Fix Rumba32 variant for Marlin (#21497)
This commit is contained in:
Victor Oliveira
Scott Lahteine
parent
c2c73215b2
commit
c197ecc99b
@ -0,0 +1,454 @@
|
||||
/*
|
||||
*******************************************************************************
|
||||
* Copyright (c) 2020, STMicroelectronics
|
||||
* All rights reserved.
|
||||
*
|
||||
* This software component is licensed by ST under BSD 3-Clause license,
|
||||
* the "License"; You may not use this file except in compliance with the
|
||||
* License. You may obtain a copy of the License at:
|
||||
* opensource.org/licenses/BSD-3-Clause
|
||||
*
|
||||
*******************************************************************************
|
||||
* Automatically generated from STM32F446V(C-E)Tx.xml
|
||||
*/
|
||||
#include "Arduino.h"
|
||||
#include "PeripheralPins.h"
|
||||
|
||||
/* =====
|
||||
* Note: Commented lines are alternative possibilities which are not used per default.
|
||||
* If you change them, you will have to know what you do
|
||||
* =====
|
||||
*/
|
||||
|
||||
//*** ADC ***
|
||||
|
||||
#ifdef HAL_ADC_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_ADC[] = {
|
||||
{PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0
|
||||
// {PA_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC2_IN0
|
||||
// {PA_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC3_IN0
|
||||
{PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1
|
||||
// {PA_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC2_IN1
|
||||
// {PA_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC3_IN1
|
||||
{PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2
|
||||
// {PA_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC2_IN2
|
||||
// {PA_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC3_IN2
|
||||
{PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3
|
||||
// {PA_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC2_IN3
|
||||
// {PA_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC3_IN3
|
||||
{PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4
|
||||
// {PA_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC2_IN4
|
||||
{PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5
|
||||
// {PA_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5
|
||||
{PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6
|
||||
// {PA_6, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6
|
||||
{PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7
|
||||
// {PA_7, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7
|
||||
{PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8
|
||||
// {PB_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8
|
||||
{PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9
|
||||
// {PB_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC2_IN9
|
||||
{PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10
|
||||
// {PC_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC2_IN10
|
||||
// {PC_0, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC3_IN10
|
||||
{PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11
|
||||
// {PC_1, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC2_IN11
|
||||
// {PC_1, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC3_IN11
|
||||
{PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12
|
||||
// {PC_2, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC2_IN12
|
||||
// {PC_2, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC3_IN12
|
||||
{PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13
|
||||
// {PC_3, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC2_IN13
|
||||
// {PC_3, ADC3, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC3_IN13
|
||||
{PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14
|
||||
// {PC_4, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC2_IN14
|
||||
{PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15
|
||||
// {PC_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC2_IN15
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** DAC ***
|
||||
|
||||
#ifdef HAL_DAC_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_DAC[] = {
|
||||
// {PA_4, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // DAC_OUT1
|
||||
// {PA_5, DAC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // DAC_OUT2 - LD2
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** I2C ***
|
||||
|
||||
#ifdef HAL_I2C_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_I2C_SDA[] = {
|
||||
// {PB_3, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
|
||||
// {PB_4, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
|
||||
// {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
||||
{PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
||||
// {PC_9, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
|
||||
// {PC_12, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_I2C_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_I2C_SCL[] = {
|
||||
// {PA_8, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)},
|
||||
// {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
||||
{PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)},
|
||||
// {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** PWM ***
|
||||
|
||||
#ifdef HAL_TIM_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_PWM[] = {
|
||||
// {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
||||
{PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1
|
||||
// {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
|
||||
{PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2
|
||||
// {PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
|
||||
{PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3
|
||||
// {PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1
|
||||
// {PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4
|
||||
{PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4
|
||||
// {PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2
|
||||
// {PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
||||
// {PA_5, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N
|
||||
// {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
||||
// {PA_6, TIM13, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM13, 1, 0)}, // TIM13_CH1
|
||||
// {PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
|
||||
// {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
||||
// {PA_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 1)}, // TIM8_CH1N
|
||||
// {PA_7, TIM14, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM14, 1, 0)}, // TIM14_CH1
|
||||
{PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
|
||||
{PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
|
||||
{PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
|
||||
// {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
|
||||
{PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
||||
// {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
||||
// {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
|
||||
// {PB_0, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 1)}, // TIM8_CH2N
