bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

Printrboard G2 support (#13116)

Browse Source
This commit is contained in:
Bob Kuhn
2019-02-26 21:03:13 -06:00
committed by Scott Lahteine
parent 4200f9ed62
commit ddbe4cfa20
12 changed files with 3009 additions and 124 deletions
Download Patch File Download Diff File Expand all files Collapse all files

145
Marlin/src/HAL/HAL_DUE/G2_PWM.cpp Normal file
View File

@ -0,0 +1,145 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* The PWM module is only used to generate interrupts at specified times. It
* is NOT used to directly toggle pins. The ISR writes to the pin assigned to
* that interrupt.
*
* All PWMs use the same repetition rate. The G2 needs about 10KHz min in order to
* not have obvious ripple on the Vref signals.
*
* The data structures are setup to minimize the computation done by the ISR which
* minimizes ISR execution time. Execution times are 0.8 to 1.1 microseconds.
*
* FIve PWM interrupt sources are used. Channel 0 sets the base period. All Vref
* signals are set active when this counter overflows and resets to zero. The compare
* values in channels 1-4 are set to give the desired duty cycle for that Vref pin.
* When counter 0 matches the compare value then that channel generates an interrupt.
* The ISR checks the source of the interrupt and sets the corresponding pin inactive.
*
* Some jitter in the Vref signal is OK so the interrupt priority is left at its default value.
*/
#include "../../inc/MarlinConfig.h"
#if MB(PRINTRBOARD_G2)
#include "G2_PWM.h"
volatile uint32_t *SODR_A = &PIOA->PIO_SODR,
*SODR_B = &PIOB->PIO_SODR,
*CODR_A = &PIOA->PIO_CODR,
*CODR_B = &PIOB->PIO_CODR;
PWM_map ISR_table[NUM_PWMS] = PWM_MAP_INIT;
void Stepper::digipot_init() {
OUT_WRITE(MOTOR_CURRENT_PWM_X_PIN, 0); // init pins
OUT_WRITE(MOTOR_CURRENT_PWM_Y_PIN, 0);
OUT_WRITE(MOTOR_CURRENT_PWM_Z_PIN, 0);
OUT_WRITE(MOTOR_CURRENT_PWM_E_PIN, 0);
#define WPKEY (0x50574D << 8) // “PWM” in ASCII
#define WPCMD_DIS_SW 0 // command to disable Write Protect SW
#define WPRG_ALL (PWM_WPCR_WPRG0 | PWM_WPCR_WPRG1 | PWM_WPCR_WPRG2 | PWM_WPCR_WPRG3 | PWM_WPCR_WPRG4 | PWM_WPCR_WPRG5) // all Write Protect Groups
#define PWM_CLOCK_F F_CPU / 1000000UL // set clock to 1MHz
PMC->PMC_PCER1 = PMC_PCER1_PID36; // enable PWM controller clock (disabled on power up)
PWM->PWM_WPCR = WPKEY | WPRG_ALL | WPCMD_DIS_SW; // enable setting of all PWM registers
PWM->PWM_CLK = PWM_CLOCK_F; // enable CLK_A and set it to 1MHz, leave CLK_B disabled
PWM->PWM_CH_NUM[0].PWM_CMR = 0b1011; // set channel 0 to Clock A input & to left aligned
PWM->PWM_CH_NUM[1].PWM_CMR = 0b1011; // set channel 1 to Clock A input & to left aligned
PWM->PWM_CH_NUM[2].PWM_CMR = 0b1011; // set channel 2 to Clock A input & to left aligned
PWM->PWM_CH_NUM[3].PWM_CMR = 0b1011; // set channel 3 to Clock A input & to left aligned
PWM->PWM_CH_NUM[4].PWM_CMR = 0b1011; // set channel 4 to Clock A input & to left aligned
PWM->PWM_CH_NUM[0].PWM_CPRD = PWM_PERIOD_US; // set channel 0 Period
PWM->PWM_IER2 = PWM_IER1_CHID0; // generate interrupt when counter0 overflows
PWM->PWM_IER2 = PWM_IER2_CMPM0 | PWM_IER2_CMPM1 | PWM_IER2_CMPM2 | PWM_IER2_CMPM3 | PWM_IER2_CMPM4; // generate interrupt on compare event
PWM->PWM_CMP[1].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[0])); // interrupt when counter0 == CMPV - used to set Motor 1 PWM inactive
PWM->PWM_CMP[2].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[0])); // interrupt when counter0 == CMPV - used to set Motor 2 PWM inactive
