Split the configuration file in two parts.

One for common settings.
One for advanced settings.
This commit is contained in:
Erik van der Zalm 2012-02-07 20:23:43 +01:00
parent f9c5333f97
commit d8a0c6450f
3 changed files with 257 additions and 246 deletions

View File

@ -1,26 +1,13 @@
#ifndef __CONFIGURATION_H #ifndef __CONFIGURATION_H
#define __CONFIGURATION_H #define __CONFIGURATION_H
// This configurtion file contains the basic settings.
// Advanced settings can be found in Configuration_adv.h
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
// This determines the communication speed of the printer // This determines the communication speed of the printer
#define BAUDRATE 250000 #define BAUDRATE 250000
//#define BAUDRATE 115200 //#define BAUDRATE 115200
//#define BAUDRATE 230400
#define EXTRUDERS 1
// Frequency limit
// See nophead's blog for more info
// Not working O
//#define XY_FREQUENCY_LIMIT 15
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
// of the buffer and all stops. This should not be much greater than zero and should only be changed
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
#define MINIMUM_PLANNER_SPEED 2.0 // (mm/sec)
// BASIC SETTINGS: select your board type, thermistor type, axis scaling, and endstop configuration
//// The following define selects which electronics board you have. Please choose the one that matches your setup //// The following define selects which electronics board you have. Please choose the one that matches your setup
// MEGA/RAMPS up to 1.2 = 3, // MEGA/RAMPS up to 1.2 = 3,
@ -36,7 +23,10 @@
//=============================Thermal Settings ============================ //=============================Thermal Settings ============================
//=========================================================================== //===========================================================================
//// Thermistor settings: //// Temperature sensor settings:
// -2 is thermocouple with MAX6675 (only for sensor 0)
// -1 is thermocouple with AD595
// 0 is not used
// 1 is 100k thermistor // 1 is 100k thermistor
// 2 is 200k thermistor // 2 is 200k thermistor
// 3 is mendel-parts thermistor // 3 is mendel-parts thermistor
@ -45,70 +35,33 @@
// 6 is EPCOS 100k // 6 is EPCOS 100k
// 7 is 100k Honeywell thermistor 135-104LAG-J01 // 7 is 100k Honeywell thermistor 135-104LAG-J01
//#define THERMISTORHEATER_0 3 #define TEMP_SENSOR_0 -1
//#define THERMISTORHEATER_1 1 #define TEMP_SENSOR_1 0
//#define THERMISTORHEATER_2 1 #define TEMP_SENSOR_2 0
#define TEMP_SENSOR_BED 0
//#define HEATER_0_USES_THERMISTOR
//#define HEATER_1_USES_THERMISTOR
//#define HEATER_2_USES_THERMISTOR
#define HEATER_0_USES_AD595
//#define HEATER_1_USES_AD595
//#define HEATER_2_USES_AD595
//#define HEATER_0_USES_MAX6675
// Select one of these only to define how the bed temp is read.
//#define THERMISTORBED 1
//#define BED_USES_THERMISTOR
//#define BED_LIMIT_SWITCHING
#ifdef BED_LIMIT_SWITCHING
#define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
#endif
//#define BED_USES_AD595
#define BED_CHECK_INTERVAL 5000 //ms
//// Heating sanity check:
// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109
//#define WATCHPERIOD 20000 //20 seconds
// Actual temperature must be close to target for this long before M109 returns success // Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 30 // (seconds) #define TEMP_RESIDENCY_TIME 30 // (seconds)
#define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one
//// The minimal temperature defines the temperature below which the heater will not be enabled // The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time.
