Merge branch 'bugfix-2.0.x' of https://github.com/MarlinFirmware/Marlin into bugfix-2.0.x

Marlin/Configuration_adv.h

@@ -50,6 +50,19 @@
   #define HEATER_BED_INVERTING true
 #endif
 
+/**
+ * Heated Chamber settings
+ */
+#if TEMP_SENSOR_CHAMBER
+  #define CHAMBER_MINTEMP             5
+  #define CHAMBER_MAXTEMP            60
+  #define TEMP_CHAMBER_HYSTERESIS     1   // (°C) Temperature proximity considered "close enough" to the target
+  #define THERMAL_PROTECTION_CHAMBER      // Enable thermal protection for the heated chamber
+  //#define CHAMBER_LIMIT_SWITCHING
+  //#define HEATER_CHAMBER_PIN       44   // Chamber heater on/off pin
+  //#define HEATER_CHAMBER_INVERTING false
+#endif
+
 #if DISABLED(PIDTEMPBED)
   #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control
   #if ENABLED(BED_LIMIT_SWITCHING)
@@ -127,8 +140,8 @@
 #endif
 
 #if ENABLED(PIDTEMP)
-  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
-  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+  // Add an experimental additional term to the heater power, proportional to the extrusion speed.
+  // A well-chosen Kc value should add just enough power to melt the increased material volume.
   //#define PID_EXTRUSION_SCALING
   #if ENABLED(PID_EXTRUSION_SCALING)
     #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
@@ -456,6 +469,7 @@
 #define Z_HOME_BUMP_MM 2
 #define HOMING_BUMP_DIVISOR { 2, 2, 4 }  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
 //#define QUICK_HOME                     // If homing includes X and Y, do a diagonal move initially
+//#define HOMING_BACKOFF_MM { 2, 2, 2 }  // (mm) Move away from the endstops after homing
 
 // When G28 is called, this option will make Y home before X
 //#define HOME_Y_BEFORE_X
@@ -678,6 +692,7 @@
    *                        A   (A shifted)   B   (B shifted)  IC
    * Smoothie              0x2C (0x58)       0x2D (0x5A)       MCP4451
    * AZTEEG_X3_PRO         0x2C (0x58)       0x2E (0x5C)       MCP4451
+   * AZTEEG_X5_MINI        0x2C (0x58)       0x2E (0x5C)       MCP4451
    * AZTEEG_X5_MINI_WIFI         0x58              0x5C        MCP4451
    * MIGHTYBOARD_REVE      0x2F (0x5E)                         MCP4018
    */
@@ -770,8 +785,11 @@
   // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
   #define SDCARD_RATHERRECENTFIRST
 
-  // Add an option in the menu to run all auto#.g files
-  //#define MENU_ADDAUTOSTART
+  #define SD_MENU_CONFIRM_START             // Confirm the selected SD file before printing
+
+  //#define MENU_ADDAUTOSTART               // Add a menu option to run auto#.g files
+
+  #define EVENT_GCODE_SD_STOP "G28XY"       // G-code to run on Stop Print (e.g., "G28XY" or "G27")
 
   /**
    * Continue after Power-Loss (Creality3D)
@@ -959,6 +977,12 @@
   //#define STATUS_ALT_FAN_BITMAP     // Use the alternative fan bitmap
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
   //#define STATUS_HEAT_PERCENT       // Show heating in a progress bar
+  //#define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
+
+  // Frivolous Game Options
+  //#define MARLIN_BRICKOUT
+  //#define MARLIN_INVADERS
+  //#define MARLIN_SNAKE
 
   // Frivolous Game Options
   //#define MARLIN_BRICKOUT
@@ -1000,13 +1024,15 @@
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
-    //#define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
+    #define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
     //#define MOVE_Z_WHEN_IDLE              // Jump to the move Z menu on doubleclick when printer is idle.
     #if ENABLED(MOVE_Z_WHEN_IDLE)
       #define MOVE_Z_IDLE_MULTIPLICATOR 1   // Multiply 1mm by this factor for the move step size.
     #endif
   #endif
 
+  //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
+
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets