Add a ported example configuration for the Velleman K8400 (Vertex) printer.
Supports both dual and single head printers (with the correct config). Includes community sourced feed rate fix. Rename / move files. Remove redundant definitions.
This commit is contained in:
Anthony Birkett
parent
1236a3b3ab
commit
a0b00d29e3
@ -60,7 +60,8 @@
|
||||
#define BOARD_ULTIMAKER_OLD 71 // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
#define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
#define BOARD_3DRAG 77 // 3Drag Controller
|
||||
#define BOARD_K8200 78 // Vellemann K8200 Controller (derived from 3Drag Controller)
|
||||
#define BOARD_K8200 78 // Velleman K8200 Controller (derived from 3Drag Controller)
|
||||
#define BOARD_K8400 79 // Velleman K8400 Controller (derived from 3Drag Controller)
|
||||
#define BOARD_TEENSYLU 8 // Teensylu
|
||||
#define BOARD_RUMBA 80 // Rumba
|
||||
#define BOARD_PRINTRBOARD 81 // Printrboard (AT90USB1286)
|
||||
|
||||
1216
Marlin/example_configurations/K8400/Configuration.h
Normal file
1216
Marlin/example_configurations/K8400/Configuration.h
Normal file
File diff suppressed because it is too large
Load Diff
750
Marlin/example_configurations/K8400/Configuration_adv.h
Normal file
750
Marlin/example_configurations/K8400/Configuration_adv.h
Normal file
@ -0,0 +1,750 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Configuration_adv.h
|
||||
*
|
||||
* Advanced settings.
|
||||
* Only change these if you know exactly what you're doing.
|
||||
* Some of these settings can damage your printer if improperly set!
|
||||
*
|
||||
* Basic settings can be found in Configuration.h
|
||||
*
|
||||
*/
|
||||
#ifndef CONFIGURATION_ADV_H
|
||||
#define CONFIGURATION_ADV_H
|
||||
|
||||
/**
|
||||
*
|
||||
* ***********************************
|
||||
* ** ATTENTION TO ALL DEVELOPERS **
|
||||
* ***********************************
|
||||
*
|
||||
* You must increment this version number for every significant change such as,
|
||||
* but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
|
||||
*
|
||||
* Note: Update also Version.h !
|
||||
*/
|
||||
#define CONFIGURATION_ADV_H_VERSION 010100
|
||||
|
||||
#include "Conditionals.h"
|
||||
|
||||
// @section temperature
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
||||
#if DISABLED(PIDTEMPBED)
|
||||
#define BED_CHECK_INTERVAL 1000 // ms between checks in bang-bang control
|
||||
#if ENABLED(BED_LIMIT_SWITCHING)
|
||||
#define BED_HYSTERESIS 1 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Thermal Protection protects your printer from damage and fire if a
|
||||
* thermistor falls out or temperature sensors fail in any way.
|
||||
*
|
||||
* The issue: If a thermistor falls out or a temperature sensor fails,
|
||||
* Marlin can no longer sense the actual temperature. Since a disconnected
|
||||
* thermistor reads as a low temperature, the firmware will keep the heater on.
|
||||
*
|
||||
* The solution: Once the temperature reaches the target, start observing.
|
||||
* If the temperature stays too far below the target (hysteresis) for too long (period),
|
||||
* the firmware will halt the machine as a safety precaution.
|
||||
*
|
||||
* If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
|
||||
|
||||
/**
|
||||
* Whenever an M104 or M109 increases the target temperature the firmware will wait for the
|
||||
* WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
|
||||
* degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
|
||||
* but only if the current temperature is far enough below the target for a reliable test.
|
||||
*
|
||||
* If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE
|
||||
* WATCH_TEMP_INCREASE should not be below 2.
|
||||
*/
|
||||
#define WATCH_TEMP_PERIOD 20 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Thermal Protection parameters for the bed are just as above for hotends.
