Merge pull request #8547 from thinkyhead/bf2_babystep_gfx_overlay

[2.0.x] Followup for MESH_EDIT_GFX_OVERLAY

.travis.yml

@@ -292,7 +292,7 @@ script:
   #
   - use_example_configs delta/generic
   - opt_disable DISABLE_MIN_ENDSTOPS
-  - opt_enable AUTO_BED_LEVELING_UBL Z_PROBE_ALLEN_KEY EEPROM_SETTINGS EEPROM_CHITCHAT OLED_PANEL_TINYBOY2
+  - opt_enable AUTO_BED_LEVELING_UBL Z_PROBE_ALLEN_KEY EEPROM_SETTINGS EEPROM_CHITCHAT OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY
   - build_marlin_pio ${TRAVIS_BUILD_DIR} ${TEST_PLATFORM}
   #
   # Delta Config (FLSUN AC because it's complex)

Marlin/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/Configuration_adv.h

@@ -611,6 +611,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/default/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/default/Configuration_adv.h

@@ -611,6 +611,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h

@@ -899,7 +899,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -973,6 +972,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/AliExpress/CL-260/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Anet/A6/Configuration.h

@@ -998,7 +998,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1096,6 +1095,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Anet/A6/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Anet/A8/Configuration.h

@@ -885,7 +885,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -959,6 +958,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Anet/A8/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Azteeg/X5GT/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h

@@ -612,6 +612,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/Hephestos/Configuration.h

@@ -870,7 +870,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -944,6 +943,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h

@@ -880,7 +880,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -954,6 +953,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -607,6 +607,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -641,7 +645,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/BQ/WITBOX/Configuration.h

@@ -870,7 +870,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -944,6 +943,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Cartesio/Configuration.h

@@ -878,7 +878,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -952,6 +951,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Cartesio/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Creality/CR-10/Configuration.h

@@ -889,7 +889,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -963,6 +962,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Felix/Configuration.h

@@ -861,7 +861,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -935,6 +934,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Felix/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Felix/DUAL/Configuration.h

@@ -861,7 +861,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -935,6 +934,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h

@@ -876,7 +876,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -950,6 +949,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y 10

Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -611,6 +611,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Geeetech/GT2560/Configuration.h

@@ -894,7 +894,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -968,6 +967,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Infitary/i3-M508/Configuration.h

@@ -883,7 +883,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -957,6 +956,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Malyan/M150/Configuration.h

@@ -907,7 +907,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -981,6 +980,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Malyan/M150/Configuration_adv.h

@@ -604,6 +604,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -638,7 +642,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Micromake/C1/basic/Configuration.h

@@ -883,7 +883,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -957,6 +956,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h

@@ -883,7 +883,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -957,6 +956,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -611,6 +611,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Mks/Sbase/Configuration.h

@@ -880,7 +880,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -954,6 +953,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h

@@ -612,6 +612,10 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
+
   // VIKI2 and miniVIKI require DOGLCD_SCK and DOGLCD_MOSI to be defined.
   #if ENABLED(VIKI2) || ENABLED(miniVIKI)
     #define DOGLCD_SCK SCK_PIN
@@ -652,7 +656,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/RigidBot/Configuration.h

@@ -877,7 +877,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -951,6 +950,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/RigidBot/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/SCARA/Configuration.h

@@ -891,7 +891,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -965,6 +964,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/SCARA/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/STM32F10/Configuration.h

@@ -882,7 +882,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -956,6 +955,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Sanguinololu/Configuration.h

@@ -910,7 +910,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -984,6 +983,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Sanguinololu/Configuration_adv.h

@@ -599,6 +599,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -633,7 +637,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/TinyBoy2/Configuration.h

@@ -935,7 +935,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1009,6 +1008,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/TinyBoy2/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/UltiMachine/Archim2/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -611,6 +611,9 @@
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
 
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8200/Configuration.h

@@ -909,7 +909,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -983,6 +982,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h

@@ -618,6 +618,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -652,7 +656,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8400/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h

@@ -611,6 +611,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/adafruit/ST7565/Configuration.h

@@ -879,7 +879,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -953,6 +952,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -1009,7 +1009,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1085,6 +1084,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -1009,7 +1009,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1079,6 +1078,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/generic/Configuration.h

@@ -996,7 +996,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1073,6 +1072,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/generic/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_mini/Configuration.h

