Configurable TOUCH_BUTTONS repeat delays (#15245)

Marlin/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

Marlin/src/lcd/menu/menu.cpp

@@ -144,7 +144,7 @@ void MenuItem_gcode::action(PGM_P const pgcode) { queue.inject_P(pgcode); }
  */
 void MenuItemBase::edit(strfunc_t strfunc, loadfunc_t loadfunc) {
   #if ENABLED(TOUCH_BUTTONS)
-    ui.repeat_delay = 50;
+    ui.repeat_delay = BUTTON_DELAY_EDIT;
   #endif
   if (int16_t(ui.encoderPosition) < 0) ui.encoderPosition = 0;
   if (int16_t(ui.encoderPosition) > maxEditValue) ui.encoderPosition = maxEditValue;
@@ -216,7 +216,7 @@ void MarlinUI::goto_screen(screenFunc_t screen, const uint16_t encoder/*=0*/, co
   if (currentScreen != screen) {
 
     #if ENABLED(TOUCH_BUTTONS)
-      repeat_delay = 250;
+      repeat_delay = BUTTON_DELAY_MENU;
     #endif
 
     #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)

config/default/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -2093,6 +2093,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2232,7 +2235,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/ADIMLab/Gantry v1/Configuration.h

@@ -2063,6 +2063,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2202,7 +2205,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/ADIMLab/Gantry v2/Configuration.h

@@ -2063,6 +2063,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2202,7 +2205,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -2082,6 +2082,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2221,7 +2224,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Alfawise/U20-bltouch/Configuration.h

@@ -2145,6 +2145,9 @@
 #if ENABLED(TOUCH_BUTTONS)
   #define TOUCH_CALIBRATION // Include user calibration widget in menus (Alfawise)
 
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 100 // (ms) Button repeat delay for menus
+
   #if ENABLED(TS_V11)
     // Alfawise U20 ILI9341 2.8 TP Ver 1.1 / Green PCB on the back of touchscreen
     #define XPT2046_X_CALIBRATION   11605
@@ -2295,7 +2298,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -921,7 +921,7 @@
 
   #define MENU_ADDAUTOSTART                 // Add a menu option to run auto#.g files
 
-  #define EVENT_GCODE_SD_STOP "G28XY"       // G-code to run on Stop Print (e.g., "G28XY" or "G27")
+  #define EVENT_GCODE_SD_STOP "G28X"        // G-code to run on Stop Print (e.g., "G28XY" or "G27")
 
   /**
    * Continue after Power-Loss (Creality3D)
@@ -976,10 +976,10 @@
   #if ENABLED(SDCARD_SORT_ALPHA)
     #define SDSORT_LIMIT       40     // Maximum number of sorted items (10-256). Costs 27 bytes each.
     #define FOLDER_SORTING     -1     // -1=above  0=none  1=below
-    #define SDSORT_GCODE       false  // Allow turning sorting on/off with LCD and M34 g-code.
+    #define SDSORT_GCODE       true   // Allow turning sorting on/off with LCD and M34 g-code.
-    #define SDSORT_USES_RAM    false  // Pre-allocate a static array for faster pre-sorting.
+    #define SDSORT_USES_RAM    true   // Pre-allocate a static array for faster pre-sorting.
     #define SDSORT_USES_STACK  false  // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
-    #define SDSORT_CACHE_NAMES false  // Keep sorted items in RAM longer for speedy performance. Most expensive option.
+    #define SDSORT_CACHE_NAMES true   // Keep sorted items in RAM longer for speedy performance. Most expensive option.
     #define SDSORT_DYNAMIC_RAM false  // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
     #define SDSORT_CACHE_VFATS 2      // Maximum number of 13-byte VFAT entries to use for sorting.
                                       // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.

config/examples/Alfawise/U20/Configuration.h

@@ -1403,7 +1403,7 @@
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2)    // X point for Z homing when homing all axes (G28).
-  #define Z_SAFE_HOMING_Y_POINT MIN_PROBE_Y           // Y point for Z homing when homing all axes (G28).
+  #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2)    // Y point for Z homing when homing all axes (G28).
 #endif
 
 // Homing speeds (mm/m)
@@ -2144,6 +2144,9 @@
 #if ENABLED(TOUCH_BUTTONS)
   #define TOUCH_CALIBRATION // Include user calibration widget in menus (Alfawise)
 
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 100 // (ms) Button repeat delay for menus
+
   #if ENABLED(TS_V11)
     // Alfawise U20 ILI9341 2.8 TP Ver 1.1 / Green PCB on the back of touchscreen
     #define XPT2046_X_CALIBRATION   11605
@@ -2294,7 +2297,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Alfawise/U20/Configuration_adv.h

@@ -920,7 +920,7 @@
 
   #define MENU_ADDAUTOSTART                 // Add a menu option to run auto#.g files
 
-  #define EVENT_GCODE_SD_STOP "G28XY"       // G-code to run on Stop Print (e.g., "G28XY" or "G27")
+  #define EVENT_GCODE_SD_STOP "G28X"        // G-code to run on Stop Print (e.g., "G28XY" or "G27")
 
