Add Anet A2 and A2 Plus Configurations (#11677)
This commit is contained in:
Michael Triffon
committed by
Scott Lahteine
Scott Lahteine
parent
72fdb6bab3
commit
aefc2f7cf9
1956
Marlin/src/config/examples/Anet/A2/Configuration.h
Normal file
1956
Marlin/src/config/examples/Anet/A2/Configuration.h
Normal file
File diff suppressed because it is too large
Load Diff
1689
Marlin/src/config/examples/Anet/A2/Configuration_adv.h
Normal file
1689
Marlin/src/config/examples/Anet/A2/Configuration_adv.h
Normal file
File diff suppressed because it is too large
Load Diff
@@ -74,7 +74,7 @@
|
||||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||||
// build by the user have been successfully uploaded into firmware.
|
||||
#define STRING_CONFIG_H_AUTHOR "(Florian S, ANET A2 config 26.8.18)" // Who made the changes.
|
||||
#define STRING_CONFIG_H_AUTHOR "(Modmike, Anet A2 Plus)" // Who made the changes.
|
||||
#define SHOW_BOOTSCREEN
|
||||
#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
|
||||
#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2
|
||||
@@ -125,7 +125,7 @@
|
||||
*
|
||||
* :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000]
|
||||
*/
|
||||
#define BAUDRATE 115200
|
||||
#define BAUDRATE 250000
|
||||
|
||||
// Enable the Bluetooth serial interface on AT90USB devices
|
||||
//#define BLUETOOTH
|
||||
@@ -133,7 +133,7 @@
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
#define MOTHERBOARD BOARD_ANET_10
|
||||
#endif
|
||||
|
||||
// Optional custom name for your RepStrap or other custom machine
|
||||
@@ -151,7 +151,7 @@
|
||||
#define EXTRUDERS 1
|
||||
|
||||
// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
|
||||
|
||||
// For Cyclops or any "multi-extruder" that shares a single nozzle.
|
||||
//#define SINGLENOZZLE
|
||||
@@ -228,7 +228,6 @@
|
||||
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (mm) relative Y-offset for each nozzle
|
||||
//#define HOTEND_OFFSET_Z {0.0, 0.00} // (mm) relative Z-offset for each nozzle
|
||||
|
||||
|
||||
// @section machine
|
||||
|
||||
/**
|
||||
@@ -312,12 +311,12 @@
|
||||
*
|
||||
* :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
|
||||
*/
|
||||
#define TEMP_SENSOR_0 11
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_4 0
|
||||
#define TEMP_SENSOR_BED 11
|
||||
#define TEMP_SENSOR_BED 5
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
@@ -352,12 +351,12 @@
|
||||
// When temperature exceeds max temp, your heater will be switched off.
|
||||
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
||||
// You should use MINTEMP for thermistor short/failure protection.
|
||||
#define HEATER_0_MAXTEMP 250
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
#define HEATER_4_MAXTEMP 275
|
||||
#define BED_MAXTEMP 130
|
||||
#define BED_MAXTEMP 150
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
@@ -382,9 +381,9 @@
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
|
||||
// Ultimaker
|
||||
//#define DEFAULT_Kp 22.2
|
||||
//#define DEFAULT_Ki 1.08
|
||||
//#define DEFAULT_Kd 114
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
//#define DEFAULT_Kp 7.0
|
||||
@@ -396,11 +395,6 @@
|
||||
//#define DEFAULT_Ki 2.25
|
||||
//#define DEFAULT_Kd 440
|
||||
|
||||
// Default A2
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
|
||||
#endif // PIDTEMP
|
||||
|
||||
//===========================================================================
|
||||
@@ -438,9 +432,9 @@
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
//#define DEFAULT_bedKp 10.00
|
||||
//#define DEFAULT_bedKi .023
|
||||
//#define DEFAULT_bedKd 305.4
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
|
||||
//120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
@@ -448,12 +442,6 @@
|
||||
//#define DEFAULT_bedKi 1.41
|
||||
//#define DEFAULT_bedKd 1675.16
|
||||
|
||||
// ANET A2
|
||||
// original Bed + 0.3mm Heat conducting into 4mm borosilicate (PID-Autotune: M303 E-1 S60 C5):
|
||||
#define DEFAULT_bedKp 295.00
|
||||
#define DEFAULT_bedKi 35.65
|
||||
#define DEFAULT_bedKd 610.21
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#endif // PIDTEMPBED
|
||||
|
||||
@@ -554,9 +542,9 @@
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
|
||||
@@ -634,25 +622,14 @@
|
||||
* Override with M92
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
//#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
|
||||
|
||||
// ANET A2 Firmwae V2.0 defaults: (steps/mm)
|
||||
// Xsteps/mm: +100.0, Ysteps/mm: +100.0, Zsteps/mm: +0400.0, eSteps/mm: +0095.0
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 400, 95}
|
||||
//#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 400, 95}
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 400, 95 }