@@ -999,7 +999,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1076,6 +1075,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_pro/Configuration.h

@@ -999,7 +999,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1076,6 +1075,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h

@@ -617,6 +617,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -651,7 +655,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/delta/kossel_xl/Configuration.h

@@ -1008,7 +1008,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -1085,6 +1084,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h

@@ -612,6 +612,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -646,7 +650,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h

@@ -893,7 +893,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 #define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -967,6 +966,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 45             // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/makibox/Configuration.h

@@ -882,7 +882,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -956,6 +955,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/makibox/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/tvrrug/Round2/Configuration.h

@@ -874,7 +874,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -948,6 +947,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h

@@ -610,6 +610,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -644,7 +648,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/config/examples/wt150/Configuration.h

@@ -884,7 +884,6 @@
  * NOTE: Requires a lot of PROGMEM!
  */
 //#define DEBUG_LEVELING_FEATURE
-//#define ENABLE_MESH_EDIT_GFX_OVERLAY  // enable a graphics overly while editing the mesh from auto-level
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Gradually reduce leveling correction until a set height is reached,
@@ -958,6 +957,8 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
+  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+
   #define MESH_INSET 1              // Mesh inset margin on print area
   #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X

Marlin/src/config/examples/wt150/Configuration_adv.h

@@ -611,6 +611,10 @@
   // Enable this option and reduce the value to optimize screen updates.
   // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
   //#define DOGM_SPI_DELAY_US 5
+
+  // Swap the CW/CCW indicators in the graphics overlay
+  //#define OVERLAY_GFX_REVERSE
+
 #endif // DOGLCD
 
 // @section safety
@@ -645,7 +649,6 @@
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
   //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
-  //#define BABYSTEP_ZPROBE_GFX_REVERSE // Reverses the direction of the CW/CCW indicators
 #endif
 
 // @section extruder

Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp

@@ -1009,11 +1009,9 @@
             SERIAL_PROTOCOLLNPGM("\nMesh only partially populated.");
             do_blocking_move_to_z(Z_CLEARANCE_DEPLOY_PROBE);
 
-            #if ENABLED(NEWPANEL)
             lcd_quick_feedback();
             while (is_lcd_clicked()) idle();
             lcd_external_control = false;
-            #endif
 
             KEEPALIVE_STATE(IN_HANDLER);
             restore_ubl_active_state_and_leave();

Marlin/src/gcode/bedlevel/G26.cpp

@@ -517,13 +517,11 @@ bool prime_nozzle() {
 
       while (is_lcd_clicked()) idle();           // Debounce Encoder Wheel
 
-      #if ENABLED(ULTRA_LCD)
       strcpy_P(lcd_status_message, PSTR("Done Priming")); // We can't do lcd_setstatusPGM() without having it continue;
                                                           // So... We cheat to get a message up.
       lcd_setstatusPGM(PSTR("Done Priming"), 99);
       lcd_quick_feedback();
       lcd_external_control = false;
-      #endif
     }
     else
   #endif

Marlin/src/gcode/motion/G0_G1.cpp

@@ -31,6 +31,10 @@
 
 #include "../../sd/cardreader.h"
 
+#if ENABLED(NANODLP_Z_SYNC)
+  #include "../../module/stepper.h"
+#endif
+
 extern float destination[XYZE];
 
 #if ENABLED(NO_MOTION_BEFORE_HOMING)

Marlin/src/inc/SanityCheck.h

@@ -219,6 +219,10 @@
   #error "UBL_MESH_INSET is now just MESH_INSET. Please update your configuration."
 #elif defined(UBL_MESH_MIN_X) || defined(UBL_MESH_MIN_Y) || defined(UBL_MESH_MAX_X)  || defined(UBL_MESH_MAX_Y)
   #error "UBL_MESH_(MIN|MAX)_[XY] is now just MESH_(MIN|MAX)_[XY]. Please update your configuration."
+#elif defined(ENABLE_MESH_EDIT_GFX_OVERLAY)
+  #error "ENABLE_MESH_EDIT_GFX_OVERLAY is now MESH_EDIT_GFX_OVERLAY. Please update your configuration."
+#elif defined(BABYSTEP_ZPROBE_GFX_REVERSE)
+  #error "BABYSTEP_ZPROBE_GFX_REVERSE is now set by OVERLAY_GFX_REVERSE. Please update your configurations."
 #endif
 
