Update configs with all the latest
This commit is contained in:
Scott Lahteine
@ -32,7 +32,7 @@
|
||||
|
||||
//automatic temperature: The hot end target temperature is calculated by all the buffered lines of gcode.
|
||||
//The maximum buffered steps/sec of the extruder motor are called "se".
|
||||
//You enter the autotemp mode by a M109 S<mintemp> T<maxtemp> F<factor>
|
||||
//You enter the autotemp mode by a M109 S<mintemp> B<maxtemp> F<factor>
|
||||
// the target temperature is set to mintemp+factor*se[steps/sec] and limited by mintemp and maxtemp
|
||||
// you exit the value by any M109 without F*
|
||||
// Also, if the temperature is set to a value <mintemp, it is not changed by autotemp.
|
||||
@ -77,10 +77,10 @@
|
||||
// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
|
||||
// Multiple extruders can be assigned to the same pin in which case
|
||||
// the fan will turn on when any selected extruder is above the threshold.
|
||||
#define EXTRUDER_0_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_1_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_2_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_3_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_0_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_1_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_2_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_3_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
|
||||
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
|
||||
|
||||
@ -100,6 +100,30 @@
|
||||
// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
|
||||
//#define Z_DUAL_STEPPER_DRIVERS
|
||||
|
||||
#ifdef Z_DUAL_STEPPER_DRIVERS
|
||||
|
||||
// Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
|
||||
// That way the machine is capable to align the bed during home, since both Z steppers are homed.
|
||||
// There is also an implementation of M666 (software endstops adjustment) to this feature.
|
||||
// After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
|
||||
// One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
|
||||
// If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
|
||||
// Play a little bit with small adjustments (0.5mm) and check the behaviour.
|
||||
// The M119 (endstops report) will start reporting the Z2 Endstop as well.
|
||||
|
||||
#define Z_DUAL_ENDSTOPS
|
||||
|
||||
#ifdef Z_DUAL_ENDSTOPS
|
||||
#define Z2_STEP_PIN E2_STEP_PIN // Stepper to be used to Z2 axis.
|
||||
#define Z2_DIR_PIN E2_DIR_PIN
|
||||
#define Z2_ENABLE_PIN E2_ENABLE_PIN
|
||||
#define Z2_MAX_PIN 36 //Endstop used for Z2 axis. In this case I'm using XMAX in a Rumba Board (pin 36)
|
||||
const bool Z2_MAX_ENDSTOP_INVERTING = false;
|
||||
#define DISABLE_XMAX_ENDSTOP //Better to disable the XMAX to avoid conflict. Just rename "XMAX_ENDSTOP" by the endstop you are using for Z2 axis.
|
||||
#endif
|
||||
|
||||
#endif // Z_DUAL_STEPPER_DRIVERS
|
||||
|
||||
// Same again but for Y Axis.
|
||||
//#define Y_DUAL_STEPPER_DRIVERS
|
||||
|
||||
@ -112,41 +136,41 @@
|
||||
// allowing faster printing speeds.
|
||||
//#define DUAL_X_CARRIAGE
|
||||
#ifdef DUAL_X_CARRIAGE
|
||||
// Configuration for second X-carriage
|
||||
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
|
||||
// the second x-carriage always homes to the maximum endstop.
|
||||
#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
|
||||
#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
|
||||
#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
|
||||
#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
|
||||
// However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software
|
||||
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
|
||||
// without modifying the firmware (through the "M218 T1 X???" command).
|
||||
// Remember: you should set the second extruder x-offset to 0 in your slicer.
|
||||
// Configuration for second X-carriage
|
||||
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
|
||||
// the second x-carriage always homes to the maximum endstop.
|
||||
#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
|
||||
#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
|
||||
#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
|
||||
#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
|
||||
// However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software
|
||||
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
|
||||
// without modifying the firmware (through the "M218 T1 X???" command).
|
||||
// Remember: you should set the second extruder x-offset to 0 in your slicer.