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_BED)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
|
||||
/**
|
||||
* Whenever an M140 or M190 increases the target temperature the firmware will wait for the
|
||||
* WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE
|
||||
* degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190,
|
||||
* but only if the current temperature is far enough below the target for a reliable test.
|
||||
*
|
||||
* If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease
|
||||
* WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.)
|
||||
*/
|
||||
#define WATCH_BED_TEMP_PERIOD 60 // Seconds
|
||||
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
// this adds an experimental additional term to the heating power, proportional to the extrusion speed.
|
||||
// if Kc is chosen well, the additional required power due to increased melting should be compensated.
|
||||
#define PID_ADD_EXTRUSION_RATE
|
||||
#if ENABLED(PID_ADD_EXTRUSION_RATE)
|
||||
#define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
|
||||
#define LPQ_MAX_LEN 50
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Automatic Temperature:
|
||||
* The hotend target temperature is calculated by all the buffered lines of gcode.
|
||||
* The maximum buffered steps/sec of the extruder motor is called "se".
|
||||
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
|
||||
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
|
||||
* mintemp and maxtemp. Turn this off by executing M109 without F*
|
||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
*/
|
||||
#define AUTOTEMP
|
||||
#if ENABLED(AUTOTEMP)
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
#endif
|
||||
|
||||
//Show Temperature ADC value
|
||||
//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
|
||||
//#define SHOW_TEMP_ADC_VALUES
|
||||
|
||||
// @section extruder
|
||||
|
||||
// extruder run-out prevention.
|
||||
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
|
||||
//#define EXTRUDER_RUNOUT_PREVENT
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 190
|
||||
#define EXTRUDER_RUNOUT_SECONDS 30
|
||||
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
|
||||
#define EXTRUDER_RUNOUT_EXTRUDE 100
|
||||
|
||||
// @section temperature
|
||||
|
||||
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
|
||||
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
|
||||
#define TEMP_SENSOR_AD595_OFFSET 0.0
|
||||
#define TEMP_SENSOR_AD595_GAIN 1.0
|
||||
|
||||
//This is for controlling a fan to cool down the stepper drivers
|
||||
//it will turn on when any driver is enabled
|
||||
//and turn off after the set amount of seconds from last driver being disabled again
|
||||
#define CONTROLLERFAN_PIN 2 //Pin used for the fan to cool controller (-1 to disable)
|
||||
#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
|
||||
#define CONTROLLERFAN_SPEED 255 // == full speed
|
||||
|
||||
// When first starting the main fan, run it at full speed for the
|
||||
// given number of milliseconds. This gets the fan spinning reliably
|
||||
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
//#define FAN_KICKSTART_TIME 100
|
||||
|
||||
// This defines the minimal speed for the main fan, run in PWM mode
|
||||
// to enable uncomment and set minimal PWM speed for reliable running (1-255)
|
||||
// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
|
||||
//#define FAN_MIN_PWM 50
|
||||
|
||||
// @section extruder
|
||||
|
||||
// Extruder cooling fans
|
||||
// Configure fan pin outputs to automatically turn on/off when the associated
|
||||
// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
|
||||
// Multiple extruders can be assigned to the same pin in which case
|
||||
// the fan will turn on when any selected extruder is above the threshold.
|
||||
#define EXTRUDER_0_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_1_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_2_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_3_AUTO_FAN_PIN -1
|
||||
#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
|
||||
#define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//=============================Mechanical Settings===========================
|
||||
//===========================================================================
|
||||
|
||||
// @section homing
|
||||
|
||||
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
|
||||
|
||||
// @section extras
|
||||
|
||||
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
|
||||
|
||||
// A single Z stepper driver is usually used to drive 2 stepper motors.
|
||||
// Uncomment this define to utilize a separate stepper driver for each Z axis motor.
|
||||
// Only a few motherboards support this, like RAMPS, which have dual extruder support (the 2nd, often unused, extruder driver is used
|
||||
// to control the 2nd Z axis stepper motor). The pins are currently only defined for a RAMPS motherboards.
|
||||
// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
|
||||
//#define Z_DUAL_STEPPER_DRIVERS
|
||||
|
||||
#if ENABLED(Z_DUAL_STEPPER_DRIVERS)
|
||||
|
||||
// Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
|
||||
// That way the machine is capable to align the bed during home, since both Z steppers are homed.
|
||||
// There is also an implementation of M666 (software endstops adjustment) to this feature.
|
||||
// After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
|
||||
// One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
|
||||
// If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
|
||||
// Play a little bit with small adjustments (0.5mm) and check the behaviour.
|
||||
// The M119 (endstops report) will start reporting the Z2 Endstop as well.