 /**
@@ -760,9 +764,6 @@ static_assert(1 >= 0
     static_assert(WITHIN(UBL_PROBE_PT_2_Y, MIN_PROBE_Y, MAX_PROBE_Y), "UBL_PROBE_PT_2_Y can't be reached by the Z probe.");
     static_assert(WITHIN(UBL_PROBE_PT_3_Y, MIN_PROBE_Y, MAX_PROBE_Y), "UBL_PROBE_PT_3_Y can't be reached by the Z probe.");
   #endif
-  #if ENABLED(ENABLE_MESH_EDIT_GFX_OVERLAY) && !ENABLED(DOGLCD)
-    #error "ENABLE_MESH_EDIT_GFX_OVERLAY requires a DOGLCD."
-  #endif
 
 #elif OLDSCHOOL_ABL
 
@@ -832,6 +833,10 @@ static_assert(1 >= 0
   #error "G26_MESH_VALIDATION requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_UBL."
 #endif
 
+#if ENABLED(MESH_EDIT_GFX_OVERLAY) && (DISABLED(AUTO_BED_LEVELING_UBL) || DISABLED(DOGLCD))
+  #error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD."
+#endif
+
 /**
  * LCD_BED_LEVELING requirements
  */

Marlin/src/lcd/dogm/dogm_bitmaps.h

@@ -420,76 +420,77 @@
     };
   #endif // Extruders
 #endif // HAS_TEMP_BED
-#if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(ENABLE_MESH_EDIT_GFX_OVERLAY)
+
+#if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(MESH_EDIT_GFX_OVERLAY)
+
   const unsigned char cw_bmp[] PROGMEM = { //AVR-GCC, WinAVR
-    0x07,0xf8,0x00, // 000001111111100000000000
+    0x03,0xF8,0x00, // 000000111111100000000000
-    0x0c,0x0c,0x00, // 000011000000110000000000
+    0x0F,0xF7,0x00, // 000011111111111000000000
-    0x10,0x02,0x00, // 000100000000001000000000
+    0x17,0x0F,0x00, // 000111100000111100000000
-    0x20,0x01,0x00, // 001000000000000100000000
+    0x38,0x07,0x00, // 001110000000011100000000
-    0x60,0x01,0x80, // 011000000000000100000000
+    0x38,0x03,0x80, // 001110000000001110000000
-    0x40,0x00,0x80, // 010000000000000010000000
+    0x70,0x03,0x80, // 011100000000001110000000
-    0x40,0x03,0xe0, // 010000000000001111100000
+    0x70,0x0F,0xE0, // 011100000000111111100000
-    0x40,0x01,0xc0, // 010000000000000111000000
+    0x70,0x07,0xC0, // 011100000000011111000000
-    0x40,0x00,0x80, // 010000000000000010000000
+    0x70,0x03,0x80, // 011100000000001110000000
-    0x40,0x00,0x00, // 010000000000000000000000
+    0x70,0x01,0x00, // 011100000000000100000000
-    0x40,0x00,0x00, // 010000000000000000000000
+    0x70,0x00,0x00, // 011100000000000000000000
-    0x60,0x00,0x00, // 011000000000000000000000
+    0x68,0x00,0x00, // 001110000000000000000000
-    0x20,0x00,0x00, // 001000000000000000000000
+    0x38,0x07,0x00, // 001110000000011100000000
-    0x10,0x00,0x00, // 000100000000000000000000
+    0x17,0x0F,0x00, // 000111100000111100000000
-    0x0c,0x0c,0x00, // 000011000000110000000000
+    0x0F,0xFE,0x00, // 000011111111111000000000
-    0x07,0xf8,0x00  // 000001111111100000000000
+    0x03,0xF8,0x00  // 000000111111100000000000
   };
 