|
||||
// {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
||||
// {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
|
||||
// {PB_1, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 1)}, // TIM8_CH3N
|
||||
{PB_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4
|
||||
{PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
|
||||
// {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
||||
// {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
||||
// {PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
|
||||
// {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
|
||||
// {PB_8, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1
|
||||
// {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
|
||||
// {PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1
|
||||
// {PB_9, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2
|
||||
// {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
|
||||
// {PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1
|
||||
{PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3
|
||||
// {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
|
||||
// {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
||||
// {PB_14, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 1)}, // TIM8_CH2N
|
||||
{PB_14, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM12, 1, 0)}, // TIM12_CH1
|
||||
// {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
||||
// {PB_15, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 1)}, // TIM8_CH3N
|
||||
{PB_15, TIM12, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_TIM12, 2, 0)}, // TIM12_CH2
|
||||
{PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1
|
||||
// {PC_6, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 1, 0)}, // TIM8_CH1
|
||||
{PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2
|
||||
// {PC_7, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 2, 0)}, // TIM8_CH2
|
||||
{PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3
|
||||
// {PC_8, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 3, 0)}, // TIM8_CH3
|
||||
{PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4
|
||||
// {PC_9, TIM8, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM8, 4, 0)}, // TIM8_CH4
|
||||
{PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1
|
||||
{PD_13, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2
|
||||
{PD_14, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3
|
||||
{PD_15, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4
|
||||
// {PE_5, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1
|
||||
// {PE_6, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2
|
||||
// {PE_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N
|
||||
// {PE_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1
|
||||
// {PE_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N
|
||||
// {PE_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2
|
||||
// {PE_12, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N
|
||||
// {PE_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3
|
||||
{PE_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** SERIAL ***
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_UART_TX[] = {
|
||||
// {PA_0, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
||||
// {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
// {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
// {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
// {PC_6, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
||||
// {PC_10, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
||||
// {PC_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
// {PC_12, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)},
|
||||
// {PD_5, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
// {PD_8, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
{PE_8, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_UART_RX[] = {
|
||||
// {PA_1, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
||||
// {PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
{PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
// {PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
// {PC_5, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
// {PC_7, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)},
|
||||
// {PC_11, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
||||
// {PC_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
// {PD_2, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)},
|
||||
// {PD_6, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
// {PD_9, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
{PE_7, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART5)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_UART_RTS[] = {
|
||||
// {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
// {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
// {PA_15, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
||||
// {PB_14, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
// {PC_8, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_UART5)},
|
||||
// {PD_4, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
// {PD_12, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_UART_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_UART_CTS[] = {
|
||||
// {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
// {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)},
|
||||
// {PB_0, UART4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_UART4)},
|
||||
// {PB_13, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
// {PC_9, UART5, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_UART5)},
|
||||
// {PD_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)},
|
||||
// {PD_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** SPI ***
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_SPI_MOSI[] = {
|
||||
{PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
// {PB_0, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI3)},
|
||||
// {PB_2, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI3)},
|
||||
// {PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
// {PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PC_1, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI2)},
|
||||
// {PC_1, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI3)},
|
||||
// {PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PD_0, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PD_6, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI3)},
|
||||
// {PE_6, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
// {PE_14, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_SPI_MISO[] = {
|
||||
{PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
// {PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
// {PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PD_0, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
// {PE_5, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