|
||||
|
||||
//#define Z_DUAL_ENDSTOPS
|
||||
|
||||
#if ENABLED(Z_DUAL_ENDSTOPS)
|
||||
#define Z2_USE_ENDSTOP _XMAX_
|
||||
#endif
|
||||
|
||||
#endif // Z_DUAL_STEPPER_DRIVERS
|
||||
|
||||
// Same again but for Y Axis.
|
||||
//#define Y_DUAL_STEPPER_DRIVERS
|
||||
|
||||
#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
|
||||
// Define if the two Y drives need to rotate in opposite directions
|
||||
#define INVERT_Y2_VS_Y_DIR true
|
||||
#endif
|
||||
|
||||
// Enable this for dual x-carriage printers.
|
||||
// A dual x-carriage design has the advantage that the inactive extruder can be parked which
|
||||
// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
|
||||
// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
|
||||
//#define DUAL_X_CARRIAGE
|
||||
#if ENABLED(DUAL_X_CARRIAGE)
|
||||
// Configuration for second X-carriage
|
||||
// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
|
||||
// the second x-carriage always homes to the maximum endstop.
|
||||
#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
|
||||
#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed
|
||||
#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position
|
||||
#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
|
||||
// However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
|
||||
// override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
|
||||
// without modifying the firmware (through the "M218 T1 X???" command).
|
||||
// Remember: you should set the second extruder x-offset to 0 in your slicer.
|
||||
|
||||
// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
|
||||
// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
|
||||
// as long as it supports dual x-carriages. (M605 S0)
|
||||
// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
|
||||
// that additional slicer support is not required. (M605 S1)
|
||||
// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
|
||||
// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
|
||||
// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
|
||||
|
||||
// This is the default power-up mode which can be later using M605.
|
||||
#define DEFAULT_DUAL_X_CARRIAGE_MODE 0
|
||||
|
||||
// Default settings in "Auto-park Mode"
|
||||
#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder
|
||||
#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder
|
||||
|
||||
// Default x offset in duplication mode (typically set to half print bed width)
|
||||
#define DEFAULT_DUPLICATION_X_OFFSET 100
|
||||
|
||||
#endif //DUAL_X_CARRIAGE
|
||||
|
||||
// @section homing
|
||||
|
||||
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
#define X_HOME_BUMP_MM 10
|
||||
#define Y_HOME_BUMP_MM 10
|
||||
#define Z_HOME_BUMP_MM 3
|
||||
#define HOMING_BUMP_DIVISOR {2, 2, 4} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
// When G28 is called, this option will make Y home before X
|
||||
//#define HOME_Y_BEFORE_X
|
||||
|
||||
// @section machine
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
|
||||
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
|
||||
#define INVERT_X_STEP_PIN false
|
||||
#define INVERT_Y_STEP_PIN false
|
||||
#define INVERT_Z_STEP_PIN false
|
||||
#define INVERT_E_STEP_PIN false
|
||||
|
||||
// Default stepper release if idle. Set to 0 to deactivate.
|
||||
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
|
||||
// Time can be set by M18 and M84.
|
||||
#define DEFAULT_STEPPER_DEACTIVE_TIME 120
|
||||
#define DISABLE_INACTIVE_X true
|
||||
#define DISABLE_INACTIVE_Y true
|
||||
#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
|
||||
#define DISABLE_INACTIVE_E true
|
||||
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// @section lcd
|
||||
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
#define SLOWDOWN
|
||||
|
||||
// Frequency limit
|
||||
// See nophead's blog for more info
|
||||
// Not working O
|
||||
//#define XY_FREQUENCY_LIMIT 15
|
||||
|
||||
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
|
||||
// of the buffer and all stops. This should not be much greater than zero and should only be changed
|
||||
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
|
||||
#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
|
||||
|
||||
// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
|
||||
#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
|
||||
|
||||
// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
|
||||
#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
|
||||
|
||||
// Motor Current controlled via PWM (Overridable on supported boards with PWM-driven motor driver current)
|
||||
//#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps
|
||||
|
||||
// uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
|
||||
//#define DIGIPOT_I2C
|
||||
// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
|
||||
#define DIGIPOT_I2C_NUM_CHANNELS 8
|
||||
// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
|
||||
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
|
||||
|
||||
//===========================================================================
|
||||
//=============================Additional Features===========================
|
||||
//===========================================================================
|
||||
|
||||
#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
|
||||
#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
|
||||
#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
|
||||
|
||||
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
|
||||
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
|
||||
|
||||
// @section lcd
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
|
||||
#if ENABLED(SDSUPPORT)
|
||||
|
||||
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
|
||||
// around this by connecting a push button or single throw switch to the pin defined
|
||||
// as SD_DETECT_PIN in your board's pins definitions.