   /**
    * Continue after Power-Loss (Creality3D)
@@ -975,10 +975,10 @@
   #if ENABLED(SDCARD_SORT_ALPHA)
     #define SDSORT_LIMIT       40     // Maximum number of sorted items (10-256). Costs 27 bytes each.
     #define FOLDER_SORTING     -1     // -1=above  0=none  1=below
-    #define SDSORT_GCODE       false  // Allow turning sorting on/off with LCD and M34 g-code.
+    #define SDSORT_GCODE       true   // Allow turning sorting on/off with LCD and M34 g-code.
-    #define SDSORT_USES_RAM    false  // Pre-allocate a static array for faster pre-sorting.
+    #define SDSORT_USES_RAM    true   // Pre-allocate a static array for faster pre-sorting.
     #define SDSORT_USES_STACK  false  // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
-    #define SDSORT_CACHE_NAMES false  // Keep sorted items in RAM longer for speedy performance. Most expensive option.
+    #define SDSORT_CACHE_NAMES true   // Keep sorted items in RAM longer for speedy performance. Most expensive option.
     #define SDSORT_DYNAMIC_RAM false  // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
     #define SDSORT_CACHE_VFATS 2      // Maximum number of 13-byte VFAT entries to use for sorting.
                                       // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM.

config/examples/AliExpress/CL-260/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -2073,6 +2073,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2212,7 +2215,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Anet/A2/Configuration.h

@@ -2064,6 +2064,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2203,7 +2206,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Anet/A2plus/Configuration.h

@@ -2064,6 +2064,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2203,7 +2206,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Anet/A6/Configuration.h

@@ -2215,6 +2215,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2354,7 +2357,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Anet/A8/Configuration.h

@@ -2077,6 +2077,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2216,7 +2219,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Anet/A8plus/Configuration.h

@@ -2073,6 +2073,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2212,7 +2215,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Anet/E16/Configuration.h

@@ -2074,6 +2074,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2213,7 +2216,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/AnyCubic/i3/Configuration.h

@@ -2072,6 +2072,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2211,7 +2214,7 @@
  */
 #define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/ArmEd/Configuration.h

@@ -2063,6 +2063,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2202,7 +2205,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Azteeg/X5GT/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/BIBO/TouchX/default/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/BQ/Hephestos/Configuration.h

@@ -2050,6 +2050,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2189,7 +2192,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/BQ/Hephestos_2/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/BQ/WITBOX/Configuration.h

@@ -2050,6 +2050,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2189,7 +2192,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Cartesio/Configuration.h

@@ -2061,6 +2061,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2200,7 +2203,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/CR-10/Configuration.h

@@ -2072,6 +2072,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2211,7 +2214,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/CR-10S/Configuration.h

@@ -2063,6 +2063,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2202,7 +2205,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/CR-10_5S/Configuration.h

@@ -2065,6 +2065,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2204,7 +2207,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/CR-10mini/Configuration.h

@@ -2081,6 +2081,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2220,7 +2223,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/CR-20 Pro/Configuration.h

@@ -2065,6 +2065,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2204,7 +2207,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/CR-20/Configuration.h

@@ -2065,6 +2065,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2204,7 +2207,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/CR-8/Configuration.h

@@ -2072,6 +2072,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2211,7 +2214,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/Ender-2/Configuration.h

@@ -2066,6 +2066,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2205,7 +2208,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/Ender-3/Configuration.h

@@ -2066,6 +2066,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2205,7 +2208,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/Ender-4/Configuration.h

@@ -2072,6 +2072,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2211,7 +2214,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Creality/Ender-5/Configuration.h

@@ -2065,6 +2065,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2204,7 +2207,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Dagoma/Disco Ultimate/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Einstart-S/Configuration.h

@@ -2072,6 +2072,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2211,7 +2214,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/FYSETC/AIO_II/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/FYSETC/Cheetah 1.2/base/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/FYSETC/Cheetah/BLTouch/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/FYSETC/Cheetah/base/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/FYSETC/F6_13/Configuration.h

@@ -2064,6 +2064,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2207,7 +2210,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Felix/Configuration.h

@@ -2044,6 +2044,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2183,7 +2186,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Felix/DUAL/Configuration.h

@@ -2044,6 +2044,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2183,7 +2186,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/FlashForge/CreatorPro/Configuration.h

@@ -2053,6 +2053,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2192,7 +2195,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/FolgerTech/i3-2020/Configuration.h

@@ -2068,6 +2068,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2207,7 +2210,7 @@
  */
 #define NUM_SERVOS 2 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 500, 500 }

config/examples/Formbot/Raptor/Configuration.h

@@ -2167,6 +2167,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2306,7 +2309,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Formbot/T_Rex_2+/Configuration.h

@@ -2096,6 +2096,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2235,7 +2238,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Formbot/T_Rex_3/Configuration.h

@@ -2090,6 +2090,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2229,7 +2232,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/A10/Configuration.h

