diff --git a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
index 5a577ddcd5..9d35494d90 100644
--- a/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/Marlin/src/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -595,42 +595,42 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS DELTA_PRINTABLE_RADIUS - MIN_PROBE_EDGE // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
#if ENABLED(ANYCUBIC_KOSSEL_PLUS)
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 116.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 116.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 267 // (mm)
+ #define DELTA_DIAGONAL_ROD 267 // (mm)
// Horizontal offset from middle of printer to smooth rod center.
- #define DELTA_SMOOTH_ROD_OFFSET 186 // (mm)
+ #define DELTA_SMOOTH_ROD_OFFSET 186 // (mm)
// Horizontal offset of the universal joints on the end effector.
- #define DELTA_EFFECTOR_OFFSET 31 // (mm)
+ #define DELTA_EFFECTOR_OFFSET 31 // (mm)
// Horizontal offset of the universal joints on the carriages.
- #define DELTA_CARRIAGE_OFFSET 20.6 // (mm)
+ #define DELTA_CARRIAGE_OFFSET 20.6 // (mm)
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) //mm Get this value from auto calibrate
+ #define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-(DELTA_EFFECTOR_OFFSET)-(DELTA_CARRIAGE_OFFSET)) // (mm) Get this value from G33 auto calibrate
#else
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 90.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 90.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 218.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 218.0 // (mm)
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 97.0 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 97.0 // (mm) Get this value from G33 auto calibrate
#endif
- // height from z=0 to home position
- #define DELTA_HEIGHT 320.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 320.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index f7ae89e47a..b70ba4299e 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -562,29 +562,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 73.5 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 85.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 85.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 218.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 218.0 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 295.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 295.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 101.0 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 101.0 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
index d29c31148a..db4e219a7e 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -560,31 +560,31 @@
#if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
- #define DELTA_CALIBRATION_RADIUS 63 // (mm)
+ #define DELTA_CALIBRATION_RADIUS 63 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 70.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 70.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 218.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 218.0 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 317.94 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 317.94 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 110.0 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 110.0 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index 6801592a35..c136c7d98f 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -562,29 +562,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 73.5 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 85.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 85.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 218.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 218.0 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 280.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 280.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 101.0 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 101.0 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h
index 42d6e991c9..ec108165f0 100644
--- a/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h
+++ b/Marlin/src/config/examples/delta/Geeetech/Rostock 301/Configuration.h
@@ -563,29 +563,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 121.5 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 90.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 90.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 196.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 196.0 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 228.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 228.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 92 //124.0 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 92 //124.0 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 996bb58b08..8fbd95c38f 100644
--- a/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/Marlin/src/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -567,29 +567,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 121.5 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 151.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 151.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 356.5 // (mm)
+ #define DELTA_DIAGONAL_ROD 356.5 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 352.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 352.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 176.5 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 176.5 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h b/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h
index c66e9f744c..b0fac96f39 100644
--- a/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h
+++ b/Marlin/src/config/examples/delta/MKS/SBASE/Configuration.h
@@ -552,29 +552,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 121.5 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 250.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 250.0 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 250.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 250.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 124.0 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 124.0 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h b/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h
index c65ededaa5..d700ada3e2 100644
--- a/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h
+++ b/Marlin/src/config/examples/delta/Tevo Little Monster/Configuration.h
@@ -554,31 +554,31 @@
#if ENABLED(DELTA_AUTO_CALIBRATION) || ENABLED(DELTA_CALIBRATION_MENU)
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
- #define DELTA_CALIBRATION_RADIUS 140 // (mm)
+ #define DELTA_CALIBRATION_RADIUS 140 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 165.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 165.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 397.19 // (mm)
+ #define DELTA_DIAGONAL_ROD 397.19 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 522.27 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 522.27 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, -0.12, -0.78 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, -0.12, -0.78 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 157.39 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 157.39 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { -0.18, 0.18, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { -0.18, 0.18, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h
index 29bb6f54f3..d96552791c 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration.h
@@ -552,29 +552,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 121.5 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 250.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 250.0 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 250.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 250.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 124.0 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 124.0 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
index 8185306dc5..2b49114c73 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h
@@ -552,29 +552,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 78.0 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 90.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 90.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 215.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 215.0 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 250.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 250.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 105.2 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 105.2 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
index 33f43cbeca..be8534b915 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h
@@ -538,29 +538,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 110.0 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 127.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 127.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 301.0 // (mm)
+ #define DELTA_DIAGONAL_ROD 301.0 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 277.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 277.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 152.357 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 152.357 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
index f5aa6b5935..518553b5a1 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h
@@ -556,29 +556,29 @@
// Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes
#define DELTA_CALIBRATION_RADIUS 121.5 // (mm)
// Set the steprate for papertest probing
- #define PROBE_MANUALLY_STEP 0.05 // (mm)
+ #define PROBE_MANUALLY_STEP 0.05 // (mm)
#endif
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
- #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
+ #define DELTA_PRINTABLE_RADIUS 140.0 // (mm)
// Center-to-center distance of the holes in the diagonal push rods.
- #define DELTA_DIAGONAL_ROD 319.5 // (mm)
+ #define DELTA_DIAGONAL_ROD 319.5 // (mm)
- // height from z=0 to home position
- #define DELTA_HEIGHT 380.00 // get this value from auto calibrate
+ // Distance between bed and nozzle Z home position
+ #define DELTA_HEIGHT 380.00 // (mm) Get this value from G33 auto calibrate
- #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // get these from auto calibrate
+ #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
// Horizontal distance bridged by diagonal push rods when effector is centered.
- #define DELTA_RADIUS 174.1 //mm Get this value from auto calibrate
+ #define DELTA_RADIUS 174.1 // (mm) Get this value from G33 auto calibrate
// Trim adjustments for individual towers
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
// measured in degrees anticlockwise looking from above the printer
- #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // get these values from auto calibrate
+ #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
- // delta radius and diaginal rod adjustments measured in mm
+ // Delta radius and diagonal rod adjustments (mm)
//#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
diff --git a/buildroot/share/fonts/README.md b/buildroot/share/fonts/README.md
index ee9d8e00bb..4e6f6f9b15 100644
--- a/buildroot/share/fonts/README.md
+++ b/buildroot/share/fonts/README.md
@@ -16,7 +16,7 @@ http://creativecommons.org/publicdomain/zero/1.0/
- ISO10646_Kana.fon ([fe2bd23](https://github.com/MarlinFirmware/Marlin/commit/fe2bd237d556439499dfdee852c1550c7a16430a))
- Marlin_symbols.fon ([fe2bd23](https://github.com/MarlinFirmware/Marlin/commit/fe2bd237d556439499dfdee852c1550c7a16430a))
-Additional changes to the original font files being distritubted with Marlin are copyrighted under the terms of the [GPLv3](http://www.gnu.org/licenses/gpl-3.0.txt) license.
+Additional changes to the original font files distributed with Marlin are copyrighted under the terms of the [GPLv3](http://www.gnu.org/licenses/gpl-3.0.txt) license.
## Documentation