779b2709ec
Change temperature pin order for RemRam V1 ( #12458 )
...
Beta testers suggested to adopt the RAMPS order of temperature probe connectors. This commit fixes the order to the RAMPS order.
2018-11-17 16:51:06 -06:00
8ebb4dc294
Followup to static CardReader
2018-11-17 07:52:35 -06:00
7ee5894360
Allow float XY probe offsets
...
Responding to #12383
XY probe offsets should be integers because adding decimal points makes the code larger. But if decimals are very much wanted, this commit removes the old restriction.
2018-11-17 07:44:47 -06:00
43ecdb606f
Fix a compile warning ( #12452 )
2018-11-17 07:08:25 -06:00
984c4ba8c7
Enable SD Card on RepRap Display and RADDS ( #12446 )
...
* Enable SD Card on RepRap Display and RADDS
Define the necessary pins in `pins_RADDS.h` (copied from the `RADDS_DISPLAY` section) for the use of the SD card slot on RRD.
2018-11-17 06:59:40 -06:00
56a94c2a26
Use 'target_extruder' in M104 as with M109 ( #12448 )
2018-11-17 06:55:25 -06:00
66580f32c2
Make CardReader class static ( #12451 )
...
* Make CardReader a static class
* Make CardReader flags into bitfields
2018-11-16 22:39:16 -06:00
3e9ffaddb6
Consolidate, optimize some LCD menu code ( #12450 )
2018-11-16 21:44:48 -06:00
d97e31db4c
Optimize Power-Loss Recovery ( #12440 )
2018-11-16 20:47:07 -06:00
ca21ac6b9b
Support two MAX6675 thermocouples ( #8686 )
2018-11-16 18:20:33 -06:00
0e610815e4
No need for Cap:PAREN_COMMENTS
2018-11-16 04:28:40 -06:00
7a075a5dc9
Tweak extruder errors
2018-11-16 01:32:21 -06:00
2d92f333f5
Fix GcodeSuite::T active_extruder reference
2018-11-15 14:07:24 -06:00
d2bb53702a
Optimize target_extruder, ignore T with mixing ( #12432 )
...
* Optimize target_extruder, ignore T with mixing
* Give G-code Tn parity with tool_change
2018-11-14 17:33:04 -06:00
5e586a6b39
Fix to runout sensor code. ( #12431 )
...
- "old_state" is no longer a class static variable.
2018-11-14 16:54:05 -06:00
d82c350de7
Miscellaneous LCD code renaming, reordering ( #12430 )
...
* Move special characters to language.h
* Apply some naming standards
* Clean up menu item draw functions
* Rename some Temperature methods
* UI => ExtUI
2018-11-14 13:13:51 -06:00
edfd106bc5
Rejigger Filament Runout class ( #12428 )
2018-11-14 11:45:57 -06:00
f4c128ecaa
Move RRW keypad code to a common method ( #12429 )
2018-11-14 06:00:21 -06:00
54ec5528a0
hasstatus => has_status
2018-11-14 01:34:28 -06:00
ebf585b673
Fix an old sanity check
2018-11-14 01:15:35 -06:00
052d102ded
UltiMachine Archim 1 support ( #12404 )
2018-11-14 00:27:39 -06:00
664e20754d
Clean up pins files
2018-11-14 00:23:33 -06:00
1eb5249598
Fix Formbot Trex-2+ configs
...
Followup to #12422
2018-11-13 21:53:54 -06:00
075a22ed65
Update Portuguese-Brazilian translation ( #12402 )
2018-11-13 19:42:25 -06:00
3ceab8474c
Add required "cardreader.h" include ( #12419 )
2018-11-13 17:12:44 -06:00
98c2fc4e42
Endstops fix followup ( #12423 )
...
Followup to #12413
2018-11-13 17:10:07 -06:00
f19fd642ce
Updates to Formbot T-Rex 2+ configuration files ( #12422 )
...
Updates to Formbot T-Rex 2+ configuration files
2018-11-13 13:48:35 -06:00
cda5ef08fa
Debug of G2-G3 for UBL ( #12386 )
...
