Merge pull request #6768 from thinkyhead/rc_spindle_m3_m5
Spindle / Laser support
This commit is contained in:
Scott Lahteine
GitHub
commit
e806e6419a
@ -579,7 +579,7 @@
|
||||
#define HAS_SUICIDE (PIN_EXISTS(SUICIDE))
|
||||
#define HAS_PHOTOGRAPH (PIN_EXISTS(PHOTOGRAPH))
|
||||
#define HAS_BUZZER (PIN_EXISTS(BEEPER) || ENABLED(LCD_USE_I2C_BUZZER))
|
||||
#define HAS_CASE_LIGHT (PIN_EXISTS(CASE_LIGHT))
|
||||
#define HAS_CASE_LIGHT (PIN_EXISTS(CASE_LIGHT) && ENABLED(CASE_LIGHT_ENABLE))
|
||||
|
||||
// Digital control
|
||||
#define HAS_MICROSTEPS (HAS_X_MICROSTEPS || HAS_Y_MICROSTEPS || HAS_Z_MICROSTEPS || HAS_E0_MICROSTEPS || HAS_E1_MICROSTEPS || HAS_E2_MICROSTEPS || HAS_E3_MICROSTEPS || HAS_E4_MICROSTEPS)
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1132,6 +1132,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -73,6 +73,9 @@
|
||||
*
|
||||
* M0 - Unconditional stop - Wait for user to press a button on the LCD (Only if ULTRA_LCD is enabled)
|
||||
* M1 - Same as M0
|
||||
* M3 - Turn laser/spindle on, set spindle/laser speed/power, set rotation to clockwise
|
||||
* M4 - Turn laser/spindle on, set spindle/laser speed/power, set rotation to counter-clockwise
|
||||
* M5 - Turn laser/spindle off
|
||||
* M17 - Enable/Power all stepper motors
|
||||
* M18 - Disable all stepper motors; same as M84
|
||||
* M20 - List SD card. (Requires SDSUPPORT)
|
||||
@ -5611,6 +5614,121 @@ inline void gcode_G92() {
|
||||
|
||||
#endif // HAS_RESUME_CONTINUE
|
||||
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
/**
|
||||
* M3: Spindle Clockwise
|
||||
* M4: Spindle Counter-clockwise
|
||||
*
|
||||
* S0 turns off spindle.
|
||||
*
|
||||
* If no speed PWM output is defined then M3/M4 just turns it on.
|
||||
*
|
||||
* At least 12.8KHz (50Hz * 256) is needed for spindle PWM.
|
||||
* Hardware PWM is required. ISRs are too slow.
|
||||
*
|
||||
* NOTE: WGM for timers 3, 4, and 5 must be either Mode 1 or Mode 5.
|
||||
* No other settings give a PWM signal that goes from 0 to 5 volts.
|
||||
*
|
||||
* The system automatically sets WGM to Mode 1, so no special
|
||||
* initialization is needed.
|
||||
*
|
||||
* WGM bits for timer 2 are automatically set by the system to
|
||||
* Mode 1. This produces an acceptable 0 to 5 volt signal.
|
||||
* No special initialization is needed.
|
||||
*
|
||||
* NOTE: A minimum PWM frequency of 50 Hz is needed. All prescaler
|
||||
* factors for timers 2, 3, 4, and 5 are acceptable.
|
||||
*
|
||||
* SPINDLE_LASER_ENABLE_PIN needs an external pullup or it may power on
|
||||
* the spindle/laser during power-up or when connecting to the host
|
||||
* (usually goes through a reset which sets all I/O pins to tri-state)
|
||||
*
|
||||
* PWM duty cycle goes from 0 (off) to 255 (always on).
|
||||
*/
|
||||
|
||||
// Wait for spindle to come up to speed
|
||||
inline void delay_for_power_up() {
|
||||
refresh_cmd_timeout();
|
||||
while (PENDING(millis(), SPINDLE_LASER_POWERUP_DELAY + previous_cmd_ms)) idle();
|
||||
}
|
||||
|
||||
// Wait for spindle to stop turning
|
||||
inline void delay_for_power_down() {
|
||||
refresh_cmd_timeout();
|
||||
while (PENDING(millis(), SPINDLE_LASER_POWERDOWN_DELAY + previous_cmd_ms + 1)) idle();
|
||||
}
|
||||
|
||||
/**
|
||||
* ocr_val_mode() is used for debugging and to get the points needed to compute the RPM vs ocr_val line
|
||||
*
|
||||
* it accepts inputs of 0-255
|
||||
*/
|
||||
|
||||
inline void ocr_val_mode() {
|
||||
uint8_t spindle_laser_power = code_value_byte();
|
||||
WRITE(SPINDLE_LASER_ENABLE_PIN, SPINDLE_LASER_ENABLE_INVERT); // turn spindle on (active low)
|
||||
if (SPINDLE_LASER_PWM_INVERT) spindle_laser_power = 255 - spindle_laser_power;
|
||||
analogWrite(SPINDLE_LASER_PWM_PIN, spindle_laser_power);
|
||||
}
|
||||
|
||||
inline void gcode_M3_M4(bool is_M3) {
|
||||
|
||||
stepper.synchronize(); // wait until previous movement commands (G0/G0/G2/G3) have completed before playing with the spindle
|
||||
#if SPINDLE_DIR_CHANGE
|
||||
const bool rotation_dir = (is_M3 && !SPINDLE_INVERT_DIR || !is_M3 && SPINDLE_INVERT_DIR) ? HIGH : LOW;
|
||||
if (SPINDLE_STOP_ON_DIR_CHANGE \
|
||||
&& READ(SPINDLE_LASER_ENABLE_PIN) == SPINDLE_LASER_ENABLE_INVERT \
|
||||
&& READ(SPINDLE_DIR_PIN) != rotation_dir
|
||||
) {
|
||||
WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT); // turn spindle off
|
||||
delay_for_power_down();
|
||||
}
|
||||
digitalWrite(SPINDLE_DIR_PIN, rotation_dir);
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Our final value for ocr_val is an unsigned 8 bit value between 0 and 255 which usually means uint8_t.
|
||||
* Went to uint16_t because some of the uint8_t calculations would sometimes give 1000 0000 rather than 1111 1111.
|
||||
* Then needed to AND the uint16_t result with 0x00FF to make sure we only wrote the byte of interest.
|
||||
*/
|
||||
#if ENABLED(SPINDLE_LASER_PWM)
|
||||
if (code_seen('O')) ocr_val_mode();
|
||||
else {
|
||||
const float spindle_laser_power = code_seen('S') ? code_value_float() : 0;
|
||||
if (spindle_laser_power == 0) {
|
||||
WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT); // turn spindle off (active low)
|
||||
delay_for_power_down();
|
||||
}
|
||||
else {
|
||||
int16_t ocr_val = (spindle_laser_power - (SPEED_POWER_INTERCEPT)) * (1.0 / (SPEED_POWER_SLOPE)); // convert RPM to PWM duty cycle
|
||||
NOMORE(ocr_val, 255); // limit to max the Atmel PWM will support
|
||||
if (spindle_laser_power <= SPEED_POWER_MIN)
|
||||
ocr_val = (SPEED_POWER_MIN - (SPEED_POWER_INTERCEPT)) * (1.0 / (SPEED_POWER_SLOPE)); // minimum setting
|
||||
if (spindle_laser_power >= SPEED_POWER_MAX)
|
||||
ocr_val = (SPEED_POWER_MAX - (SPEED_POWER_INTERCEPT)) * (1.0 / (SPEED_POWER_SLOPE)); // limit to max RPM
|
||||
if (SPINDLE_LASER_PWM_INVERT) ocr_val = 255 - ocr_val;
|
||||
WRITE(SPINDLE_LASER_ENABLE_PIN, SPINDLE_LASER_ENABLE_INVERT); // turn spindle on (active low)
|
||||
analogWrite(SPINDLE_LASER_PWM_PIN, ocr_val & 0xFF); // only write low byte
|
||||
delay_for_power_up();
|
||||
}
|
||||
}
|
||||
#else
|
||||
WRITE(SPINDLE_LASER_ENABLE_PIN, SPINDLE_LASER_ENABLE_INVERT); // turn spindle on (active low) if spindle speed option not enabled
|
||||
delay_for_power_up();
|
||||
#endif
|
||||
}
|
||||
|
||||
/**
|
||||
* M5 turn off spindle
|
||||
*/
|
||||
inline void gcode_M5() {
|
||||
stepper.synchronize();
|
||||
WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT);
|
||||
delay_for_power_down();
|
||||
}
|
||||
|
||||
#endif // SPINDLE_LASER_ENABLE
|
||||
|
||||
/**
|
||||
* M17: Enable power on all stepper motors
|
||||
*/
|
||||
@ -5626,6 +5744,7 @@ inline void gcode_M17() {
|
||||
#endif
|
||||
|
||||
#if ENABLED(PARK_HEAD_ON_PAUSE)
|
||||
|
||||
float resume_position[XYZE];
|
||||
bool move_away_flag = false;
|
||||
|
||||
@ -9946,6 +10065,17 @@ void process_next_command() {
|
||||
break;
|
||||
#endif // ULTIPANEL
|
||||
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
case 3:
|
||||
gcode_M3_M4(true); // M3: turn spindle/laser on, set laser/spindle power/speed, set rotation direction CW
|
||||
break; // synchronizes with movement commands
|
||||
case 4:
|
||||
gcode_M3_M4(false); // M4: turn spindle/laser on, set laser/spindle power/speed, set rotation direction CCW
|
||||
break; // synchronizes with movement commands
|
||||
case 5:
|
||||
gcode_M5(); // M5 - turn spindle/laser off
|
||||
break; // synchronizes with movement commands
|
||||
#endif
|
||||
case 17: // M17: Enable all stepper motors
|
||||
gcode_M17();
|
||||
break;
|
||||
@ -12262,6 +12392,17 @@ void setup() {
|
||||
update_case_light();
|
||||
#endif
|
||||
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
OUT_WRITE(SPINDLE_LASER_ENABLE_PIN, !SPINDLE_LASER_ENABLE_INVERT); // init spindle to off
|
||||
#if SPINDLE_DIR_CHANGE
|
||||
OUT_WRITE(SPINDLE_DIR_PIN, SPINDLE_INVERT_DIR ? 255 : 0); // init rotation to clockwise (M3)
|
||||
#endif
|
||||
#if ENABLED(SPINDLE_LASER_PWM)
|
||||
SET_OUTPUT(SPINDLE_LASER_PWM_PIN);
|
||||
analogWrite(SPINDLE_LASER_PWM_PIN, SPINDLE_LASER_PWM_INVERT ? 255 : 0); // set to lowest speed
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if HAS_BED_PROBE
|
||||
endstops.enable_z_probe(false);
|
||||
#endif
|
||||
|
||||
@ -1134,3 +1134,64 @@ static_assert(COUNT(sanity_arr_3) >= XYZE, "DEFAULT_MAX_ACCELERATION requires 4
|
||||
static_assert(COUNT(sanity_arr_1) <= XYZE_N, "DEFAULT_AXIS_STEPS_PER_UNIT has too many elements.");
|
||||
static_assert(COUNT(sanity_arr_2) <= XYZE_N, "DEFAULT_MAX_FEEDRATE has too many elements.");
|
||||
static_assert(COUNT(sanity_arr_3) <= XYZE_N, "DEFAULT_MAX_ACCELERATION has too many elements.");
|
||||
|
||||
/**
|
||||
* Sanity checks for Spindle / Laser
|
||||
*/
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
#if !PIN_EXISTS(SPINDLE_LASER_ENABLE)
|
||||
#error "SPINDLE_LASER_ENABLE requires SPINDLE_LASER_ENABLE_PIN."