PWM->PWM_CMP[3].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[1])); // interrupt when counter0 == CMPV - used to set Motor 3 PWM inactive
PWM->PWM_CMP[4].PWM_CMPV = 0x010000000LL | G2_VREF_COUNT(G2_VREF(motor_current_setting[2])); // interrupt when counter0 == CMPV - used to set Motor 4 PWM inactive
PWM->PWM_CMP[1].PWM_CMPM = 0x0001; // enable compare event
PWM->PWM_CMP[2].PWM_CMPM = 0x0001; // enable compare event
PWM->PWM_CMP[3].PWM_CMPM = 0x0001; // enable compare event
PWM->PWM_CMP[4].PWM_CMPM = 0x0001; // enable compare event
PWM->PWM_SCM = PWM_SCM_UPDM_MODE0 | PWM_SCM_SYNC0 | PWM_SCM_SYNC1 | PWM_SCM_SYNC2 | PWM_SCM_SYNC3 | PWM_SCM_SYNC4; // sync 1-4 with 0, use mode 0 for updates
PWM->PWM_ENA = PWM_ENA_CHID0 | PWM_ENA_CHID1 | PWM_ENA_CHID2 | PWM_ENA_CHID3 | PWM_ENA_CHID4; // enable the channels used by G2
PWM->PWM_IER1 = PWM_IER1_CHID0 | PWM_IER1_CHID1 | PWM_IER1_CHID2 | PWM_IER1_CHID3 | PWM_IER1_CHID4; // enable interrupts for the channels used by G2
NVIC_EnableIRQ(PWM_IRQn); // Enable interrupt handler
NVIC_SetPriority(PWM_IRQn, NVIC_EncodePriority(0, 10, 0)); // normal priority for PWM module (can stand some jitter on the Vref signals)
}
void Stepper::digipot_current(const uint8_t driver, const int16_t current) {
if (!(PWM->PWM_CH_NUM[0].PWM_CPRD == PWM_PERIOD_US)) digipot_init(); // Init PWM system if needed
switch (driver) {
case 0: PWM->PWM_CMP[1].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current)); // update X & Y
PWM->PWM_CMP[2].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current));
PWM->PWM_CMP[1].PWM_CMPMUPD = 0x0001; // enable compare event
PWM->PWM_CMP[2].PWM_CMPMUPD = 0x0001; // enable compare event
PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
break;
case 1: PWM->PWM_CMP[3].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current)); // update Z
PWM->PWM_CMP[3].PWM_CMPMUPD = 0x0001; // enable compare event
PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
break;
default:PWM->PWM_CMP[4].PWM_CMPVUPD = 0x010000000LL | G2_VREF_COUNT(G2_VREF(current)); // update E
PWM->PWM_CMP[4].PWM_CMPMUPD = 0x0001; // enable compare event
PWM->PWM_SCUC = PWM_SCUC_UPDULOCK; // tell the PWM controller to update the values on the next cycle
break;
}
}
volatile uint32_t PWM_ISR1_STATUS, PWM_ISR2_STATUS;
void PWM_Handler() {
PWM_ISR1_STATUS = PWM->PWM_ISR1;
PWM_ISR2_STATUS = PWM->PWM_ISR2;
if (PWM_ISR1_STATUS & PWM_IER1_CHID0) { // CHAN_0 interrupt
*ISR_table[0].set_register = ISR_table[0].write_mask; // set X to active
*ISR_table[1].set_register = ISR_table[1].write_mask; // set Y to active
*ISR_table[2].set_register = ISR_table[2].write_mask; // set Z to active
*ISR_table[3].set_register = ISR_table[3].write_mask; // set E to active
}
else {
if (PWM_ISR2_STATUS & PWM_IER2_CMPM1) *ISR_table[0].clr_register = ISR_table[0].write_mask; // set X to inactive
if (PWM_ISR2_STATUS & PWM_IER2_CMPM2) *ISR_table[1].clr_register = ISR_table[1].write_mask; // set Y to inactive
if (PWM_ISR2_STATUS & PWM_IER2_CMPM3) *ISR_table[2].clr_register = ISR_table[2].write_mask; // set Z to inactive
if (PWM_ISR2_STATUS & PWM_IER2_CMPM4) *ISR_table[3].clr_register = ISR_table[3].write_mask; // set E to inactive
}
return;
}
#endif // PRINTRBOARD_G2

77
Marlin/src/HAL/HAL_DUE/G2_PWM.h Normal file
View File

@ -0,0 +1,77 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* This module is stripped down version of the LPC1768_PWM.h file from
* PR #7500. It is hardwired for the PRINTRBOARD_G2 Motor Current needs.