|
||||
|
||||
/**
|
||||
* Default Max Feed Rate (mm/s)
|
||||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
//#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
|
||||
// ANET A2 Firmware V2.0 defaults (Vmax):
|
||||
// Vmax x: 400, Vmax y: 400, Vmax z: 4, Vmax e: 25
|
||||
#define DEFAULT_MAX_FEEDRATE {400, 400, 4, 25}
|
||||
//#define DEFAULT_MAX_FEEDRATE {400, 400, 20, 50}
|
||||
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
|
||||
/**
|
||||
* Default Max Acceleration (change/s) change = mm/s
|
||||
@@ -660,12 +637,7 @@
|
||||
* Override with M201
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
//#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
|
||||
// ANET A2 Firmware V2.0 defaults (Amax):
|
||||
// Amx x: 9000, Amax Y: 5000, Amax z: 50, Amax e: 10000
|
||||
#define DEFAULT_MAX_ACCELERATION { 9000, 5000, 50, 10000 }
|
||||
//#define DEFAULT_MAX_ACCELERATION { 10000, 10000, 200, 10000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
|
||||
/**
|
||||
* Default Acceleration (change/s) change = mm/s
|
||||
@@ -675,19 +647,9 @@
|
||||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
//#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
//#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
//#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
// ANET A2 Firmware V2.0 defaults:
|
||||
// Accel: 1000 A-retract: 1000
|
||||
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
//#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration for printing moves
|
||||
//#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts
|
||||
//#define DEFAULT_TRAVEL_ACCELERATION 4000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
/**
|
||||
* Default Jerk (mm/s)
|
||||
@@ -697,12 +659,10 @@
|
||||
* When changing speed and direction, if the difference is less than the
|
||||
* value set here, it may happen instantaneously.
|
||||
*/
|
||||
// ANET A2 Firmware V2.0 defaults (jerk):
|
||||
// Vxy-jerk: 20, Vz-jerk: +000.30, Ve-jerk: 10
|
||||
#define DEFAULT_XJERK 20.0
|
||||
#define DEFAULT_YJERK 20.0
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_ZJERK 0.3
|
||||
#define DEFAULT_EJERK 10.0
|
||||
#define DEFAULT_EJERK 5.0
|
||||
|
||||
/**
|
||||
* S-Curve Acceleration
|
||||
@@ -728,7 +688,7 @@
|
||||
*
|
||||
* Enable this option for a probe connected to the Z Min endstop pin.
|
||||
*/
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
/**
|
||||
* Z_MIN_PROBE_ENDSTOP
|
||||
@@ -763,7 +723,7 @@
|
||||
* Use G29 repeatedly, adjusting the Z height at each point with movement commands
|
||||
* or (with LCD_BED_LEVELING) the LCD controller.
|
||||
*/
|
||||
#define PROBE_MANUALLY
|
||||
//#define PROBE_MANUALLY
|
||||
//#define MANUAL_PROBE_START_Z 0.2
|
||||
|
||||
/**
|
||||
@@ -793,11 +753,11 @@
|
||||
* These options are most useful for the BLTouch probe, but may also improve
|
||||
* readings with inductive probes and piezo sensors.
|
||||
*/
|
||||
#define PROBING_HEATERS_OFF // Turn heaters off when probing
|
||||
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
|
||||
#if ENABLED(PROBING_HEATERS_OFF)
|
||||
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
|
||||
#endif
|
||||
#define PROBING_FANS_OFF // Turn fans off when probing
|
||||
//#define PROBING_FANS_OFF // Turn fans off when probing
|
||||
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
|
||||
|
||||
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
|
||||
@@ -834,28 +794,22 @@
|
||||
//#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle]
|
||||
//#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
|
||||
|
||||
//ANET A2 with BLTouch/3D-Touch mounted right to the nozzle
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER 39 // X offset: -left +right [of the nozzle]
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0 // Y offset: -front +behind [the nozzle]
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
|
||||
|
||||
// Certain types of probes need to stay away from edges
|
||||
#define MIN_PROBE_EDGE 10
|
||||
//#define MIN_PROBE_EDGE 10
|
||||
|
||||
// X and Y axis travel speed (mm/m) between probes
|
||||
#define XY_PROBE_SPEED 8000
|
||||
//#define XY_PROBE_SPEED 6000
|
||||
//#define XY_PROBE_SPEED 8000
|
||||
|
||||
// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
|
||||
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
|
||||
//#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
|
||||
|
||||
// Feedrate (mm/m) for the "accurate" probe of each point
|
||||
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 3)
|
||||
//#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
|
||||
|
||||
// The number of probes to perform at each point.