|
||||
#elif SPINDLE_DIR_CHANGE && !PIN_EXISTS(SPINDLE_DIR)
|
||||
#error "SPINDLE_DIR_PIN not defined."
|
||||
#elif ENABLED(SPINDLE_LASER_PWM) && PIN_EXISTS(SPINDLE_LASER_PWM)
|
||||
#if !(WITHIN(SPINDLE_LASER_PWM_PIN, 2, 13) || WITHIN(SPINDLE_LASER_PWM_PIN, 44, 46))
|
||||
#error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin."
|
||||
#elif SPINDLE_LASER_POWERUP_DELAY < 1
|
||||
#error "SPINDLE_LASER_POWERUP_DELAY must be greater than 0."
|
||||
#elif SPINDLE_LASER_POWERDOWN_DELAY < 1
|
||||
#error "SPINDLE_LASER_POWERDOWN_DELAY must be greater than 0."
|
||||
#elif !defined(SPINDLE_LASER_PWM_INVERT)
|
||||
#error "SPINDLE_LASER_PWM_INVERT missing."
|
||||
#elif !defined(SPEED_POWER_SLOPE) || !defined(SPEED_POWER_INTERCEPT) || !defined(SPEED_POWER_MIN) || !defined(SPEED_POWER_MAX)
|
||||
#error "SPINDLE_LASER_PWM equation constant(s) missing."
|
||||
#elif SPINDLE_LASER_PWM_PIN == 4 || WITHIN(SPINDLE_LASER_PWM_PIN, 11, 13)
|
||||
#error "Counter/Timer for SPINDLE_LASER_PWM_PIN is used by a system interrupt."
|
||||
#elif PIN_EXISTS(X_MAX) && X_MAX_PIN == SPINDLE_LASER_PWM_PIN
|
||||
#error "SPINDLE_LASER_PWM pin is in use by X_MAX endstop."
|
||||
#elif PIN_EXISTS(X_MIN) && X_MIN_PIN == SPINDLE_LASER_PWM_PIN
|
||||
#error "SPINDLE_LASER_PWM pin is in use by X_MIN endstop."
|
||||
#elif PIN_EXISTS(Z_STEP) && Z_STEP_PIN == SPINDLE_LASER_PWM_PIN
|
||||
#error "SPINDLE_LASER_PWM pin in use by Z_STEP."
|
||||
#elif NUM_SERVOS > 0 && (WITHIN(SPINDLE_LASER_PWM_PIN, 2, 3) || SPINDLE_LASER_PWM_PIN == 5)
|
||||
#error "Counter/Timer for SPINDLE_LASER_PWM_PIN is used by the servo system."
|
||||
#elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT_PIN."
|
||||
#elif PIN_EXISTS(E0_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E0_AUTO_FAN_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by E0_AUTO_FAN_PIN."
|
||||
#elif PIN_EXISTS(E1_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E1_AUTO_FAN_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by E1_AUTO_FAN_PIN."
|
||||
#elif PIN_EXISTS(E2_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E2_AUTO_FAN_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by E2_AUTO_FAN_PIN."
|
||||
#elif PIN_EXISTS(E3_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E3_AUTO_FAN_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
|
||||
#elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
|
||||
#elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used FAN_PIN."
|
||||
#elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used FAN1_PIN."
|
||||
#elif PIN_EXISTS(FAN2) && SPINDLE_LASER_PWM_PIN == FAN2_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used FAN2_PIN."
|
||||
#elif PIN_EXISTS(CONTROLLERFAN) && SPINDLE_LASER_PWM_PIN == CONTROLLERFAN_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by CONTROLLERFAN_PIN."
|
||||
#elif PIN_EXISTS(MOTOR_CURRENT_PWM_XY) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_XY_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_XY."
|
||||
#elif PIN_EXISTS(MOTOR_CURRENT_PWM_Z) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_Z_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_Z."
|
||||
#elif PIN_EXISTS(MOTOR_CURRENT_PWM_E) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_E_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_E."
|
||||
#elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
|
||||
#error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT."
|
||||
#endif
|
||||
#endif
|
||||
#endif // SPINDLE_LASER_ENABLE
|
||||
|
||||
@ -130,6 +130,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 3
|
||||
@ -173,6 +175,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 2
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1132,11 +1132,64 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
// @section debug
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
#define PINS_DEBUGGING
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Auto-report temperatures with M155 S<seconds>
|
||||
*/
|
||||
|
||||
@ -132,6 +132,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -175,6 +177,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
#define MACHINE_UUID "8d083632-40c5-4649-85b8-43d9ae6c5d55" // BQ Hephestos 2 standard config
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1109,6 +1109,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -149,6 +149,8 @@
|
||||
#define MACHINE_UUID "92f72de1-c211-452e-9f2b-61ef88a4751e" // K8200 standard config without VM8201 (Display)
|
||||
#endif
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -192,6 +194,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1138,6 +1138,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 2
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -132,6 +132,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1 // Single extruder. Set to 2 for dual extruders
|
||||
@ -175,6 +177,8 @@
|
||||
#define HOTEND_OFFSET_X {0.0, 36.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
#define HOTEND_OFFSET_Y {0.0, 0.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -162,6 +162,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -205,6 +207,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -151,6 +151,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -194,6 +196,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1128,6 +1128,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -132,6 +132,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -175,6 +177,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1130,6 +1130,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1129,6 +1129,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1127,6 +1127,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1127,6 +1127,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -133,6 +133,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -176,6 +178,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1132,6 +1132,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1127,6 +1127,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -134,6 +134,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -177,6 +179,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1132,6 +1132,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1125,6 +1125,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -129,6 +129,8 @@
|
||||
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
||||
//#define MACHINE_UUID "5f0bb7a3-0e14-428c-812b-15ab0d3ecc71"
|
||||
|
||||
// @section extruder
|
||||
|
||||
// This defines the number of extruders
|
||||
// :[1, 2, 3, 4, 5]
|
||||
#define EXTRUDERS 1
|
||||
@ -172,6 +174,8 @@
|
||||
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
* Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
|
||||
*
|
||||
|
||||
@ -1128,6 +1128,55 @@
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave
|
||||
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
* Spindle & Laser control
|
||||
*
|
||||
* Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and
|
||||
* to set spindle speed, spindle direction, and laser power.
|
||||
*
|
||||
* SuperPid is a router/spindle speed controller used in the CNC milling community.
|
||||
* Marlin can be used to turn the spindle on and off. It can also be used to set
|
||||
* the spindle speed from 5,000 to 30,000 RPM.
|
||||
*
|
||||
* You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V
|
||||
* hardware PWM pin for the speed control and a pin for the rotation direction.