|
||||
|
||||
// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
|
||||
#define X2_ENABLE_PIN 29
|
||||
#define X2_STEP_PIN 25
|
||||
#define X2_DIR_PIN 23
|
||||
// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h)
|
||||
#define X2_ENABLE_PIN 29
|
||||
#define X2_STEP_PIN 25
|
||||
#define X2_DIR_PIN 23
|
||||
|
||||
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
|
||||
// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
|
||||
// as long as it supports dual x-carriages. (M605 S0)
|
||||
// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
|
||||
// that additional slicer support is not required. (M605 S1)
|
||||
// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
|
||||
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
|
||||
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
|
||||
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
|
||||
// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
|
||||
// as long as it supports dual x-carriages. (M605 S0)
|
||||
// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
|
||||
// that additional slicer support is not required. (M605 S1)
|
||||
// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
|
||||
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
|
||||
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
|
||||
|
||||
// This is the default power-up mode which can be later using M605.
|
||||
#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
|
||||
// This is the default power-up mode which can be later using M605.
|
||||
#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
|
||||
|
||||
// Default settings in "Auto-park Mode"
|
||||
#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
|
||||
#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
|
||||
// Default settings in "Auto-park Mode"
|
||||
#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
|
||||
#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
|
||||
|
||||
// Default x offset in duplication mode (typically set to half print bed width)
|
||||
#define DEFAULT_DUPLICATION_X_OFFSET 100
|
||||
// Default x offset in duplication mode (typically set to half print bed width)
|
||||
#define DEFAULT_DUPLICATION_X_OFFSET 100
|
||||
|
||||
#endif //DUAL_X_CARRIAGE
|
||||
|
||||
@ -159,8 +183,6 @@
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
|
||||
#define MAX_STEP_FREQUENCY 40000 // Max step frequency for Ultimaker (5000 pps / half step)
|
||||
|
||||
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
|
||||
#define INVERT_X_STEP_PIN false
|
||||
#define INVERT_Y_STEP_PIN false
|
||||
@ -205,7 +227,6 @@
|
||||
// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
|
||||
#define DIGIPOT_I2C_NUM_CHANNELS 4
|
||||
// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
|
||||
//#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
|
||||
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.7, 1.7, 1.7, 1.7}
|
||||
|
||||
//===========================================================================
|
||||
@ -213,34 +234,44 @@
|
||||
//===========================================================================
|
||||
|
||||
#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
|
||||
#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceed this value, multiple the steps moved by ten to quickly advance the value
|
||||
#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceed this value, multiple the steps moved by 100 to really quickly advance the value
|
||||
#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
|
||||
#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
|
||||
//#define ENCODER_RATE_MULTIPLIER_DEBUG // If defined, output the encoder steps per second value
|
||||
|
||||
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
|
||||
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#ifdef SDSUPPORT
|
||||
|
||||
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
|
||||
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
|
||||
// using:
|
||||
//#define MENU_ADDAUTOSTART
|
||||
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
|
||||
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
|
||||
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
|
||||
// be commented out otherwise
|
||||
//#define SDCARDDETECTINVERTED
|
||||
|
||||
// Show a progress bar on the LCD when printing from SD
|
||||
//#define LCD_PROGRESS_BAR
|
||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
|
||||
#ifdef LCD_PROGRESS_BAR
|
||||
// Amount of time (ms) to show the bar
|
||||
#define PROGRESS_BAR_BAR_TIME 2000
|
||||
// Amount of time (ms) to show the status message
|
||||
#define PROGRESS_BAR_MSG_TIME 2000
|
||||
// Amount of time (ms) to retain the status message (0=forever)
|
||||
#define PROGRESS_MSG_EXPIRE 0
|
||||
// Enable this to show messages for MSG_TIME then hide them
|
||||
//#define PROGRESS_MSG_ONCE
|
||||
#endif
|
||||
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
|
||||
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
|
||||
// using:
|
||||
//#define MENU_ADDAUTOSTART
|
||||
|
||||
// Show a progress bar on HD44780 LCDs for SD printing
|
||||
//#define LCD_PROGRESS_BAR
|
||||
|
||||
#ifdef LCD_PROGRESS_BAR
|
||||
// Amount of time (ms) to show the bar