#define HEATER_0_MINTEMP 5 #define HEATER_0_MINTEMP 5
//#define HEATER_1_MINTEMP 5 #define HEATER_1_MINTEMP 5
//#define HEATER_2_MINTEMP 5 #define HEATER_2_MINTEMP 5
//#define BED_MINTEMP 5 #define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection. // You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
//#define HEATER_1_MAXTEMP 275 #define HEATER_1_MAXTEMP 275
//#define HEATER_2_MAXTEMP 275 #define HEATER_2_MAXTEMP 275
//#define BED_MAXTEMP 150 #define BED_MAXTEMP 150
// Wait for Cooldown
// This defines if the M109 call should not block if it is cooling down.
// example: From a current temp of 220, you set M109 S200.
// if CooldownNoWait is defined M109 will not wait for the cooldown to finish
#define CooldownNoWait true
// Heating is finished if a temperature close to this degree shift is reached
#define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree
//Do not wait for M109 to finish when printing from SD card
//#define STOP_HEATING_WAIT_WHEN_SD_PRINTING
// PID settings: // PID settings:
// Uncomment the following line to enable PID support. // Comment the following line to disable PID and enable bang-bang.
#define PIDTEMP #define PIDTEMP
#define PID_MAX 255 // limits current to nozzle; 255=full current #define PID_MAX 255 // limits current to nozzle; 255=full current
#ifdef PIDTEMP #ifdef PIDTEMP
@ -118,28 +71,8 @@
#define K1 0.95 //smoothing factor withing the PID #define K1 0.95 //smoothing factor withing the PID
#define PID_dT 0.128 //sampling period of the PID #define PID_dT 0.128 //sampling period of the PID
//To develop some PID settings for your machine, you can initiall follow // If you are using a preconfigured hotend then you can use one of the value sets by uncommenting it
// the Ziegler-Nichols method. // Ultimaker
// set Ki and Kd to zero.
// heat with a defined Kp and see if the temperature stabilizes
// ideally you do this graphically with repg.
// the PID_CRITIAL_GAIN should be the Kp at which temperature oscillatins are not dampned out/decreas in amplitutde
// PID_SWING_AT_CRITIAL is the time for a full period of the oscillations at the critical Gain
// usually further manual tunine is necessary.
#define PID_CRITIAL_GAIN 50
#define PID_SWING_AT_CRITIAL 47 //seconds
//#define PID_PI //no differentail term
#define PID_PID //normal PID
#ifdef PID_PID
//PID according to Ziegler-Nichols method
// #define DEFAULT_Kp (0.6*PID_CRITIAL_GAIN)
// #define DEFAULT_Ki (2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
// #define DEFAULT_Kd (PID_SWING_AT_CRITIAL/8./PID_dT)
// Ultitmaker
#define DEFAULT_Kp 22.2 #define DEFAULT_Kp 22.2
#define DEFAULT_Ki (1.25*PID_dT) #define DEFAULT_Ki (1.25*PID_dT)
#define DEFAULT_Kd (99/PID_dT) #define DEFAULT_Kd (99/PID_dT)
@ -153,38 +86,18 @@
// #define DEFAULT_Kp 63.0 // #define DEFAULT_Kp 63.0
// #define DEFAULT_Ki (2.25*PID_dT) // #define DEFAULT_Ki (2.25*PID_dT)
// #define DEFAULT_Kd (440/PID_dT) // #define DEFAULT_Kd (440/PID_dT)
#endif
#ifdef PID_PI
//PI according to Ziegler-Nichols method
#define DEFAULT_Kp (PID_CRITIAL_GAIN/2.2)
#define DEFAULT_Ki (1.2*Kp/PID_SWING_AT_CRITIAL*PID_dT)
#define DEFAULT_Kd (0)
#endif
// this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
// if Kc is choosen well, the additional required power due to increased melting should be compensated.