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // set to true if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // delay in milliseconds to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // delay in milliseconds to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
|
||||
@ -515,8 +515,8 @@
|
||||
#if PIN_EXISTS(SPINDLE_LASER_ENABLE)
|
||||
REPORT_NAME_DIGITAL(SPINDLE_LASER_ENABLE_PIN, __LINE__ )
|
||||
#endif
|
||||
#if PIN_EXISTS(SPINDLE_SPEED_LASER_POWER)
|
||||
REPORT_NAME_DIGITAL(SPINDLE_SPEED_LASER_POWER_PIN, __LINE__ )
|
||||
#if PIN_EXISTS(SPINDLE_LASER_PWM)
|
||||
REPORT_NAME_DIGITAL(SPINDLE_LASER_PWM_PIN, __LINE__ )
|
||||
#endif
|
||||
#if PIN_EXISTS(SR_CLK)
|
||||
REPORT_NAME_DIGITAL(SR_CLK_PIN, __LINE__ )
|
||||
|
||||
@ -43,6 +43,8 @@
|
||||
#define RAMPS_D9_PIN 8
|
||||
#define MOSFET_D_PIN 12
|
||||
|
||||
#define CASE_LIGHT_PIN -1 // MUST BE HARDWARE PWM but one is not available on expansion header
|
||||
|
||||
#include "pins_RAMPS.h"
|
||||
|
||||
//
|
||||
@ -104,3 +106,58 @@
|
||||
#define BEEPER_PIN 33
|
||||
|
||||
#endif // ULTRA_LCD && NEWPANEL
|
||||
|
||||
/**
|
||||
* M3/M4/M5 - Spindle/Laser Control
|
||||
*
|
||||
* If you want to control the speed of your spindle then you'll have
|
||||
* have to sacrifce the Extruder and pull some signals off the Z stepper
|
||||
* driver socket.
|
||||
*
|
||||
* The following assumes:
|
||||
* - the Z stepper driver socket is empty
|
||||
* - the extruder driver socket has a driver board plugged into it
|
||||
* - the Z stepper wires are attached the the extruder connector
|
||||
*
|
||||
* If you want to keep the extruder AND don't have a LCD display then
|
||||
* you can still control the power on/off and spindle direction.
|
||||
*
|
||||
* Where to get spindle signals
|
||||
*
|
||||
* stepper signal socket name socket name
|
||||
* -------
|
||||
* SPINDLE_LASER_ENABLE_PIN /ENABLE O| |O VMOT
|
||||
* MS1 O| |O GND
|
||||
* MS2 O| |O 2B
|
||||
* MS3 O| |O 2A
|
||||
* /RESET O| |O 1A
|
||||
* /SLEEP O| |O 1B
|
||||
* SPINDLE_LASER_PWM_PIN STEP O| |O VDD
|
||||
* SPINDLE_DIR_PIN DIR O| |O GND
|
||||
* -------
|
||||
*
|
||||
* Note: Socket names vary from vendor to vendor
|
||||
*/
|
||||
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not good with 3DRAG
|
||||
#undef SPINDLE_LASER_ENABLE_PIN
|
||||
#undef SPINDLE_DIR_PIN
|
||||
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
#if !EXTRUDERS
|
||||
#undef E0_DIR_PIN
|
||||
#undef E0_ENABLE_PIN
|
||||
#undef E0_STEP_PIN
|
||||
#undef Z_DIR_PIN
|
||||
#undef Z_ENABLE_PIN
|
||||
#undef Z_STEP_PIN
|
||||
#define Z_DIR_PIN 28
|
||||
#define Z_ENABLE_PIN 24
|
||||
#define Z_STEP_PIN 26
|
||||
#define SPINDLE_LASER_PWM_PIN 46 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 62 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 48
|
||||
#elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // use expansion header if no LCD in use
|
||||
#define SPINDLE_LASER_ENABLE_PIN 16 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_DIR_PIN 17
|
||||
#endif
|
||||
#endif
|
||||
|
||||
@ -24,12 +24,20 @@
|
||||
* AZTEEG_X3 Arduino Mega with RAMPS v1.4 pin assignments
|
||||
*/
|
||||
|
||||
#ifndef __AVR_ATmega2560__
|
||||
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#if HOTENDS > 2 || E_STEPPERS > 2
|
||||
#error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue."
|
||||
#endif
|
||||
|
||||
#define BOARD_NAME "Azteeg X3"
|
||||
|
||||
#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming
|
||||
#define OK_TO_CHANGE_CASE_LIGHT // in from from the include file
|
||||
#endif
|
||||
|
||||
#include "pins_RAMPS_13.h"
|
||||
|
||||
//
|
||||
@ -63,3 +71,30 @@
|
||||
#define STAT_LED_BLUE_PIN 11
|
||||
|
||||
#endif
|
||||
|
||||
//
|
||||
// Misc
|
||||
//
|
||||
#if ENABLED(OK_TO_CHANGE_CASE_LIGHT) && STAT_LED_RED_PIN == 6
|
||||
#undef STAT_LED_RED_PIN
|
||||
#undef CASE_LIGHT_PIN
|
||||
#define CASE_LIGHT_PIN 6 // open collector FET driver
|
||||
#endif
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
|
||||
#undef SPINDLE_LASER_ENABLE_PIN
|
||||
#undef SPINDLE_DIR_PIN
|
||||
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
#undef SDA // use EXP3 header
|
||||
#undef SCL
|
||||
#if SERVO0_PIN == 7
|
||||
#undef SERVO0_PIN
|
||||
#def SERVO0_PIN 11
|
||||
#define SPINDLE_LASER_PWM_PIN 7 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 21
|
||||
#endif
|
||||
|
||||
@ -30,8 +30,16 @@
|
||||
|
||||
#define BOARD_NAME "Azteeg X3 Pro"
|
||||
|
||||
#if !PIN_EXISTS(CASE_LIGHT) // doesn't already exist so OK to change the definition coming
|
||||
#define OK_TO_CHANGE_CASE_LIGHT // in from from the include file
|
||||
#endif
|
||||
|
||||
#include "pins_RAMPS.h"
|
||||
|
||||
#ifndef __AVR_ATmega2560__
|
||||
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
//
|
||||
// Servos
|
||||
//
|
||||
@ -126,7 +134,37 @@
|
||||
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
|
||||
#undef SD_DETECT_PIN
|
||||
#define SD_DETECT_PIN 49 // For easy adapter board
|
||||
#undef BEEPER_PIN
|
||||
#define BEEPER_PIN 12 // 33 isn't physically available to the LCD display
|
||||
#else
|
||||
#define STAT_LED_RED_PIN 32
|
||||
#define STAT_LED_BLUE_PIN 35
|
||||
#endif
|
||||
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
#undef DOGLCD_A0 // steal pin 44 for the case light
|
||||
#define DOGLCD_A0 57
|
||||
#if ENABLED(OK_TO_CHANGE_CASE_LIGHT)
|
||||
#undef CASE_LIGHT_PIN
|
||||
#define CASE_LIGHT_PIN 44 // must have a hardware PWM
|
||||
#endif
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3 board
|
||||
#undef SPINDLE_LASER_ENABLE_PIN
|
||||
#undef SPINDLE_DIR_PIN
|
||||
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE) // use EXP2 header
|
||||
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
|
||||
#undef BTN_EN2
|
||||
#define BTN_EN2 31 // need 7 for the spindle speed PWM
|
||||
#endif
|
||||
#define SPINDLE_LASER_PWM_PIN 7 // must have a hardware PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 21
|
||||
#endif
|
||||
|
||||
|
||||
@ -30,6 +30,13 @@
|
||||
|
||||
#define BOARD_NAME "2PrintBeta Due"
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 66 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_DIR_PIN 67
|
||||
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
|
||||
|
||||
#include "pins_RAMPS.h"
|
||||
|
||||
//
|
||||
|
||||
@ -46,6 +46,18 @@
|
||||
#define ORIG_E2_AUTO_FAN_PIN 6
|
||||
#define ORIG_E3_AUTO_FAN_PIN 6
|
||||
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
#define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 42
|
||||
|
||||
#include "pins_RAMPS_13.h"
|
||||
|
||||
//
|
||||
|
||||
@ -27,6 +27,40 @@
|
||||
* https://github.com/unrepentantgeek/brainwave-arduino
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 16 JAN 2017
|
||||
*
|
||||
* Added pointer to a currently available Arduino IDE extension that will
|
||||
* allow this board to use the latest Marlin software
|
||||
*/
|
||||
|
||||
/**
|
||||
* Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB
|
||||
* This is the only known IDE extension that is compatible with the pin definitions
|
||||
* in this file, Adrduino 1.6.12 and the latest mainstream Marlin software.
|
||||
*
|
||||
* "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share
|
||||
* the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such
|
||||
* that PWM1A, PWM1B & PWM1C can not be used.
|
||||
*
|
||||
* Installation:
|
||||
*
|
||||
* 1. In the Arduino IDE, under Files -> Preferences paste the following URL
|
||||
* https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json
|
||||
* 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB
|
||||
* and then click on "Install"
|
||||
* 3. Select "AT90USB646_STANDARD" from the 'Tools -> Boards' menu.
|
||||
*/
|
||||
|
||||
/**
|
||||
* To burn the bootloader that comes with Marlin_AT90USB:
|
||||
*
|
||||
* 1. Connect your programmer to the board.
|
||||
* 2. In Arduino IDE select "AT90USB646_STANDARD" and then select the programmer.
|
||||
* 3. In Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
|
||||
* 4. The programmer is no longer needed. Remove it.
|
||||
*/
|
||||
|
||||
#ifndef __AVR_AT90USB646__
|
||||
#error "Oops! Make sure you have 'Brainwave' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
@ -27,14 +27,70 @@
|
||||
* https://github.com/unrepentantgeek/brainwave-arduino
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 16 JAN 2017
|
||||
*
|
||||
* Added pointers to currently available Arduino IDE extensions that will
|
||||
* allow this board to use the latest Marlin software
|
||||
*/
|
||||
|
||||
/**
|
||||
* There are three Arduino IDE extensions that are compatible with this board
|
||||
* and with the mainstream Marlin software. All have been used with Arduino 1.6.12
|
||||
*
|
||||
* Teensyduino - http://www.pjrc.com/teensy/teensyduino.html
|
||||
* Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu
|
||||
*
|
||||
* Installation instructions are at the above URL. Don't bother loading the
|
||||
* libraries - they are not used with the Marlin software.
|
||||
*
|
||||
* Printrboard - https://github.com/scwimbush/Printrboard-HID-Arduino-IDE-Support
|
||||
* This is basically Teensyduino but with a bootloader that can handle image sizes
|
||||
* larger than 64K.
|
||||
*
|
||||
* Installation:
|
||||
*
|
||||
* 1. Go to the above URL, click on the "Clone or Download" button and then
|
||||
* click on "Download ZIP" button.
|
||||
* 2. Unzip the file, find the "printrboard" directory and then copy it to the
|
||||
* hardware directory in Arduino. The Arduino hardware directory will probably
|
||||
* be located in a path similar to this: C:\Program Files (x86)\Arduino\hardware.
