Merge pull request #3065 from thinkyhead/rc_doc_tweaks

Simplified endstop configuration

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+//#define USE_ZMIN_PLUG
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/biv2.5/Configuration_adv.h

@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS

Marlin/example_configurations/delta/generic/Configuration.h

@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG // a Z probe
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -381,8 +381,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+//#define USE_ZMIN_PLUG
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -405,8 +419,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -370,8 +370,22 @@
 // Enable this option for Toshiba steppers
 //#define CONFIG_STEPPERS_TOSHIBA
 
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
 // @section homing
 
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+//#define USE_XMIN_PLUG
+//#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG // a Z probe
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
+#define USE_ZMAX_PLUG
+
 // coarse Endstop Settings
 #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
 
@@ -394,8 +408,6 @@ const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o
 const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
-//#define DISABLE_MAX_ENDSTOPS
-//#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing.
 
 //===========================================================================
 //============================= Z Probe Options =============================

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -206,9 +206,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -201,9 +201,7 @@
   //#define Z_DUAL_ENDSTOPS
 
   #if ENABLED(Z_DUAL_ENDSTOPS)
-    #define Z2_MAX_PIN 36                     //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
-    const bool Z2_MAX_ENDSTOP_INVERTING = false;
-    #define DISABLE_XMAX_ENDSTOP              //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
+    #define Z2_USE_ENDSTOP _XMAX_
   #endif
 
 #endif // Z_DUAL_STEPPER_DRIVERS