Followup to #15481
This commit is contained in:
Scott Lahteine
parent
af80653f3f
commit
b4d48fdc91
@ -54,46 +54,19 @@
|
||||
* http://www.thingiverse.com/thing:298812
|
||||
*/
|
||||
|
||||
//===========================================================================
|
||||
//============================= DELTA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Delta printer start with one of the configuration files in the
|
||||
// config/examples/delta directory and customize for your machine.
|
||||
//
|
||||
|
||||
//===========================================================================
|
||||
//============================= SCARA Printer ===============================
|
||||
//===========================================================================
|
||||
|
||||
/**
|
||||
* MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
|
||||
* Implemented and slightly reworked by JCERNY in June, 2014.
|
||||
*/
|
||||
|
||||
// Specify the specific SCARA model
|
||||
#define MORGAN_SCARA
|
||||
|
||||
#if ENABLED(MORGAN_SCARA)
|
||||
|
||||
//#define DEBUG_SCARA_KINEMATICS
|
||||
#define SCARA_FEEDRATE_SCALING // Convert XY feedrate from mm/s to degrees/s on the fly
|
||||
|
||||
// If movement is choppy try lowering this value
|
||||
#define SCARA_SEGMENTS_PER_SECOND 200
|
||||
|
||||
// Length of inner and outer support arms. Measure arm lengths precisely.
|
||||
#define SCARA_LINKAGE_1 150 //mm
|
||||
#define SCARA_LINKAGE_2 150 //mm
|
||||
|
||||
// SCARA tower offset (position of Tower relative to bed zero position)
|
||||
// This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
|
||||
#define SCARA_OFFSET_X 100 //mm
|
||||
#define SCARA_OFFSET_Y -56 //mm
|
||||
|
||||
// Radius around the center where the arm cannot reach
|
||||
#define MIDDLE_DEAD_ZONE_R 0 //mm
|
||||
|
||||
#define THETA_HOMING_OFFSET 0 //calculatated from Calibration Guide and command M360 / M114 see picture in http://reprap.harleystudio.co.za/?page_id=1073
|
||||
#define PSI_HOMING_OFFSET 0 //calculatated from Calibration Guide and command M364 / M114 see picture in http://reprap.harleystudio.co.za/?page_id=1073
|
||||
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//==================== END ==== SCARA Printer ==== END ======================
|
||||
//===========================================================================
|
||||
// For a SCARA printer start with the configuration files in
|
||||
// config/examples/SCARA and customize for your machine.
|
||||
//
|
||||
|
||||
// @section info
|
||||
|
||||
@ -160,7 +133,7 @@
|
||||
#endif
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
#define CUSTOM_MACHINE_NAME "SCARA"
|
||||
//#define CUSTOM_MACHINE_NAME "3D Printer"
|
||||
|
||||
// Printer's unique ID, used by some programs to differentiate between machines.
|
||||
// Choose your own or use a service like http://www.uuidgenerator.net/version4
|
||||
@ -347,7 +320,7 @@
|
||||
* Enable and connect the power supply to the PS_ON_PIN.
|
||||
* Specify whether the power supply is active HIGH or active LOW.