// {PE_13, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_SPI_SCLK[] = {
|
||||
{PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
// {PA_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
// {PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PC_7, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PD_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PE_2, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
// {PE_12, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_SPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_SPI_SSEL[] = {
|
||||
{PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
// {PA_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)},
|
||||
// {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)},
|
||||
// {PB_4, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI2)},
|
||||
// {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)},
|
||||
// {PD_1, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_SPI2)},
|
||||
// {PE_4, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
// {PE_11, SPI4, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI4)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** CAN ***
|
||||
|
||||
#ifdef HAL_CAN_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_CAN_RD[] = {
|
||||
// {PA_11, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
||||
// {PB_5, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
|
||||
// {PB_8, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
||||
// {PB_12, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
|
||||
// {PD_0, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_CAN_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_CAN_TD[] = {
|
||||
// {PA_12, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
||||
// {PB_6, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
|
||||
// {PB_9, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
||||
// {PB_13, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)},
|
||||
// {PD_1, CAN1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN1)},
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** No ETHERNET ***
|
||||
|
||||
//*** QUADSPI ***
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_QUADSPI_DATA0[] = {
|
||||
// {PC_9, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO0
|
||||
// {PD_11, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO0
|
||||
// {PE_7, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_QSPI)}, // QUADSPI_BK2_IO0
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_QUADSPI_DATA1[] = {
|
||||
// {PC_10, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO1
|
||||
// {PD_12, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO1
|
||||
// {PE_8, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_QSPI)}, // QUADSPI_BK2_IO1
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_QUADSPI_DATA2[] = {
|
||||
// {PE_2, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO2
|
||||
// {PE_9, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_QSPI)}, // QUADSPI_BK2_IO2
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_QUADSPI_DATA3[] = {
|
||||
{PA_1, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO3
|
||||
// {PD_13, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK1_IO3
|
||||
// {PE_10, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_QSPI)}, // QUADSPI_BK2_IO3
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_QUADSPI_SCLK[] = {
|
||||
// {PB_2, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_CLK
|
||||
// {PD_3, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_CLK
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_QSPI_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_QUADSPI_SSEL[] = {
|
||||
// {PB_6, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_QSPI)}, // QUADSPI_BK1_NCS
|
||||
// {PC_11, QUADSPI, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF9_QSPI)}, // QUADSPI_BK2_NCS
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** USB ***
|
||||
|
||||
#ifdef HAL_PCD_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_USB_OTG_FS[] = {
|
||||
// {PA_8, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF
|
||||
// {PA_9, USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_FS_VBUS
|
||||
// {PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID
|
||||
{PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM
|
||||
{PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
#ifdef HAL_PCD_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_USB_OTG_HS[] = {
|
||||
#ifdef USE_USB_HS_IN_FS
|
||||
// {PA_4, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_OTG_HS_FS)}, // USB_OTG_HS_SOF
|
||||
// {PB_12, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF12_OTG_HS_FS)}, // USB_OTG_HS_ID
|
||||
// {PB_13, USB_OTG_HS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_HS_VBUS
|
||||
// {PB_14, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_OTG_HS_FS)}, // USB_OTG_HS_DM
|
||||
// {PB_15, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_OTG_HS_FS)}, // USB_OTG_HS_DP
|
||||
#else
|
||||
// {PA_3, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D0
|
||||
// {PA_5, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_CK
|
||||
// {PB_0, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D1
|
||||
// {PB_1, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D2
|
||||
// {PB_2, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D4
|
||||
// {PB_5, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D7
|
||||
// {PB_10, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D3
|
||||
// {PB_12, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D5
|
||||
// {PB_13, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_D6
|
||||
// {PC_0, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_STP
|
||||
// {PC_2, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_DIR
|
||||
// {PC_3, USB_OTG_HS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_HS)}, // USB_OTG_HS_ULPI_NXT
|
||||
#endif /* USE_USB_HS_IN_FS */
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
|
||||
//*** SD ***
|
||||
|
||||
#ifdef HAL_SD_MODULE_ENABLED
|
||||
WEAK const PinMap PinMap_SD[] = {
|
||||
// {PB_0, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D1
|
||||
// {PB_1, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D2
|
||||
// {PB_2, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CK
|
||||
// {PB_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D4
|
||||
// {PB_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D5
|
||||
// {PC_6, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D6
|
||||
// {PC_7, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D7
|
||||
// {PC_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D0
|
||||
// {PC_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D1
|
||||
// {PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D2
|
||||
// {PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D3
|
||||
// {PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CK
|
||||
// {PD_2, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CMD
|
||||
{NC, NP, 0}
|
||||
};
