diff --git a/Marlin/src/HAL/STM32F1/onboard_sd.cpp b/Marlin/src/HAL/STM32F1/onboard_sd.cpp index e26947145d..df98c2c057 100644 --- a/Marlin/src/HAL/STM32F1/onboard_sd.cpp +++ b/Marlin/src/HAL/STM32F1/onboard_sd.cpp @@ -158,7 +158,7 @@ static void sd_power_on() { ONBOARD_SD_SPI.begin(); ONBOARD_SD_SPI.setBitOrder(MSBFIRST); ONBOARD_SD_SPI.setDataMode(SPI_MODE0); - OUT_WRITE(ONBOARD_SD_CS_PIN, HIGH); // Set CS# high + CS_HIGH(); } // Disable SPI function diff --git a/Marlin/src/pins/lpc1768/pins_AZSMZ_MINI.h b/Marlin/src/pins/lpc1768/pins_AZSMZ_MINI.h index 5131069f6b..9211a6a793 100644 --- a/Marlin/src/pins/lpc1768/pins_AZSMZ_MINI.h +++ b/Marlin/src/pins/lpc1768/pins_AZSMZ_MINI.h @@ -85,7 +85,6 @@ #define FAN1_PIN P0_26 #define LCD_SDSS P0_16 // LCD SD chip select -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #if ENABLED(AZSMZ_12864) #define BEEPER_PIN P1_30 @@ -109,6 +108,7 @@ #define SD_SCK_PIN P0_07 #define SD_MISO_PIN P0_08 #define SD_MOSI_PIN P0_09 + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #define SD_SS_PIN ONBOARD_SD_CS_PIN #elif SD_CONNECTION_IS(CUSTOM_CABLE) #error "No custom SD drive cable defined for this board." diff --git a/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_1.h b/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_1.h index c6a44123a0..c01afccaca 100644 --- a/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_1.h +++ b/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_1.h @@ -54,7 +54,7 @@ /** - * ______ ______ + * ------ ------ * NC | 1 2 | GND 5V | 1 2 | GND * RESET | 3 4 | 1.31 NC | 3 4 | NC * 0.18 | 5 6 3.25 NC | 5 6 0.15 @@ -82,7 +82,6 @@ #define EXP2_09_PIN P0_15 #define EXP2_10_PIN P0_17 - /** * LCD / Controller * diff --git a/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h b/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h index b922f057f1..1ce6aed700 100644 --- a/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h +++ b/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h @@ -184,7 +184,7 @@ #endif /** - * ______ ______ + * ------ ------ * NC | 1 2 | GND 5V | 1 2 | GND * RESET | 3 4 | 1.31 (SD_DETECT) (LCD_D7) 1.23 | 3 4 | 1.22 (LCD_D6) * (MOSI) 0.18 | 5 6 3.25 (BTN_EN2) (LCD_D5) 1.21 | 5 6 1.20 (LCD_D4) @@ -230,7 +230,7 @@ * The ANET_FULL_GRAPHICS_LCD connector plug: * * BEFORE AFTER - * ______ ______ + * ------ ------ * GND 1 | 1 2 | 2 5V 5V 1 | 1 2 | 2 GND * CS 3 | 3 4 | 4 BTN_EN2 CS 3 | 3 4 | 4 BTN_EN2 * SID 5 | 5 6 6 BTN_EN1 SID 5 | 5 6 6 BTN_EN1 @@ -386,11 +386,11 @@ /** * Creality Ender-2 display pinout - * _____ + * ----- * 5V | 1 2 | GND * (MOSI) P1_23 | 3 4 | P1_22 (LCD_CS) * (LCD_A0) P1_21 | 5 6 P1_20 (BTN_EN2) - * RESET P1_19 | 7 8 | P1_18 (BTN_EN1) + * (RESET) P1_19 | 7 8 | P1_18 (BTN_EN1) * (BTN_ENC) P0_28 | 9 10| P1_30 (SCK) * ----- * EXP1 diff --git a/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h b/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h index 2c9e608e49..ae6456a3ce 100644 --- a/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h +++ b/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h @@ -239,14 +239,14 @@ #define TMC_BAUD_RATE 19200 #endif -/* _____ _____ - * NC | 1 2 | GND 5V | 1 2 | GND - * RESET | 3 4 | 1.31 1.23 | 3 4 | 1.22 - * 0.18 | 5 6 3.25 1.21 | 5 6 1.20 - * 0.16 | 7 8 | 3.26 1.19 | 7 8 | 1.18 - * 0.15 | 9 10| 0.17 0.28 | 9 10| 1.30 - * ----- ----- - * EXP2 EXP1 +/** ------ ------ + * NC | 1 2 | GND 5V | 1 2 | GND + * RESET | 3 4 | 1.31 1.23 | 3 4 | 1.22 + * 0.18 | 5 6 3.25 1.21 | 5 6 1.20 + * 0.16 | 7 8 | 3.26 1.19 | 7 8 | 1.18 + * 0.15 | 9 10| 0.17 0.28 | 9 10| 1.30 + * ------ ------ + * EXP2 EXP1 */ #define EXP1_03_PIN P1_23 @@ -267,27 +267,15 @@ #define EXP2_09_PIN P0_15 #define EXP2_10_PIN P0_17 -/** - * _____ _____ - * NC | · · | GND 5V | · · | GND - * RESET | · · | 1.31 (SD_DETECT) (LCD_D7) 1.23 | · · | 1.22 (LCD_D6) - * (MOSI) 0.18 | · · 3.25 (BTN_EN2) (LCD_D5) 1.21 | · · 1.20 (LCD_D4) - * (SD_SS) 0.16 | · · | 3.26 (BTN_EN1) (LCD_RS) 1.19 | · · | 1.18 (LCD_EN) - * (SCK) 0.15 | · · | 0.17 (MISO) (BTN_ENC) 0.28 | · · | 1.30 (BEEPER) - * ----- ----- - * EXP2 EXP1 - */ - -#if ENABLED(DWIN_CREALITY_LCD) +#if EITHER(DWIN_CREALITY_LCD, IS_DWIN_MARLINUI) // RET6 DWIN ENCODER LCD - #define BTN_ENC P1_20 - #define BTN_EN1 P1_23 - #define BTN_EN2 P1_22 + #define BTN_ENC EXP1_06_PIN + #define BTN_EN1 EXP1_03_PIN + #define BTN_EN2 EXP1_04_PIN #ifndef BEEPER_PIN - #define BEEPER_PIN P1_21 - #undef SPEAKER + #define BEEPER_PIN EXP1_05_PIN #endif #elif HAS_WIRED_LCD && !BTT_MOTOR_EXPANSION @@ -304,13 +292,13 @@ * The ANET_FULL_GRAPHICS_LCD_ALT_WIRING connector plug: * * BEFORE AFTER - * _____ _____ - * GND | 1 2 | 5V 5V | 1 2 | GND - * CS | 3 4 | BTN_EN2 CS | 3 4 | BTN_EN2 - * SID | 5 6 BTN_EN1 SID | 5 6 BTN_EN1 - * open | 7 8 | BTN_ENC open | 7 8 | BTN_ENC - * CLK | 9 10| Beeper CLK | 9 10| Beeper - * ----- ----- + * ------ ------ + * GND | 1 2 | 5V 5V | 1 2 | GND + * CS | 3 4 | BTN_EN2 CS | 3 4 | BTN_EN2 + * SID | 5 6 BTN_EN1 SID | 5 6 BTN_EN1 + * open | 7 8 | BTN_ENC open | 7 8 | BTN_ENC + * CLK | 9 10| BEEPER CLK | 9 10| BEEPER + * ------ ------ * LCD LCD */ @@ -337,15 +325,15 @@ * * The ANET_FULL_GRAPHICS_LCD connector plug: * - * BEFORE AFTER - * ______ ______ - * GND | 1 2 | 5V 5V | 1 2 | GND - * CS | 3 4 | BTN_EN2 CS | 3 4 | BTN_EN2 - * SID | 5 6 BTN_EN1 SID | 5 6 BTN_EN1 - * open | 7 8 | BTN_ENC CLK | 7 8 | BTN_ENC - * CLK | 9 10 | Beeper open | 9 10 | Beeper - * ------ ------ - * LCD LCD + * BEFORE AFTER + * ------ ------ + * GND | 1 2 | 5V 5V | 1 2 | GND + * CS | 3 4 | BTN_EN2 CS | 3 4 | BTN_EN2 + * SID | 5 6 BTN_EN1 SID | 5 6 BTN_EN1 + * open | 7 8 | BTN_ENC CLK | 7 8 | BTN_ENC + * CLK | 9 10 | BEEPER open | 9 10 | BEEPER + * ------ ------ + * LCD LCD */ #define LCD_PINS_RS EXP1_03_PIN @@ -372,7 +360,7 @@ #elif ENABLED(ENDER2_STOCKDISPLAY) /** Creality Ender-2 display pinout - * ______ + * ------ * 5V | 1 2 | GND * (MOSI) 1.23 | 3 4 | 1.22 (LCD_RS) * (LCD_A0) 1.21 | 5 6 1.20 (BTN_EN2) diff --git a/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h b/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h index 9e04fc0479..52f34ed0f0 100644 --- a/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h +++ b/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h @@ -126,8 +126,6 @@ #endif #endif -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card - #if SD_CONNECTION_IS(LCD) && ENABLED(SKR_USE_LCD_SD_CARD_PINS_FOR_CS) #error "SDCARD_CONNECTION must not be 'LCD' with SKR_USE_LCD_SD_CARD_PINS_FOR_CS." #endif @@ -145,13 +143,14 @@ #define SD_SCK_PIN P0_07 #define SD_MISO_PIN P0_08 #define SD_MOSI_PIN P0_09 + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #define SD_SS_PIN ONBOARD_SD_CS_PIN #elif SD_CONNECTION_IS(CUSTOM_CABLE) #error "No custom SD drive cable defined for this board." #endif #if ENABLED(BTT_MOTOR_EXPANSION) - /** ______ ______ + /** ------ ------ * NC | 1 2 | GND NC | 1 2 | GND * NC | 3 4 | M1EN M2EN | 3 4 | M3EN * M1STP | 5 6 M1DIR M1RX | 5 6 M1DIAG diff --git a/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h b/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h index 1feaeb13b5..eee3ede713 100644 --- a/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h +++ b/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h @@ -155,8 +155,6 @@ #define SDCARD_CONNECTION LCD #endif -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card - #if SD_CONNECTION_IS(LCD) #define SD_SCK_PIN P0_15 #define SD_MISO_PIN P0_17 @@ -167,5 +165,6 @@ #define SD_SCK_PIN P0_07 #define SD_MISO_PIN P0_08 #define SD_MOSI_PIN P0_09 + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #define SD_SS_PIN ONBOARD_SD_CS_PIN #endif diff --git a/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h b/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h index a2235dc28a..d1d1eccc45 100644 --- a/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h +++ b/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h @@ -165,8 +165,6 @@ #define SDCARD_CONNECTION ONBOARD #endif -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card - #if SD_CONNECTION_IS(CUSTOM_CABLE) /** @@ -199,6 +197,7 @@ #define SD_SS_PIN P0_28 #else #define SD_DETECT_PIN P0_27 + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #define SD_SS_PIN ONBOARD_SD_CS_PIN #endif #endif diff --git a/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h b/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h index 449d9a93ce..49dad8b07b 100644 --- a/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h +++ b/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h @@ -215,7 +215,7 @@ // Power Supply Control // #if ENABLED(MKS_PWC) - #define PS_ON_PIN P2_00 // SERVO + #define PS_ON_PIN P2_00 // SERVO1 #define KILL_PIN P1_24 // Z+ #define KILL_PIN_STATE HIGH #endif @@ -228,42 +228,79 @@ #define LED3_PIN P1_20 #define LED4_PIN P1_21 -/** - * _____ _____ - * (BEEPER) 1.31 | · · | 1.30 (BTN_ENC) (MISO) 0.8 | · · | 0.7 (SD_SCK) - * (LCD_EN) 0.18 | · · | 0.16 (LCD_RS) (BTN_EN1) 3.25 | · · | 0.28 (SD_CS2) - * (LCD_D4) 0.15 | · · 0.17 (LCD_D5) (BTN_EN2) 3.26 | · · 0.9 (SD_MOSI) - * (LCD_D6) 1.0 | · · | 1.22 (LCD_D7) (SD_DETECT) 0.27 | · · | RST - * GND | · · | 5V GND | · · | NC - * ----- ----- - * EXP1 EXP2 +/** ------ ------ + * (BEEPER) 1.31 |10 9 | 1.30 (BTN_ENC) (MISO) 0.8 |10 9 | 0.7 (SD_SCK) + * (LCD_EN) 0.18 | 8 7 | 0.16 (LCD_RS) (BTN_EN1) 3.25 | 8 7 | 0.28 (SD_CS2) + * (LCD_D4) 0.15 | 6 5 0.17 (LCD_D5) (BTN_EN2) 3.26 | 6 5 0.9 (SD_MOSI) + * (LCD_D6) 1.0 | 4 3 | 1.22 (LCD_D7) (SD_DETECT) 0.27 | 4 3 | RESET + * GND | 2 1 | 5V GND | 2 1 | NC + * ------ ------ + * EXP1 EXP2 */ + +#define EXP1_03_PIN P1_22 +#define EXP1_04_PIN P1_00 +#define EXP1_05_PIN P0_17 +#define EXP1_06_PIN P0_15 +#define EXP1_07_PIN P0_16 +#define EXP1_08_PIN P0_18 +#define EXP1_09_PIN P1_30 +#define EXP1_10_PIN P1_31 + +#define EXP2_03_PIN -1 // RESET +#define EXP2_04_PIN P0_27 +#define EXP2_05_PIN P0_09 +#define EXP2_06_PIN P3_26 +#define EXP2_07_PIN P0_28 +#define EXP2_08_PIN P3_25 +#define EXP2_09_PIN P0_07 +#define EXP2_10_PIN P0_08 + +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +#if SD_CONNECTION_IS(LCD) || SD_CONNECTION_IS(ONBOARD) + #define SD_DETECT_PIN EXP2_04_PIN + #define SD_SCK_PIN EXP2_09_PIN + #define SD_MISO_PIN EXP2_10_PIN + #define SD_MOSI_PIN EXP2_05_PIN + #if SD_CONNECTION_IS(ONBOARD) + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card + #define SD_SS_PIN ONBOARD_SD_CS_PIN + #else + #define SD_SS_PIN EXP2_07_PIN + #endif +#elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif + #if HAS_WIRED_LCD - #define BEEPER_PIN P1_31 - #define BTN_ENC P1_30 + #define BEEPER_PIN EXP1_10_PIN + #define BTN_ENC EXP1_09_PIN #if ENABLED(CR10_STOCKDISPLAY) - #define LCD_PINS_RS P1_00 + #define LCD_PINS_RS EXP1_04_PIN - #define BTN_EN1 P0_18 - #define