|
||||
*/
|
||||
#define PSU_CONTROL
|
||||
//#define PSU_CONTROL
|
||||
//#define PSU_NAME "Power Supply"
|
||||
|
||||
#if ENABLED(PSU_CONTROL)
|
||||
@ -436,7 +409,7 @@
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_4 0
|
||||
#define TEMP_SENSOR_5 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
#define TEMP_SENSOR_BED 0
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
@ -448,11 +421,11 @@
|
||||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||||
|
||||
#define TEMP_RESIDENCY_TIME 3 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_HYSTERESIS 2 // (°C) Temperature proximity considered "close enough" to the target
|
||||
#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
#define TEMP_BED_RESIDENCY_TIME 0 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
@ -495,13 +468,25 @@
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
|
||||
// Merlin Hotend: From Autotune
|
||||
#define DEFAULT_Kp 24.5
|
||||
#define DEFAULT_Ki 1.72
|
||||
#define DEFAULT_Kd 87.73
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
|
||||
// Ultimaker
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
//#define DEFAULT_Kp 7.0
|
||||
//#define DEFAULT_Ki 0.1
|
||||
//#define DEFAULT_Kd 12
|
||||
|
||||
// Mendel Parts V9 on 12V
|
||||
//#define DEFAULT_Kp 63.0
|
||||
//#define DEFAULT_Ki 2.25
|
||||
//#define DEFAULT_Kd 440
|
||||
|
||||
#endif // PIDTEMP
|
||||
|
||||
@ -522,7 +507,7 @@
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
#define PIDTEMPBED
|
||||
//#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
@ -538,11 +523,17 @@
|
||||
//#define MIN_BED_POWER 0
|
||||
//#define PID_BED_DEBUG // Sends debug data to the serial port.
|
||||
|
||||
//12v Heatbed Mk3 12V in parallel
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
#define DEFAULT_bedKp 630.14
|
||||
#define DEFAULT_bedKi 121.71
|
||||
#define DEFAULT_bedKd 815.64
|
||||
//#define DEFAULT_bedKp 97.1
|
||||
//#define DEFAULT_bedKi 1.41
|
||||
//#define DEFAULT_bedKd 1675.16
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#endif // PIDTEMPBED
|
||||
@ -611,23 +602,23 @@
|
||||
// Specify here all the endstop connectors that are connected to any endstop or probe.
|
||||
// Almost all printers will be using one per axis. Probes will use one or more of the
|
||||
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
|
||||
//#define USE_XMIN_PLUG
|
||||
//#define USE_YMIN_PLUG
|
||||
#define USE_XMIN_PLUG
|
||||
#define USE_YMIN_PLUG
|
||||
#define USE_ZMIN_PLUG
|
||||
#define USE_XMAX_PLUG
|
||||
#define USE_YMAX_PLUG
|
||||
//#define USE_XMAX_PLUG
|
||||
//#define USE_YMAX_PLUG
|
||||
//#define USE_ZMAX_PLUG
|
||||
|
||||
// Enable pullup for all endstops to prevent a floating state
|
||||
//#define ENDSTOPPULLUPS
|
||||
#define ENDSTOPPULLUPS
|
||||
#if DISABLED(ENDSTOPPULLUPS)
|
||||
// Disable ENDSTOPPULLUPS to set pullups individually
|
||||
#define ENDSTOPPULLUP_XMAX
|
||||
#define ENDSTOPPULLUP_YMAX
|
||||
//#define ENDSTOPPULLUP_ZMAX // open pin, inverted
|
||||
//#define ENDSTOPPULLUP_XMIN // open pin, inverted
|
||||
//#define ENDSTOPPULLUP_YMIN // open pin, inverted
|
||||
#define ENDSTOPPULLUP_ZMIN
|
||||
//#define ENDSTOPPULLUP_XMAX
|
||||
//#define ENDSTOPPULLUP_YMAX
|
||||
//#define ENDSTOPPULLUP_ZMAX
|
||||
//#define ENDSTOPPULLUP_XMIN
|
||||
//#define ENDSTOPPULLUP_YMIN
|
||||
//#define ENDSTOPPULLUP_ZMIN
|
||||
//#define ENDSTOPPULLUP_ZMIN_PROBE
|
||||
#endif
|
||||
|
||||
@ -645,13 +636,13 @@
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING false
|
||||
#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
|
||||
#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Stepper Drivers
|
||||
@ -668,14 +659,14 @@
|
||||
* TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
|
||||
* :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
|
||||
*/
|
||||
#define X_DRIVER_TYPE TMC2209
|
||||
#define Y_DRIVER_TYPE TMC2130
|
||||
#define Z_DRIVER_TYPE TMC2130
|
||||
//#define X_DRIVER_TYPE A4988
|
||||
//#define Y_DRIVER_TYPE A4988
|
||||
//#define Z_DRIVER_TYPE A4988
|