Changes only affect UBL. Everything else is left alone.
2018-11-13 11:20:21 -06:00
9ad3aed0ef
Fix tool-change for MIXING_EXTRUDER with < 2 virtual tools ( #12417 )
...
Fix #12416
Better handling of `ENABLED(MIXING_EXTRUDER) && !MIXING_VIRTUAL_TOOLS > 1` - to not fall through to the general case. Fix compiler warnings for `#elif EXTRUDERS < 2`.
2018-11-13 04:56:10 -06:00
d631267548
Refine endstops fixes ( #12413 )
...
When endstops/probe are enabled `ENDSTOP_NOISE_THRESHOLD` calls to `update` are required to properly re-sync endstops/probe status.
2018-11-13 04:31:58 -06:00
0ee1a92971
Group status methods, share reset_status with Extensible UI ( #12414 )
...
* Group status methods, share reset_status with Extensible UI
* Move common DOGM code to headers
2018-11-13 01:47:45 -06:00
690c4e8457
Clean TLM trailing whitespace
2018-11-13 00:03:34 -06:00
143b2896e0
Add M412 to enable/disable filament runout detection ( #12406 )
2018-11-12 21:29:46 -06:00
a163c89c6a
Followup to 50af1d1
2018-11-12 20:31:53 -06:00
be6271767f
Fix BABYSTEP_ZPROBE_OFFSET ( #12408 )
...
Fix #12399
Did not compile without `WATCH_HOTENDS || WATCH_THE_BED`.
Add condition to include "../../module/temperature.h".
2018-11-12 17:44:21 -06:00
50af1d1e08
Differentiate translated On/Off from Serial ON/OFF
2018-11-12 17:23:08 -06:00
df907a905f
Update UBL comments for debug change
2018-11-12 03:46:48 -06:00
da17f8ad37
For now (!) don't synchronize in M204 and M205
...
See if this has any deleterious effect on motion planning by slicers that inser their own jerk and acceleration controls. The problem I see is that these settings can take effect on blocks already in the planner, and the only way around this would be to shadow these settings in planner blocks and use the shadowed settings in the planner.
2018-11-12 02:43:24 -06:00
a3923424c7
Clean up LCD width/height determination
2018-11-12 02:37:40 -06:00
a0c795b097
Encapsulate common display code in a singleton ( #12395 )
...
* Encapsulate common LCD code in a singleton
* Depend more UBL code on UBL_DEVEL_DEBUGGING
- Since most users don't need the debugging on at all times, this helps reduce the default build size for UBL by over 2K, a little closer to fitting on 128K boards.
2018-11-11 12:16:24 -06:00
9da6809ac3
Adjust some comment spacing
2018-11-11 11:28:50 -06:00
471f403a67
Reduce code size with plain inlines
2018-11-11 08:36:10 -06:00
30a49f5ee2
Apply extra condition to LCD_PROGRESS_BAR
2018-11-11 08:36:10 -06:00
4e0c935959
Update HAL and libs formatting
2018-11-10 19:43:23 -06:00
47483e8c17
Update Raptor config
2018-11-10 19:42:46 -06:00
6093df11dc
Allow G26 to use the active extruder ( #12387 )
...
* Make lcd_quick_feedback argument optional
* Add click_to_cancel option to wait_for_hotend/bed
* Have G26 use the active nozzle and wait_for_hotend/bed
* Use wait_for_release in UBL G29
* Add 'T' parameter to G26 for an initial tool-change
2018-11-10 18:07:38 -06:00
4260282df7
Tevo Little Monster example configuration ( #12370 )
2018-11-10 03:36:01 -06:00
bed15fcd81
Tweak 'echo_not_entered' used by MBL's G29
2018-11-10 01:32:51 -06:00
c239131ff5
Use 'serial_spaces' in 'print_2d_array'
2018-11-10 01:32:51 -06:00
56150ec030
Add reference comments to MeshLevelingState
2018-11-09 21:31:20 -06:00