#define PID_ADD_EXTRUSION_RATE
#ifdef PID_ADD_EXTRUSION_RATE
#define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed)
#endif
#endif // PIDTEMP #endif // PIDTEMP
// extruder run-out prevention. //this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded //can be software-disabled for whatever purposes by
//#define EXTRUDER_RUNOUT_PREVENT #define PREVENT_DANGEROUS_EXTRUDE
#define EXTRUDER_RUNOUT_MINTEMP 190 #define EXTRUDE_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30. #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
//=========================================================================== //===========================================================================
//=============================Mechanical Settings=========================== //=============================Mechanical Settings===========================
//=========================================================================== //===========================================================================
// Endstop Settings // Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
@ -192,9 +105,6 @@
const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0 #define X_ENABLE_ON 0
@ -207,13 +117,6 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define DISABLE_Y false #define DISABLE_Y false
#define DISABLE_Z false #define DISABLE_Z false
#define DISABLE_E false // For all extruders #define DISABLE_E false // For all extruders
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
// Inverting axis direction
//#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true
//#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false
//#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
//#define INVERT_E*_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false, used for all extruders
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true #define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false #define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
@ -222,7 +125,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
//// ENDSTOP SETTINGS: // ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN // Sets direction of endstops when homing; 1=MAX, -1=MIN
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
@ -238,43 +141,19 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) #define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min)
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
#define X_HOME_RETRACT_MM 5
#define Y_HOME_RETRACT_MM 5
#define Z_HOME_RETRACT_MM 1
#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
#define AXIS_RELATIVE_MODES {false, false, false, false}
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
// default settings // default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker #define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker
//#define DEFAULT_AXIS_STEPS_PER_UNIT {40, 40, 3333.92, 360} //sells mendel with v9 extruder
//#define DEFAULT_AXIS_STEPS_PER_UNIT {80.3232, 80.8900, 2284.7651, 757.2218} // SAE Prusa w/ Wade extruder
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) #define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate //
#define DEFAULT_MINTRAVELFEEDRATE 0.0
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
#define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this
#define DEFAULT_XYJERK 20.0 // (mm/sec) #define DEFAULT_XYJERK 20.0 // (mm/sec)
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_ZJERK 0.4 // (mm/sec)
// If defined the movements slow down when the look ahead buffer is only half full
#define SLOWDOWN
//default stepper release if idle
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
#define DEFAULT_STEPPER_DEACTIVE_COMMAND "M84 X Y E" //z stays powered
//=========================================================================== //===========================================================================
//=============================Additional Features=========================== //=============================Additional Features===========================
//=========================================================================== //===========================================================================
@ -285,47 +164,14 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. // M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
//define this to enable eeprom support //define this to enable eeprom support
#define EEPROM_SETTINGS //#define EEPROM_SETTINGS
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: //to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
// please keep turned on if you can. // please keep turned on if you can.
#define EEPROM_CHITCHAT //#define EEPROM_CHITCHAT
// The hardware watchdog should halt the Microcontroller, in case the firmware gets stuck somewhere. However:
// the Watchdog is not working well, so please only enable this for testing
// this enables the watchdog interrupt.
//#define USE_WATCHDOG
//#ifdef USE_WATCHDOG
// you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
//#define RESET_MANUAL
//#define WATCHDOG_TIMEOUT 4 //seconds
//#endif
// extruder advance constant (s2/mm3)
//
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
//
// hooke's law says: force = k * distance
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
// so: v ^ 2 is proportional to number of steps we advance the extruder
//#define ADVANCE
#ifdef ADVANCE
#define EXTRUDER_ADVANCE_K .0
#define D_FILAMENT 2.85
#define STEPS_MM_E 836
#define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
#endif // ADVANCE
//LCD and SD support //LCD and SD support
//#define ULTRA_LCD //general lcd support, also 16x2 //#define ULTRA_LCD //general lcd support, also 16x2
//#define SDSUPPORT // Enable SD Card Support in Hardware Console //#define SDSUPPORT // Enable SD Card Support in Hardware Console
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
//#define ULTIPANEL //#define ULTIPANEL
#ifdef ULTIPANEL #ifdef ULTIPANEL
@ -341,60 +187,11 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#endif #endif
#endif #endif
// A debugging feature to compare calculated vs performed steps, to see if steps are lost by the software.