*/
#include "../../inc/MarlinConfigPre.h"
#include "../../module/stepper.h"
//C:\Users\bobku\Documents\GitHub\Marlin-Bob-2\Marlin\src\module\stepper.h
//C:\Users\bobku\Documents\GitHub\Marlin-Bob-2\Marlin\src\HAL\HAL_DUE\G2_PWM.h
#define PWM_PERIOD_US 100 // base repetition rate in micro seconds
typedef struct { // holds the data needed by the ISR to control the Vref pin
volatile uint32_t* set_register;
volatile uint32_t* clr_register;
uint32_t write_mask;
} PWM_map;
#define G2_VREF(I) (uint32_t)(I * 5 * 0.15) // desired Vref * 1000 (scaled so don't loose accuracy in next step)
#define G2_VREF_COUNT(Q) (uint32_t)map(constrain(Q, 500, 3.3 * 1000), 0, 3.3 * 1000, 0, PWM_PERIOD_US) // under 500 the results are very non-linear
extern volatile uint32_t *SODR_A, *SODR_B, *CODR_A, *CODR_B;
#define _PIN(IO) (DIO ## IO ## _PIN)
#define PWM_MAP_INIT_ROW(IO,ZZ) { ZZ == 'A' ? SODR_A : SODR_B, ZZ == 'A' ? CODR_A : CODR_B, 1 << _PIN(IO) }
#define PWM_MAP_INIT { PWM_MAP_INIT_ROW(MOTOR_CURRENT_PWM_X_PIN, 'B'), \
PWM_MAP_INIT_ROW(MOTOR_CURRENT_PWM_Y_PIN, 'B'), \
PWM_MAP_INIT_ROW(MOTOR_CURRENT_PWM_Z_PIN, 'B'), \
PWM_MAP_INIT_ROW(MOTOR_CURRENT_PWM_E_PIN, 'A'), \
};
#define NUM_PWMS 4
extern PWM_map ISR_table[NUM_PWMS];
extern uint32_t motor_current_setting[3];
#define IR_BIT(p) (WITHIN(p, 0, 3) ? (p) : (p) + 4)
#define COPY_ACTIVE_TABLE() do{ for (uint8_t i = 0; i < 6 ; i++) work_table[i] = active_table[i]; }while(0)
#define PWM_MR0 19999 // base repetition rate minus one count - 20mS
#define PWM_PR 24 // prescaler value - prescaler divide by 24 + 1 - 1 MHz output
#define PWM_PCLKSEL0 0x00 // select clock source for prescaler - defaults to 25MHz on power up
// 0: 25MHz, 1: 100MHz, 2: 50MHz, 3: 12.5MHZ to PWM1 prescaler
#define MR0_MARGIN 200 // if channel value too close to MR0 the system locks up
extern bool PWM_table_swap; // flag to tell the ISR that the tables have been swapped
#define HAL_G2_PWM_ISR void PWM_Handler()
extern volatile uint32_t PWM_ISR1_STATUS, PWM_ISR2_STATUS;

278
Marlin/src/HAL/HAL_DUE/G2_pins.h Normal file
View File

@ -0,0 +1,278 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#pragma once
#include <stdint.h>
/**
* This file contains the custom port/pin definitions for the PRINTRBOARD_G2
* motherboard. This motherboard uses the SAM3X8C which is a subset of the
* SAM3X8E used in the DUE board. It uses port/pin pairs that are not
* available using the DUE definitions.