|
||||
// This setting should be disabled unless you are using a push button, pulling the pin to ground.
|
||||
// Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
|
||||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
|
||||
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
|
||||
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
|
||||
// using:
|
||||
//#define MENU_ADDAUTOSTART
|
||||
|
||||
// Show a progress bar on HD44780 LCDs for SD printing
|
||||
//#define LCD_PROGRESS_BAR
|
||||
|
||||
#if ENABLED(LCD_PROGRESS_BAR)
|
||||
// Amount of time (ms) to show the bar
|
||||
#define PROGRESS_BAR_BAR_TIME 2000
|
||||
// Amount of time (ms) to show the status message
|
||||
#define PROGRESS_BAR_MSG_TIME 3000
|
||||
// Amount of time (ms) to retain the status message (0=forever)
|
||||
#define PROGRESS_MSG_EXPIRE 0
|
||||
// Enable this to show messages for MSG_TIME then hide them
|
||||
//#define PROGRESS_MSG_ONCE
|
||||
#endif
|
||||
|
||||
// This allows hosts to request long names for files and folders with M33
|
||||
//#define LONG_FILENAME_HOST_SUPPORT
|
||||
|
||||
// This option allows you to abort SD printing when any endstop is triggered.
|
||||
// This feature must be enabled with "M540 S1" or from the LCD menu.
|
||||
// To have any effect, endstops must be enabled during SD printing.
|
||||
// With ENDSTOPS_ONLY_FOR_HOMING you must send "M120" to enable endstops.
|
||||
//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
||||
|
||||
#endif // SDSUPPORT
|
||||
|
||||
// for dogm lcd displays you can choose some additional fonts:
|
||||
#if ENABLED(DOGLCD)
|
||||
// save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
|
||||
// we don't have a big font for Cyrillic, Kana
|
||||
//#define USE_BIG_EDIT_FONT
|
||||
|
||||
// If you have spare 2300Byte of progmem and want to use a
|
||||
// smaller font on the Info-screen uncomment the next line.
|
||||
//#define USE_SMALL_INFOFONT
|
||||
#endif // DOGLCD
|
||||
|
||||
// @section safety
|
||||
|
||||
// The hardware watchdog should reset the microcontroller disabling all outputs,
|
||||
// in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
#define USE_WATCHDOG
|
||||
|
||||
#if ENABLED(USE_WATCHDOG)
|
||||
// If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
|
||||
// The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
|
||||
// However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
|
||||
//#define WATCHDOG_RESET_MANUAL
|
||||
#endif
|
||||
|
||||
// @section lcd
|
||||
|
||||
// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
|
||||
// it can e.g. be used to change z-positions in the print startup phase in real-time
|
||||
// does not respect endstops!
|
||||
//#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
|
||||
//not implemented for deltabots!
|
||||
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
|
||||
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
|
||||
#endif
|
||||
|
||||
// @section extruder
|
||||
|
||||
// extruder advance constant (s2/mm3)
|
||||
//
|
||||
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
|
||||
//
|
||||
// Hooke's law says: force = k * distance
|
||||
// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
// so: v ^ 2 is proportional to number of steps we advance the extruder
|
||||
//#define ADVANCE
|
||||
|
||||
#if ENABLED(ADVANCE)
|
||||
#define EXTRUDER_ADVANCE_K .0
|
||||
#define D_FILAMENT 2.85
|
||||
#endif
|
||||
|
||||
// Implementation of a linear pressure control
|
||||
// Assumption: advance = k * (delta velocity)
|
||||
// K=0 means advance disabled. A good value for a gregs wade extruder will be around K=75
|
||||
//#define LIN_ADVANCE
|
||||
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
#define LIN_ADVANCE_K 75
|
||||
#endif
|
||||
|
||||
// @section leveling
|
||||
|
||||
// Default mesh area is an area with an inset margin on the print area.
