Scott Lahteine
d5b7c595ae
Use static locals in utf_mapper.h
2015-11-12 00:03:21 -06:00
Scott Lahteine
9bdab4f3a8
Clean up "else" and other spacing
2015-11-12 00:03:21 -06:00
Scott Lahteine
9b23490f01
Clean up spacing in configs
2015-11-12 00:03:21 -06:00
esenapaj
c6c37abd41
Update language_kana.h
2015-11-12 00:00:51 -06:00
esenapaj
c24045475a
Update language_kana_utf8.h
2015-11-12 00:00:32 -06:00
Richard Wackerbarth
25d636c9e0
Compiler issues (PR#2696)
2015-11-11 23:52:11 -06:00
AnHardt
47401ec97b
MSG_EXTRUDER_SWITCHED_OFF was renamed to MSG_REDUNDANCY
...
in language.h, but was not renamed here. If TEMP_SENSOR_1 is enabled as redundant then
an error is thrown that MSG_EXTRUDER_SWITCHED_OFF is not defined.
Originaly by @12dstring
2015-10-08 10:45:11 -05:00
Scott Lahteine
ba6a243197
DEBUG message has no parameter (PR#2671)
2015-10-03 22:03:03 -05:00
Scott Lahteine
0c7f7ebcfb
Styling adjustments (PR#2668 & PR#2670)
...
Keep "astyled" reformatting
2015-10-03 22:02:45 -05:00
Rafa Couto
b5fb7075b9
Galician (gl) language.
2015-09-30 14:46:01 -05:00
Richard Wackerbarth
7b4bdc0203
DUAL_X_CARRIAGE motor enabling
...
As noted by @darkjavi et.al. in #103 , the E1 motor was not being enabled in planner.cpp when using DUAL_X_CARRIAGE. This patch enables and disables E1 as it should.
2015-09-30 04:31:19 -05:00
Richard Wackerbarth
91b5156b3e
Marlin 1.1.0 Release Candidate 2 - 29 September 2015
2015-09-29 20:28:41 -05:00
Richard Wackerbarth
03f0edb57e
Fix high LCD status screen update frequency (PR#2655)
2015-09-28 11:07:33 -05:00
KiteLab
0ad25c6665
Hint for changed behaviour of SDSUPPORT
2015-09-28 11:07:33 -05:00
Richard Wackerbarth
e01f5e1ef7
Cleanup
2015-09-17 10:44:23 -05:00
Mike Cochrane
5e36b64635
SDEXTRASLOW for some SD card readers (PR#176)
...
Add SDEXTRASLOW which runs the SD card at SPI_QUARTER_SPEED. Quarter speed is needed for RIGIDBOT_PANEL
2015-09-14 07:58:08 -05:00
Scott Lahteine
5d65a36dee
Give lcd_sd_status an UNKNOWN state (PR#180)
2015-09-14 06:32:27 -05:00
fmalpartida
0f149ea0c6
LCD home button causes repeated homing (PR#175)
...
Fix: increased debounce delay.
2015-09-14 06:31:49 -05:00
Scott Lahteine
b825567e0f
Drop www. from marlinfirmware.org (PR#175)
2015-09-14 06:28:53 -05:00
Scott Lahteine
db27e67580
Apply PID_ADD_EXTRUSION_RATE to extras
2015-09-12 07:53:20 -05:00
Scott Lahteine
bc50db9cf6
Implement PID_ADD_EXTRUSION_RATE
2015-09-12 07:53:20 -05:00
Scott Lahteine
cffb2d457e
Cleanup file formatting
2015-09-12 07:48:27 -05:00
Scott Lahteine
7ac7ddbf20
Show nozzles, heaters, and extruders numbered 1-4
2015-09-12 07:40:18 -05:00
Scott Lahteine
5bc480fee8
Fix Move E menu items
2015-09-12 07:33:49 -05:00
Scott Lahteine
fc882c34a3
Init lcd_sd_status as false to force lcd_update test
...
Replaces #145 which is way out of date
2015-09-12 07:32:20 -05:00
Scott Lahteine
e27dd5c22d
Conditionalize functions that rely on SDSUPPORT
2015-09-12 07:30:09 -05:00
Scott Lahteine
fabf3ae4a0
Add final Z raise after Delta probe
2015-09-12 07:23:24 -05:00
Petr Zahradnik
8c768a76a2
Create language_cz.h
...