*
* The first part is a copy of the pin descriptions in the
* "variants\arduino_due_x\variant.cpp" file but with pins 34-41 replaced by
* the G2 pins.
*
* The second part is the FASTIO port/pin definitions.
*
* THESE PINS CAN ONLY BE ACCESSED VIA FASTIO COMMANDS.
*/
/*
Copyright (c) 2011 Arduino. All right reserved.
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
typedef struct _G2_PinDescription {
Pio* pPort;
uint32_t ulPin;
uint32_t ulPeripheralId;
EPioType ulPinType;
uint32_t ulPinConfiguration;
uint32_t ulPinAttribute;
EAnalogChannel ulAnalogChannel; /* Analog pin in the Arduino context (label on the board) */
EAnalogChannel ulADCChannelNumber; /* ADC Channel number in the SAM device */
EPWMChannel ulPWMChannel;
ETCChannel ulTCChannel;
} G2_PinDescription;
/**
* This section is a copy of the pin descriptions in the "variants\arduino_due_x\variant.cpp" file
* with pins 34-41 replaced by the G2 pins.
*/
/**
* Pins descriptions
*/
const G2_PinDescription G2_g_APinDescription[] = {
// 0 .. 53 - Digital pins
// ----------------------
// 0/1 - UART (Serial)
{ PIOA, PIO_PA8A_URXD, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // URXD
{ PIOA, PIO_PA9A_UTXD, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // UTXD
// 2
{ PIOB, PIO_PB25B_TIOA0, ID_PIOB, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC0_CHA0 }, // TIOA0
{ PIOC, PIO_PC28B_TIOA7, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHA7 }, // TIOA7
{ PIOC, PIO_PC26B_TIOB6, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHB6 }, // TIOB6
// 5
{ PIOC, PIO_PC25B_TIOA6, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHA6 }, // TIOA6
{ PIOC, PIO_PC24B_PWML7, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_PWM), NO_ADC, NO_ADC, PWM_CH7, NOT_ON_TIMER }, // PWML7
{ PIOC, PIO_PC23B_PWML6, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_PWM), NO_ADC, NO_ADC, PWM_CH6, NOT_ON_TIMER }, // PWML6
{ PIOC, PIO_PC22B_PWML5, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_PWM), NO_ADC, NO_ADC, PWM_CH5, NOT_ON_TIMER }, // PWML5
{ PIOC, PIO_PC21B_PWML4, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_PWM), NO_ADC, NO_ADC, PWM_CH4, NOT_ON_TIMER }, // PWML4
// 10
{ PIOC, PIO_PC29B_TIOB7, ID_PIOC, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHB7 }, // TIOB7
{ PIOD, PIO_PD7B_TIOA8, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHA8 }, // TIOA8
{ PIOD, PIO_PD8B_TIOB8, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC2_CHB8 }, // TIOB8
// 13 - AMBER LED
{ PIOB, PIO_PB27B_TIOB0, ID_PIOB, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_TIMER), NO_ADC, NO_ADC, NOT_ON_PWM, TC0_CHB0 }, // TIOB0
// 14/15 - USART3 (Serial3)
{ PIOD, PIO_PD4B_TXD3, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TXD3
{ PIOD, PIO_PD5B_RXD3, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // RXD3
// 16/17 - USART1 (Serial2)
{ PIOA, PIO_PA13A_TXD1, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TXD1
{ PIOA, PIO_PA12A_RXD1, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // RXD1
// 18/19 - USART0 (Serial1)
{ PIOA, PIO_PA11A_TXD0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TXD0
{ PIOA, PIO_PA10A_RXD0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // RXD0
// 20/21 - TWI1
{ PIOB, PIO_PB12A_TWD1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TWD1 - SDA0
{ PIOB, PIO_PB13A_TWCK1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TWCK1 - SCL0
// 22