//#define DEBUG_STEPS
// Arc interpretation settings:
#define MM_PER_ARC_SEGMENT 1
#define N_ARC_CORRECTION 25
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
//The maximum buffered steps/sec of the extruder motor are called "se".
//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
// you exit the value by any M109 without F*
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
// on an ultimaker, some initial testing worked with M109 S215 T260 F0.1 in the start.gcode
//#define AUTOTEMP
#ifdef AUTOTEMP
#define AUTOTEMP_OLDWEIGHT 0.98
#endif
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//can be software-disabled for whatever purposes by
#define PREVENT_DANGEROUS_EXTRUDE
#define EXTRUDE_MINTEMP 190
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
// M240 Triggers a camera by emulating a Canon RC-1 Remote // M240 Triggers a camera by emulating a Canon RC-1 Remote
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ // Data from: http://www.doc-diy.net/photo/rc-1_hacked/
// #define PHOTOGRAPH_PIN 23 // #define PHOTOGRAPH_PIN 23
//=========================================================================== #include "Configuration_adv.h"
//=============================Buffers ============================
//===========================================================================
// The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
#if defined SDSUPPORT
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
#endif
//The ASCII buffer for recieving from the serial:
#define MAX_CMD_SIZE 96
#define BUFSIZE 4
#include "thermistortables.h" #include "thermistortables.h"
#endif //__CONFIGURATION_H #endif //__CONFIGURATION_H

208
Marlin/Configuration_adv.h Normal file
View File

@ -0,0 +1,208 @@
#ifndef __CONFIGURATION_ADV_H
#define __CONFIGURATION_ADV_H
//===========================================================================
//=============================Thermal Settings ============================
//===========================================================================
// Select one of these only to define how the bed temp is read.
//
//#define BED_LIMIT_SWITCHING
#ifdef BED_LIMIT_SWITCHING
#define BED_HYSTERESIS 2 //only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
#endif
#define BED_CHECK_INTERVAL 5000 //ms
//// Heating sanity check:
// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109
//#define WATCHPERIOD 20000 //20 seconds
// Wait for Cooldown
// This defines if the M109 call should not block if it is cooling down.
// example: From a current temp of 220, you set M109 S200.
// if CooldownNoWait is defined M109 will not wait for the cooldown to finish
#define CooldownNoWait true
// Heating is finished if a temperature close to this degree shift is reached
#define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree
//Do not wait for M109 to finish when printing from SD card
//#define STOP_HEATING_WAIT_WHEN_SD_PRINTING
#ifdef PIDTEMP
// this adds an experimental additional term to the heatingpower, proportional to the extrusion speed.
// if Kc is choosen well, the additional required power due to increased melting should be compensated.
#define PID_ADD_EXTRUSION_RATE
#ifdef PID_ADD_EXTRUSION_RATE
#define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed)
#endif
#endif
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
//The maximum buffered steps/sec of the extruder motor are called "se".
//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
// you exit the value by any M109 without F*
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
// on an ultimaker, some initial testing worked with M109 S215 T260 F0.1 in the start.gcode
//#define AUTOTEMP
#ifdef AUTOTEMP
#define AUTOTEMP_OLDWEIGHT 0.98
#endif
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30.
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
//===========================================================================
//=============================Mechanical Settings===========================
//===========================================================================
// This defines the number of extruders
#define EXTRUDERS 1
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
#define X_HOME_RETRACT_MM 5
#define Y_HOME_RETRACT_MM 5
#define Z_HOME_RETRACT_MM 1
#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
#define AXIS_RELATIVE_MODES {false, false, false, false}
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
//default stepper release if idle
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
#define DEFAULT_STEPPER_DEACTIVE_COMMAND "M84 X Y E" //z stays powered
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
#define DEFAULT_MINTRAVELFEEDRATE 0.0
// minimum time in microseconds that a movement needs to take if the buffer is emptied. Increase this number if you see blobs while printing high speed & high detail. It will slowdown on the detailed stuff.