||||
//#define X2_DRIVER_TYPE A4988
|
||||
//#define Y2_DRIVER_TYPE A4988
|
||||
//#define Z2_DRIVER_TYPE A4988
|
||||
//#define Z3_DRIVER_TYPE A4988
|
||||
#define E0_DRIVER_TYPE TMC2660
|
||||
//#define E0_DRIVER_TYPE A4988
|
||||
//#define E1_DRIVER_TYPE A4988
|
||||
//#define E2_DRIVER_TYPE A4988
|
||||
//#define E3_DRIVER_TYPE A4988
|
||||
@ -725,14 +716,14 @@
|
||||
* Override with M92
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 103.69, 106.65, 200/1.25, 1000 } // default steps per unit for SCARA
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
|
||||
|
||||
/**
|
||||
* Default Max Feed Rate (mm/s)
|
||||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
|
||||
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
|
||||
#if ENABLED(LIMITED_MAX_FR_EDITING)
|
||||
@ -745,7 +736,7 @@
|
||||
* Override with M201
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 300, 300, 20, 1000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
|
||||
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
|
||||
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
|
||||
@ -760,9 +751,9 @@
|
||||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 400 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration for travel (non printing) moves
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
/**
|
||||
* Default Jerk limits (mm/s)
|
||||
@ -772,10 +763,10 @@
|
||||
* When changing speed and direction, if the difference is less than the
|
||||
* value set here, it may happen instantaneously.
|
||||
*/
|
||||
#define CLASSIC_JERK
|
||||
//#define CLASSIC_JERK
|
||||
#if ENABLED(CLASSIC_JERK)
|
||||
#define DEFAULT_XJERK 5.0
|
||||
#define DEFAULT_YJERK 5.0
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_ZJERK 0.3
|
||||
|
||||
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
|
||||
@ -784,7 +775,7 @@
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#define DEFAULT_EJERK 3.0 // May be used by Linear Advance
|
||||
#define DEFAULT_EJERK 5.0 // May be used by Linear Advance
|
||||
|
||||
/**
|
||||
* Junction Deviation Factor
|
||||
@ -860,7 +851,7 @@
|
||||
* A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
|
||||
* (e.g., an inductive probe or a nozzle-based probe-switch.)
|
||||
*/
|
||||
#define FIX_MOUNTED_PROBE
|
||||
//#define FIX_MOUNTED_PROBE
|
||||
|
||||
/**
|
||||
* Z Servo Probe, such as an endstop switch on a rotating arm.
|
||||
@ -928,7 +919,7 @@
|
||||
*
|
||||
* Specify a Probe position as { X, Y, Z }
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { -25, -29, -12.35 }
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
|
||||
|
||||
// Certain types of probes need to stay away from edges
|
||||
#define MIN_PROBE_EDGE 10
|
||||
@ -968,7 +959,7 @@
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||
@ -983,7 +974,7 @@
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
// Before deploy/stow pause for user confirmation
|
||||
#define PAUSE_BEFORE_DEPLOY_STOW
|
||||
//#define PAUSE_BEFORE_DEPLOY_STOW
|
||||
#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
|
||||
//#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe
|
||||
#endif
|
||||
@ -1028,8 +1019,8 @@
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR true
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
|
||||
// @section extruder
|
||||
|
||||
@ -1052,8 +1043,8 @@
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
#define X_HOME_DIR 1
|
||||
#define Y_HOME_DIR 1
|
||||
#define X_HOME_DIR -1
|
||||
#define Y_HOME_DIR -1
|
||||
#define Z_HOME_DIR -1
|
||||
|
||||
// @section machine
|
||||
@ -1065,10 +1056,10 @@
|
||||
// Travel limits (mm) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MIN_POS MANUAL_Z_HOME_POS
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 225
|
||||
#define Z_MAX_POS 200
|
||||
|
||||
/**
|
||||
* Software Endstops
|
||||
@ -1171,7 +1162,7 @@
|
||||
*/
|
||||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
@ -1309,9 +1300,9 @@
|
||||
|
||||
// Manually set the home position. Leave these undefined for automatic settings.