{ PIOB, PIO_PB26, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 22
{ PIOA, PIO_PA14, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 23
{ PIOA, PIO_PA15, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 24
{ PIOD, PIO_PD0, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 25
// 26
{ PIOD, PIO_PD1, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 26
{ PIOD, PIO_PD2, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 27
{ PIOD, PIO_PD3, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 28
{ PIOD, PIO_PD6, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 29
// 30
{ PIOD, PIO_PD9, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 30
{ PIOA, PIO_PA7, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 31
{ PIOD, PIO_PD10, ID_PIOD, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 32
{ PIOC, PIO_PC1, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 33
// 34
// start of custom pins
{ PIOA, PIO_PA29, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 34 Y_STEP_PIN
{ PIOB, PIO_PB1, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 35 Y_DIR_PIN
{ PIOB, PIO_PB0, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 36 Y_ENABLE_PIN
{ PIOB, PIO_PB22, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 37 E0_ENABLE_PIN
{ PIOB, PIO_PB11, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 38 E0_MS1_PIN
{ PIOB, PIO_PB10, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 39 E0_MS3_PIN
{ PIOA, PIO_PA5, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 40 HEATER_0_PIN
{ PIOB, PIO_PB24, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 41 HEATER_BED_PIN
// end of custom pins
// 42
{ PIOA, PIO_PA19, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 42
{ PIOA, PIO_PA20, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 43
{ PIOC, PIO_PC19, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 44
{ PIOC, PIO_PC18, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 45
// 46
{ PIOC, PIO_PC17, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 46
{ PIOC, PIO_PC16, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 47
{ PIOC, PIO_PC15, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 48
{ PIOC, PIO_PC14, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 49
// 50
{ PIOC, PIO_PC13, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 50
{ PIOC, PIO_PC12, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 51
{ PIOB, PIO_PB21, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 52
{ PIOB, PIO_PB14, ID_PIOB, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // PIN 53
// 54 .. 65 - Analog pins
// ----------------------
{ PIOA, PIO_PA16X1_AD7, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC0, ADC7, NOT_ON_PWM, NOT_ON_TIMER }, // AD0
{ PIOA, PIO_PA24X1_AD6, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC1, ADC6, NOT_ON_PWM, NOT_ON_TIMER }, // AD1
{ PIOA, PIO_PA23X1_AD5, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC2, ADC5, NOT_ON_PWM, NOT_ON_TIMER }, // AD2
{ PIOA, PIO_PA22X1_AD4, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC3, ADC4, NOT_ON_PWM, NOT_ON_TIMER }, // AD3
// 58
{ PIOA, PIO_PA6X1_AD3, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC4, ADC3, NOT_ON_PWM, TC0_CHB2 }, // AD4
{ PIOA, PIO_PA4X1_AD2, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC5, ADC2, NOT_ON_PWM, NOT_ON_TIMER }, // AD5
{ PIOA, PIO_PA3X1_AD1, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC6, ADC1, NOT_ON_PWM, TC0_CHB1 }, // AD6