|
||||
// Below are the macros that are used to define the borders for the mesh area,
|
||||
// made available here for specialized needs, ie dual extruder setup.
|
||||
#if ENABLED(MESH_BED_LEVELING)
|
||||
#define MESH_MIN_X (X_MIN_POS + MESH_INSET)
|
||||
#define MESH_MAX_X (X_MAX_POS - (MESH_INSET))
|
||||
#define MESH_MIN_Y (Y_MIN_POS + MESH_INSET)
|
||||
#define MESH_MAX_Y (Y_MAX_POS - (MESH_INSET))
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
// Arc interpretation settings:
|
||||
#define ARC_SUPPORT // Disabling this saves ~2738 bytes
|
||||
#define MM_PER_ARC_SEGMENT 1
|
||||
#define N_ARC_CORRECTION 25
|
||||
|
||||
// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
|
||||
//#define BEZIER_CURVE_SUPPORT
|
||||
|
||||
const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
||||
// @section temperature
|
||||
|
||||
// Control heater 0 and heater 1 in parallel.
|
||||
//#define HEATERS_PARALLEL
|
||||
|
||||
//===========================================================================
|
||||
//================================= Buffers =================================
|
||||
//===========================================================================
|
||||
|
||||
// @section hidden
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
#if ENABLED(SDSUPPORT)
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
||||
// The ASCII buffer for serial input
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 26
|
||||
|
||||
// Bad Serial-connections can miss a received command by sending an 'ok'
|
||||
// Therefore some clients abort after 30 seconds in a timeout.
|
||||
// Some other clients start sending commands while receiving a 'wait'.
|
||||
// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
|
||||
//#define NO_TIMEOUTS 1000 // Milliseconds
|
||||
|
||||
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
//#define ADVANCED_OK
|
||||
|
||||
// @section fwretract
|
||||
|
||||
// Firmware based and LCD controlled retract
|
||||
// M207 and M208 can be used to define parameters for the retraction.
|
||||
// The retraction can be called by the slicer using G10 and G11
|
||||
// until then, intended retractions can be detected by moves that only extrude and the direction.
|
||||
// the moves are than replaced by the firmware controlled ones.
|
||||
|
||||
//#define FWRETRACT //ONLY PARTIALLY TESTED
|
||||
#if ENABLED(FWRETRACT)
|
||||
#define MIN_RETRACT 0.1 //minimum extruded mm to accept a automatic gcode retraction attempt
|
||||
#define RETRACT_LENGTH 3 //default retract length (positive mm)
|
||||
#define RETRACT_LENGTH_SWAP 13 //default swap retract length (positive mm), for extruder change
|
||||
#define RETRACT_FEEDRATE 45 //default feedrate for retracting (mm/s)
|
||||
#define RETRACT_ZLIFT 0 //default retract Z-lift
|
||||
#define RETRACT_RECOVER_LENGTH 0 //default additional recover length (mm, added to retract length when recovering)
|
||||
#define RETRACT_RECOVER_LENGTH_SWAP 0 //default additional swap recover length (mm, added to retract length when recovering from extruder change)
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s)
|
||||
#endif
|
||||
|
||||
// Add support for experimental filament exchange support M600; requires display
|
||||
#if ENABLED(ULTIPANEL)
|
||||
#define FILAMENT_CHANGE_FEATURE // Enable filament exchange menu and M600 g-code (used for runout sensor too)
|
||||
#if ENABLED(FILAMENT_CHANGE_FEATURE)
|
||||
#define FILAMENT_CHANGE_X_POS 100 // X position of hotend
|
||||
#define FILAMENT_CHANGE_Y_POS 100 // Y position of hotend
|
||||
#define FILAMENT_CHANGE_Z_ADD 20 // Z addition of hotend (lift)
|
||||
#define FILAMENT_CHANGE_XY_FEEDRATE 100 // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
|
||||
#define FILAMENT_CHANGE_Z_FEEDRATE 5 // Z axis feedrate in mm/s (not used for delta printers)
|
||||
#define FILAMENT_CHANGE_RETRACT_LENGTH 5 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter lenght for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 600 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 10 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_EXTRUDE_LENGTH 100 // Extrude filament length in mm after filament is load over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
* enable this section if you have TMC26X motor drivers.