#define DEFAULT_MINSEGMENTTIME 20000 // Obsolete delete this
// If defined the movements slow down when the look ahead buffer is only half full
#define SLOWDOWN
// Frequency limit
// See nophead's blog for more info
// Not working O
//#define XY_FREQUENCY_LIMIT 15
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
// of the buffer and all stops. This should not be much greater than zero and should only be changed
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
#define MINIMUM_PLANNER_SPEED 2.0 // (mm/sec)
//===========================================================================
//=============================Additional Features===========================
//===========================================================================
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
// The hardware watchdog should halt the Microcontroller, in case the firmware gets stuck somewhere. However:
// the Watchdog is not working well, so please only enable this for testing
// this enables the watchdog interrupt.
//#define USE_WATCHDOG
//#ifdef USE_WATCHDOG
// you cannot reboot on a mega2560 due to a bug in he bootloader. Hence, you have to reset manually, and this is done hereby:
//#define RESET_MANUAL
//#define WATCHDOG_TIMEOUT 4 //seconds
//#endif
// extruder advance constant (s2/mm3)
//
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
//
// hooke's law says: force = k * distance
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
// so: v ^ 2 is proportional to number of steps we advance the extruder
//#define ADVANCE
#ifdef ADVANCE
#define EXTRUDER_ADVANCE_K .0
#define D_FILAMENT 2.85
#define STEPS_MM_E 836
#define EXTRUTION_AREA (0.25 * D_FILAMENT * D_FILAMENT * 3.14159)
#define STEPS_PER_CUBIC_MM_E (axis_steps_per_unit[E_AXIS]/ EXTRUTION_AREA)
#endif // ADVANCE
// A debugging feature to compare calculated vs performed steps, to see if steps are lost by the software.
//#define DEBUG_STEPS
// Arc interpretation settings:
#define MM_PER_ARC_SEGMENT 1
#define N_ARC_CORRECTION 25
const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
//===========================================================================
//=============================Buffers ============================
//===========================================================================
// The number of linear motions that can be in the plan at any give time.
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ringbuffering.
#if defined SDSUPPORT
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
#else
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
#endif
//The ASCII buffer for recieving from the serial:
#define MAX_CMD_SIZE 96
#define BUFSIZE 4
//===========================================================================
//============================= Define Defines ============================
//===========================================================================
#if TEMP_SENSOR_0 > 0
#define THERMISTORHEATER_0 TEMP_SENSOR_0
#define HEATER_0_USES_THERMISTOR
#endif
#if TEMP_SENSOR_1 > 0
#define THERMISTORHEATER_1 TEMP_SENSOR_1
#define HEATER_1_USES_THERMISTOR
#endif
#if TEMP_SENSOR_2 > 0
#define THERMISTORHEATER_2 TEMP_SENSOR_2
#define HEATER_2_USES_THERMISTOR
#endif
#if TEMP_SENSOR_BED > 0
#define THERMISTORBED TEMP_SENSOR_BED
#define BED_USES_THERMISTOR
#endif
#if TEMP_SENSOR_0 == -1
#define HEATER_0_USES_AD595
#endif
#if TEMP_SENSOR_1 == -1
#define HEATER_1_USES_AD595
#endif
#if TEMP_SENSOR_2 == -1
#define HEATER_2_USES_AD595
#endif
#if TEMP_SENSOR_BED == -1
#define BED_USES_AD595
#endif
#if TEMP_SENSOR_0 == -2
#define HEATER_0_USES_MAX6675
#endif
#endif //__CONFIGURATION_ADV_H

View File

@ -254,6 +254,12 @@ void suicide()
#endif #endif
} }