|
||||
// For DELTA this is the top-center of the Cartesian print volume.
|
||||
#define MANUAL_X_HOME_POS -22
|
||||
#define MANUAL_Y_HOME_POS -52
|
||||
#define MANUAL_Z_HOME_POS 0.1
|
||||
//#define MANUAL_X_HOME_POS 0
|
||||
//#define MANUAL_Y_HOME_POS 0
|
||||
//#define MANUAL_Z_HOME_POS 0
|
||||
|
||||
// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
|
||||
//
|
||||
@ -1330,8 +1321,8 @@
|
||||
#endif
|
||||
|
||||
// Homing speeds (mm/m)
|
||||
#define HOMING_FEEDRATE_XY (40*60)
|
||||
#define HOMING_FEEDRATE_Z (10*60)
|
||||
#define HOMING_FEEDRATE_XY (50*60)
|
||||
#define HOMING_FEEDRATE_Z (4*60)
|
||||
|
||||
// Validate that endstops are triggered on homing moves
|
||||
#define VALIDATE_HOMING_ENDSTOPS
|
||||
@ -1408,7 +1399,7 @@
|
||||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
@ -1446,12 +1437,12 @@
|
||||
#define PREHEAT_1_LABEL "PLA"
|
||||
#define PREHEAT_1_TEMP_HOTEND 180
|
||||
#define PREHEAT_1_TEMP_BED 70
|
||||
#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_LABEL "ABS"
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_BED 100
|
||||
#define PREHEAT_2_FAN_SPEED 255 // Value from 0 to 255
|
||||
#define PREHEAT_2_TEMP_BED 110
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
/**
|
||||
* Nozzle Park
|
||||
@ -1747,7 +1738,7 @@
|
||||
//
|
||||
// ULTIMAKER Controller.
|
||||
//
|
||||
#define ULTIMAKERCONTROLLER
|
||||
//#define ULTIMAKERCONTROLLER
|
||||
|
||||
//
|
||||
// ULTIPANEL as seen on Thingiverse.
|
||||
|
||||
@ -114,7 +114,7 @@
|
||||
#endif
|
||||
|
||||
#if DISABLED(PIDTEMPBED)
|
||||
#define BED_CHECK_INTERVAL 3000 // ms between checks in bang-bang control
|
||||
#define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
|
||||
#if ENABLED(BED_LIMIT_SWITCHING)
|
||||
#define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
|
||||
#endif
|
||||
@ -215,7 +215,7 @@
|
||||
#endif
|
||||
|
||||
// Show extra position information with 'M114 D'
|
||||
#define M114_DETAIL
|
||||
//#define M114_DETAIL
|
||||
|
||||
// Show Temperature ADC value
|
||||
// Enable for M105 to include ADC values read from temperature sensors.
|
||||
@ -257,7 +257,7 @@
|
||||
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 190
|
||||
#define EXTRUDER_RUNOUT_SECONDS 30
|
||||
#define EXTRUDER_RUNOUT_SPEED 180 // (mm/m)
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m)
|
||||
#define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm)
|
||||
#endif
|
||||
|
||||
@ -516,9 +516,9 @@
|
||||
// @section homing
|
||||
|
||||
// Homing hits each endstop, retracts by these distances, then does a slower bump.
|
||||
#define X_HOME_BUMP_MM 3
|
||||
#define Y_HOME_BUMP_MM 3
|
||||
#define Z_HOME_BUMP_MM 3
|
||||
#define X_HOME_BUMP_MM 5
|
||||
#define Y_HOME_BUMP_MM 5
|
||||
#define Z_HOME_BUMP_MM 2
|
||||
#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
|
||||
//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing
|
||||
@ -635,7 +635,7 @@
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
|
||||
// Time can be set by M18 and M84.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 240
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 120
|
||||
#define DISABLE_INACTIVE_X true
|
||||
#define DISABLE_INACTIVE_Y true
|
||||
#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished.