|
||||
* you need to import the TMC26XStepper library into the Arduino IDE for this
|
||||
******************************************************************************/
|
||||
|
||||
// @section tmc
|
||||
|
||||
//#define HAVE_TMCDRIVER
|
||||
#if ENABLED(HAVE_TMCDRIVER)
|
||||
|
||||
//#define X_IS_TMC
|
||||
#define X_MAX_CURRENT 1000 //in mA
|
||||
#define X_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define X2_IS_TMC
|
||||
#define X2_MAX_CURRENT 1000 //in mA
|
||||
#define X2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define Y_IS_TMC
|
||||
#define Y_MAX_CURRENT 1000 //in mA
|
||||
#define Y_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define Y2_IS_TMC
|
||||
#define Y2_MAX_CURRENT 1000 //in mA
|
||||
#define Y2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define Z_IS_TMC
|
||||
#define Z_MAX_CURRENT 1000 //in mA
|
||||
#define Z_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define Z2_IS_TMC
|
||||
#define Z2_MAX_CURRENT 1000 //in mA
|
||||
#define Z2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define E0_IS_TMC
|
||||
#define E0_MAX_CURRENT 1000 //in mA
|
||||
#define E0_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define E1_IS_TMC
|
||||
#define E1_MAX_CURRENT 1000 //in mA
|
||||
#define E1_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define E2_IS_TMC
|
||||
#define E2_MAX_CURRENT 1000 //in mA
|
||||
#define E2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
//#define E3_IS_TMC
|
||||
#define E3_MAX_CURRENT 1000 //in mA
|
||||
#define E3_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
#endif
|
||||
|
||||
/******************************************************************************\
|
||||
* enable this section if you have L6470 motor drivers.
|
||||
* you need to import the L6470 library into the Arduino IDE for this
|
||||
******************************************************************************/
|
||||
|
||||
// @section l6470
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#if ENABLED(HAVE_L6470DRIVER)
|
||||
|
||||
//#define X_IS_L6470
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
#define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define X2_IS_L6470
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
#define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define Y_IS_L6470
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
#define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define Y2_IS_L6470
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
#define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define Z_IS_L6470
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
#define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define Z2_IS_L6470
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
#define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define E0_IS_L6470
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
#define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define E1_IS_L6470
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
#define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define E2_IS_L6470
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
#define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
//#define E3_IS_L6470
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
#define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be careful not to go too high
|
||||
#define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
#endif
|
||||
|
||||
/**
|
||||
* TWI/I2C BUS
|
||||
*
|
||||
* This feature is an EXPERIMENTAL feature so it shall not be used on production
|
||||
* machines. Enabling this will allow you to send and receive I2C data from slave
|
||||
* devices on the bus.
|
||||
*
|
||||
* ; Example #1
|
||||
* ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
|
||||
* ; It uses multiple M155 commands with one B<base 10> arg
|
||||
* M155 A99 ; Target slave address
|
||||
* M155 B77 ; M
|
||||
* M155 B97 ; a
|
||||
* M155 B114 ; r
|
||||
* M155 B108 ; l
|
||||
* M155 B105 ; i
|
||||
* M155 B110 ; n
|
||||
* M155 S1 ; Send the current buffer
|
||||
*
|
||||
* ; Example #2
|
||||
* ; Request 6 bytes from slave device with address 0x63 (99)
|
||||
* M156 A99 B5
|
||||
*
|
||||
* ; Example #3
|
||||
* ; Example serial output of a M156 request
|
||||
* echo:i2c-reply: from:99 bytes:5 data:hello
|
||||
*/
|
||||
|
||||
// @section i2cbus
|
||||
|
||||
//#define EXPERIMENTAL_I2CBUS
|
||||
|
||||
#include "Conditionals.h"
|
||||
#include "SanityCheck.h"
|
||||
|
||||
#endif //CONFIGURATION_ADV_H
|
||||
1216
Marlin/example_configurations/K8400/Dual Heads/Configuration.h
Normal file
1216
Marlin/example_configurations/K8400/Dual Heads/Configuration.h
Normal file
File diff suppressed because it is too large
Load Diff
15
Marlin/example_configurations/K8400/README.md
Normal file
15
Marlin/example_configurations/K8400/README.md
Normal file
@ -0,0 +1,15 @@
|
||||
# Configuration for Velleman K8400 Vertex
|
||||
http://www.k8400.eu/
|
||||
|
||||
Configuration files for the K8400, ported upstream from the official Velleman firmware.