|
||||
* 3. Restart Arduino.
|
||||
* 4. Select "Printrboard" from the 'Tools -> Boards' menu.
|
||||
*
|
||||
* Marlin_AT90USB - https://github.com/Bob-the-Kuhn/Marlin_AT90USB
|
||||
* Uses the bootloader from Printerboard above.
|
||||
*
|
||||
* "Marlin_AT90USB" makes PWM0A available rather than the usual PWM1C. These PWMs share
|
||||
* the same physical pin. Marlin uses TIMER1 to generate interrupts and sets it up such
|
||||
* that PWM1A, PWM1B & PWM1C can not be used.
|
||||
*
|
||||
* Installation:
|
||||
*
|
||||
* 1. In the Arduino IDE, under Files -> Preferences paste the following URL
|
||||
* https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json
|
||||
* 2. Under Tools -> Board -> Boards manager, scroll to the bottom, click on MARLIN_AT90USB
|
||||
* and then click on "Install"
|
||||
* 3. Select "AT90USB1286_TEENSYPP" from the 'Tools -> Boards' menu.
|
||||
*/
|
||||
|
||||
/**
|
||||
* To burn the bootloader that comes with Printrboard and Marlin_AT90USB:
|
||||
*
|
||||
* 1. Connect your programmer to the board.
|
||||
* 2. In the Arduino IDE select "Printrboard" or "AT90USB1286_TEENSYPP" and then select the programmer.
|
||||
* 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message.
|
||||
* 4. The programmer is no longer needed. Remove it.
|
||||
*/
|
||||
|
||||
#ifndef __AVR_AT90USB1286__
|
||||
#error "Oops! Make sure you have 'Brainwave Pro' selected from the 'Tools -> Boards' menu."
|
||||
#error "Oops! Make sure you have 'Teensy++ 2.0', 'AT90USB1286_TEENSYPP', or 'Printrboard' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#include "fastio.h"
|
||||
|
||||
#if DISABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin alphabetical.
|
||||
#error "Uncomment #define AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h for this config"
|
||||
#error "Uncomment '#define AT90USBxx_TEENSYPP_ASSIGNMENTS' in fastio.h for this config"
|
||||
#endif
|
||||
|
||||
#define BOARD_NAME "Brainwave Pro"
|
||||
|
||||
@ -54,3 +54,10 @@
|
||||
#define SD_DETECT_PIN 6
|
||||
|
||||
#endif // NEWPANEL && ULTRA_LCD
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not valid with this board
|
||||
#undef SPINDLE_LASER_ENABLE_PIN
|
||||
#undef SPINDLE_DIR_PIN
|
||||
|
||||
@ -24,6 +24,31 @@
|
||||
* Gen3 Monolithic Electronics pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* added pointer to a current Arduino IDE extension
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef __AVR_ATmega644P__
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
@ -73,3 +98,4 @@
|
||||
#define PS_ON_PIN 14 // Alex, does this work on the card?
|
||||
|
||||
// Alex extras from Gen3+
|
||||
|
||||
|
||||
@ -24,6 +24,32 @@
|
||||
* Gen3+ pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* added pointer to a current Arduino IDE extension
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the SANGUINO board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
@ -73,4 +99,3 @@
|
||||
//
|
||||
#define SDSS 4
|
||||
#define PS_ON_PIN 14
|
||||
|
||||
|
||||
@ -24,6 +24,33 @@
|
||||
* Gen6 pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* 1) added pointer to a current Arduino IDE extension
|
||||
* 2) added support for M3, M4 & M5 spindle control commands
|
||||
* 3) added case light pin definition
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef __AVR_ATmega644P__
|
||||
#ifndef __AVR_ATmega1284P__
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
||||
@ -80,7 +107,15 @@
|
||||
//
|
||||
#define SDSS 17
|
||||
#define DEBUG_PIN 0
|
||||
#define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM
|
||||
|
||||
// RS485 pins
|
||||
#define TX_ENABLE_PIN 12
|
||||
#define RX_ENABLE_PIN 13
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 6
|
||||
|
||||
@ -24,6 +24,32 @@
|
||||
* Gen6 Deluxe pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* added pointer to a current Arduino IDE extension
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the SANGUINO board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
|
||||
#define BOARD_NAME "Gen6 Deluxe"
|
||||
|
||||
#include "pins_GEN6.h"
|
||||
|
||||
@ -24,8 +24,35 @@
|
||||
* Gen7 v1.1, v1.2, v1.3 pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* 1) added pointer to a current Arduino IDE extension
|
||||
* 2) added support for M3, M4 & M5 spindle control commands
|
||||
* 3) added case light pin definition
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
||||
#error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu."
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#ifndef BOARD_NAME
|
||||
@ -39,10 +66,13 @@
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#define X_STOP_PIN 7
|
||||
#define Y_STOP_PIN 5
|
||||
#define X_MIN_PIN 7
|
||||
#define Y_MIN_PIN 5
|
||||
#define Z_MIN_PIN 1
|
||||
#define Z_MAX_PIN 0
|
||||
#define Y_MAX_PIN 2
|
||||
#define X_MAX_PIN 6
|
||||
|
||||
|
||||
//
|
||||
// Z Probe (when not Z_MIN_PIN)
|
||||
@ -91,6 +121,12 @@
|
||||
//
|
||||
#define PS_ON_PIN 15
|
||||
|
||||
#if GEN7_VERSION < 13
|
||||
#define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM
|
||||
#else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header
|
||||
#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM
|
||||
#endif
|
||||
|
||||
// All these generations of Gen7 supply thermistor power
|
||||
// via PS_ON, so ignore bad thermistor readings
|
||||
#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
|
||||
@ -101,3 +137,13 @@
|
||||
#define TX_ENABLE_PIN 12
|
||||
#define RX_ENABLE_PIN 13
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_DIR_PIN 11
|
||||
#if GEN7_VERSION < 13
|
||||
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
|
||||
#else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header
|
||||
#define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM
|
||||
#endif
|
||||
|
||||
@ -24,6 +24,31 @@
|
||||
* Gen7 v1.3 pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* added pointer to a current Arduino IDE extension
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#define BOARD_NAME "Gen7 v1.3"
|
||||
|
||||
#define GEN7_VERSION 13 // v1.3
|
||||
|
||||
@ -24,8 +24,35 @@
|
||||
* Gen7 v1.4 pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* 1) added pointer to a current Arduino IDE extension
|
||||
* 2) added support for M3, M4 & M5 spindle control commands
|
||||
* 3) added case light pin definition
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
||||
#error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu."
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#define BOARD_NAME "Gen7 v1.4"
|
||||
@ -74,6 +101,7 @@
|
||||
// Misc. Functions
|
||||
//
|
||||
#define PS_ON_PIN 15
|
||||
#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM
|
||||
|
||||
// A pin for debugging
|
||||
#define DEBUG_PIN 0
|
||||
@ -81,3 +109,10 @@
|
||||
// RS485 pins
|
||||
#define TX_ENABLE_PIN 12
|
||||
#define RX_ENABLE_PIN 13
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 21
|
||||
|
||||
@ -27,8 +27,35 @@
|
||||
* Please review the pins and adjust them for your needs.
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* 1) added pointer to a current Arduino IDE extension
|
||||
* 2) added support for M3, M4 & M5 spindle control commands
|
||||
* 3) added case light pin definition
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
||||
#error "Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu."
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#define BOARD_NAME "Gen7 Custom"
|
||||
@ -76,6 +103,7 @@
|
||||
//
|
||||
#define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support
|
||||
#define PS_ON_PIN 19
|
||||
#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM
|
||||
|
||||
// A pin for debugging
|
||||
#define DEBUG_PIN -1
|
||||
@ -101,3 +129,10 @@
|
||||
// RS485 pins
|
||||
//#define TX_ENABLE_PIN 12
|
||||
//#define RX_ENABLE_PIN 13
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 6
|
||||
|
||||
@ -66,3 +66,8 @@
|
||||
#undef PS_ON_PIN
|
||||
#undef KILL_PIN
|
||||
#undef SD_DETECT_PIN
|
||||
|
||||
#if Z_STEP_PIN == 26
|
||||
#undef Z_STEP_PIN
|
||||
#define Z_STEP_PIN 32
|
||||
#endif
|
||||
|
||||
@ -127,6 +127,7 @@
|
||||
//
|
||||
#define SDSS 53
|
||||
#define LED_PIN 13
|
||||
#define CASE_LIGHT_PIN 2
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -152,3 +153,10 @@
|
||||
|
||||
#define SD_DETECT_PIN 49
|
||||
#endif // MINIPANEL
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 7 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 8
|
||||
|
||||
@ -97,6 +97,7 @@
|
||||
#define SDSS 53
|
||||
#define LED_PIN 13
|
||||
#define PS_ON_PIN 12
|
||||
#define CASE_LIGHT_PIN 2
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -120,3 +121,10 @@
|
||||
#define SD_DETECT_PIN -1 // RAMPS doesn't use this
|
||||
|
||||
#endif // ULTRA_LCD && NEWPANEL
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 4 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 11
|
||||
|
||||
@ -71,8 +71,8 @@
|
||||
#define E1_DIR_PIN 39
|
||||
#define E1_ENABLE_PIN 28
|
||||
|
||||
#define E2_STEP_PIN 23
|
||||
#define E2_DIR_PIN 24
|
||||
#define E2_STEP_PIN 23 // ? schematic says 24
|
||||
#define E2_DIR_PIN 24 // ? schematic says 23
|
||||
#define E2_ENABLE_PIN 22
|
||||
|
||||
//
|
||||
@ -112,6 +112,7 @@
|
||||
#define SDSS 53
|
||||
#define LED_PIN 13
|
||||
#define PS_ON_PIN 12
|
||||
#define CASE_LIGHT_PIN 2
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -129,3 +130,10 @@
|
||||
#define BTN_EN1 61
|
||||
#define BTN_EN2 59
|
||||
#define BTN_ENC 43
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 16 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 11
|
||||
|
||||
@ -28,6 +28,8 @@
|
||||
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#define MEGATRONICS_31
|
||||
|
||||
#if ENABLED(MEGATRONICS_31)
|
||||
#define BOARD_NAME "Megatronics v3.1"
|
||||
#else
|
||||
@ -129,6 +131,7 @@
|
||||
#define SDSS 53
|
||||
#define LED_PIN 13
|
||||
#define PS_ON_PIN 12
|
||||
#define CASE_LIGHT_PIN 45 // try the keypad connector
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -164,3 +167,27 @@
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#if DISABLED(REPRAPWORLD_KEYPAD) // try to use the keypad connector first
|
||||
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 43 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 42
|
||||
#elif EXTRUDERS <= 2
|
||||
// try to hijack the last extruder so that we can get the PWM signal off the Y breakout
|
||||
// move all the Y signals to the E2 extruder socket - makes dual Y steppers harder
|
||||
#undef Y_ENABLE_PIN
|
||||
#undef Y_STEP_PIN
|
||||
#undef Y_DIR_PIN
|
||||
#undef E2_STEP_PIN
|
||||
#undef E2_ENABLE_PIN
|
||||
#undef E2_DIR_PIN
|
||||
#define Y_ENABLE_PIN 23
|
||||
#define Y_STEP_PIN 22
|
||||
#define Y_DIR_PIN 60
|
||||
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 5
|
||||
#endif
|
||||
|
||||
@ -41,6 +41,17 @@
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 2 JAN 2017
|
||||
*
|
||||
* Added pin definitions for:
|
||||
* M3, M4 & M5 spindle control commands
|
||||
* case light
|
||||
*
|
||||
* Corrected pin assignment for MOSFET_B_PIN pin. Changed it from 9 to 11. The port
|
||||
* number (B5) agrees with the schematic but B5 is assigned to logical pin 11.