|
||||
#define PROGRESS_BAR_BAR_TIME 2000
|
||||
// Amount of time (ms) to show the status message
|
||||
#define PROGRESS_BAR_MSG_TIME 3000
|
||||
// Amount of time (ms) to retain the status message (0=forever)
|
||||
#define PROGRESS_MSG_EXPIRE 0
|
||||
// Enable this to show messages for MSG_TIME then hide them
|
||||
//#define PROGRESS_MSG_ONCE
|
||||
#endif
|
||||
|
||||
#endif // SDSUPPORT
|
||||
|
||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
//#define USE_WATCHDOG
|
||||
@ -278,7 +309,7 @@
|
||||
#define EXTRUDER_ADVANCE_K .0
|
||||
#define D_FILAMENT 2.85
|
||||
#define STEPS_MM_E 836
|
||||
#endif // ADVANCE
|
||||
#endif
|
||||
|
||||
// Arc interpretation settings:
|
||||
#define MM_PER_ARC_SEGMENT 1
|
||||
@ -286,12 +317,6 @@
|
||||
|
||||
const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
||||
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
|
||||
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
|
||||
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
|
||||
// be commented out otherwise
|
||||
//#define SDCARDDETECTINVERTED
|
||||
|
||||
// Control heater 0 and heater 1 in parallel.
|
||||
//#define HEATERS_PARALLEL
|
||||
|
||||
@ -301,7 +326,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
#if defined SDSUPPORT
|
||||
#ifdef SDSUPPORT
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
@ -323,9 +348,11 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
#ifdef FWRETRACT
|
||||
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
|
||||
#define RETRACT_LENGTH 3 //default retract length (positive mm)
|
||||
#define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
|
||||
#define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
|
||||
#define RETRACT_ZLIFT 0 //default retract Z-lift
|
||||
#define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
|
||||
#define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
@ -341,6 +368,139 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
* enable this section if you have TMC26X motor drivers.
|
||||
* you need to import the TMC26XStepper library into the arduino IDE for this
|
||||
******************************************************************************/
|
||||
|
||||
//#define HAVE_TMCDRIVER
|
||||
#ifdef HAVE_TMCDRIVER
|
||||
|
||||
// #define X_IS_TMC
|
||||
#define X_MAX_CURRENT 1000 //in mA
|
||||
#define X_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define X2_IS_TMC
|
||||
#define X2_MAX_CURRENT 1000 //in mA
|
||||
#define X2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Y_IS_TMC
|
||||
#define Y_MAX_CURRENT 1000 //in mA
|
||||
#define Y_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Y2_IS_TMC
|
||||
#define Y2_MAX_CURRENT 1000 //in mA
|
||||
#define Y2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Z_IS_TMC
|
||||
#define Z_MAX_CURRENT 1000 //in mA
|
||||
#define Z_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Z2_IS_TMC
|
||||
#define Z2_MAX_CURRENT 1000 //in mA
|
||||
#define Z2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E0_IS_TMC
|
||||
#define E0_MAX_CURRENT 1000 //in mA
|
||||
#define E0_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E1_IS_TMC
|
||||
#define E1_MAX_CURRENT 1000 //in mA
|
||||
#define E1_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E2_IS_TMC
|
||||
#define E2_MAX_CURRENT 1000 //in mA
|
||||
#define E2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E3_IS_TMC
|
||||
#define E3_MAX_CURRENT 1000 //in mA
|
||||
#define E3_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
* enable this section if you have L6470 motor drivers.
|
||||
* you need to import the L6470 library into the arduino IDE for this
|
||||
******************************************************************************/
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#ifdef HAVE_L6470DRIVER
|
||||
|
||||
// #define X_IS_L6470
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
#define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define X2_IS_L6470
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
#define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Y_IS_L6470
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
#define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Y2_IS_L6470
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
#define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Z_IS_L6470
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
#define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Z2_IS_L6470
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
#define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E0_IS_L6470
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
#define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E1_IS_L6470
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
#define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E2_IS_L6470
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
#define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E3_IS_L6470
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
#define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
#endif
|
||||
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
||||
|
||||
Reference in New Issue
Block a user