|
||||
Like it's predecessor, (K8200), the K8400 is a 3Drag clone. There are some minor differences, documented in pins_K8400.h.
|
||||
|
||||
Single and dual head configurations provided. Copy the correct Configuration.h and Configuration_adv.h to the /Marlin/ directory.
|
||||
|
||||
**NOTE: This configuration includes the community sourced feed rate fix. Use 100% feed rate in Repetier!**
|
||||
|
||||
For implementation and updated K8400 firmware, see https://github.com/birkett/Velleman-K8400-Firmware
|
||||
|
||||
### Original Sources
|
||||
Credit to Velleman for the original 1.0.x based code:<br />
|
||||
http://www.vertex3dprinter.eu/downloads/files/vertex/firmware/vertex-m1-v1.4-h2.zip
|
||||
@ -77,6 +77,8 @@
|
||||
#include "pins_3DRAG.h"
|
||||
#elif MB(K8200)
|
||||
#include "pins_K8200.h"
|
||||
#elif MB(K8400)
|
||||
#include "pins_K8400.h"
|
||||
#elif MB(TEENSYLU)
|
||||
#include "pins_TEENSYLU.h"
|
||||
#elif MB(RUMBA)
|
||||
|
||||
@ -21,7 +21,7 @@
|
||||
*/
|
||||
|
||||
/**
|
||||
* 3DRAG (and K8200) Arduino Mega with RAMPS v1.4 pin assignments
|
||||
* 3DRAG (and K8200 / K8400) Arduino Mega with RAMPS v1.4 pin assignments
|
||||
*/
|
||||
|
||||
#ifndef BOARD_NAME
|
||||
|
||||
52
Marlin/pins_K8400.h
Normal file
52
Marlin/pins_K8400.h
Normal file
@ -0,0 +1,52 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Velleman K8400 (Vertex)
|
||||
* 3DRAG clone
|
||||
*
|
||||
* K8400 has some minor differences over a normal 3Drag:
|
||||
* - No X/Y max endstops
|
||||
* - Second extruder step pin has moved
|
||||
* - No power supply control
|
||||
* - Second heater has moved pin
|
||||
*/
|
||||
|
||||
#define BOARD_NAME "K8400"
|
||||
#define DEFAULT_MACHINE_NAME "Vertex"
|
||||
#define DEFAULT_SOURCE_CODE_URL "https://github.com/birkett/Vertex-K8400-Firmware"
|
||||
|
||||
#include "pins_3DRAG.h"
|
||||
|
||||
#undef X_MAX_PIN
|
||||
#define X_MAX_PIN -1
|
||||
#undef Y_MAX_PIN
|
||||
#define Y_MAX_PIN -1
|
||||
|
||||
#undef E1_STEP_PIN
|
||||
#define E1_STEP_PIN 32
|
||||
|
||||
#undef PS_ON_PIN
|
||||
#undef KILL_PIN
|
||||
|
||||
#undef HEATER_1_PIN
|
||||
#define HEATER_1_PIN 11
|
||||
@ -59,7 +59,7 @@
|
||||
#define CPU_ST7920_DELAY_1 DELAY_0_NOP
|
||||
#define CPU_ST7920_DELAY_2 DELAY_0_NOP
|
||||
#define CPU_ST7920_DELAY_3 DELAY_1_NOP
|
||||
#elif (MOTHERBOARD == BOARD_3DRAG) || (MOTHERBOARD == BOARD_K8200)
|
||||
#elif (MOTHERBOARD == BOARD_3DRAG) || (MOTHERBOARD == BOARD_K8200) || (MOTHERBOARD == BOARD_K8400)
|
||||
#define CPU_ST7920_DELAY_1 DELAY_0_NOP
|
||||
#define CPU_ST7920_DELAY_2 DELAY_3_NOP
|
||||
#define CPU_ST7920_DELAY_3 DELAY_0_NOP
|
||||
|
||||
Loading…
Reference in New Issue
Block a user