|
||||
*/
|
||||
|
||||
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
|
||||
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
@ -140,7 +151,7 @@
|
||||
// With no heated bed, an additional 24V fan is possible.
|
||||
//
|
||||
#define MOSFET_A_PIN 6 // H3
|
||||
#define MOSFET_B_PIN 11 // B5
|
||||
#define MOSFET_B_PIN 11 // B5 - Rev A of this file had this pin assigned to 9
|
||||
#define MOSFET_C_PIN 45 // L4
|
||||
#define MOSFET_D_PIN 44 // L5
|
||||
|
||||
@ -193,11 +204,11 @@
|
||||
#define LED_PIN 13 // B7
|
||||
#define CUTOFF_RESET_PIN 16 // H1
|
||||
#define CUTOFF_TEST_PIN 17 // H0
|
||||
#define CASE_LIGHT_PIN 44 // L5 MUST BE HARDWARE PWM
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
//
|
||||
|
||||
#ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
#define LCD_PINS_RS 33 // C4, LCD-STROBE
|
||||
@ -246,7 +257,6 @@
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
//
|
||||
// SD Card
|
||||
//
|
||||
@ -255,7 +265,20 @@
|
||||
|
||||
#define MAX_PIN THERMO_SCK_PIN
|
||||
|
||||
//check if all pins are defined in mega/pins_arduino.h
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 66 // K4 Pin should have a pullup!
|
||||
#define SPINDLE_LASER_PWM_PIN 8 // H5 MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 67 // K5
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
// Check if all pins are defined in mega/pins_arduino.h
|
||||
#include <Arduino.h>
|
||||
static_assert(NUM_DIGITAL_PINS > MAX_PIN, "add missing pins to [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h based on fastio.h"
|
||||
"to digital_pin_to_port_PGM, digital_pin_to_bit_mask_PGM, digital_pin_to_timer_PGM, NUM_DIGITAL_PINS, see below");
|
||||
|
||||
@ -111,6 +111,7 @@
|
||||
//
|
||||
#define SDSS 53
|
||||
#define LED_PIN 13
|
||||
#define CASE_LIGHT_PIN 9
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -140,3 +141,12 @@
|
||||
|
||||
#endif // NEWPANEL
|
||||
#endif // ULTRA_LCD
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
|
||||
// use P1 connector for spindle pins
|
||||
#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 18 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 19
|
||||
|
||||
@ -24,6 +24,13 @@
|
||||
* Minitronics v1.0/1.1 pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 2 JAN 2017
|
||||
*
|
||||
* Added pin definitions for M3, M4 & M5 spindle control commands
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef __AVR_ATmega1281__
|
||||
#error "Oops! Make sure you have 'Minitronics' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
@ -123,3 +130,19 @@
|
||||
|
||||
#define SD_DETECT_PIN -1 // Minitronics doesn't use this
|
||||
#endif
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE) // assumes we're only doing CNC work (no 3D printing)
|
||||
#undef HEATER_BED_PIN
|
||||
#undef TEMP_BED_PIN // need to free up some pins but also need to
|
||||
#undef TEMP_0_PIN // re-assign them (to unused pins) because Marlin
|
||||
#undef TEMP_1_PIN // requires the presence of certain pins or else it
|
||||
#define HEATER_BED_PIN 4 // won't compile
|
||||
#define TEMP_BED_PIN 50
|
||||
#define TEMP_0_PIN 51
|
||||
#define SPINDLE_LASER_ENABLE_PIN 52 // using A6 because it already has a pull up on it
|
||||
#define SPINDLE_LASER_PWM_PIN 3 // WARNING - LED & resistor pull up to +12/+24V stepper voltage
|
||||
#define SPINDLE_DIR_PIN 53
|
||||
#endif
|
||||
|
||||
@ -22,6 +22,8 @@
|
||||
|
||||
/**
|
||||
* MKS BASE 1.0 – Arduino Mega2560 with RAMPS v1.4 pin assignments
|
||||
*
|
||||
* Rev B - Override pin definitions for CASE_LIGHT and M3/M4/M5 spindle control
|
||||
*/
|
||||
|
||||
#if HOTENDS > 2 || E_STEPPERS > 2
|
||||
@ -36,4 +38,13 @@
|
||||
// Power outputs EFBF or EFBE
|
||||
#define MOSFET_D_PIN 7
|
||||
|
||||
#define CASE_LIGHT_PIN 2
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 2 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 15 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 19
|
||||
|
||||
#include "pins_RAMPS.h"
|
||||
@ -51,6 +51,31 @@
|
||||
* REF http://sanguino.cc/hardware
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* added pointer to a current Arduino IDE extension
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__)
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu. (Final OMCA board)"
|
||||
#endif
|
||||
|
||||
@ -50,8 +50,33 @@
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* added pointer to a current Arduino IDE extension
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef __AVR_ATmega644__
|
||||
#error "Oops! Make sure you have 'SanguinoA' selected from the 'Tools -> Boards' menu."
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#define BOARD_NAME "Alpha OMCA"
|
||||
|
||||
@ -137,6 +137,7 @@
|
||||
#define LED_PIN 13
|
||||
#define FILWIDTH_PIN 3 // Analog Input
|
||||
#define PS_ON_PIN 4
|
||||
#define CASE_LIGHT_PIN 46
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -208,3 +209,10 @@
|
||||
#endif // !NEWPANEL
|
||||
|
||||
#endif // ULTRA_LCD
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 31 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 32
|
||||
|
||||
@ -204,6 +204,16 @@
|
||||
|
||||
#define PS_ON_PIN 12
|
||||
|
||||
#if !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
|
||||
#undef CASE_LIGHT_PIN
|
||||
#if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first
|
||||
#define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM
|
||||
#elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) \
|
||||
&& (ENABLED(PANEL_ONE) || ENABLED(VIKI2) || ENABLED(miniVIKI) || ENABLED(MINIPANEL) || ENABLED(REPRAPWORLD_KEYPAD))) // try to use AUX 2
|
||||
#define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
//
|
||||
@ -361,3 +371,19 @@
|
||||
#endif // NEWPANEL
|
||||
|
||||
#endif // ULTRA_LCD
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE_PIN)
|
||||
#if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first
|
||||
#define SPINDLE_LASER_ENABLE_PIN 4 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 5
|
||||
#elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) \
|
||||
&& (ENABLED(PANEL_ONE) || ENABLED(VIKI2) || ENABLED(miniVIKI) || ENABLED(MINIPANEL) || ENABLED(REPRAPWORLD_KEYPAD))) // try to use AUX 2
|
||||
#define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 65
|
||||
#endif
|
||||
#endif
|
||||
|
||||
@ -101,3 +101,11 @@
|
||||
#define SDPOWER 48
|
||||
#define SDSS 53
|
||||
#define LED_PIN 13
|
||||
#define CASE_LIGHT_PIN 45 // MUST BE HARDWARE PWM
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 43
|
||||
|
||||
@ -100,7 +100,7 @@
|
||||
#endif
|
||||
|
||||
#if TEMP_SENSOR_2 == -1
|
||||
#define TEMP_2_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can't be used when TEMP_SENSOR_BED is defined as thermocouple)
|
||||
#define TEMP_2_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_BED is defined as thermocouple)
|
||||
#else
|
||||
#define TEMP_2_PIN 13 // Analog Input (default connector for thermistor *T2* on rumba board is used)
|
||||
#endif
|
||||
@ -109,7 +109,7 @@
|
||||
//#define TEMP_X_PIN 12 // Analog Input (default connector for thermistor *T3* on rumba board is used)
|
||||
|
||||
#if TEMP_SENSOR_BED == -1
|
||||
#define TEMP_BED_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can't be used when TEMP_SENSOR_2 is defined as thermocouple)
|
||||
#define TEMP_BED_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can not be used when TEMP_SENSOR_2 is defined as thermocouple)
|
||||
#else
|
||||
#define TEMP_BED_PIN 11 // Analog Input (default connector for thermistor *THB* on rumba board is used)
|
||||
#endif
|
||||
@ -133,6 +133,7 @@
|
||||
#define LED_PIN 13
|
||||
#define PS_ON_PIN 45
|
||||
#define KILL_PIN 46
|
||||
#define CASE_LIGHT_PIN 45
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -148,3 +149,10 @@
|
||||
#define BTN_EN1 11
|
||||
#define BTN_EN2 12
|
||||
#define BTN_ENC 43
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 14 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 15
|
||||
|
||||
@ -24,6 +24,33 @@
|
||||
* Sanguinololu board pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* 1) added pointer to a current Arduino IDE extension
|
||||
* 2) added support for M3, M4 & M5 spindle control commands
|
||||
* 3) added case light pin definition
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
|
||||
#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
@ -96,19 +123,26 @@
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
|
||||
/**
|
||||
* On some broken versions of the Sanguino libraries the pin definitions are wrong,
|
||||
* which then needs SDSS as pin 24. But you should upgrade your Sanguino libraries! See #368.