Czech language translation.
2015-09-12 07:18:05 -05:00
Petr Zahradnik
5b9010965d
Update language.h
...
Added comment for Czech language (associated with file language_cz.h).
2015-09-11 04:43:54 +02:00
Scott Lahteine
89fb778684
Fix up probe pin define and test
2015-09-10 10:54:03 -05:00
Scott Lahteine
558665cd90
Constrain Tune > Nozzle/Flow menu items
2015-09-10 08:47:11 -05:00
Scott Lahteine
9f462f0cf5
Hack to address stuttering caused by ISR not finishing in time
...
(PR #138 )
When the ISR does not finish in time, the timer will
wrap in the computation of the next interrupt time.
This hack replaces the correct (past) time with a time not far in the future.
2015-09-10 08:26:17 -05:00
Scott Lahteine
8b3d63c423
Unify Delta XYZ homing rates
...
As noted in #130 allen key probe stow rate is based on homing rates,
but homing rates were left out of most delta configs. This unifies the
XYZ homing rates and applies the unified rates to allen key movements.
2015-09-08 13:11:55 -05:00
Scott Lahteine
7c72b57313
Unify manual feedrate and Fix LCD MANUAL_FEEDRATE (PR#128)
...
As noted by @o-lampe at https://github.com/MarlinFirmware/MarlinDev/issues/114#issuecomment-136757614 the `MANUAL_FEEDRATE` for Delta Z should be the same as XY.
2015-09-08 13:11:55 -05:00
Scott Lahteine
f690b82343
Remove extra MAX_FREQ_TIME define (PR#148)
2015-09-08 13:11:12 -05:00
Scott Lahteine
a4c78ae786
Add E1 pins to SENSITIVE_PINS for Dual Y or Dual Z
2015-09-07 09:41:06 -05:00
Scott Lahteine
a39fadf876
Update kossel-pro example config (again?)
2015-09-07 09:41:06 -05:00
Scott Lahteine
34e0a8d848
Move Y2 and Z2 pins defines to pins.h
2015-09-07 09:41:06 -05:00
Scott Lahteine
28599c51c7
Wrap Dual Y options in a conditional
2015-09-07 09:41:05 -05:00
Scott Lahteine
11a065c0ca
Remove Z2 pins overrides from Configuration_adv.h
2015-09-07 09:41:05 -05:00
Scott Lahteine
f7f6b5faae
Fix lcd_move_e compile error (PR#143)
...
Fix a compile error introduced in #98
2015-09-07 09:36:05 -05:00
Scott Lahteine
2b30e8ac99
Conditionals for ULTIPANEL without SDSUPPORT
2015-09-06 02:04:49 -05:00
Scott Lahteine
7c7a4051fe
Disable SDSUPPORT by default
...
As noted in #133 you can’t disable `SDSUPPORT` with `MAKRPANEL`,
`PANEL_ONE`, `MINIPANEL`, or `ULTIPANEL`. This patch makes it possible
to disable `SDSUPPORT` on these controllers and then disables it by
default.
Users of these controllers will now need to enable `SDSUPPORT` in their
configurations as others currently do.
2015-09-06 02:04:49 -05:00
Eric Kuzmenko
b23d765991
Added Extrude From Multiple Extruders from LCD feature
2015-09-05 05:33:18 -05:00
Christian Lefrançois
8347a9d6e4
Fix HOMING_BUMP_DIVISOR for deltas configuration
...
* Re-bump speed divisor should be the same for delta printer.
2015-09-03 09:26:28 -05:00
Scott Lahteine
703df2cb6c
Fix error message for probe region sanity check
2015-09-03 03:27:47 -05:00
Shane Francis
4c8330c15c
Trim Adjustments for Delta Configurations
2015-09-03 01:05:33 -05:00
Scott Lahteine
962120d1d2
Fix spacing in some conditional blocks
2015-08-27 20:59:09 -05:00
Richard Wackerbarth
20b4772155
Create DEBUG_LEVELING_FEATURE
2015-08-27 20:52:08 -05:00
Scott Lahteine
194f98ff95
Debug messages for homing and leveling
2015-08-27 20:52:08 -05:00