{ PIOA, PIO_PA2X1_AD0, ID_PIOA, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC7, ADC0, NOT_ON_PWM, TC0_CHA1 }, // AD7
// 62
{ PIOB, PIO_PB17X1_AD10, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC8, ADC10, NOT_ON_PWM, NOT_ON_TIMER }, // AD8
{ PIOB, PIO_PB18X1_AD11, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC9, ADC11, NOT_ON_PWM, NOT_ON_TIMER }, // AD9
{ PIOB, PIO_PB19X1_AD12, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC10, ADC12, NOT_ON_PWM, NOT_ON_TIMER }, // AD10
{ PIOB, PIO_PB20X1_AD13, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC11, ADC13, NOT_ON_PWM, NOT_ON_TIMER }, // AD11
// 66/67 - DAC0/DAC1
{ PIOB, PIO_PB15X1_DAC0, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC12, DA0, NOT_ON_PWM, NOT_ON_TIMER }, // DAC0
{ PIOB, PIO_PB16X1_DAC1, ID_PIOB, PIO_INPUT, PIO_DEFAULT, PIN_ATTR_ANALOG, ADC13, DA1, NOT_ON_PWM, NOT_ON_TIMER }, // DAC1
// 68/69 - CANRX0/CANTX0
{ PIOA, PIO_PA1A_CANRX0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, ADC14, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // CANRX
{ PIOA, PIO_PA0A_CANTX0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, ADC15, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // CANTX
// 70/71 - TWI0
{ PIOA, PIO_PA17A_TWD0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TWD0 - SDA1
{ PIOA, PIO_PA18A_TWCK0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // TWCK0 - SCL1
// 72/73 - LEDs
{ PIOC, PIO_PC30, ID_PIOC, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // LED AMBER RXL
{ PIOA, PIO_PA21, ID_PIOA, PIO_OUTPUT_0, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // LED AMBER TXL
// 74/75/76 - SPI
{ PIOA, PIO_PA25A_SPI0_MISO,ID_PIOA,PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // MISO
{ PIOA, PIO_PA26A_SPI0_MOSI,ID_PIOA,PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // MOSI
{ PIOA, PIO_PA27A_SPI0_SPCK,ID_PIOA,PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // SPCK
// 77 - SPI CS0
{ PIOA, PIO_PA28A_SPI0_NPCS0,ID_PIOA,PIO_PERIPH_A,PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // NPCS0
// 78 - SPI CS3 (unconnected)
{ PIOB, PIO_PB23B_SPI0_NPCS3,ID_PIOB,PIO_PERIPH_B,PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // NPCS3
// 79 .. 84 - "All pins" masks
// 79 - TWI0 all pins
{ PIOA, PIO_PA17A_TWD0|PIO_PA18A_TWCK0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER },
// 80 - TWI1 all pins
{ PIOB, PIO_PB12A_TWD1|PIO_PB13A_TWCK1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER },
// 81 - UART (Serial) all pins
{ PIOA, PIO_PA8A_URXD|PIO_PA9A_UTXD, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER },
// 82 - USART0 (Serial1) all pins
{ PIOA, PIO_PA11A_TXD0|PIO_PA10A_RXD0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER },
// 83 - USART1 (Serial2) all pins
{ PIOA, PIO_PA13A_TXD1|PIO_PA12A_RXD1, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER },
// 84 - USART3 (Serial3) all pins
{ PIOD, PIO_PD4B_TXD3|PIO_PD5B_RXD3, ID_PIOD, PIO_PERIPH_B, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER },
// 85 - USB
{ PIOB, PIO_PB11A_UOTGID|PIO_PB10A_UOTGVBOF, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL,NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // ID - VBOF
// 86 - SPI CS2
{ PIOB, PIO_PB21B_SPI0_NPCS2, ID_PIOB, PIO_PERIPH_B, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // NPCS2
// 87 - SPI CS1
{ PIOA, PIO_PA29A_SPI0_NPCS1, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // NPCS1
