05:00
Scott Lahteine
55e9b85ad6 Clear the "Wait for user" message set by M0/M1
See https://github.com/MarlinFirmware/Marlin/issues/10246#issuecomment-377146936
2018-03-29 18:38:12 -05:00
AnHardt
c1f58a238d No delay in sensorless quick homing (#10254) 2018-03-29 16:10:20 -05:00
Scott Lahteine
1be955e52a Alert users about low Z jerk values 2018-03-28 23:08:33 -05:00
Scott Lahteine
9e4c037cef
Wait before turning off PRINTER_EVENT_LEDS at print end (#10248) 2018-03-28 22:59:28 -05:00
Scott Lahteine
7b8bb2519e Fix gcode_line_error call
Followup to 3007eee
2018-03-28 20:29:41 -05:00
Scott Lahteine
aa20b3ef7c Fix linear/3-point manual leveling buffer overrun
Fixes #10137
2018-03-28 18:41:22 -05:00
Scott Lahteine
38378cd0e8 M218 with DELTA needs planner.h
Fix #10232
2018-03-28 17:05:14 -05:00