@@ -2047,6 +2047,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2186,7 +2189,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/A10M/Configuration.h

@@ -2047,6 +2047,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2186,7 +2189,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/A20M/Configuration.h

@@ -2049,6 +2049,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2188,7 +2191,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/GT2560/Configuration.h

@@ -2077,6 +2077,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2216,7 +2219,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 #define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/MeCreator2/Configuration.h

@@ -2069,6 +2069,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2208,7 +2211,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -2083,6 +2083,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2222,7 +2225,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -2082,6 +2082,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2221,7 +2224,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/HMS434/Configuration.h

@@ -2043,6 +2043,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2182,7 +2185,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Infitary/i3-M508/Configuration.h

@@ -2066,6 +2066,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2205,7 +2208,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/JGAurora/A1/Configuration.h

@@ -2071,6 +2071,9 @@
 //
 #define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2211,7 +2214,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/JGAurora/A5/Configuration.h

@@ -2074,6 +2074,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2213,7 +2216,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/JGAurora/A5S/Configuration.h

@@ -2071,6 +2071,9 @@
 //
 #define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2211,7 +2214,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/MakerParts/Configuration.h

@@ -2082,6 +2082,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2221,7 +2224,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Malyan/M150/Configuration.h

@@ -2090,6 +2090,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2229,7 +2232,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Malyan/M200/Configuration.h

@@ -2061,6 +2061,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2200,7 +2203,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Micromake/C1/basic/Configuration.h

@@ -2066,6 +2066,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2205,7 +2208,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Micromake/C1/enhanced/Configuration.h

@@ -2066,6 +2066,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2205,7 +2208,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Mks/Robin/Configuration.h

@@ -2062,12 +2062,22 @@
 //
 // ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
 //
-//#define TOUCH_BUTTONS
+#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
-  #define XPT2046_X_CALIBRATION   12316
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
-  #define XPT2046_Y_CALIBRATION  -8981
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
-  #define XPT2046_X_OFFSET       -43
+
-  #define XPT2046_Y_OFFSET        257
+  /* MKS Robin TFT v2.0 */
+  #define XPT2046_X_CALIBRATION    12013
+  #define XPT2046_Y_CALIBRATION    -8711
+  #define XPT2046_X_OFFSET           -32
+  #define XPT2046_Y_OFFSET           256
+
+  /* MKS Robin TFT v1.1 */
+  //#define XPT2046_X_CALIBRATION -11792
+  //#define XPT2046_Y_CALIBRATION   8947
+  //#define XPT2046_X_OFFSET         342
+  //#define XPT2046_Y_OFFSET         -19
 #endif
 
 //
@@ -2203,7 +2213,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Mks/Sbase/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Printrbot/PrintrboardG2/Configuration.h

@@ -2070,6 +2070,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2209,7 +2212,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/RapideLite/RL200/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/RepRapPro/Huxley/Configuration.h

@@ -2111,6 +2111,9 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2250,7 +2253,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/RigidBot/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/SCARA/Configuration.h

@@ -2071,6 +2071,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2210,7 +2213,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/STM32/Black_STM32F407VET6/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 #define NUM_SERVOS 2 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300, 300 }

config/examples/STM32/STM32F103R/Configuration.h

@@ -2064,6 +2064,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2203,7 +2206,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/STM32/STM32F4/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/STM32/stm32f103ret6/Configuration.h

@@ -2064,6 +2064,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2203,7 +2206,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Sanguinololu/Configuration.h

@@ -2093,6 +2093,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2232,7 +2235,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Tevo/Michelangelo/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Tevo/Tarantula Pro/Configuration.h

@@ -2060,6 +2060,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2199,7 +2202,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h

@@ -2067,6 +2067,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2206,7 +2209,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/TheBorg/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/TinyBoy2/Configuration.h

@@ -2118,6 +2118,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2257,7 +2260,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Tronxy/X1/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Tronxy/X3A/Configuration.h

@@ -2066,6 +2066,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2205,7 +2208,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Tronxy/X5S-2E/Configuration.h

@@ -2083,6 +2083,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2222,7 +2225,7 @@
  */
 #define NUM_SERVOS 2 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300, 300 }

config/examples/Tronxy/X5S/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/Tronxy/XY100/Configuration.h

@@ -2073,6 +2073,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2212,7 +2215,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }

config/examples/UltiMachine/Archim1/Configuration.h

@@ -2062,6 +2062,9 @@
 //
 //#define TOUCH_BUTTONS
 #if ENABLED(TOUCH_BUTTONS)
+  #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
+  #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
+
   #define XPT2046_X_CALIBRATION   12316
   #define XPT2046_Y_CALIBRATION  -8981
   #define XPT2046_X_OFFSET       -43
@@ -2201,7 +2204,7 @@
  */
 //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
 
-// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.
+// (ms) Delay  before the next move will start, to give the servo time to reach its target angle.
 // 300ms is a good value but you can try less delay.
 // If the servo can't reach the requested position, increase it.
 #define SERVO_DELAY { 300 }