|
||||
#endif
|
||||
@ -0,0 +1,30 @@
|
||||
/* SYS_WKUP */
|
||||
#ifdef PWR_WAKEUP_PIN1
|
||||
SYS_WKUP1 = PA_0, /* SYS_WKUP0 */
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN2
|
||||
SYS_WKUP2 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN3
|
||||
SYS_WKUP3 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN4
|
||||
SYS_WKUP4 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN5
|
||||
SYS_WKUP5 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN6
|
||||
SYS_WKUP6 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN7
|
||||
SYS_WKUP7 = NC,
|
||||
#endif
|
||||
#ifdef PWR_WAKEUP_PIN8
|
||||
SYS_WKUP8 = NC,
|
||||
#endif
|
||||
/* USB */
|
||||
#ifdef USBCON
|
||||
USB_OTG_FS_DM = PA_11,
|
||||
USB_OTG_FS_DP = PA_12,
|
||||
#endif
|
||||
184
buildroot/share/PlatformIO/variants/MARLIN_F446VE/ldscript.ld
Normal file
184
buildroot/share/PlatformIO/variants/MARLIN_F446VE/ldscript.ld
Normal file
@ -0,0 +1,184 @@
|
||||
/*
|
||||
*****************************************************************************
|
||||
**
|
||||
** File : lscript.ld
|
||||
**
|
||||
** Abstract : Linker script for STM32F446VE Device with
|
||||
** 512KByte FLASH, 128KByte RAM
|
||||
**
|
||||
** Set heap size, stack size and stack location according
|
||||
** to application requirements.
|
||||
**
|
||||
** Set memory bank area and size if external memory is used.
|
||||
**
|
||||
** Target : STMicroelectronics STM32
|
||||
**
|
||||
**
|
||||
** Distribution: The file is distributed as is, without any warranty
|
||||
** of any kind.
|
||||
**
|
||||
*****************************************************************************
|
||||
** @attention
|
||||
**
|
||||
** <h2><center>© COPYRIGHT(c) 2014 Ac6</center></h2>
|
||||
**
|
||||
** Redistribution and use in source and binary forms, with or without modification,
|
||||
** are permitted provided that the following conditions are met:
|
||||
** 1. Redistributions of source code must retain the above copyright notice,
|
||||
** this list of conditions and the following disclaimer.
|
||||
** 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||
** this list of conditions and the following disclaimer in the documentation
|
||||
** and/or other materials provided with the distribution.
|
||||
** 3. Neither the name of Ac6 nor the names of its contributors
|
||||
** may be used to endorse or promote products derived from this software
|
||||
** without specific prior written permission.
|
||||
**
|
||||
** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
||||
** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||||
** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
||||
** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
||||
** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||
** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
||||
** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
||||
** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
||||
** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
||||
** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
||||
**
|
||||
*****************************************************************************
|
||||
*/
|
||||
|
||||
/* Entry Point */
|
||||
ENTRY(Reset_Handler)
|
||||
|
||||
/* Highest address of the user mode stack */
|
||||
_estack = 0x20000000 + LD_MAX_DATA_SIZE; /* end of RAM */
|
||||
/* Generate a link error if heap and stack don't fit into RAM */
|
||||
_Min_Heap_Size = 0x200; /* required amount of heap */
|
||||
_Min_Stack_Size = 0x400; /* required amount of stack */
|
||||
|
||||
/* Specify the memory areas */
|
||||
MEMORY
|
||||
{
|
||||
RAM (xrw) : ORIGIN = 0x20000000, LENGTH = LD_MAX_DATA_SIZE
|
||||
FLASH (rx) : ORIGIN = 0x08000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET
|
||||
}
|
||||
|
||||
/* Define output sections */
|
||||
SECTIONS
|
||||
{
|
||||
/* The startup code goes first into FLASH */
|
||||
.isr_vector :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
KEEP(*(.isr_vector)) /* Startup code */
|
||||
. = ALIGN(4);
|
||||
} >FLASH
|
||||
|
||||
/* The program code and other data goes into FLASH */
|
||||
.text ALIGN(4):
|
||||
{
|
||||
. = ALIGN(4);
|
||||
*(.text) /* .text sections (code) */
|
||||
*(.text*) /* .text* sections (code) */
|
||||
*(.glue_7) /* glue arm to thumb code */