|
||||
// Set to 2 for a fast/slow probe, using the second probe result.
|
||||
// Set to 3 or more for slow probes, averaging the results.
|
||||
#define MULTIPLE_PROBING 2
|
||||
//#define MULTIPLE_PROBING 2
|
||||
|
||||
/**
|
||||
* Z probes require clearance when deploying, stowing, and moving between
|
||||
@@ -871,17 +825,10 @@
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#if 1 // 0 for less clearance
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||
#else
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 3 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
//#define Z_AFTER_PROBING 3 // Z position after probing is done
|
||||
#endif
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||
|
||||
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
|
||||
|
||||
@@ -915,17 +862,14 @@
|
||||
// @section machine
|
||||
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
//#define INVERT_Y_DIR true
|
||||
//#define INVERT_Z_DIR false
|
||||
//ANET A2:
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
#define INVERT_X_DIR true
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR true
|
||||
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E0_DIR true
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
@@ -949,36 +893,16 @@
|
||||
// @section machine
|
||||
|
||||
// The size of the print bed
|
||||
//#define X_BED_SIZE 200
|
||||
//#define Y_BED_SIZE 200
|
||||
#define X_BED_SIZE 220
|
||||
#define Y_BED_SIZE 270
|
||||
|
||||
// Travel limits (mm) after homing, corresponding to endstop positions.
|
||||
//#define X_MIN_POS 0
|
||||
//#define Y_MIN_POS 0
|
||||
//#define X_MAX_POS X_BED_SIZE
|
||||
//#define Y_MAX_POS Y_BED_SIZE
|
||||
//#define Z_MIN_POS 0
|
||||
//#define Z_MAX_POS 200
|
||||
|
||||
// ANET A2 Firmware V2.0 defaults:
|
||||
//#define X_BED_SIZE 220
|
||||
//#define Y_BED_SIZE 270
|
||||
//#define X_MIN_POS 0
|
||||
//#define Y_MIN_POS 0
|
||||
//#define Z_MIN_POS 0
|
||||
//#define Z_MAX_POS 220
|
||||
|
||||
// ANET A2 with glass bed clamps and safety margin, X0/Y0 0 front left bed edge:
|
||||
#define X_BED_SIZE 190
|
||||
#define Y_BED_SIZE 250
|
||||
#define X_MIN_POS -7
|
||||
#define Y_MIN_POS -5
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MIN_POS 0
|
||||
#define Z_MAX_POS 180
|
||||
|
||||
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
|
||||
/**
|
||||
* Software Endstops
|
||||
@@ -1068,13 +992,13 @@
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
#define MESH_BED_LEVELING
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
* Normally G28 leaves leveling disabled on completion. Enable
|
||||
* this option to have G28 restore the prior leveling state.
|
||||
*/
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
//#define RESTORE_LEVELING_AFTER_G28
|
||||
|
||||
/**
|
||||
* Enable detailed logging of G28, G29, M48, etc.
|
||||
@@ -1111,14 +1035,14 @@
|
||||
#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR)
|
||||
|
||||
// Set the number of grid points per dimension.
|
||||
#define GRID_MAX_POINTS_X 4
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
// Set the boundaries for probing (where the probe can reach).
|
||||
//#define LEFT_PROBE_BED_POSITION 15
|
||||
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - 15)
|
||||
//#define FRONT_PROBE_BED_POSITION 15
|
||||
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - 15)
|
||||
//#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE
|
||||
//#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - MIN_PROBE_EDGE)
|
||||
//#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE
|
||||
//#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - MIN_PROBE_EDGE)
|
||||
|
||||
// Probe along the Y axis, advancing X after each column
|
||||
//#define PROBE_Y_FIRST
|
||||
@@ -1166,10 +1090,10 @@
|
||||
//===========================================================================
|
||||
|
||||
#define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed
|
||||
#define GRID_MAX_POINTS_X 5 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited.
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
|
||||
|
||||
#endif // BED_LEVELING
|
||||
|
||||
@@ -1190,7 +1114,7 @@
|
||||
* Add a bed leveling sub-menu for ABL or MBL.
|
||||
* Include a guided procedure if manual probing is enabled.
|
||||
*/
|
||||
#define LCD_BED_LEVELING
|
||||
//#define LCD_BED_LEVELING
|
||||
|
||||
#if ENABLED(LCD_BED_LEVELING)
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
|
||||
@@ -1232,7 +1156,7 @@
|
||||
// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28).
|
||||
// - Prevent Z homing when the Z probe is outside bed area.
|
||||
//
|
||||
#define Z_SAFE_HOMING
|
||||
//#define Z_SAFE_HOMING
|
||||
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28).