|
||||
* In some versions of the Sanguino libraries the pin
|
||||
* definitions are wrong, with SDSS = 24 and LED_PIN = 28 (Melzi).
|
||||
* If you encounter issues with these pins, upgrade your
|
||||
* Sanguino libraries! See #368.
|
||||
*/
|
||||
//#define SDSS 24
|
||||
#define SDSS 31
|
||||
|
||||
#if IS_MELZI
|
||||
#define LED_PIN 27 // On some broken versions of the Sanguino libraries the pin definitions are wrong, so LED_PIN needs to be 28. But you should upgrade your Sanguino libraries! See #368.
|
||||
#define LED_PIN 27
|
||||
#elif MB(STB_11)
|
||||
#define LCD_BACKLIGHT_PIN 17 // LCD backlight LED
|
||||
#endif
|
||||
|
||||
#if DISABLED(SPINDLE_LASER_ENABLE) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // try to use IO Header
|
||||
#define CASE_LIGHT_PIN 4 // MUST BE HARDWARE PWM - see if IO Header is available
|
||||
#endif
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
//
|
||||
@ -181,14 +215,62 @@
|
||||
#else
|
||||
#define BTN_ENC 30
|
||||
#endif
|
||||
#elif ENABLED(OLED_PANEL_TINYBOY2)
|
||||
#define BTN_ENC 28
|
||||
#define LCD_SDSS -1
|
||||
#else // !Panelolu2, !TinyBoy2
|
||||
#else // !Panelolu2
|
||||
#define BTN_ENC 16
|
||||
#define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi
|
||||
#endif // !Panelolu2, !TinyBoy2
|
||||
#endif // !Panelolu2
|
||||
|
||||
#define SD_DETECT_PIN -1
|
||||
|
||||
#endif // ULTRA_LCD && NEWPANEL
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
#if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // try to use IO Header
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup/pulldown!
|
||||
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 11
|
||||
|
||||
#elif !MB(MELZI) // use X stepper motor socket
|
||||
|
||||
/**
|
||||
* To control the spindle speed and have an LCD you must sacrifice
|
||||
* the Extruder and pull some signals off the X stepper driver socket.
|
||||
*
|
||||
* The following assumes:
|
||||
* - The X stepper driver socket is empty
|
||||
* - The extruder driver socket has a driver board plugged into it
|
||||
* - The X stepper wires are attached the the extruder connector
|
||||
*/
|
||||
|
||||
/**
|
||||
* Where to get the spindle signals
|
||||
*
|
||||
* spindle signal socket name socket name
|
||||
* -------
|
||||
* /ENABLE O| |O VMOT
|
||||
* MS1 O| |O GND
|
||||
* MS2 O| |O 2B
|
||||
* MS3 O| |O 2A
|
||||
* /RESET O| |O 1A
|
||||
* /SLEEP O| |O 1B
|
||||
* SPINDLE_LASER_PWM_PIN STEP O| |O VDD
|
||||
* SPINDLE_LASER_ENABLE_PIN DIR O| |O GND
|
||||
* -------
|
||||
*
|
||||
* Note: Socket names vary from vendor to vendor.
|
||||
*/
|
||||
#undef X_DIR_PIN
|
||||
#undef X_ENABLE_PIN
|
||||
#undef X_STEP_PIN
|
||||
#define X_DIR_PIN 0
|
||||
#define X_ENABLE_PIN 14
|
||||
#define X_STEP_PIN 1
|
||||
#define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 21 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN -1 // No pin available on the socket for the direction pin
|
||||
#endif
|
||||
#endif // SPINDLE_LASER_ENABLE
|
||||
|
||||
@ -115,7 +115,6 @@
|
||||
#define EXT_AUX_A4 4 // Analog
|
||||
#define EXT_AUX_A4_IO 44 // Digital IO, 42 (teensy), 44 (marlin)
|
||||
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
//
|
||||
@ -134,10 +133,23 @@
|
||||
#endif // SAV_3DLCD
|
||||
|
||||
#if ENABLED(SAV_3DLCD) || ENABLED(SAV_3DGLCD)
|
||||
|
||||
#define BTN_EN1 EXT_AUX_A1_IO
|
||||
#define BTN_EN2 EXT_AUX_A0_IO
|
||||
#define BTN_ENC EXT_AUX_PWM_D24
|
||||
|
||||
#define KILL_PIN EXT_AUX_A2_IO
|
||||
#define HOME_PIN EXT_AUX_A4_IO
|
||||
#endif // SAV_3DLCD || SAV_3DGLCD
|
||||
|
||||
#else // Try to use the expansion header for spindle control
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 24 // 12 AT90USB… pin #
|
||||
#define SPINDLE_LASER_ENABLE_PIN 39 // Pin should have a pullup! 41 AT90USB… pin #
|
||||
#define SPINDLE_DIR_PIN 40 // 42 AT90USB… pin #
|
||||
|
||||
#define CASE_LIGHT_PIN 0 // 24 AT90USB… pin #
|
||||
|
||||
#endif
|
||||
|
||||
@ -24,6 +24,31 @@
|
||||
* Sethi 3D_1 pin assignments - www.sethi3d.com.br
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 26 DEC 2016
|
||||
*
|
||||
* added pointer to a current Arduino IDE extension
|
||||
* this assumes that this board uses the Sanguino pin map
|
||||
*/
|
||||
|
||||
/**
|
||||
* A useable Arduino IDE extension (board manager) can be found at
|
||||
* https://github.com/Lauszus/Sanguino
|
||||
*
|
||||
* This extension has been tested on Arduino 1.6.12 & 1.8.0
|
||||
*
|
||||
* Here's the JSON path:
|
||||
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
|
||||
*
|
||||
* When installing select 1.0.2
|
||||
*
|
||||
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
|
||||
* Just use the above JSON URL instead of Sparkfun's JSON.
|
||||
*
|
||||
* Once installed select the Sanguino board and then select the CPU.
|
||||
*
|
||||
*/
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
||||
#error "Oops! Make sure you have 'Sethi 3D' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
@ -124,6 +124,7 @@
|
||||
#define SDSS 20 // 8
|
||||
#define LED_PIN 6
|
||||
#define PS_ON_PIN 27
|
||||
#define CASE_LIGHT_PIN 1 // MUST BE HARDWARE PWM
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -139,3 +140,10 @@
|
||||
#define BTN_EN2 39
|
||||
#define BTN_ENC 40
|
||||
#endif
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_ENABLE_PIN 5 // Pin should have a pullup!
|
||||
#define SPINDLE_LASER_PWM_PIN 0 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_DIR_PIN 7
|
||||
|
||||
@ -21,18 +21,73 @@
|
||||
*/
|
||||
|
||||
/**
|
||||
* Teensylu 0.7 pin assignments (AT90USB1286)
|
||||
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
|
||||
* http://www.pjrc.com/teensy/teensyduino.html
|
||||
* See http://reprap.org/wiki/Printrboard for more info
|
||||
* rev B 30 DEC 2016
|
||||
*
|
||||
* The original version of this file did NOT result in a useful program because:
|
||||
* 1. The pin numbers assumed that the "#define AT90USBxx_TEENSYPP_ASSIGNMENTS" line
|
||||
* in FASTIO.h was commented out. There wasn't an Arduino IDE 1.6.x extension/package
|
||||
* that supported this pin map so the latest Marlin wouldn't compile.
|
||||
* 2. The silkscreen for the four end stops don't agree with the schematic. Activating
|
||||
* the X endstop would tell the software that the Y endstop just went active.
|
||||
* 3. The thermistor inputs also had heater names assigned to them. The result was
|
||||
* thermistor inputs that were set to digital outputs.
|
||||
*
|
||||
* Rev B corrects the above problems by:
|
||||
* 1. The "Marlin_AT90USB" extension/package was developed. This extension enables the
|
||||
* latest Marlin software to compile using Arduino IDE 1.6.x and 1.80.
|
||||
* 2. The endstop pin numbers in this file were changed to match the silkscreen. This
|
||||
* makes it a little confusing when trying to correlate the schematic with the pin
|
||||
* numbers used in this file.
|
||||
* 3. The offending heater names were deleted.
|
||||
*
|
||||
* To create a useable image for Teensylu do the following:
|
||||
* a) Install the Marlin_AT90USB extension with either of the following methods:
|
||||
* Automatic - paste this URL into preferences and then use Boards manager
|
||||
* https://rawgit.com/Bob-the-Kuhn/Marlin_AT90USB/master/package_MARLIN_AT90USB_index.json
|
||||
* Manual:
|
||||
* 1. Copy the following URL into Go to "https://github.com/Bob-the-Kuhn/Marlin_AT90USB",
|
||||
* click on the "Clone or Download" button and then click on "Download ZIP" button.