   const unsigned char ccw_bmp[] PROGMEM = { //AVR-GCC, WinAVR
-    0x01,0xfe,0x00, // 000000011111111000000000
+    0x00,0xFE,0x00, // 000000001111111000000000
-    0x03,0x03,0x00, // 000000110000001100000000
+    0x03,0xFF,0x80, // 000000111111111110000000
-    0x04,0x00,0x80, // 000001000000000010000000
+    0x07,0x83,0xC0, // 000001111000001111000000
-    0x08,0x00,0x40, // 000010000000000001000000
+    0x0E,0x01,0xC0, // 000011100000000111000000
-    0x18,0x00,0x60, // 000110000000000001100000
+    0x0E,0x00,0xE0, // 000011100000000011100000
-    0x10,0x00,0x20, // 000100000000000000100000
+    0x1C,0x00,0xE0, // 000111000000000011100000
-    0x7c,0x00,0x20, // 011111000000000000100000
+    0x7F,0x00,0xE0, // 011111110000000011100000
-    0x38,0x00,0x20, // 001110000000000000100000
+    0x3E,0x00,0xE0, // 001111100000000011100000
-    0x10,0x00,0x20, // 000100000000000000100000
+    0x1C,0x00,0xE0, // 000111000000000011100000
-    0x00,0x00,0x20, // 000000000000000000100000
+    0x08,0x00,0xE0, // 000010000000000011100000
-    0x00,0x00,0x20, // 000000000000000000100000
+    0x00,0x00,0xE0, // 000000000000000011100000
-    0x00,0x00,0x60, // 000000000000000001100000
+    0x00,0x01,0xC0, // 000000000000000111000000
-    0x00,0x00,0x40, // 000000000000000001000000
+    0x0E,0x01,0xC0, // 000011100000000111000000
-    0x00,0x00,0x80, // 000000000000000010000000
+    0x0F,0x07,0x80, // 000011110000011110000000
-    0x03,0x03,0x00, // 000000110000001100000000
+    0x07,0xFF,0x00, // 000001111111111100000000
-    0x01,0xfe,0x00  // 000000011111111000000000
+    0x01,0xFC,0x00  // 000000011111110000000000
   };
 
-
   const unsigned char up_arrow_bmp[] PROGMEM = { //AVR-GCC, WinAVR
-    0x06,0x00, // 000001100000
+    0x04,0x00, // 000001000000
-    0x0F,0x00, // 000011110000
+    0x0E,0x00, // 000011100000
-    0x1F,0x80, // 000111111000
+    0x1F,0x00, // 000111110000
-    0x3F,0xC0, // 001111111100
+    0x3F,0x80, // 001111111000
-    0x06,0x00, // 000001100000
+    0x7F,0xC0, // 011111111100
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00  // 000001100000
+    0x0E,0x00  // 000011100000
   };
 
   const unsigned char down_arrow_bmp[] PROGMEM = { //AVR-GCC, WinAVR
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x0E,0x00, // 000011100000
-    0x06,0x00, // 000001100000
+    0x7F,0xC0, // 011111111100
-    0x3F,0xC0, // 001111111100
+    0x3F,0x80, // 001111111000
-    0x1F,0x80, // 000111111000
+    0x1F,0x00, // 000111110000
-    0x0F,0x00, // 000011110000
+    0x0E,0x00, // 000011100000
-    0x06,0x00  // 000001100000
+    0x04,0x00  // 000001000000
   };
 
   const unsigned char offset_bedline_bmp[] PROGMEM = { //AVR-GCC, WinAVR
@@ -510,4 +511,5 @@
     0x1E,0x00, // 0001111000000000
     0x0C,0x00  // 0000110000000000
   };
-#endif // BABYSTEP_ZPROBE_GFX_OVERLAY || ENABLE_MESH_EDIT_GFX_OVERLAY
+
+#endif // BABYSTEP_ZPROBE_GFX_OVERLAY || MESH_EDIT_GFX_OVERLAY