// 88/89 - CANRX1/CANTX1 (same physical pin for 66/53)
{ PIOB, PIO_PB15A_CANRX1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // CANRX1
{ PIOB, PIO_PB14A_CANTX1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, PIN_ATTR_DIGITAL, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }, // CANTX1
// 90 .. 91 - "All CAN pins" masks
// 90 - CAN0 all pins
{ PIOA, PIO_PA1A_CANRX0|PIO_PA0A_CANTX0, ID_PIOA, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER },
// 91 - CAN1 all pins
{ PIOB, PIO_PB15A_CANRX1|PIO_PB14A_CANTX1, ID_PIOB, PIO_PERIPH_A, PIO_DEFAULT, (PIN_ATTR_DIGITAL|PIN_ATTR_COMBO), NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER },
// END
{ NULL, 0, 0, PIO_NOT_A_PIN, PIO_DEFAULT, 0, NO_ADC, NO_ADC, NOT_ON_PWM, NOT_ON_TIMER }
};
// This section replaces the FASTIO definitions of pins 34-41
#define DIO34_PIN 29
#define DIO34_WPORT PIOA // only available via FASTIO // 34 PA29 - Y_STEP_PIN
#define DIO35_PIN 1
#define DIO35_WPORT PIOB // only available via FASTIO // 35 PAB1 - Y_DIR_PIN
#define DIO36_PIN 0
#define DIO36_WPORT PIOB // only available via FASTIO // 36 PB0 - Y_ENABLE_PIN
#define DIO37_PIN 22
#define DIO37_WPORT PIOB // only available via FASTIO // 37 PB22 - E0_ENABLE_PIN
#define DIO38_PIN 11
#define DIO38_WPORT PIOB // only available via FASTIO // 38 PB11 - E0_MS1_PIN
#define DIO39_PIN 10
#define DIO39_WPORT PIOB // only available via FASTIO // 39 PB10 - E0_MS3_PIN
#define DIO40_PIN 5
#define DIO40_WPORT PIOA // only available via FASTIO // 40 PA5 - HEATER_0_PIN
#define DIO41_PIN 24
#define DIO41_WPORT PIOB // only available via FASTIO // 41 PB24 - HEATER_BED_PIN

131
Marlin/src/HAL/HAL_DUE/fastio_Due.h
View File

@ -65,7 +65,7 @@
// Write to a pin
#define _WRITE_VAR(IO,V) do { \
volatile Pio* port = digitalPinToPort(IO); \
uint32_t mask = digitalPinToBitMask(IO); \
const uint32_t mask = digitalPinToBitMask(IO); \
if (V) port->PIO_SODR = mask; \
else port->PIO_CODR = mask; \
} while(0)
@ -73,7 +73,7 @@
// Write to a pin
#define _WRITE(IO,V) do { \
volatile Pio* port = (DIO ## IO ## _WPORT); \
uint32_t mask = MASK(DIO ## IO ## _PIN); \
const uint32_t mask = MASK(DIO ## IO ## _PIN); \
if (V) port->PIO_SODR = mask; \
else port->PIO_CODR = mask; \
} while(0)
@ -81,18 +81,79 @@
// Toggle a pin
#define _TOGGLE(IO) _WRITE(IO, !READ(IO))
// Set pin as input
#define _SET_INPUT(IO) do{ \
pmc_enable_periph_clk(g_APinDescription[IO].ulPeripheralId); \
PIO_Configure(digitalPinToPort(IO), PIO_INPUT, digitalPinToBitMask(IO), 0); \
}while(0)
#include <pins_arduino.h>
// Set pin as output
#define _SET_OUTPUT(IO) do{ \
pmc_enable_periph_clk(g_APinDescription[IO].ulPeripheralId); \
PIO_Configure(digitalPinToPort(IO), _READ(IO) ? PIO_OUTPUT_1 : PIO_OUTPUT_0, digitalPinToBitMask(IO), g_APinDescription[IO].ulPinConfiguration); \
g_pinStatus[IO] = (g_pinStatus[IO] & 0xF0) | PIN_STATUS_DIGITAL_OUTPUT;\
}while(0)
#if MB(PRINTRBOARD_G2)
#include "G2_pins.h"
// Set pin as input
#define _SET_INPUT(IO) do{ \
pmc_enable_periph_clk(G2_g_APinDescription[IO].ulPeripheralId); \
PIO_Configure((DIO ## IO ## _WPORT), PIO_INPUT, MASK(DIO ## IO ## _PIN), 0); \
}while(0)
// Set pin as output
#define _SET_OUTPUT(IO) do{ \
uint32_t mask = MASK(G2_g_APinDescription[IO].ulPeripheralId); \
if ((PMC->PMC_PCSR0 & mask) != (mask)) PMC->PMC_PCER0 = mask; \
volatile Pio* port = (DIO ## IO ## _WPORT); \
mask = MASK(DIO ## IO ## _PIN); \