|
||||
* 2. Unzip the file, find the "Marlin_AT90USB" directory and then copy it to the
|
||||
* hardware directory in Arduino. The Arduino hardware directory will probably be
|
||||
* located in a path similar to this: C:\Program Files (x86)\Arduino\hardware
|
||||
* b) Connect the USBtinyISP to the board.
|
||||
* c) In the Arduino IDE select the "AT90USB1286_STANDARD" board in the of the "Marlin_AT90USB"
|
||||
* section and select the "USBtinyISP" programmer.
|
||||
* d) In the Arduino IDE click on "burn bootloader". Don't worry about the "verify
|
||||
* failed at 1F000" error message.
|
||||
* e) The USBtinyISP programmer is no longer needed. Remove it.
|
||||
* f) In FASTIO.h comment out the "#define AT90USBxx_TEENSYPP_ASSIGNMENTS" line.
|
||||
* g) To upload a sketch do the following:
|
||||
* 1. remove the jumper
|
||||
* 2. press reset
|
||||
* 3. click on the "upload" button in the Arduino IDE
|
||||
* 4. wait until the upload finishes (less than a minute)
|
||||
* 5. put the jumper back on
|
||||
* 6. press the reset button
|
||||
*
|
||||
*
|
||||
* NOTE - the "Marlin_AT90USB" pin maps make PWM0A available rather than the usual PWM1C.
|
||||
* These PWMs share the same physical pin. Marlin uses TIMER1 to generate
|
||||
* interrupts and sets it up such that PWM1A, PWM1B & PWM1C can not be used.
|
||||
*/
|
||||
|
||||
#ifndef __AVR_AT90USB1286__
|
||||
#error "Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu."
|
||||
/**
|
||||
* SILKSCREEN ERROR
|
||||
*
|
||||
* The silkscreen for the endstops do NOT match the schematic. The silkscreen SHOULD
|
||||
* read (from left to right) X-STOP, Y-STOP, Z-STOP & E-STOP. The silkscreen actually
|
||||
* reads E-STOP, X-STOP, Y-STOP & Z-STOP.
|
||||
*
|
||||
* The pin assignments in this file match the silkscreen.
|
||||
*/
|
||||
|
||||
|
||||
#if !defined(__AVR_AT90USB1286__) && !defined(__AVR_AT90USB1286P__)
|
||||
#error "Oops! Make sure you have 'AT90USB1286_STANDARD' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS) // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional.
|
||||
#error "These Teensylu assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h"
|
||||
#if ENABLED(AT90USBxx_TEENSYPP_ASSIGNMENTS)
|
||||
#error "please disable (comment out) the AT90USBxx_TEENSYPP_ASSIGNMENTS flag in FASTIO.h "
|
||||
#endif
|
||||
|
||||
#define BOARD_NAME "Teensylu"
|
||||
@ -40,12 +95,23 @@
|
||||
#define USBCON 1286 // Disable MarlinSerial etc.
|
||||
#define LARGE_FLASH true
|
||||
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
// Limit Switche definitions that match the SCHEMATIC
|
||||
//
|
||||
#define X_STOP_PIN 13
|
||||
#define Y_STOP_PIN 14
|
||||
#define Z_STOP_PIN 15
|
||||
//#define X_STOP_PIN 13
|
||||
//#define Y_STOP_PIN 14
|
||||
//#define Z_STOP_PIN 15
|
||||
//#define E_STOP_PIN 36
|
||||
|
||||
|
||||
//
|
||||
// Limit Switch definitions that match the SILKSCREEN
|
||||
//
|
||||
#define X_STOP_PIN 14
|
||||
#define Y_STOP_PIN 15
|
||||
#define Z_STOP_PIN 36
|
||||
//#define E_STOP_PIN 13
|
||||
|
||||
//
|
||||
// Steppers
|
||||
@ -66,9 +132,9 @@
|
||||
#define E0_DIR_PIN 7
|
||||
#define E0_ENABLE_PIN 19
|
||||
|
||||
//
|
||||
|
||||
// Temperature Sensors
|
||||
//
|
||||
|
||||
#define TEMP_0_PIN 7 // Analog Input (Extruder)
|
||||
#define TEMP_BED_PIN 6 // Analog Input (Bed)
|
||||
|
||||
@ -76,22 +142,15 @@
|
||||
// Heaters / Fans
|
||||
//
|
||||
#define HEATER_0_PIN 21 // Extruder
|
||||
#define HEATER_1_PIN 46
|
||||
#define HEATER_2_PIN 47
|
||||
#define HEATER_BED_PIN 20
|
||||
|
||||
// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin
|
||||
// fastio pin numbering otherwise
|
||||
#if ENABLED(FAN_SOFT_PWM) || ENABLED(FAST_PWM_FAN)
|
||||
#define FAN_PIN 22
|
||||
#else
|
||||
#define FAN_PIN 16
|
||||
#endif
|
||||
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
#define SDSS 8
|
||||
#define CASE_LIGHT_PIN 24
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -101,13 +160,19 @@
|
||||
#define BEEPER_PIN -1
|
||||
|
||||
#if ENABLED(LCD_I2C_PANELOLU2)
|
||||
#define BTN_EN1 27 // RX1 - fastio.h pin mapping 27
|
||||
#define BTN_EN2 26 // TX1 - fastio.h pin mapping 26
|
||||
#define BTN_ENC 43 // A3 - fastio.h pin mapping 43
|
||||
#define SDSS 40 // use SD card on Panelolu2 (Teensyduino pin mapping)
|
||||
#define BTN_EN1 27
|
||||
#define BTN_EN2 26
|
||||
#define BTN_ENC 43
|
||||
#define SDSS 40 // use SD card on Panelolu2
|
||||
#endif // LCD_I2C_PANELOLU2
|
||||
|
||||
#define SD_DETECT_PIN -1
|
||||
|
||||
#endif // ULTRA_LCD && NEWPANEL
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 42
|
||||
|
||||
@ -24,6 +24,14 @@
|
||||
* Ultiboard v2.0 pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 2 JAN 2017
|
||||
*
|
||||
* Added pin definitions for:
|
||||
* M3, M4 & M5 spindle control commands
|
||||
* case light
|
||||
*/
|
||||
|
||||
#ifndef __AVR_ATmega2560__
|
||||
#error "Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
@ -110,3 +118,16 @@
|
||||
#define BTN_EN1 40
|
||||
#define BTN_EN2 41
|
||||
#define BTN_ENC 19
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE) // use the LED_PIN for spindle speed control or case light
|
||||
#undef LED_PIN
|
||||
#define SPINDLE_DIR_PIN 16
|
||||
#define SPINDLE_LASER_ENABLE_PIN 17 // Pin should have a pullup!
|
||||
#define SPINDLE_LASER_PWM_PIN 8 // MUST BE HARDWARE PWM
|
||||
#else
|
||||
#undef LED_PIN
|
||||
#define CASE_LIGHT_PIN 8
|
||||
#endif
|
||||
|
||||
@ -24,6 +24,14 @@
|
||||
* Ultimaker pin assignments
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 2 JAN 2017
|
||||
*
|
||||
* Added pin definitions for:
|
||||
* M3, M4 & M5 spindle control commands
|
||||
* case light
|
||||
*/
|
||||
|
||||
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
|
||||
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
@ -102,6 +110,7 @@
|
||||
#define LED_PIN 13
|
||||
#define PS_ON_PIN 12
|
||||
#define SUICIDE_PIN 54 // PIN that has to be turned on right after start, to keep power flowing.
|
||||
#define CASE_LIGHT_PIN 8
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
@ -146,3 +155,10 @@
|
||||
#endif // !NEWPANEL
|
||||
|
||||
#endif // ULTRA_LCD
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 10 // Pin should have a pullup!
|
||||
#define SPINDLE_DIR_PIN 11 // use the EXP3 PWM header
|
||||
|
||||
@ -24,6 +24,42 @@
|
||||
* Ultimaker pin assignments (Old electronics)
|
||||
*/
|
||||
|
||||
/**
|
||||
* Rev B 3 JAN 2017
|
||||
*
|
||||
* Details on pin definitions for M3, M4 & M5 spindle control commands and for
|
||||
* the CASE_LIGHT_PIN are at the end of this file.
|
||||
*
|
||||
* This started out as an attempt to add pin definitions for M3, M4 & M5 spindle
|
||||
* control commands but quickly turned into a head scratcher as the sources for
|
||||
* the revisions provided inconsistent information.
|
||||
*
|
||||
* As best I can determine:
|
||||
* 1.5.3 boards should use the pins_ULTIMAKER.h file which means the BOARD_NAME
|
||||
* define in this file should say 1.5.3 rather than 1.5.4
|
||||
* This file is meant for 1.1 - 1.3 boards.
|
||||
* The endstops for the 1.0 boards use different definitions than on the 1.1 - 1.3
|
||||
* boards.
|
||||
*
|
||||
* I've added sections that have the 1.0 and 1.5.3 + endstop definitions so you can
|
||||
* easily switch if needed. I've also copied over the 1.5.3 + LCD definitions.
|
||||
*
|
||||
* To be 100% sure of the board you have:
|
||||
* 1. In Configuration_adv.h enable "PINS_DEBUGGING"
|
||||
* 2. Compile & uploade
|
||||
* 3. Enter the command "M43 W1 I1". This command will report that pin nmumber and
|
||||
* name of any pin that changes state.
|
||||
* 4. Using a 1k (approximately) resistor pull the endstops and some of the LCD pins
|
||||
* to ground and see what is reported.