long millis_diff(unsigned long starttime) {
unsigned long difftime = millis() - starttime;
if (difftime > 0x8000) difftime += 0x8000;
return difftime;
}
void setup() void setup()
{ {
setup_powerhold(); setup_powerhold();
@ -550,9 +556,9 @@ void process_commands()
if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait
st_synchronize(); st_synchronize();
codenum += millis(); // keep track of when we started waiting // codenum += millis(); // keep track of when we started waiting
previous_millis_cmd = millis(); previous_millis_cmd = millis();
while(millis() < codenum ){ while(millis_diff(previous_millis_cmd) < codenum ){
manage_heater(); manage_heater();
} }
break; break;
@ -843,11 +849,11 @@ void process_commands()
/* continue to loop until we have reached the target temp /* continue to loop until we have reached the target temp
_and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */ _and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */
while((residencyStart == -1) || while((residencyStart == -1) ||
(residencyStart > -1 && (millis() - residencyStart) < TEMP_RESIDENCY_TIME*1000) ) { (residencyStart > -1 && (millis_diff(residencyStart) < TEMP_RESIDENCY_TIME*1000) )) {
#else #else
while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) { while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) {
#endif //TEMP_RESIDENCY_TIME #endif //TEMP_RESIDENCY_TIME
if( (millis() - codenum) > 1000 ) if(millis_diff(codenum) > 1000 )
{ //Print Temp Reading and remaining time every 1 second while heating up/cooling down { //Print Temp Reading and remaining time every 1 second while heating up/cooling down
SERIAL_PROTOCOLPGM("T:"); SERIAL_PROTOCOLPGM("T:");
SERIAL_PROTOCOL( degHotend(tmp_extruder) ); SERIAL_PROTOCOL( degHotend(tmp_extruder) );
@ -857,7 +863,7 @@ void process_commands()
SERIAL_PROTOCOLPGM(" W:"); SERIAL_PROTOCOLPGM(" W:");
if(residencyStart > -1) if(residencyStart > -1)
{ {
codenum = TEMP_RESIDENCY_TIME - ((millis() - residencyStart) / 1000); codenum = TEMP_RESIDENCY_TIME - (millis_diff(residencyStart) / 1000);
SERIAL_PROTOCOLLN( codenum ); SERIAL_PROTOCOLLN( codenum );
} }
else else
@ -895,7 +901,7 @@ void process_commands()
codenum = millis(); codenum = millis();
while(isHeatingBed()) while(isHeatingBed())
{ {
if( (millis()-codenum) > 1000 ) //Print Temp Reading every 1 second while heating up. if( millis_diff(codenum) > 1000 ) //Print Temp Reading every 1 second while heating up.
{ {
float tt=degHotend(active_extruder); float tt=degHotend(active_extruder);
SERIAL_PROTOCOLPGM("T:"); SERIAL_PROTOCOLPGM("T:");
@ -1293,11 +1299,11 @@ void prepare_arc_move(char isclockwise) {
void manage_inactivity(byte debug) void manage_inactivity(byte debug)
{ {
if( (millis()-previous_millis_cmd) > max_inactive_time ) if( millis_diff(previous_millis_cmd) > max_inactive_time )
if(max_inactive_time) if(max_inactive_time)
kill(); kill();
if(stepper_inactive_time) if(stepper_inactive_time)
if( (millis()-last_stepperdisabled_time) > stepper_inactive_time ) if( millis_diff(last_stepperdisabled_time) > stepper_inactive_time )
{ {
if(previous_millis_cmd>last_stepperdisabled_time) if(previous_millis_cmd>last_stepperdisabled_time)
last_stepperdisabled_time=previous_millis_cmd; last_stepperdisabled_time=previous_millis_cmd;
@ -1309,7 +1315,7 @@ void manage_inactivity(byte debug)
} }
} }
#ifdef EXTRUDER_RUNOUT_PREVENT #ifdef EXTRUDER_RUNOUT_PREVENT
if( (millis()-previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 ) if( millis_diff(previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 )
if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP) if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP)
{ {
bool oldstatus=READ(E0_ENABLE_PIN); bool oldstatus=READ(E0_ENABLE_PIN);