Marlin/src/lcd/ultralcd.cpp

@@ -1035,6 +1035,44 @@ void kill_screen(const char* lcd_msg) {
     }
   #endif
 
+  #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(MESH_EDIT_GFX_OVERLAY)
+
+    void _lcd_zoffset_overlay_gfx(const float zvalue) {
+      // Determine whether the user is raising or lowering the nozzle.
+      static int8_t dir;
+      static float old_zvalue;
+      if (zvalue != old_zvalue) {
+        dir = zvalue ? zvalue < old_zvalue ? -1 : 1 : 0;
+        old_zvalue = zvalue;
+      }
+
+      #if ENABLED(OVERLAY_GFX_REVERSE)
+        const unsigned char *rot_up = ccw_bmp, *rot_down = cw_bmp;
+      #else
+        const unsigned char *rot_up = cw_bmp, *rot_down = ccw_bmp;
+      #endif
+
+      #if ENABLED(USE_BIG_EDIT_FONT)
+        const int left = 0, right = 45, nozzle = 95;
+      #else
+        const int left = 5, right = 90, nozzle = 60;
+      #endif
+
+      // Draw a representation of the nozzle
+      if (PAGE_CONTAINS(3, 16))  u8g.drawBitmapP(nozzle + 6, 4 - dir, 2, 12, nozzle_bmp);
+      if (PAGE_CONTAINS(20, 20)) u8g.drawBitmapP(nozzle + 0, 20, 3, 1, offset_bedline_bmp);
+
+      // Draw cw/ccw indicator and up/down arrows.
+      if (PAGE_CONTAINS(47,62)) {
+        u8g.drawBitmapP(left  + 0, 47, 3, 16, rot_down);
+        u8g.drawBitmapP(right + 0, 47, 3, 16, rot_up);
+        u8g.drawBitmapP(right + 20, 48 - dir, 2, 13, up_arrow_bmp);
+        u8g.drawBitmapP(left  + 20, 49 - dir, 2, 13, down_arrow_bmp);
+      }
+    }
+
+  #endif // BABYSTEP_ZPROBE_GFX_OVERLAY || MESH_EDIT_GFX_OVERLAY
+
   #if ENABLED(BABYSTEPPING)
 
     void _lcd_babystep(const AxisEnum axis, const char* msg) {
@@ -1058,46 +1096,6 @@ void kill_screen(const char* lcd_msg) {
       void lcd_babystep_y() { lcd_goto_screen(_lcd_babystep_y); babysteps_done = 0; defer_return_to_status = true; }
     #endif
 
-    #if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(ENABLE_MESH_EDIT_GFX_OVERLAY)
-
-      void _lcd_zoffset_overlay_gfx(const float in_zoffset) {
-        // Determine whether the user is raising or lowering the nozzle.
-        int8_t dir = 0;
-        static float old_zprobe_zoffset = 0;
-        if (in_zoffset != old_zprobe_zoffset) {
-          dir = (in_zoffset > old_zprobe_zoffset) ? 1 : (in_zoffset == 0) ? 0 : -1;
-          old_zprobe_zoffset = in_zoffset;
-        }
-
-        #if ENABLED(BABYSTEP_ZPROBE_GFX_REVERSE)
-          const unsigned char *rot_up   = ccw_bmp;
-          const unsigned char *rot_down = cw_bmp;
-        #else
-          const unsigned char *rot_up   = cw_bmp;
-          const unsigned char *rot_down = ccw_bmp;
-        #endif
-
-        #if ENABLED(USE_BIG_EDIT_FONT)
-          const int left = 0, right = 45, nozzle = 95;
-        #else
-          const int left = 5, right = 90, nozzle = 60;
-        #endif
-
-        // Draw a representation of the nozzle
-        if (PAGE_CONTAINS(3, 16))  u8g.drawBitmapP(nozzle + 6, 4 - dir, 2, 12, nozzle_bmp);
-        if (PAGE_CONTAINS(20, 20)) u8g.drawBitmapP(nozzle + 0, 20, 3, 1, offset_bedline_bmp);
-
-        // Draw cw/ccw indicator and up/down arrows.
-        if (PAGE_CONTAINS(47,62)) {
-          u8g.drawBitmapP(left  + 0, 47, 3, 16, rot_down);
-          u8g.drawBitmapP(right + 0, 47, 3, 16, rot_up);
-          u8g.drawBitmapP(right + 20, 48 - dir, 2, 13, up_arrow_bmp);
-          u8g.drawBitmapP(left  + 20, 49 - dir, 2, 13, down_arrow_bmp);
-        }
-      }
-
-    #endif // BABYSTEP_ZPROBE_GFX_OVERLAY || ENABLE_MESH_EDIT_GFX_OVERLAY
-
     #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
 
       void lcd_babystep_zoffset() {
@@ -1157,7 +1155,7 @@ void kill_screen(const char* lcd_msg) {
 
       if (lcdDrawUpdate)
         lcd_implementation_drawedit(msg, ftostr43sign(mesh_edit_value));
-        #if ENABLED(ENABLE_MESH_EDIT_GFX_OVERLAY)
+        #if ENABLED(MESH_EDIT_GFX_OVERLAY)
           _lcd_zoffset_overlay_gfx(mesh_edit_value);
         #endif
     }
@@ -1194,7 +1192,6 @@ void kill_screen(const char* lcd_msg) {
 
   #endif // AUTO_BED_LEVELING_UBL
 
-
   /**
    * Watch temperature callbacks
    */