|
||||
@@ -1314,7 +1238,7 @@
|
||||
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
||||
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
||||
//
|
||||
#define EEPROM_SETTINGS // Enable for M500 and M501 commands
|
||||
#define EEPROM_SETTINGS // Enable for M500 and M501 commands
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
|
||||
@@ -1348,11 +1272,11 @@
|
||||
// Preheat Constants
|
||||
#define PREHEAT_1_TEMP_HOTEND 200
|
||||
#define PREHEAT_1_TEMP_BED 60
|
||||
#define PREHEAT_1_FAN_SPEED 0 // ANET A2 default is 255
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_BED 80
|
||||
#define PREHEAT_2_FAN_SPEED 0 // ANET A2 default is 255
|
||||
#define PREHEAT_2_TEMP_HOTEND 230
|
||||
#define PREHEAT_2_TEMP_BED 100
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
/**
|
||||
* Nozzle Park
|
||||
@@ -1365,7 +1289,7 @@
|
||||
* P1 Raise the nozzle always to Z-park height.
|
||||
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
||||
*/
|
||||
#define NOZZLE_PARK_FEATURE
|
||||
//#define NOZZLE_PARK_FEATURE
|
||||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z }
|
||||
@@ -1465,7 +1389,7 @@
|
||||
*
|
||||
* View the current statistics with M78.
|
||||
*/
|
||||
#define PRINTCOUNTER
|
||||
//#define PRINTCOUNTER
|
||||
|
||||
//=============================================================================
|
||||
//============================= LCD and SD support ============================
|
||||
@@ -1588,7 +1512,7 @@
|
||||
//
|
||||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||||
//
|
||||
#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
|
||||
//
|
||||
// SPEAKER/BUZZER
|
||||
@@ -1848,7 +1772,7 @@
|
||||
//
|
||||
// ANET and Tronxy Graphical Controller
|
||||
//
|
||||
#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
|
||||
#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
|
||||
// A clone of the RepRapDiscount full graphics display but with
|
||||
// different pins/wiring (see pins_ANET_10.h).
|
||||
|
||||
|
||||
@@ -75,8 +75,8 @@
|
||||
* THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 60 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 10 // Degrees Celsius
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
|
||||
|
||||
/**
|
||||
* Whenever an M104, M109, or M303 increases the target temperature, the
|
||||
@@ -90,21 +90,21 @@
|
||||
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
|
||||
* below 2.
|
||||
*/
|
||||
#define WATCH_TEMP_PERIOD 60 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 5 // Degrees Celsius
|
||||
#define WATCH_TEMP_PERIOD 20 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Thermal Protection parameters for the bed are just as above for hotends.
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_BED)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 60 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 5 // Degrees Celsius
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
|
||||
/**
|
||||
* As described above, except for the bed (M140/M190/M303).
|
||||
*/
|
||||
#define WATCH_BED_TEMP_PERIOD 180 // Seconds
|
||||
#define WATCH_BED_TEMP_PERIOD 60 // Seconds
|
||||
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
@@ -128,7 +128,7 @@
|
||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
*/
|
||||
//#define AUTOTEMP
|
||||
#define AUTOTEMP
|
||||
#if ENABLED(AUTOTEMP)
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
#endif
|
||||
@@ -477,7 +477,7 @@
|
||||
* known compatible chips: AD5206
|
||||
* DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2
|
||||
* known compatible chips: MCP4728
|
||||
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, MIGHTYBOARD_REVE
|
||||
* DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE
|
||||
* known compatible chips: MCP4451, MCP4018
|
||||
*
|
||||
* Motor currents can also be set by M907 - M910 and by the LCD.
|
||||
@@ -525,7 +525,7 @@
|
||||
// @section lcd
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
#define LCD_INFO_MENU
|
||||
//#define LCD_INFO_MENU
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
@@ -574,7 +574,7 @@
|
||||
// as SD_DETECT_PIN in your board's pins definitions.
|
||||
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
|
||||
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
|
||||
//#define SD_DETECT_INVERTED
|
||||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
@@ -749,9 +749,9 @@
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
#define BABYSTEP_MULTIPLICATOR 5 // Babysteps are very small. Increase for faster motion.
|
||||
#define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
|
||||
//#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
//#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
@@ -820,7 +820,7 @@
|
||||
//
|
||||
// G2/G3 Arc Support
|
||||
//
|
||||
//#define ARC_SUPPORT // Disable this feature to save ~3226 bytes
|
||||
#define ARC_SUPPORT // Disable this feature to save ~3226 bytes
|
||||
#if ENABLED(ARC_SUPPORT)
|
||||
#define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
|
||||
#define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
|
||||
@@ -1003,7 +1003,7 @@
|
||||
* Requires NOZZLE_PARK_FEATURE.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
|
||||
@@ -745,7 +745,7 @@
|
||||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
|
||||
@@ -745,7 +745,7 @@
|
||||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
|
||||
Reference in New Issue
Block a user