|
||||
*(.glue_7t) /* glue thumb to arm code */
|
||||
*(.eh_frame)
|
||||
|
||||
KEEP (*(.init))
|
||||
KEEP (*(.fini))
|
||||
|
||||
. = ALIGN(4);
|
||||
_etext = .; /* define a global symbols at end of code */
|
||||
} >FLASH
|
||||
|
||||
/* Constant data goes into FLASH */
|
||||
.rodata ALIGN(4):
|
||||
{
|
||||
. = ALIGN(4);
|
||||
*(.rodata) /* .rodata sections (constants, strings, etc.) */
|
||||
*(.rodata*) /* .rodata* sections (constants, strings, etc.) */
|
||||
. = ALIGN(4);
|
||||
} >FLASH
|
||||
|
||||
.ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
|
||||
.ARM : {
|
||||
__exidx_start = .;
|
||||
*(.ARM.exidx*)
|
||||
__exidx_end = .;
|
||||
} >FLASH
|
||||
|
||||
.preinit_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__preinit_array_start = .);
|
||||
KEEP (*(.preinit_array*))
|
||||
PROVIDE_HIDDEN (__preinit_array_end = .);
|
||||
} >FLASH
|
||||
.init_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__init_array_start = .);
|
||||
KEEP (*(SORT(.init_array.*)))
|
||||
KEEP (*(.init_array*))
|
||||
PROVIDE_HIDDEN (__init_array_end = .);
|
||||
} >FLASH
|
||||
.fini_array :
|
||||
{
|
||||
PROVIDE_HIDDEN (__fini_array_start = .);
|
||||
KEEP (*(SORT(.fini_array.*)))
|
||||
KEEP (*(.fini_array*))
|
||||
PROVIDE_HIDDEN (__fini_array_end = .);
|
||||
} >FLASH
|
||||
|
||||
/* used by the startup to initialize data */
|
||||
_sidata = LOADADDR(.data);
|
||||
|
||||
/* Initialized data sections goes into RAM, load LMA copy after code */
|
||||
.data :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
_sdata = .; /* create a global symbol at data start */
|
||||
*(.data) /* .data sections */
|
||||
*(.data*) /* .data* sections */
|
||||
|
||||
. = ALIGN(4);
|
||||
_edata = .; /* define a global symbol at data end */
|
||||
} >RAM AT> FLASH
|
||||
|
||||
/*_siccmram = LOADADDR(.ccmram);*/
|
||||
|
||||
/* Uninitialized data section */
|
||||
. = ALIGN(4);
|
||||
.bss :
|
||||
{
|
||||
/* This is used by the startup in order to initialize the .bss secion */
|
||||
_sbss = .; /* define a global symbol at bss start */
|
||||
__bss_start__ = _sbss;
|
||||
*(.bss)
|
||||
*(.bss*)
|
||||
*(COMMON)
|
||||
|
||||
. = ALIGN(4);
|
||||
_ebss = .; /* define a global symbol at bss end */
|
||||
__bss_end__ = _ebss;
|
||||
} >RAM
|
||||
|
||||
/* User_heap_stack section, used to check that there is enough RAM left */
|
||||
._user_heap_stack :
|
||||
{
|
||||
. = ALIGN(4);
|
||||
PROVIDE ( end = . );
|
||||
PROVIDE ( _end = . );
|
||||
. = . + _Min_Heap_Size;
|
||||
. = . + _Min_Stack_Size;
|
||||
. = ALIGN(4);
|
||||
} >RAM
|
||||
|
||||
/* Remove information from the standard libraries */
|
||||
/DISCARD/ :
|
||||
{
|
||||
libc.a ( * )
|
||||
libm.a ( * )
|
||||
libgcc.a ( * )
|
||||
}
|
||||
|
||||
.ARM.attributes 0 : { *(.ARM.attributes) }
|
||||
}
|
||||
212
buildroot/share/PlatformIO/variants/MARLIN_F446VE/variant.cpp
Normal file
212
buildroot/share/PlatformIO/variants/MARLIN_F446VE/variant.cpp
Normal file
@ -0,0 +1,212 @@
|
||||
/*
|
||||
Copyright (c) 2011 Arduino. All right reserved.
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#include "pins_arduino.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
// Pin number
|
||||
const PinName digitalPin[] = {
|
||||
PA_0, //D0 //A7
|
||||
PA_1, //D1 //A8
|
||||
PA_2, //D2 //A9
|
||||
PA_3, //D3 //A0
|
||||
PA_4, //D4 //A1
|
||||
PA_5, //D5 //A10
|
||||
PA_6, //D6 //A11
|
||||
PA_7, //D7 //A12
|
||||
PA_8, //D8
|
||||
PA_9, //D9
|
||||
PA_10, //D10
|
||||
PA_11, //D11
|
||||
PA_12, //D12
|
||||
PA_13, //D13
|
||||
PA_14, //D14
|
||||
PA_15, //D15
|
||||
PB_0, //D16 //A13
|
||||
PB_1, //D17 //A14
|
||||
PB_2, //D18
|
||||
PB_3, //D19
|
||||
PB_4, //D20
|
||||
PB_5, //D21
|
||||
PB_6, //D22
|
||||
PB_7, //D23
|
||||
PB_8, //D24
|
||||
PB_9, //D25
|
||||
PB_10, //D26
|
||||
PB_11, //D27
|
||||
PB_12, //D28
|
||||
PB_13, //D29
|
||||
PB_14, //D30
|
||||
PB_15, //D31
|
||||
PC_0, //D32 //A2
|
||||
PC_1, //D33 //A3
|
||||
PC_2, //D34 //A4
|
||||
PC_3, //D35 //A5
|
||||
PC_4, //D36 //A6
|
||||
PC_5, //D37 //A15
|
||||
PC_6, //D38
|
||||
PC_7, //D39
|
||||
PC_8, //D40
|
||||
PC_9, //D41
|
||||
PC_10, //D42
|
||||
PC_11, //D43
|
||||
PC_12, //D44
|
||||
PC_13, //D45
|
||||
PC_14, //D46
|
||||
PC_15, //D47
|
||||
PD_0, //D48
|
||||
PD_1, //D49
|
||||
PD_2, //D50
|
||||
PD_3, //D51
|
