Allow increasing the software PWM frequency.

This commit is contained in:
Erik van der Zalm 2013-06-09 12:52:49 +02:00
parent 8b0d82e9db
commit c8dcc7c208
4 changed files with 46 additions and 22 deletions

View File

@ -457,6 +457,17 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
//#define FAST_PWM_FAN
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
// is too low, you should also increment SOFT_PWM_SCALE.
//#define FAN_SOFT_PWM
// Incrementing this by 1 will double the software PWM frequency,
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
// However, control resolution will be halved for each increment;
// at zero value, there are 128 effective control positions.
#define SOFT_PWM_SCALE 0
// M240 Triggers a camera by emulating a Canon RC-1 Remote
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
// #define PHOTOGRAPH_PIN 23

View File

@ -191,6 +191,10 @@ extern int ValvePressure;
extern int EtoPPressure;
#endif
#ifdef FAN_SOFT_PWM
extern unsigned char fanSpeedSoftPwm;
#endif
#ifdef FWRETRACT
extern bool autoretract_enabled;
extern bool retracted;

View File

@ -473,7 +473,6 @@ void check_axes_activity()
disable_e2();
}
#if defined(FAN_PIN) && FAN_PIN > -1
#ifndef FAN_SOFT_PWM
#ifdef FAN_KICKSTART_TIME
static unsigned long fan_kick_end;
if (tail_fan_speed) {
@ -488,6 +487,9 @@ void check_axes_activity()
fan_kick_end = 0;
}
#endif//FAN_KICKSTART_TIME
#ifdef FAN_SOFT_PWM
fanSpeedSoftPwm = tail_fan_speed;
#else
analogWrite(FAN_PIN,tail_fan_speed);
#endif//!FAN_SOFT_PWM
#endif//FAN_PIN > -1
@ -757,7 +759,7 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
block->acceleration_st = axis_steps_per_sqr_second[Z_AXIS];
}
block->acceleration = block->acceleration_st / steps_per_mm;
block->acceleration_rate = (long)((float)block->acceleration_st * 8.388608);
block->acceleration_rate = (long)((float)block->acceleration_st * (16777216.0 / (F_CPU / 8.0)));
#if 0 // Use old jerk for now
// Compute path unit vector

View File

@ -62,6 +62,9 @@ float current_temperature_bed = 0.0;
float bedKd=(DEFAULT_bedKd/PID_dT);
#endif //PIDTEMPBED
#ifdef FAN_SOFT_PWM
unsigned char fanSpeedSoftPwm;
#endif
//===========================================================================
//=============================private variables============================
@ -145,6 +148,10 @@ int watch_start_temp[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0);
unsigned long watchmillis[EXTRUDERS] = ARRAY_BY_EXTRUDERS(0,0,0);
#endif //WATCH_TEMP_PERIOD
#ifndef SOFT_PWM_SCALE
#define SOFT_PWM_SCALE 0
#endif
//===========================================================================
//============================= functions ============================
//===========================================================================
@ -720,7 +727,7 @@ void tp_init()
setPwmFrequency(FAN_PIN, 1); // No prescaling. Pwm frequency = F_CPU/256/8
#endif
#ifdef FAN_SOFT_PWM
soft_pwm_fan=(unsigned char)fanSpeed;
soft_pwm_fan = fanSpeedSoftPwm / 2;
#endif
#endif
@ -1028,7 +1035,7 @@ ISR(TIMER0_COMPB_vect)
static unsigned long raw_temp_2_value = 0;
static unsigned long raw_temp_bed_value = 0;
static unsigned char temp_state = 0;
static unsigned char pwm_count = 1;
static unsigned char pwm_count = (1 << SOFT_PWM_SCALE);
static unsigned char soft_pwm_0;
#if EXTRUDERS > 1
static unsigned char soft_pwm_1;
@ -1056,7 +1063,7 @@ ISR(TIMER0_COMPB_vect)
if(soft_pwm_b > 0) WRITE(HEATER_BED_PIN,1);
#endif
#ifdef FAN_SOFT_PWM
soft_pwm_fan =(unsigned char) fanSpeed;
soft_pwm_fan = fanSpeedSoftPwm / 2;
if(soft_pwm_fan > 0) WRITE(FAN_PIN,1);
#endif
}
@ -1074,7 +1081,7 @@ ISR(TIMER0_COMPB_vect)
if(soft_pwm_fan <= pwm_count) WRITE(FAN_PIN,0);
#endif
pwm_count++;
pwm_count += (1 << SOFT_PWM_SCALE);
pwm_count &= 0x7f;
switch(temp_state) {