Singleton for cutting tools (#14429)
This commit is contained in:
Scott Lahteine
GitHub
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2125,36 +2125,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2129,36 +2129,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2120,36 +2120,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2125,36 +2125,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2125,36 +2125,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2120,36 +2120,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2126,36 +2126,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2126,36 +2126,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2122,36 +2122,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2117,36 +2117,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2134,36 +2134,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2123,36 +2123,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2121,36 +2121,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
@ -2122,36 +2122,38 @@
|
||||
*
|
||||
* See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
|
||||
*/
|
||||
//#define SPINDLE_LASER_ENABLE
|
||||
#if ENABLED(SPINDLE_LASER_ENABLE)
|
||||
|
||||
#define SPINDLE_LASER_ENABLE_INVERT false // Set to "true" if the on/off function is reversed
|
||||
#define SPINDLE_LASER_PWM true // Set to true if your controller supports setting the speed/power
|
||||
//#define SPINDLE_FEATURE
|
||||
//#define LASER_FEATURE
|
||||
#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
|
||||
#define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH
|
||||
#define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power
|
||||
#define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower
|
||||
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
|
||||
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
|
||||
#define SPINDLE_DIR_CHANGE true // Set to true if your spindle controller supports changing spindle direction
|
||||
#define SPINDLE_INVERT_DIR false
|
||||
#define SPINDLE_STOP_ON_DIR_CHANGE true // Set to true if Marlin should stop the spindle before changing rotation direction
|
||||
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#if ENABLED(SPINDLE_FEATURE)
|
||||
//#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction
|
||||
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
|
||||
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
|
||||
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
|
||||
//#define SPEED_POWER_SLOPE 0.3922
|
||||
//#define SPEED_POWER_INTERCEPT 0
|
||||
//#define SPEED_POWER_MIN 10
|
||||
//#define SPEED_POWER_MAX 100 // 0-100%
|
||||
/**
|
||||
* The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
|
||||
*
|
||||
* SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
|
||||
* where PWM duty cycle varies from 0 to 255
|
||||
*
|
||||
* set the following for your controller (ALL MUST BE SET)
|
||||
*/
|
||||
#define SPEED_POWER_SLOPE 118.4
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 5000
|
||||
#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
|
||||
#else
|
||||
#define SPEED_POWER_SLOPE 0.3922
|
||||
#define SPEED_POWER_INTERCEPT 0
|
||||
#define SPEED_POWER_MIN 10
|
||||
#define SPEED_POWER_MAX 100 // 0-100%
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
Reference in New Issue
Block a user