|
||||
@ -650,7 +650,7 @@
|
||||
#define DEFAULT_MINSEGMENTTIME 20000 // (ms)
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
//#define SLOWDOWN
|
||||
#define SLOWDOWN
|
||||
|
||||
// Frequency limit
|
||||
// See nophead's blog for more info
|
||||
@ -824,7 +824,7 @@
|
||||
// @section lcd
|
||||
|
||||
#if EITHER(ULTIPANEL, EXTENSIBLE_UI)
|
||||
#define MANUAL_FEEDRATE { 50*60, 50*60, 10*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm)
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position"
|
||||
@ -919,7 +919,7 @@
|
||||
|
||||
//#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files
|
||||
|
||||
//#define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27")
|
||||
#define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27")
|
||||
|
||||
/**
|
||||
* Continue after Power-Loss (Creality3D)
|
||||
@ -1587,7 +1587,7 @@
|
||||
#endif
|
||||
#define RETRACT_LENGTH 3 // (mm) Default retract length (positive value)
|
||||
#define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value)
|
||||
#define RETRACT_FEEDRATE 35 // (mm/s) Default feedrate for retracting
|
||||
#define RETRACT_FEEDRATE 45 // (mm/s) Default feedrate for retracting
|
||||
#define RETRACT_ZRAISE 0 // (mm) Default retract Z-raise
|
||||
#define RETRACT_RECOVER_LENGTH 0 // (mm) Default additional recover length (added to retract length on recover)
|
||||
#define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange)
|
||||
@ -1983,7 +1983,7 @@
|
||||
* M912 - Clear stepper driver overtemperature pre-warn condition flag.
|
||||
* M122 - Report driver parameters (Requires TMC_DEBUG)
|
||||
*/
|
||||
#define MONITOR_DRIVER_STATUS
|
||||
//#define MONITOR_DRIVER_STATUS
|
||||
|
||||
#if ENABLED(MONITOR_DRIVER_STATUS)
|
||||
#define CURRENT_STEP_DOWN 50 // [mA]
|
||||
@ -1998,7 +1998,7 @@
|
||||
* STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
|
||||
* M913 X/Y/Z/E to live tune the setting
|
||||
*/
|
||||
#define HYBRID_THRESHOLD
|
||||
//#define HYBRID_THRESHOLD
|
||||
|
||||
#define X_HYBRID_THRESHOLD 100 // [mm/s]
|
||||
#define X2_HYBRID_THRESHOLD 100
|
||||
@ -2037,7 +2037,7 @@
|
||||
* IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when
|
||||
* homing and adds a guard period for endstop triggering.
|
||||
*/
|
||||
#define SENSORLESS_HOMING // StallGuard capable drivers only
|
||||
//#define SENSORLESS_HOMING // StallGuard capable drivers only
|
||||
|
||||
/**
|
||||
* Use StallGuard2 to probe the bed with the nozzle.
|
||||
@ -2061,7 +2061,7 @@
|
||||
* Beta feature!
|
||||
* Create a 50/50 square wave step pulse optimal for stepper drivers.
|
||||
*/
|
||||
#define SQUARE_WAVE_STEPPING
|
||||
//#define SQUARE_WAVE_STEPPING
|
||||
|
||||
/**
|
||||
* Enable M122 debugging command for TMC stepper drivers.
|
||||
@ -2511,8 +2511,8 @@
|
||||
#define USER_DESC_4 "Heat Bed/Home/Level"
|
||||
#define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
|
||||
|
||||
//#define USER_DESC_5 "Home & Info"
|
||||
//#define USER_GCODE_5 "G28\nM503"
|
||||
#define USER_DESC_5 "Home & Info"
|
||||
#define USER_GCODE_5 "G28\nM503"
|
||||
#endif
|
||||
|
||||
/**
|
||||
|
||||
Loading…
Reference in New Issue
Block a user