||||
PD_4, //D52
|
||||
PD_5, //D53
|
||||
PD_6, //D54
|
||||
PD_7, //D55
|
||||
PD_8, //D56
|
||||
PD_9, //D57
|
||||
PD_10, //D58
|
||||
PD_11, //D59
|
||||
PD_12, //D60
|
||||
PD_13, //D61
|
||||
PD_14, //D62
|
||||
PD_15, //D63
|
||||
PE_0, //D64
|
||||
PE_1, //D65
|
||||
PE_2, //D66
|
||||
PE_3, //D67
|
||||
PE_4, //D68
|
||||
PE_5, //D69
|
||||
PE_6, //D70
|
||||
PE_7, //D71
|
||||
PE_8, //D72
|
||||
PE_9, //D73
|
||||
PE_10, //D74
|
||||
PE_11, //D75
|
||||
PE_12, //D76
|
||||
PE_13, //D77
|
||||
PE_14, //D78
|
||||
PE_15 //D79
|
||||
};
|
||||
|
||||
// Analog (Ax) pin number array
|
||||
const uint32_t analogInputPin[] = {
|
||||
3, //D3 //A0
|
||||
4, //D4 //A1
|
||||
32, //D32 //A2
|
||||
33, //D33 //A3
|
||||
34, //D34 //A4
|
||||
35, //D35 //A5
|
||||
36, //D36 //A6
|
||||
0, //D0 //A7
|
||||
1, //D1 //A8
|
||||
2, //D2 //A9
|
||||
5, //D5 //A10
|
||||
6, //D6 //A11
|
||||
7, //D7 //A12
|
||||
16, //D16 //A13
|
||||
17, //D17 //A14
|
||||
37 //D37 //A15
|
||||
};
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
// ----------------------------------------------------------------------------
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif
|
||||
|
||||
/**
|
||||
* @brief System Clock Configuration
|
||||
* The system Clock is configured as follow :
|
||||
* System Clock source = PLL (HSE)
|
||||
* SYSCLK(Hz) = 168000000
|
||||
* HCLK(Hz) = 168000000
|
||||
* AHB Prescaler = 1
|
||||
* APB1 Prescaler = 4
|
||||
* APB2 Prescaler = 2
|
||||
* HSE Frequency(Hz) = 8000000
|
||||
* PLL_M = 8
|
||||
* PLL_N = 336
|
||||
* PLL_P = 2
|
||||
* PLL_Q = 7
|
||||
* VDD(V) = 3.3
|
||||
* Main regulator output voltage = Scale1 mode
|
||||
* Flash Latency(WS) = 5
|
||||
* @param None
|
||||
* @retval None
|
||||
*/
|
||||
WEAK void SystemClock_Config(void)
|
||||
{
|
||||
RCC_ClkInitTypeDef RCC_ClkInitStruct;
|
||||
RCC_OscInitTypeDef RCC_OscInitStruct;
|
||||
RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
|
||||
|
||||
|
||||
/* Enable Power Control clock */
|
||||
__HAL_RCC_PWR_CLK_ENABLE();
|
||||
|
||||
#ifdef HAL_PWR_MODULE_ENABLED
|
||||
/* The voltage scaling allows optimizing the power consumption when the device is
|
||||
clocked below the maximum system frequency, to update the voltage scaling value
|
||||
regarding system frequency refer to product datasheet. */
|
||||
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
|
||||
#endif
|
||||
|
||||
/* Enable HSE Oscillator and activate PLL with HSE as source */
|
||||
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
|
||||
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
|
||||
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
|
||||
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
|
||||
RCC_OscInitStruct.PLL.PLLM = 6;
|
||||
RCC_OscInitStruct.PLL.PLLN = 180;
|
||||
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
|
||||
RCC_OscInitStruct.PLL.PLLQ = 7;
|
||||
RCC_OscInitStruct.PLL.PLLR = 2;
|
||||
HAL_RCC_OscConfig(&RCC_OscInitStruct);
|
||||
|
||||
HAL_PWREx_EnableOverDrive();
|
||||
|
||||
/* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
|
||||
clocks dividers */
|
||||
RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK |
|
||||
RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
|
||||
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLRCLK;
|
||||
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
|
||||
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
|
||||
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
|
||||
HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
|
||||
|
||||
PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_CLK48;
|
||||
PeriphClkInitStruct.PLLSAI.PLLSAIM = 6;
|
||||
PeriphClkInitStruct.PLLSAI.PLLSAIN = 96;
|
||||
PeriphClkInitStruct.PLLSAI.PLLSAIQ = 2;
|
||||
PeriphClkInitStruct.PLLSAI.PLLSAIP = RCC_PLLSAIP_DIV4;
|
||||
PeriphClkInitStruct.PLLSAIDivQ = 1;
|
||||
PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48CLKSOURCE_PLLSAIP;
|
||||
HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
|
||||
}
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
186
buildroot/share/PlatformIO/variants/MARLIN_F446VE/variant.h
Normal file
186
buildroot/share/PlatformIO/variants/MARLIN_F446VE/variant.h
Normal file
@ -0,0 +1,186 @@
|
||||
/*
|
||||
Copyright (c) 2011 Arduino. All right reserved.
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#ifndef _VARIANT_ARDUINO_STM32_
|
||||
#define _VARIANT_ARDUINO_STM32_
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif // __cplusplus
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Pins
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#define PA0 PIN_A7 //D0
|
||||
#define PA1 PIN_A8 //D1
|
||||
#define PA2 PIN_A9 //D2
|
||||
#define PA3 PIN_A0 //D3
|
||||
#define PA4 PIN_A1 //D4
|
||||
#define PA5 PIN_A10 //D5
|
||||
#define PA6 PIN_A11 //D6
|
||||
#define PA7 PIN_A12 //D7
|
||||
#define PA8 8 //D8
|
||||
#define PA9 9 //D9
|
||||
#define PA10 10 //D10
|
||||
#define PA11 11 //D11
|
||||
#define PA12 12 //D12
|
||||
#define PA13 13 //D13
|
||||
#define PA14 14 //D14
|
||||
#define PA15 15 //D15
|
||||
#define PB0 PIN_A13 //D16
|
||||
#define PB1 PIN_A14 //D17
|
||||
#define PB2 18 //D18
|
||||
#define PB3 19 //D19
|
||||
#define PB4 20 //D20
|
||||
#define PB5 21 //D21
|
||||
#define PB6 22 //D22
|
||||
#define PB7 23 //D23
|
||||
#define PB8 24 //D24
|
||||
#define PB9 25 //D25
|
||||
#define PB10 26 //D26
|
||||
#define PB11 27 //D27
|
||||
#define PB12 28 //D28
|
||||
#define PB13 29 //D29
|
||||
#define PB14 30 //D30
|
||||
#define PB15 31 //D31
|
||||
#define PC0 PIN_A2 //D32
|
||||
#define PC1 PIN_A3 //D33
|
||||
#define PC2 PIN_A4 //D34
|
||||
#define PC3 PIN_A5 //D35
|
||||
#define PC4 PIN_A6 //D36
|
||||
#define PC5 PIN_A15 //D37
|
||||
#define PC6 38 //D38
|
||||
#define PC7 39 //D39
|
||||
#define PC8 40 //D40
|
||||
#define PC9 41 //D41
|
||||
#define PC10 42 //D42
|
||||
#define PC11 43 //D43
|
||||
#define PC12 44 //D44
|
||||
#define PC13 45 //D45
|
||||
#define PC14 46 //D46
|
||||
#define PC15 47 //D47
|
||||
#define PD0 48 //D48
|
||||
#define PD1 49 //D49
|
||||
#define PD2 50 //D50
|
||||
#define PD3 51 //D51
|
||||
#define PD4 52 //D52
|
||||
#define PD5 53 //D53
|
||||
#define PD6 54 //D54
|
||||
#define PD7 55 //D55
|
||||
#define PD8 56 //D56
|
||||
#define PD9 57 //D57
|
||||
#define PD10 58 //D58
|
||||
#define PD11 59 //D59
|
||||
#define PD12 60 //D60
|
||||
#define PD13 61 //D61
|
||||
#define PD14 62 //D62
|
||||
#define PD15 63 //D63
|
||||
#define PE0 64 //D64
|
||||
#define PE1 65 //D65
|
||||
#define PE2 66 //D66
|
||||
#define PE3 67 //D67
|
||||
#define PE4 68 //D68
|
||||
#define PE5 69 //D69
|
||||
#define PE6 70 //D70
|
||||
#define PE7 71 //D71
|
||||
#define PE8 72 //D72
|
||||
#define PE9 73 //D73
|
||||
#define PE10 74 //D74
|
||||
#define PE11 75 //D75
|
||||
#define PE12 76 //D76
|
||||
#define PE13 77 //D77
|
||||
#define PE14 78 //D78
|
||||
#define PE15 79 //D79
|
||||
|
||||
// This must be a literal
|
||||
#define NUM_DIGITAL_PINS 80
|
||||
// This must be a literal with a value less than or equal to to MAX_ANALOG_INPUTS
|
||||
#define NUM_ANALOG_INPUTS 16
|
||||
|
||||
// PWM resolution
|
||||
#define PWM_FREQUENCY 20000 // >= 20 Khz => inaudible noise for fans