|
||||
* 5. If the reported pin doesn't match the file then try a different board revision
|
||||
* and repeat steps 2 - 5
|
||||
*/
|
||||
|
||||
#define board_rev_1_1_TO_1_3
|
||||
//#define board_rev_1_0
|
||||
//#define board_rev_1_5
|
||||
|
||||
|
||||
#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
|
||||
#error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
@ -37,18 +73,38 @@
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#define X_MIN_PIN 15
|
||||
#define X_MAX_PIN 14
|
||||
#define Y_MIN_PIN 17
|
||||
#define Y_MAX_PIN 16
|
||||
#define Z_MIN_PIN 19
|
||||
#define Z_MAX_PIN 18
|
||||
#if ENABLED(board_rev_1_1_TO_1_3)
|
||||
#define X_MIN_PIN 15 // SW1
|
||||
#define X_MAX_PIN 14 // SW2
|
||||
#define Y_MIN_PIN 17 // SW3
|
||||
#define Y_MAX_PIN 16 // SW4
|
||||
#define Z_MIN_PIN 19 // SW5
|
||||
#define Z_MAX_PIN 18 // SW6
|
||||
#endif
|
||||
|
||||
#if ENABLED(board_rev_1_0)
|
||||
#define X_MIN_PIN 13 // SW1
|
||||
#define X_MAX_PIN 12 // SW2
|
||||
#define Y_MIN_PIN 11 // SW3
|
||||
#define Y_MAX_PIN 10 // SW4
|
||||
#define Z_MIN_PIN 9 // SW5
|
||||
#define Z_MAX_PIN 8 // SW6
|
||||
#endif
|
||||
|
||||
#if ENABLED(board_rev_1_5)
|
||||
#define X_MIN_PIN 22
|
||||
#define X_MAX_PIN 24
|
||||
#define Y_MIN_PIN 26
|
||||
#define Y_MAX_PIN 28
|
||||
#define Z_MIN_PIN 30
|
||||
#define Z_MAX_PIN 32
|
||||
#endif
|
||||
|
||||
//
|
||||
// Z Probe (when not Z_MIN_PIN)
|
||||
//
|
||||
#ifndef Z_MIN_PROBE_PIN
|
||||
#define Z_MIN_PROBE_PIN 18
|
||||
#define Z_MIN_PROBE_PIN Z_MAX_PIN
|
||||
#endif
|
||||
|
||||
//
|
||||
@ -70,9 +126,9 @@
|
||||
#define E0_DIR_PIN 45
|
||||
#define E0_ENABLE_PIN 41
|
||||
|
||||
#define E1_STEP_PIN -1
|
||||
#define E1_DIR_PIN -1
|
||||
#define E1_ENABLE_PIN -1
|
||||
#define E1_STEP_PIN -1 // 49
|
||||
#define E1_DIR_PIN -1 // 47
|
||||
#define E1_ENABLE_PIN -1 // 48
|
||||
|
||||
//
|
||||
// Temperature Sensors
|
||||
@ -84,14 +140,144 @@
|
||||
// Heaters / Fans
|
||||
//
|
||||
#define HEATER_0_PIN 2
|
||||
#define HEATER_1_PIN 1
|
||||
//#define HEATER_1_PIN 3 // used for case light Rev A said "1"
|
||||
#define HEATER_BED_PIN 4
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
//
|
||||
#if ENABLED(board_rev_1_0) || ENABLED(board_rev_1_1_TO_1_3)
|
||||
#define LCD_PINS_RS 24
|
||||
#define LCD_PINS_ENABLE 22
|
||||
#define LCD_PINS_D4 36
|
||||
#define LCD_PINS_D5 34
|
||||
#define LCD_PINS_D6 32
|
||||
#define LCD_PINS_D7 30
|
||||
#elif ENABLED(board_rev_1_5) && ENABLED(ULTRA_LCD)
|
||||
|
||||
#define BEEPER_PIN 18
|
||||
|
||||
#if ENABLED(NEWPANEL)
|
||||
|
||||
#define LCD_PINS_RS 20
|
||||
#define LCD_PINS_ENABLE 17
|
||||
#define LCD_PINS_D4 16
|
||||
#define LCD_PINS_D5 21
|
||||
#define LCD_PINS_D6 5
|
||||
#define LCD_PINS_D7 6
|
||||
|
||||
// buttons are directly attached
|
||||
#define BTN_EN1 40
|
||||
#define BTN_EN2 42
|
||||
#define BTN_ENC 19
|
||||
|
||||
#define SD_DETECT_PIN 38
|
||||
|
||||
#else // !NEWPANEL - Old style panel with shift register
|
||||
|
||||
// buttons are attached to a shift register
|
||||
#define SHIFT_CLK 38
|
||||
#define SHIFT_LD 42
|
||||
#define SHIFT_OUT 40
|
||||
#define SHIFT_EN 17
|
||||
|
||||
#define LCD_PINS_RS 16
|
||||
#define LCD_PINS_ENABLE 5
|
||||
#define LCD_PINS_D4 6
|
||||
#define LCD_PINS_D5 21
|
||||
#define LCD_PINS_D6 20
|
||||
#define LCD_PINS_D7 19
|
||||
|
||||
#define SD_DETECT_PIN -1
|
||||
|
||||
#endif // !NEWPANEL
|
||||
|
||||
#endif // ULTRA_LCD
|
||||
|
||||
//
|
||||
// case light - see spindle section for more info on available hardware PWMs
|
||||
//
|
||||
#if !PIN_EXISTS(CASE_LIGHT) && ENABLED(board_rev_1_5)
|
||||
#define CASE_LIGHT_PIN 7 // use PWM - MUST BE HARDWARE PWM
|
||||
#endif
|
||||
|
||||
//
|
||||
// M3/M4/M5 - Spindle/Laser Control
|
||||
//
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#if ENABLED(board_rev_1_0) // use the last three SW positions
|
||||
|
||||
#undef Z_MIN_PROBE_PIN
|
||||
#undef X_MIN_PIN // SW1
|
||||
#undef X_MAX_PIN // SW2
|
||||
#undef Y_MIN_PIN // SW3
|
||||
#undef Y_MAX_PIN // SW4
|
||||
#undef Z_MIN_PIN // SW5
|
||||
#undef Z_MAX_PIN // SW6
|
||||
|
||||
#define X_STOP_PIN 13 // SW1 (didn't change) - also has a useable hardware PWM
|
||||
#define Y_STOP_PIN 12 // SW2
|
||||
#define Z_STOP_PIN 11 // SW3
|
||||
|
||||
#define SPINDLE_DIR_PIN 10 // SW4
|
||||
#define SPINDLE_LASER_PWM_PIN 9 // SW5 MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 8 // SW6 Pin should have a pullup!
|
||||
|
||||
#elif ENABLED(board_rev_1_5) // use the same pins - but now they are on a different connector
|
||||
|
||||
#define SPINDLE_DIR_PIN 10 // EXP3-6 (silkscreen says 10)
|
||||
#define SPINDLE_LASER_PWM_PIN 9 // EXP3-7 (silkscreen says 9) MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 8 // EXP3-8 (silkscreen says 8) Pin should have a pullup!
|
||||
|
||||
#elif ENABLED(board_rev_1_1_TO_1_3)
|
||||
|
||||
/**
|
||||
* Only four hardware PWMs physically connected to anything on these boards:
|
||||
*
|
||||
* HEATER_0_PIN 2 silkscreen varies - usually "PWM 1" or "HEATER1"
|
||||
* HEATER_1_PIN 3 silkscreen varies - usually "PWM 2" or "HEATER2"
|
||||
* HEATER_BED_PIN 4 silkscreen varies - usually "PWM 3" or "HEATED BED"
|
||||
* E0_DIR_PIN 45
|
||||
*
|
||||
* If one of the heaters is used then special precautions will usually be needed.
|
||||
* They have an LED and resistor pullup to +24V which could damage 3.3V-5V ICs.
|
||||
*/
|
||||
#if EXTRUDERS == 1 // Move E0 stepper module to the spare and get signals from E0
|
||||
#undef E0_STEP_PIN
|
||||
#undef E0_DIR_PIN
|
||||
#undef E0_ENABLE_PIN
|
||||
#define E0_STEP_PIN 49
|
||||
#define E0_DIR_PIN 47
|
||||
#define E0_ENABLE_PIN 48
|
||||
#define SPINDLE_DIR_PIN 43
|
||||
#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM
|
||||
#define SPINDLE_LASER_ENABLE_PIN 41 // Pin should have a pullup!
|
||||
#elif TEMP_SENSOR_BED == 0 // Can't use E0 so see if HEATER_BED_PIN is available
|
||||
#undef HEATER_BED_PIN
|
||||
#define SPINDLE_DIR_PIN 38 // Probably pin 4 on 10 pin connector closest to the E0 socket
|
||||
#define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM - Special precautions usually needed.
|
||||
#define SPINDLE_LASER_ENABLE_PIN 40 // Pin should have a pullup! (Probably pin 6 on the 10-pin
|
||||
// connector closest to the E0 socket)
|
||||
#endif
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Where to get the spindle signals on the E0 socket
|
||||
*
|
||||
* spindle signal socket name socket name
|
||||
* -------
|
||||
* SPINDLE_LASER_ENABLE_PIN /ENABLE *| |O VMOT
|
||||
* MS1 O| |O GND
|
||||
* MS2 O| |O 2B
|
||||
* MS3 O| |O 2A
|
||||
* /RESET O| |O 1A
|
||||
* /SLEEP O| |O 1B
|
||||
* SPINDLE_DIR_PIN STEP O| |O VDD
|
||||
* SPINDLE_LASER_PWM_PIN DIR O| |O GND
|
||||
* -------
|
||||
* * - pin closest to MS1, MS2 & MS3 jumpers on the board
|
||||
*
|
||||
* Note: Socket names vary from vendor to vendor.
|
||||
*/
|
||||
|
||||
Loading…
Reference in New Issue
Block a user