if (_READ(IO)) port->PIO_SODR = mask; \
else port->PIO_CODR = mask; \
port->PIO_IDR = mask; \
const uint32_t pin_config = G2_g_APinDescription[IO].ulPinConfiguration; \
if (pin_config & PIO_PULLUP) port->PIO_PUER = mask; \
else port->PIO_PUDR = mask; \
if (pin_config & PIO_OPENDRAIN) port->PIO_MDER = mask; \
else port->PIO_MDDR = mask; \
port->PIO_PER = mask; \
port->PIO_OER = mask; \
g_pinStatus[IO] = (g_pinStatus[IO] & 0xF0) | PIN_STATUS_DIGITAL_OUTPUT; \
}while(0)
/**
* Set pin as output with comments
* #define _SET_OUTPUT(IO) do{ \
* uint32_t mask = MASK(G2_g_APinDescription[IO].ulPeripheralId); \
* if ((PMC->PMC_PCSR0 & mask ) != (mask)) PMC->PMC_PCER0 = mask; \ // enable PIO clock if not already enabled
*
* volatile Pio* port = (DIO ## IO ## _WPORT); \
* const uint32_t mask = MASK(DIO ## IO ## _PIN); \
* if (_READ(IO)) port->PIO_SODR = mask; \ // set output to match input BEFORE setting direction or will glitch the output
* else port->PIO_CODR = mask; \
*
* port->PIO_IDR = mask; \ // disable interrupt
*
* uint32_t pin_config = G2_g_APinDescription[IO].ulPinConfiguration; \
* if (pin_config & PIO_PULLUP) pPio->PIO_PUER = mask; \ // enable pullup if necessary
* else pPio->PIO_PUDR = mask; \
*
* if (pin_config & PIO_OPENDRAIN) port->PIO_MDER = mask; \ // Enable multi-drive if necessary
* else port->PIO_MDDR = mask; \
*
* port->PIO_PER = mask; \
* port->PIO_OER = mask; \ // set to output
*
* g_pinStatus[IO] = (g_pinStatus[IO] & 0xF0) | PIN_STATUS_DIGITAL_OUTPUT; \
* }while(0)
*/
#else
// Set pin as input
#define _SET_INPUT(IO) do{ \
pmc_enable_periph_clk(g_APinDescription[IO].ulPeripheralId); \
PIO_Configure(digitalPinToPort(IO), PIO_INPUT, digitalPinToBitMask(IO), 0); \
}while(0)
// Set pin as output
#define _SET_OUTPUT(IO) do{ \
pmc_enable_periph_clk(g_APinDescription[IO].ulPeripheralId); \
PIO_Configure(digitalPinToPort(IO), _READ(IO) ? PIO_OUTPUT_1 : PIO_OUTPUT_0, digitalPinToBitMask(IO), g_APinDescription[IO].ulPinConfiguration); \
g_pinStatus[IO] = (g_pinStatus[IO] & 0xF0) | PIN_STATUS_DIGITAL_OUTPUT; \
}while(0)
#endif
// Set pin as input with pullup mode
#define _PULLUP(IO,V) pinMode(IO, (V) ? INPUT_PULLUP : INPUT)
@ -243,29 +304,33 @@
#define DIO33_PIN 1
#define DIO33_WPORT PIOC
#define DIO34_PIN 2
#define DIO34_WPORT PIOC
#if !MB(PRINTRBOARD_G2) // normal DUE pin mapping
#define DIO35_PIN 3
#define DIO35_WPORT PIOC
#define DIO34_PIN 2
#define DIO34_WPORT PIOC
#define DIO36_PIN 4
#define DIO36_WPORT PIOC
#define DIO35_PIN 3
#define DIO35_WPORT PIOC
#define DIO37_PIN 5
#define DIO37_WPORT PIOC
#define DIO36_PIN 4
#define DIO36_WPORT PIOC
#define DIO38_PIN 6
#define DIO38_WPORT PIOC
#define DIO37_PIN 5
#define DIO37_WPORT PIOC
#define DIO39_PIN 7
#define DIO39_WPORT PIOC
#define DIO38_PIN 6
#define DIO38_WPORT PIOC
#define DIO40_PIN 8
#define DIO40_WPORT PIOC
#define DIO39_PIN 7
#define DIO39_WPORT PIOC
#define DIO41_PIN 9
#define DIO41_WPORT PIOC
#define DIO40_PIN 8
#define DIO40_WPORT PIOC
#define DIO41_PIN 9
#define DIO41_WPORT PIOC
#endif // !PRINTRBOARD_G2
#define DIO42_PIN 19
#define DIO42_WPORT PIOA
@ -418,6 +483,7 @@
#define DIO91_WPORT PIOB
#if ARDUINO_SAM_ARCHIM
#define DIO92_PIN 11
#define DIO92_WPORT PIOC
@ -468,7 +534,9 @@
#define DIO108_PIN 9
#define DIO108_WPORT PIOB
#else
#else // !ARDUINO_SAM_ARCHIM
#define DIO92_PIN 5
#define DIO92_WPORT PIOA
@ -495,4 +563,5 @@
#define DIO100_PIN 11
#define DIO100_WPORT PIOC
#endif
#endif // !ARDUINO_SAM_ARCHIM