|
||||
#define PWM_MAX_DUTY_CYCLE 255
|
||||
|
||||
// On-board LED pin number
|
||||
#define LED_BUILTIN PB14
|
||||
#define LED_HEARTBEAT LED_BUILTIN
|
||||
|
||||
// SPI Definitions
|
||||
#define PIN_SPI_SS PA4
|
||||
#define PIN_SPI_MOSI PA7
|
||||
#define PIN_SPI_MISO PA6
|
||||
#define PIN_SPI_SCK PA5
|
||||
|
||||
// I2C Definitions
|
||||
#define PIN_WIRE_SDA PB9
|
||||
#define PIN_WIRE_SCL PB8
|
||||
|
||||
// Timer Definitions
|
||||
// Use TIM6/TIM7 when possible as servo and tone don't need GPIO output pin
|
||||
#ifndef TIMER_TONE
|
||||
#define TIMER_TONE TIM6
|
||||
#endif
|
||||
|
||||
#ifndef TIMER_SERVO
|
||||
#define TIMER_SERVO TIM7
|
||||
#endif
|
||||
|
||||
#ifndef TIMER_SERIAL
|
||||
#define TIMER_SERIAL TIM9
|
||||
#endif
|
||||
|
||||
// UART Definitions
|
||||
#define SERIAL_UART_INSTANCE 1 // Connected to EXP3 header
|
||||
|
||||
// Default pin used for 'Serial' instance (ex: ST-Link)
|
||||
// Mandatory for Firmata
|
||||
#define PIN_SERIAL_RX PA10
|
||||
#define PIN_SERIAL_TX PA9
|
||||
|
||||
/* HAL configuration */
|
||||
#define HSE_VALUE 12000000U
|
||||
|
||||
#ifdef __cplusplus
|
||||
} // extern "C"
|
||||
#endif
|
||||
/*----------------------------------------------------------------------------
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#ifdef __cplusplus
|
||||
// These serial port names are intended to allow libraries and architecture-neutral
|
||||
// sketches to automatically default to the correct port name for a particular type
|
||||
// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
|
||||
// the first hardware serial port whose RX/TX pins are not dedicated to another use.
|
||||
//
|
||||
// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
|
||||
//
|
||||
// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
|
||||
//
|
||||
// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
|
||||
//
|
||||
// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
|
||||
//
|
||||
// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
|
||||
// pins are NOT connected to anything by default.
|
||||
#define SERIAL_PORT_MONITOR Serial
|
||||
#define SERIAL_PORT_HARDWARE_OPEN Serial
|
||||
#endif
|
||||
|
||||
#endif /* _VARIANT_ARDUINO_STM32_ */
|
||||
@ -288,6 +288,15 @@ build_flags = ${common_stm32.build_flags}
|
||||
board = rumba32_f446ve
|
||||
upload_protocol = dfu
|
||||
monitor_speed = 500000
|
||||
board_build.core = stm32
|
||||
board_build.variant = MARLIN_F446VE
|
||||
board_build.ldscript = ldscript.ld
|
||||
board_build.offset = 0x0000
|
||||
board_build.encrypt = No
|
||||
board_build.firmware = firmware.bin
|
||||
extra_scripts = ${common.extra_scripts}
|
||||
pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py
|
||||
buildroot/share/PlatformIO/scripts/stm32_bootloader.py
|
||||
|
||||
#
|
||||
# MKS Robin Pro V2
|
||||
|
||||
Loading…
Reference in New Issue
Block a user