BTN_EN2 P0_15 + #define BTN_EN1 EXP1_08_PIN + #define BTN_EN2 EXP1_06_PIN - #define LCD_PINS_ENABLE P1_22 - #define LCD_PINS_D4 P0_17 + #define LCD_PINS_ENABLE EXP1_03_PIN + #define LCD_PINS_D4 EXP1_05_PIN #elif HAS_SPI_TFT // Config for Classic UI (emulated DOGM) and Color UI - #define TFT_CS_PIN P1_00 - #define TFT_A0_PIN P1_22 - #define TFT_DC_PIN P1_22 - #define TFT_MISO_PIN P0_08 - #define TFT_BACKLIGHT_PIN P0_18 - #define TFT_RESET_PIN P0_16 + #define TFT_CS_PIN EXP1_04_PIN + #define TFT_A0_PIN EXP1_03_PIN + #define TFT_DC_PIN EXP1_03_PIN + #define TFT_MISO_PIN EXP2_10_PIN + #define TFT_BACKLIGHT_PIN EXP1_08_PIN + #define TFT_RESET_PIN EXP1_07_PIN #define LCD_USE_DMA_SPI - #define TOUCH_INT_PIN P0_17 - #define TOUCH_CS_PIN P0_15 + #define TOUCH_INT_PIN EXP1_05_PIN + #define TOUCH_CS_PIN EXP1_06_PIN #define TOUCH_BUTTONS_HW_SPI #define TOUCH_BUTTONS_HW_SPI_DEVICE 2 @@ -278,8 +315,8 @@ #define TFT_QUEUE_SIZE 6144 #endif - #define BTN_EN1 P3_25 - #define BTN_EN2 P3_26 + #define BTN_EN1 EXP2_08_PIN + #define BTN_EN2 EXP2_06_PIN #elif IS_TFTGLCD_PANEL @@ -287,74 +324,74 @@ #undef BTN_ENC #if ENABLED(TFTGLCD_PANEL_SPI) - #define TFTGLCD_CS P3_25 + #define TFTGLCD_CS EXP2_08_PIN #endif #else - #define BTN_EN1 P3_25 - #define BTN_EN2 P3_26 + #define BTN_EN1 EXP2_08_PIN + #define BTN_EN2 EXP2_06_PIN - #define LCD_SDSS P0_28 + #define LCD_SDSS EXP2_07_PIN #if ENABLED(MKS_12864OLED_SSD1306) - #define LCD_PINS_DC P0_17 - #define DOGLCD_CS P0_16 + #define LCD_PINS_DC EXP1_05_PIN + #define DOGLCD_CS EXP1_07_PIN #define DOGLCD_A0 LCD_PINS_DC - #define DOGLCD_SCK P0_15 - #define DOGLCD_MOSI P0_18 + #define DOGLCD_SCK EXP1_06_PIN + #define DOGLCD_MOSI EXP1_08_PIN - #define LCD_PINS_RS P1_00 - #define LCD_PINS_D7 P1_22 + #define LCD_PINS_RS EXP1_04_PIN + #define LCD_PINS_D7 EXP1_03_PIN #define KILL_PIN -1 // NC #else // !MKS_12864OLED_SSD1306 - #define LCD_PINS_RS P0_16 + #define LCD_PINS_RS EXP1_07_PIN - #define LCD_PINS_ENABLE P0_18 - #define LCD_PINS_D4 P0_15 + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN #if ENABLED(FYSETC_MINI_12864) - #define DOGLCD_CS P0_18 - #define DOGLCD_A0 P0_16 - #define DOGLCD_SCK P0_07 - #define DOGLCD_MOSI P0_09 + #define DOGLCD_CS EXP1_08_PIN + #define DOGLCD_A0 EXP1_07_PIN + #define DOGLCD_SCK EXP2_09_PIN + #define DOGLCD_MOSI EXP2_05_PIN #define LCD_BACKLIGHT_PIN -1 #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems // results in LCD soft SPI mode 3, SD soft SPI mode 0 - #define LCD_RESET_PIN P0_15 // Must be high or open for LCD to operate normally. + #define LCD_RESET_PIN EXP1_06_PIN // Must be high or open for LCD to operate normally. #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN P0_17 + #define RGB_LED_R_PIN EXP1_05_PIN #endif #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN P1_00 + #define RGB_LED_G_PIN EXP1_04_PIN #endif #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN P1_22 + #define RGB_LED_B_PIN EXP1_03_PIN #endif #elif ENABLED(FYSETC_MINI_12864_2_1) - #define NEOPIXEL_PIN P0_17 + #define NEOPIXEL_PIN EXP1_05_PIN #endif #else // !FYSETC_MINI_12864 #if ENABLED(MKS_MINI_12864) - #define DOGLCD_CS P0_17 - #define DOGLCD_A0 P1_00 + #define DOGLCD_CS EXP1_05_PIN + #define DOGLCD_A0 EXP1_04_PIN #endif #if IS_ULTIPANEL - #define LCD_PINS_D5 P0_17 - #define LCD_PINS_D6 P1_00 - #define LCD_PINS_D7 P1_22 + #define LCD_PINS_D5 EXP1_05_PIN + #define LCD_PINS_D6 EXP1_04_PIN + #define LCD_PINS_D7 EXP1_03_PIN #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder @@ -370,29 +407,9 @@ #endif // HAS_WIRED_LCD -#ifndef SDCARD_CONNECTION - #define SDCARD_CONNECTION ONBOARD -#endif - -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card - -#if SD_CONNECTION_IS(LCD) || SD_CONNECTION_IS(ONBOARD) - #define SD_DETECT_PIN P0_27 - #define SD_SCK_PIN P0_07 - #define SD_MISO_PIN P0_08 - #define SD_MOSI_PIN P0_09 - #if SD_CONNECTION_IS(ONBOARD) - #define SD_SS_PIN ONBOARD_SD_CS_PIN - #else - #define SD_SS_PIN P0_28 - #endif -#elif SD_CONNECTION_IS(CUSTOM_CABLE) - #error "No custom SD drive cable defined for this board." -#endif - // // Other Pins // //#define PIN_P0_02 P0_02 // AUX1 (Interrupt Capable/ADC/Serial Port 0) //#define PIN_P0_03 P0_03 // AUX1 (Interrupt Capable/ADC/Serial Port 0) -//#define PS_ON_PIN P1_23 // SERVO P1.23 +//#define PS_ON_PIN P1_23 // SERVO0 P1.23 diff --git a/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h index 62127f5504..ce5d5ad7c6 100644 --- a/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h +++ b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h @@ -455,8 +455,6 @@ #define SDCARD_CONNECTION ONBOARD #endif -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card - #if SD_CONNECTION_IS(LCD) #define SD_SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 #define SD_MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 @@ -467,6 +465,7 @@ #define SD_SCK_PIN P0_07 #define SD_MISO_PIN P0_08 #define SD_MOSI_PIN P0_09 + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #define SD_SS_PIN ONBOARD_SD_CS_PIN #elif SD_CONNECTION_IS(CUSTOM_CABLE) #error "No custom SD drive cable defined for this board." diff --git a/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h index 80a91d2cbc..f3ecebde46 100644 --- a/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h +++ b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h @@ -198,8 +198,6 @@ #define SDCARD_CONNECTION ONBOARD #endif -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card - #if SD_CONNECTION_IS(LCD) #define SD_SCK_PIN P0_15 #define SD_MISO_PIN P0_17 @@ -210,6 +208,7 @@ #define SD_SCK_PIN P0_07 #define SD_MISO_PIN P0_08 #define SD_MOSI_PIN P0_09 + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #define SD_SS_PIN ONBOARD_SD_CS_PIN #elif SD_CONNECTION_IS(CUSTOM_CABLE) #error "No custom SD drive cable defined for this board." diff --git a/Marlin/src/pins/lpc1769/pins_BTT_SKR_E3_TURBO.h b/Marlin/src/pins/lpc1769/pins_BTT_SKR_E3_TURBO.h index 44ceb9b7cc..c2d2621bc1 100644 --- a/Marlin/src/pins/lpc1769/pins_BTT_SKR_E3_TURBO.h +++ b/Marlin/src/pins/lpc1769/pins_BTT_SKR_E3_TURBO.h @@ -179,7 +179,7 @@ #endif /** - * ______ + * ------ * 5V | 1 2 | GND * (LCD_EN) P0_18 | 3 4 | P0_17 (LCD_RS) * (LCD_D4) P0_15 | 5 6 P0_20 (BTN_EN2) @@ -203,7 +203,7 @@ /** * Ender 3 V2 display SKR E3 Turbo (EXP1) Ender 3 V2 display --> SKR E3 Turbo - * ______ ______ RX 8 --> 5 P0_15 + * ------ ------ RX 8 --> 5 P0_15 * 5V | 1 2 | GND 5V | 1 2 | GND TX 7 --> 9 P0_16 * (BTN_E1) A | 3 4 | B (BTN_E2) (LCD_EN) P0_18 | 3 4 | P0_17 (LCD_RS) BEEPER 5 --> 10 P2_08 * BEEPER | 5 6 ENT (BTN_ENC) (LCD_D4) P0_15 | 5 6 P0_20 (BTN_EN2) diff --git a/Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h b/Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h index 57b4521453..ea2e0b7082 100644 --- a/Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h +++ b/Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h @@ -229,8 +229,6 @@ #define SDCARD_CONNECTION ONBOARD #endif -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card - #if SD_CONNECTION_IS(LCD) || SD_CONNECTION_IS(ONBOARD) #define SD_SCK_PIN P0_07 // (52) system defined J3-9 & AUX-3 #define SD_MISO_PIN P0_08 // (50) system defined J3-10 & AUX-3 @@ -239,6 +237,7 @@ #define SD_SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) - CS used by Marlin #else #undef SD_DETECT_PIN + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #define SD_SS_PIN ONBOARD_SD_CS_PIN #endif #elif SD_CONNECTION_IS(CUSTOM_CABLE) diff --git a/Marlin/src/pins/lpc1769/pins_MKS_SGEN_L_V2.h b/Marlin/src/pins/lpc1769/pins_MKS_SGEN_L_V2.h index ff7aa11daf..a8a4d2de4e 100644 --- a/Marlin/src/pins/lpc1769/pins_MKS_SGEN_L_V2.h +++ b/Marlin/src/pins/lpc1769/pins_MKS_SGEN_L_V2.h @@ -231,7 +231,7 @@ // Power Supply Control // #if ENABLED(MKS_PWC) - #define PS_ON_PIN P2_00 // SERVO + #define PS_ON_PIN P2_00 // SERVO1 #define KILL_PIN P1_24 // Z+ #define KILL_PIN_STATE HIGH #endif @@ -256,7 +256,7 @@ #endif /** - * _____ _____ + * ----- ----- * (BEEPER) 1.31 | · · | 1.30 (BTN_ENC) (MISO) 0.8 | · · | 0.7 (SD_SCK) * (LCD_EN) 0.18 | · · | 0.16 (LCD_RS) (BTN_EN1) 3.25 | · · | 0.28 (SD_CS2) * (LCD_D4) 0.15 | · · | 0.17 (LCD_D5) (BTN_EN2) 3.26 | · · | 0.9 (SD_MOSI) @@ -265,60 +265,78 @@ * ----- ----- * EXP1 EXP2 */ +#define EXP1_03_PIN P1_22 +#define EXP1_04_PIN P1_00 +#define EXP1_05_PIN P0_17 +#define EXP1_06_PIN P0_15 +#define EXP1_07_PIN P0_16 +#define EXP1_08_PIN P0_18 +#define EXP1_09_PIN P1_30 +#define EXP1_10_PIN P1_31 + +#define EXP2_03_PIN -1 // RESET +#define EXP2_04_PIN P0_27 +#define EXP2_05_PIN P0_09 +#define EXP2_06_PIN P3_26 +#define EXP2_07_PIN P0_28 +#define EXP2_08_PIN P3_25 +#define EXP2_09_PIN P0_07 +#define EXP2_10_PIN P0_08 + #if IS_TFTGLCD_PANEL #if ENABLED(TFTGLCD_PANEL_SPI) - #define TFTGLCD_CS P3_25 + #define TFTGLCD_CS EXP2_08_PIN #endif - #define SD_DETECT_PIN P0_27 + #define SD_DETECT_PIN EXP2_04_PIN #elif HAS_WIRED_LCD - #define BEEPER_PIN P1_31 - #define BTN_ENC P1_30 + #define BEEPER_PIN EXP1_10_PIN + #define BTN_ENC EXP1_09_PIN #if ENABLED(CR10_STOCKDISPLAY) - #define LCD_PINS_RS P1_00 + #define LCD_PINS_RS EXP1_04_PIN - #define BTN_EN1 P0_18 - #define BTN_EN2 P0_15 + #define BTN_EN1 EXP1_08_PIN + #define BTN_EN2 EXP1_06_PIN - #define LCD_PINS_ENABLE P1_22 - #define LCD_PINS_D4 P0_17 + #define LCD_PINS_ENABLE EXP1_03_PIN + #define LCD_PINS_D4 EXP1_05_PIN #else - #define BTN_EN1 P3_25 - #define BTN_EN2 P3_26 + #define BTN_EN1 EXP2_08_PIN + #define BTN_EN2 EXP2_06_PIN - #define LCD_SDSS P0_28 + #define LCD_SDSS EXP2_07_PIN #if ENABLED(MKS_12864OLED_SSD1306) - #define LCD_PINS_DC P0_17 - #define DOGLCD_CS P0_16 + #define LCD_PINS_DC EXP1_05_PIN + #define DOGLCD_CS EXP1_07_PIN #define DOGLCD_A0 LCD_PINS_DC - #define DOGLCD_SCK P0_15 - #define DOGLCD_MOSI P0_18 + #define DOGLCD_SCK EXP1_06_PIN + #define DOGLCD_MOSI EXP1_08_PIN - #define LCD_PINS_RS P1_00 - #define LCD_PINS_D7 P1_22 + #define LCD_PINS_RS EXP1_04_PIN + #define LCD_PINS_D7 EXP1_03_PIN #define KILL_PIN -1 // NC #elif HAS_SPI_TFT // Config for Classic UI (emulated DOGM) and Color UI - #define TFT_CS_PIN P1_00 - #define TFT_A0_PIN P1_22 - #define TFT_DC_PIN P1_22 - #define TFT_MISO_PIN P0_08 - #define TFT_BACKLIGHT_PIN P0_18 - #define TFT_RESET_PIN P0_16 + #define TFT_CS_PIN EXP1_04_PIN + #define TFT_A0_PIN EXP1_03_PIN + #define TFT_DC_PIN EXP1_03_PIN + #define TFT_MISO_PIN EXP2_10_PIN + #define TFT_BACKLIGHT_PIN EXP1_08_PIN + #define TFT_RESET_PIN EXP1_07_PIN #define LCD_USE_DMA_SPI - #define TOUCH_INT_PIN P0_17 - #define TOUCH_CS_PIN P0_15 + #define TOUCH_INT_PIN EXP1_05_PIN + #define TOUCH_CS_PIN EXP1_06_PIN #define TOUCH_BUTTONS_HW_SPI #define TOUCH_BUTTONS_HW_SPI_DEVICE 2 @@ -335,50 +353,50 @@ #else // !MKS_12864OLED_SSD1306 - #define LCD_PINS_RS P0_16 + #define LCD_PINS_RS EXP1_07_PIN - #define LCD_PINS_ENABLE P0_18 - #define LCD_PINS_D4 P0_15 + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN #if ENABLED(FYSETC_MINI_12864) - #define DOGLCD_CS P0_18 - #define DOGLCD_A0 P0_16 - #define DOGLCD_SCK P0_07 - #define DOGLCD_MOSI P0_09 + #define DOGLCD_CS EXP1_08_PIN + #define DOGLCD_A0 EXP1_07_PIN + #define DOGLCD_SCK EXP2_09_PIN + #define DOGLCD_MOSI EXP2_05_PIN #define LCD_BACKLIGHT_PIN -1 #define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems // results in LCD soft SPI mode 3, SD soft SPI mode 0 - #define LCD_RESET_PIN P0_15 // Must be high or open for LCD to operate normally. + #define LCD_RESET_PIN EXP1_06_PIN // Must be high or open for LCD to operate normally. #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN P0_17 + #define RGB_LED_R_PIN EXP1_05_PIN #endif #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN P1_00 + #define RGB_LED_G_PIN EXP1_04_PIN #endif #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN P1_22 + #define RGB_LED_B_PIN EXP1_03_PIN #endif #elif ENABLED(FYSETC_MINI_12864_2_1) - #define NEOPIXEL_PIN P0_17 + #define NEOPIXEL_PIN EXP1_05_PIN #endif #else // !FYSETC_MINI_12864 #if ENABLED(MKS_MINI_12864) - #define DOGLCD_CS P0_17 - #define DOGLCD_A0 P1_00 + #define DOGLCD_CS EXP1_05_PIN + #define DOGLCD_A0 EXP1_04_PIN #endif #if IS_ULTIPANEL - #define LCD_PINS_D5 P0_17 - #define LCD_PINS_D6 P1_00 - #define LCD_PINS_D7 P1_22 + #define LCD_PINS_D5 EXP1_05_PIN + #define LCD_PINS_D6 EXP1_04_PIN + #define LCD_PINS_D7 EXP1_03_PIN #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder @@ -398,17 +416,16 @@ #define SDCARD_CONNECTION ONBOARD #endif -#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card - #if SD_CONNECTION_IS(LCD) || SD_CONNECTION_IS(ONBOARD) - #define SD_DETECT_PIN P0_27 - #define SD_SCK_PIN P0_07 - #define SD_MISO_PIN P0_08 - #define SD_MOSI_PIN P0_09 + #define SD_DETECT_PIN EXP2_04_PIN + #define SD_SCK_PIN EXP2_09_PIN + #define SD_MISO_PIN EXP2_10_PIN + #define SD_MOSI_PIN EXP2_05_PIN #if SD_CONNECTION_IS(ONBOARD) + #define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card #define SD_SS_PIN ONBOARD_SD_CS_PIN #else - #define SD_SS_PIN P0_28 + #define SD_SS_PIN EXP2_07_PIN #endif #elif SD_CONNECTION_IS(CUSTOM_CABLE) #error "No custom SD drive cable defined for this board." @@ -419,4 +436,4 @@ // //#define PIN_P0_02 P0_02 // AUX1 (Interrupt Capable/ADC/Serial Port 0) //#define PIN_P0_03 P0_03 // AUX1 (Interrupt Capable/ADC/Serial Port 0) -//#define PS_ON_PIN P1_23 // SERVO P1.23 +//#define PS_ON_PIN P1_23 // SERVO0 P1.23 diff --git a/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h b/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h index 22a6613329..dc7dcd6db6 100644 --- a/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h +++ b/Marlin/src/pins/lpc1769/pins_TH3D_EZBOARD.h @@ -156,7 +156,7 @@ // /** - * ______ + * ------ * 5V | 1 2 | GND * P0_18 | 3 4 | P0_16 * P0_15 | 5 6 P3_25 @@ -181,7 +181,7 @@ #define EXP1_10_PIN P1_31 #if ENABLED(CR10_STOCKDISPLAY) - /** ______ + /** ------ * 5V | 1 2 | GND * LCD_EN | 3 4 | LCD_RS * LCD_D4 | 5 6 EN2 @@ -196,7 +196,7 @@ #define KILL_PIN EXP1_07_PIN #elif ENABLED(MKS_MINI_12864) - /** ______ + /** ------ * 5V | 1 2 | GND * SPI-MOSI | 3 4 | SPI-CS * A0 | 5 6 EN2 diff --git a/Marlin/src/pins/ramps/pins_RAMPS.h b/Marlin/src/pins/ramps/pins_RAMPS.h index b141fdbf85..1683ccf5c8 100644 --- a/Marlin/src/pins/ramps/pins_RAMPS.h +++ b/Marlin/src/pins/ramps/pins_RAMPS.h @@ -434,7 +434,7 @@ /** * LCD adapter. Please note: These comes in two variants. The socket keys can be * on either side, and may be backwards on some boards / displays. - * _____ _____ + * ----- ----- * D37 |10 9 | D35 (MISO) D50 |10 9 | D52 (SCK) * D17 | 8 7 | D16 D31 | 8 7 | D53 * D23 6 5 D25 D33 6 5 D51 (MOSI) @@ -778,7 +778,7 @@ * FYSETC TFT-81050 display pinout * * Board Display - * _____ _____ + * ----- ----- * (SCK) D52 | 1 2 | D50 (MISO) MISO | 1 2 | SCK * (SD_CS) D53 | 3 4 | D33 (BNT_EN2) (BNT_EN2) MOD_RESET | 3 4 | SD_CS * (MOSI) D51 | 5 6 D31 (BNT_EN1) (BNT_EN1) LCD_CS | 5 6 MOSI diff --git a/Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h b/Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h index 225392de1b..d4915c9cca 100644 --- a/Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h +++ b/Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h @@ -137,7 +137,7 @@ /** * EXP1 Connector EXP1 as CR10 STOCKDISPLAY - * _____ _____ + * ----- ----- * PA4 | 6 5 | PC0 BEEPER_PIN | 6 5 | BTN_ENC * PD3 | 7 4 | RESET BTN_EN1 | 7 4 | RESET * PD2 8 3 | PA1 BTN_EN2 8 3 | LCD_PINS_D4 (ST9720 CLK) diff --git a/Marlin/src/pins/stm32f1/pins_BTT_SKR_CR6.h b/Marlin/src/pins/stm32f1/pins_BTT_SKR_CR6.h index bd5f2068f1..c614a2dbb9 100644 --- a/Marlin/src/pins/stm32f1/pins_BTT_SKR_CR6.h +++ b/Marlin/src/pins/stm32f1/pins_BTT_SKR_CR6.h @@ -158,8 +158,6 @@ // SD Card // -#define HAS_ONBOARD_SD - #ifndef SDCARD_CONNECTION #define SDCARD_CONNECTION ONBOARD #endif diff --git a/Marlin/src/pins/stm32f1/pins_BTT_SKR_E3_DIP.h b/Marlin/src/pins/stm32f1/pins_BTT_SKR_E3_DIP.h index 6ed2869141..dae43d3c13 100644 --- a/Marlin/src/pins/stm32f1/pins_BTT_SKR_E3_DIP.h +++ b/Marlin/src/pins/stm32f1/pins_BTT_SKR_E3_DIP.h @@ -156,7 +156,7 @@ #define USB_CONNECT_INVERTING false /** - * _____ + * ----- * 5V | 1 2 | GND * (LCD_EN) PB7 | 3 4 | PB8 (LCD_RS) * (LCD_D4) PB9 | 5 6 PA10 (BTN_EN2) @@ -195,7 +195,7 @@ #elif EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY) /** Creality Ender-2 display pinout - * _____ + * ----- * 5V | 1 2 | GND * (MOSI) PB7 | 3 4 | PB8 (LCD_RS) * (LCD_A0) PB9 | 5 6 PA10 (BTN_EN2) @@ -229,7 +229,7 @@ /** FYSETC TFT TFT81050 display pinout * * Board Display - * _____ _____ + * ----- ----- * 5V | 1 2 | GND (SPI1-MISO) MISO | 1 2 | SCK (SPI1-SCK) * (FREE) PB7 | 3 4 | PB8 (LCD_CS) (PA9) MOD_RESET | 3 4 | SD_CS (PA10) * (FREE) PB9 | 5 6 PA10 (SD_CS) (PB8) LCD_CS | 5 6 MOSI (SPI1-MOSI) diff --git a/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h b/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h index 8f305542a9..fe4fd3a4a7 100644 --- a/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h +++ b/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h @@ -117,7 +117,7 @@ /** * SKR Mini E3 V1.0, V1.2 SKR Mini E3 V2.0 - * ______ ______ + * ------ ------ * 5V | 1 2 | GND 5V | 1 2 | GND * (LCD_EN) PB7 | 3 4 | PB8 (LCD_RS) (LCD_EN) PB15 | 3 4 | PB8 (LCD_RS) * (LCD_D4) PB9 | 5 6 PA10 (BTN_EN2) (LCD_D4) PB9 | 5 6 PA10 (BTN_EN2) @@ -134,7 +134,7 @@ #define EXP1_3 PB7 #endif -#if ENABLED(DWIN_CREALITY_LCD) +#if EITHER(DWIN_CREALITY_LCD, IS_DWIN_MARLINUI) /** * ------ ------ ------ * VCC | 1 2 | GND VCC | 1 2 | GND GND | 2 1 | VCC @@ -205,7 +205,7 @@ * TFTGLCD_PANEL_SPI display pinout * * Board Display - * ______ ______ + * ------ ------ * 5V | 1 2 | GND (SPI1-MISO) MISO | 1 2 | SCK (SPI1-SCK) * (FREE) PB7 | 3 4 | PB8 (LCD_CS) (PA9) LCD_CS | 3 4 | SD_CS (PA10) * (FREE) PB9 | 5 6 | PA10 (SD_CS) (FREE) | 5 6 | MOSI (SPI1-MOSI) @@ -248,7 +248,7 @@ * FYSETC TFT TFT81050 display pinout * * Board Display - * ______ ______ + * ------ ------ * 5V | 1 2 | GND (SPI1-MISO) MISO | 1 2 | SCK (SPI1-SCK) * (FREE) PB7 | 3 4 | PB8 (LCD_CS) (PA9) MOD_RESET | 3 4 | SD_CS (PA10) * (FREE) PB9 | 5 6 | PA10 (SD_CS) (PB8) LCD_CS | 5 6 | MOSI (SPI1-MOSI) diff --git a/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_V1_1.h b/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_V1_1.h index 6b3d2832d0..441f9350e3 100644 --- a/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_V1_1.h +++ b/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_V1_1.h @@ -98,7 +98,7 @@ // /** - * _____ _____ + * ----- ----- * NC | · · | GND 5V | · · | GND * RESET | · · | PB9 (SD_DETECT) (LCD_D7) PC14 | · · | PC15 (LCD_D6) * (MOSI) PB5 | · · | PB8 (BTN_EN2) (LCD_D5) PB7 | · · | PC13 (LCD_D4) diff --git a/Marlin/src/pins/stm32f1/pins_CCROBOT_MEEB_3DP.h b/Marlin/src/pins/stm32f1/pins_CCROBOT_MEEB_3DP.h index 7b61f55d4f..c2edcd3678 100644 --- a/Marlin/src/pins/stm32f1/pins_CCROBOT_MEEB_3DP.h +++ b/Marlin/src/pins/stm32f1/pins_CCROBOT_MEEB_3DP.h @@ -122,7 +122,7 @@ #define NEOPIXEL_PIN PC7 // The NEOPIXEL LED driving pin /** - * 1 _____ 2 + * 1 ----- 2 * PB5 | · · | PB6 * PA2 | · · | RESET * PA3 | · · | PB8 diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h index 0437156c0c..056fdf4c29 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h @@ -194,7 +194,6 @@ //#define LCD_LED_PIN PB2 #ifndef BEEPER_PIN #define BEEPER_PIN PB13 - //#undef SPEAKER #endif #elif ENABLED(DWIN_VET6_CREALITY_LCD) diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h index f971f65628..7694130a3e 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h @@ -156,35 +156,67 @@ #define SDIO_SUPPORT #define NO_SD_HOST_DRIVE // This board's SD is only seen by the printer -#if ENABLED(CR10_STOCKDISPLAY) && NONE(RET6_12864_LCD, VET6_12864_LCD) - #error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for CR10_STOCKDISPLAY with the Creality V4 controller." -#endif +#if ENABLED(CR10_STOCKDISPLAY) -#if ENABLED(RET6_12864_LCD) + #if ENABLED(RET6_12864_LCD) - // RET6 12864 LCD - #define LCD_PINS_RS PB12 - #define LCD_PINS_ENABLE PB15 - #define LCD_PINS_D4 PB13 + /** + * RET6 12864 LCD + * ------ + * PC6 |10 9 | PB2 + * PB10 | 8 7 | PE8 + * PB14 | 6 5 | PB13 + * PB12 | 4 3 | PB15 + * GND | 2 1 | 5V + * ------ + * EXP1 + */ + #define EXP1_03_PIN PB15 + #define EXP1_04_PIN PB12 + #define EXP1_05_PIN PB13 + #define EXP1_06_PIN PB14 + #define EXP1_07_PIN PE8 + #define EXP1_08_PIN PB10 + #define EXP1_09_PIN PB2 + #define EXP1_10_PIN PC6 - #define BTN_ENC PB2 - #define BTN_EN1 PB10 - #define BTN_EN2 PB14 + #define BEEPER_PIN EXP1_10_PIN - #define BEEPER_PIN PC6 + #elif ENABLED(VET6_12864_LCD) -#elif ENABLED(VET6_12864_LCD) + /** + * VET6 12864 LCD + * ------ + * ? |10 9 | PC5 + * PB10 | 8 7 | ? + * PA6 | 6 5 | PA5 + * PA4 | 4 3 | PA7 + * GND | 2 1 | 5V + * ------ + * EXP1 + */ + #define EXP1_03_PIN PA7 + #define EXP1_04_PIN PA4 + #define EXP1_05_PIN PA5 + #define EXP1_06_PIN PA6 + #define EXP1_07_PIN -1 + #define EXP1_08_PIN PB10 + #define EXP1_09_PIN PC5 + #define EXP1_10_PIN -1 - // VET6 12864 LCD - #define LCD_PINS_RS PA4 - #define LCD_PINS_ENABLE PA7 - #define LCD_PINS_D4 PA5 + #else + #error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for CR10_STOCKDISPLAY with the Creality V4 controller." + #endif - #define BTN_ENC PC5 - #define BTN_EN1 PB10 - #define BTN_EN2 PA6 + #define LCD_PINS_RS EXP1_04_PIN + #define LCD_PINS_ENABLE EXP1_03_PIN + #define LCD_PINS_D4 EXP1_05_PIN -#elif ENABLED(DWIN_CREALITY_LCD) + #define BTN_ENC EXP1_09_PIN + #define BTN_EN1 EXP1_08_PIN + #define BTN_EN2 EXP1_06_PIN + +#elif EITHER(DWIN_CREALITY_LCD, IS_DWIN_MARLINUI) // RET6 DWIN ENCODER LCD #define BTN_ENC PB14 @@ -194,7 +226,6 @@ //#define LCD_LED_PIN PB2 #ifndef BEEPER_PIN #define BEEPER_PIN PB13 - #undef SPEAKER #endif #elif ENABLED(DWIN_VET6_CREALITY_LCD) diff --git a/Marlin/src/pins/stm32f1/pins_FYSETC_CHEETAH.h b/Marlin/src/pins/stm32f1/pins_FYSETC_CHEETAH.h index 552ad9ac57..2060ad86fe 100644 --- a/Marlin/src/pins/stm32f1/pins_FYSETC_CHEETAH.h +++ b/Marlin/src/pins/stm32f1/pins_FYSETC_CHEETAH.h @@ -132,8 +132,8 @@ /* * EXP1 pinout for the LCD according to Fysetcs schematic for the Cheetah board -* _____ -* (Beeper) PC9 | 1 2 | PC12 (BTN_ENC) +* ----- +* (BEEPER) PC9 | 1 2 | PC12 (BTN_ENC) * (BTN_EN2) PC11 | 3 4 | PB14 (LCD_RS / MISO) * (BTN_EN1) PC10 5 6 | PB13 (SCK) * (LCD_EN) PB12 | 7 8 | PB15 (MOSI) diff --git a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h index 2d8b0abce4..a07cfe0120 100644 --- a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h +++ b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h @@ -133,7 +133,7 @@ #endif /** - * _____ _____ _____ + * ----- ----- ----- * (BEEPER) PC1 | 1 2 | PC3 (BTN_ENC) (MISO) PB14 | 1 2 | PB13 (SD_SCK) 5V | 1 2 | GND * (LCD_EN) PA4 | 3 4 | PA5 (LCD_RS) (BTN_EN1) PB11 | 3 4 | PA15 (SD_SS) (LCD_EN) PA4 | 3 4 | PA5 (LCD_RS) * (LCD_D4) PA6 | 5 6 PA7 (LCD_D5) (BTN_EN2) PB0 | 5 6 PB15 (SD_MOSI) (LCD_D4) PA6 | 5 6 PB0 (BTN_EN2) diff --git a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h index 1f3efee6e5..6e19b441c6 100644 --- a/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h +++ b/Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h @@ -299,14 +299,16 @@ #endif -#ifndef BOARD_ST7920_DELAY_1 - #define BOARD_ST7920_DELAY_1 DELAY_NS(125) -#endif -#ifndef BOARD_ST7920_DELAY_2 - #define BOARD_ST7920_DELAY_2 DELAY_NS(125) -#endif -#ifndef BOARD_ST7920_DELAY_3 - #define BOARD_ST7920_DELAY_3 DELAY_NS(125) +#if HAS_MARLINUI_U8GLIB + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(125) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(125) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(125) + #endif #endif #define HAS_SPI_FLASH 1 diff --git a/Marlin/src/pins/stm32f1/pins_ZM3E2_V1_0.h b/Marlin/src/pins/stm32f1/pins_ZM3E2_V1_0.h index bad5db7125..0d413d3651 100644 --- a/Marlin/src/pins/stm32f1/pins_ZM3E2_V1_0.h +++ b/Marlin/src/pins/stm32f1/pins_ZM3E2_V1_0.h @@ -201,9 +201,9 @@ #define BTN_EN1 EXP1_03_PIN #define BTN_EN2 EXP1_06_PIN #define BTN_ENC EXP1_04_PIN - #define BOARD_ST7920_DELAY_1 DELAY_NS(125) - #define BOARD_ST7920_DELAY_2 DELAY_NS(200) - #define BOARD_ST7920_DELAY_3 DELAY_NS(125) + #define BOARD_ST7920_DELAY_1 DELAY_NS(125) + #define BOARD_ST7920_DELAY_2 DELAY_NS(200) + #define BOARD_ST7920_DELAY_3 DELAY_NS(125) #elif EITHER(ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) diff --git a/Marlin/src/pins/stm32f1/pins_ZM3E4_V1_0.h b/Marlin/src/pins/stm32f1/pins_ZM3E4_V1_0.h index 8a6bb4b5f8..3674f10ce7 100644 --- a/Marlin/src/pins/stm32f1/pins_ZM3E4_V1_0.h +++ b/Marlin/src/pins/stm32f1/pins_ZM3E4_V1_0.h @@ -332,9 +332,9 @@ #endif #if HAS_MARLINUI_U8GLIB - #define BOARD_ST7920_DELAY_1 DELAY_NS(125) - #define BOARD_ST7920_DELAY_2 DELAY_NS(250) - #define BOARD_ST7920_DELAY_3 DELAY_NS(125) + #define BOARD_ST7920_DELAY_1 DELAY_NS(125) + #define BOARD_ST7920_DELAY_2 DELAY_NS(250) + #define BOARD_ST7920_DELAY_3 DELAY_NS(125) #endif // Remap SERVO0 PIN for BLTouch diff --git a/Marlin/src/pins/stm32f1/pins_ZM3E4_V2_0.h b/Marlin/src/pins/stm32f1/pins_ZM3E4_V2_0.h index 5bbf43bbfa..017195edee 100644 --- a/Marlin/src/pins/stm32f1/pins_ZM3E4_V2_0.h +++ b/Marlin/src/pins/stm32f1/pins_ZM3E4_V2_0.h @@ -305,9 +305,9 @@ #endif #if HAS_MARLINUI_U8GLIB - #define BOARD_ST7920_DELAY_1 DELAY_NS(200) // Tclk_fall <200ns - #define BOARD_ST7920_DELAY_2 DELAY_NS(250) // Tdata_width >200ns - #define BOARD_ST7920_DELAY_3 DELAY_NS(200) // Tclk_rise <200ns + #define BOARD_ST7920_DELAY_1 DELAY_NS(200) // Tclk_fall <200ns + #define BOARD_ST7920_DELAY_2 DELAY_NS(250) // Tdata_width >200ns + #define BOARD_ST7920_DELAY_3 DELAY_NS(200) // Tclk_rise <200ns #endif // Remap SERVO0 PIN for BLTouch diff --git a/Marlin/src/pins/stm32f4/pins_BTT_E3_RRF.h b/Marlin/src/pins/stm32f4/pins_BTT_E3_RRF.h index 481c38f515..a768088c37 100644 --- a/Marlin/src/pins/stm32f4/pins_BTT_E3_RRF.h +++ b/Marlin/src/pins/stm32f4/pins_BTT_E3_RRF.h @@ -183,7 +183,7 @@ /** * BTT E3 RRF - * _____ + * ----- * 5V | 1 2 | GND * (LCD_EN) PE11 | 3 4 | PB1 (LCD_RS) * (LCD_D4) PE10 | 5 6 PB2 (BTN_EN2) @@ -248,7 +248,7 @@ * TFTGLCD_PANEL_SPI display pinout * * Board Display - * _____ _____ + * ----- ----- * 5V | 1 2 | GND (SPI1-MISO) MISO | 1 2 | SCK (SPI1-SCK) * (FREE) PE11 | 3 4 | PB1 (LCD_CS) (PE7) LCD_CS | 3 4 | SD_CS (PB2) * (FREE) PE10 | 5 6 | PB2 (SD_CS) (FREE) | 5 6 | MOSI (SPI1-MOSI) @@ -303,7 +303,7 @@ /** FYSETC TFT TFT81050 display pinout * * Board Display - * _____ _____ + * ----- ----- * 5V | 1 2 | GND (SPI1-MISO) MISO | 1 2 | SCK (SPI1-SCK) * (FREE) PE11 | 3 4 | PB1 (LCD_CS) (PE7) MOD_RESET | 3 4 | SD_CS (PB2) * (FREE) PE10 | 5 6 | PB2 (SD_CS) (PB1) LCD_CS | 5 6 | MOSI (SPI1-MOSI) diff --git a/Marlin/src/pins/stm32f4/pins_BTT_OCTOPUS_V1_common.h b/Marlin/src/pins/stm32f4/pins_BTT_OCTOPUS_V1_common.h index 92e7b5d374..ec9ca32f7e 100644 --- a/Marlin/src/pins/stm32f4/pins_BTT_OCTOPUS_V1_common.h +++ b/Marlin/src/pins/stm32f4/pins_BTT_OCTOPUS_V1_common.h @@ -311,7 +311,7 @@ #endif /** - * ______ ______ + * ------ ------ * NC | 1 2 | GND 5V | 1 2 | GND * RESET | 3 4 | PC15 (SD_DETECT) (LCD_D7) PE15 | 3 4 | PE14 (LCD_D6) * (MOSI) PA7 | 5 6 PB1 (BTN_EN2) (LCD_D5) PE13 | 5 6 PE12 (LCD_D4) @@ -366,7 +366,7 @@ #if ENABLED(BTT_MOTOR_EXPANSION) /** - * ______ ______ + * ------ ------ * NC | 1 2 | GND NC | 1 2 | GND * NC | 3 4 | M1EN M2EN | 3 4 | M3EN * M1STP | 5 6 M1DIR M1RX | 5 6 M1DIAG diff --git a/Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h b/Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h index e43cc4e5a0..6daa34e059 100644 --- a/Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h +++ b/Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h @@ -367,7 +367,7 @@ #endif #if ENABLED(BTT_MOTOR_EXPANSION) - /** _____ _____ + /** ----- ----- * NC | . . | GND NC | . . | GND * NC | . . | M1EN M2EN | . . | M3EN * M1STP | . . M1DIR M1RX | . . M1DIAG diff --git a/Marlin/src/pins/stm32f4/pins_BTT_SKR_V2_0_common.h b/Marlin/src/pins/stm32f4/pins_BTT_SKR_V2_0_common.h index dc2ee99aff..e049f8fbd9 100644 --- a/Marlin/src/pins/stm32f4/pins_BTT_SKR_V2_0_common.h +++ b/Marlin/src/pins/stm32f4/pins_BTT_SKR_V2_0_common.h @@ -350,7 +350,7 @@ #endif #if ENABLED(BTT_MOTOR_EXPANSION) - /** _____ _____ + /** ----- ----- * NC | . . | GND NC | . . | GND * NC | . . | M1EN M2EN | . . | M3EN * M1STP | . . M1DIR M1RX | . . M1DIAG diff --git a/Marlin/src/pins/stm32f4/pins_FLYF407ZG.h b/Marlin/src/pins/stm32f4/pins_FLYF407ZG.h index 728e753543..27ad7179df 100644 --- a/Marlin/src/pins/stm32f4/pins_FLYF407ZG.h +++ b/Marlin/src/pins/stm32f4/pins_FLYF407ZG.h @@ -175,17 +175,39 @@ #define FAN4_PIN PE13 #define FAN5_PIN PB11 +/** + * ------ ------ + * PB10 |10 9 | PE15 PB14 |10 9 | PB13 + * PE14 | 8 7 | PE12 PC5 | 8 7 | PF11 + * PE10 6 5 | PE9 PC4 6 5 | PB15 + * PE8 | 4 3 | PE7 PB2 | 4 3 | RESET + * GND | 2 1 | 5V GND | 2 1 | NC + * ------ ------ + * EXP1 EXP2 + */ + +#define EXP1_03_PIN PE7 +#define EXP1_04_PIN PE8 +#define EXP1_05_PIN PE9 +#define EXP1_06_PIN PE10 +#define EXP1_07_PIN PE12 +#define EXP1_08_PIN PE14 +#define EXP1_09_PIN PE15 +#define EXP1_10_PIN PB10 + +#define EXP2_03_PIN -1 // RESET +#define EXP2_04_PIN PB2 +#define EXP2_05_PIN PB15 +#define EXP2_06_PIN PC4 +#define EXP2_07_PIN PF11 +#define EXP2_08_PIN PC5 +#define EXP2_09_PIN PB13 +#define EXP2_10_PIN PB14 + // // Onboard SD support // - -#define SDIO_D0_PIN PC8 -#define SDIO_D1_PIN PC9 //#define SD_CARD_DETECT_PIN PC13 -#define SDIO_D2_PIN PC10 -#define SDIO_D3_PIN PC11 -#define SDIO_CK_PIN PC12 -#define SDIO_CMD_PIN PD2 #ifndef SDCARD_CONNECTION #define SDCARD_CONNECTION ONBOARD @@ -194,37 +216,37 @@ #if SD_CONNECTION_IS(ONBOARD) #define SDIO_SUPPORT // Use SDIO for onboard SD - #ifndef SDIO_SUPPORT + + #if DISABLED(SDIO_SUPPORT) #define SOFTWARE_SPI // Use soft SPI for onboard SD - #define SDSS SDIO_D3_PIN - #define SD_SCK_PIN SDIO_CK_PIN - #define SD_MISO_PIN SDIO_D0_PIN - #define SD_MOSI_PIN SDIO_CMD_PIN + #define SDSS PC11 + #define SD_SCK_PIN PC12 + #define SD_MISO_PIN PC8 + #define SD_MOSI_PIN PD2 #endif #elif SD_CONNECTION_IS(LCD) - #define SD_SCK_PIN PB13 - #define SD_MISO_PIN PB14 - #define SD_MOSI_PIN PB15 - #define SDSS PF11 - #define SD_DETECT_PIN PB2 + #define SD_SCK_PIN EXP2_09_PIN + #define SD_MISO_PIN EXP2_10_PIN + #define SD_MOSI_PIN EXP2_05_PIN + #define SDSS EXP2_07_PIN + #define SD_DETECT_PIN EXP2_04_PIN #endif // // Trinamic Software SPI // - #if ENABLED(TMC_USE_SW_SPI) - #ifndef TMC_SW_MOSI - #define TMC_SW_MOSI PB15 + #ifndef TMC_SW_SCK + #define TMC_SW_SCK EXP2_09_PIN #endif #ifndef TMC_SW_MISO - #define TMC_SW_MISO PB14 + #define TMC_SW_MISO EXP2_10_PIN #endif - #ifndef TMC_SW_SCK - #define TMC_SW_SCK PB13 + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI EXP2_05_PIN #endif #endif @@ -264,17 +286,18 @@ // // LCD / Controller // - -#define BEEPER_PIN PB10 -#define LCD_PINS_RS PE12 -#define LCD_PINS_ENABLE PE14 -#define LCD_PINS_D4 PE10 -#define LCD_PINS_D5 PE9 -#define LCD_PINS_D6 PE8 -#define LCD_PINS_D7 PE7 -#define BTN_EN1 PC4 -#define BTN_EN2 PC5 -#define BTN_ENC PE15 +#if IS_RRD_SC + #define BEEPER_PIN EXP1_10_PIN + #define LCD_PINS_RS EXP1_07_PIN + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN + #define LCD_PINS_D5 EXP1_05_PIN + #define LCD_PINS_D6 EXP1_04_PIN + #define LCD_PINS_D7 EXP1_03_PIN + #define BTN_EN1 EXP2_06_PIN + #define BTN_EN2 EXP2_08_PIN + #define BTN_ENC EXP1_09_PIN +#endif // // Filament runout @@ -285,12 +308,14 @@ // // ST7920 Delays // -#ifndef BOARD_ST7920_DELAY_1 - #define BOARD_ST7920_DELAY_1 DELAY_NS(96) -#endif -#ifndef BOARD_ST7920_DELAY_2 - #define BOARD_ST7920_DELAY_2 DELAY_NS(48) -#endif -#ifndef BOARD_ST7920_DELAY_3 - #define BOARD_ST7920_DELAY_3 DELAY_NS(715) +#if HAS_MARLINUI_U8GLIB + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(96) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(48) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(715) + #endif #endif diff --git a/Marlin/src/pins/stm32f4/pins_FYSETC_CHEETAH_V20.h b/Marlin/src/pins/stm32f4/pins_FYSETC_CHEETAH_V20.h index ef1c14aae0..b50f1e4966 100644 --- a/Marlin/src/pins/stm32f4/pins_FYSETC_CHEETAH_V20.h +++ b/Marlin/src/pins/stm32f4/pins_FYSETC_CHEETAH_V20.h @@ -138,7 +138,7 @@ #endif /** - * _____ _____ + * ----- ----- * 5V | 1 2 | GND 5V | 1 2 | GND * RESET | 3 4 | PC3 (SD_DETECT) (LCD_D7) PB7 | 3 4 | PB6 (LCD_D6) * (SD_MOSI) PA7 5 6 | PC11 (BTN_EN2) (LCD_D5) PB14 5 6 | PB13 (LCD_D4) @@ -149,7 +149,7 @@ */ /** -* _____ +* ----- * (BEEPER) PC9 | 1 2 | PC12 (BTN_ENC) * (BTN_EN1) PC10 | 3 4 | PB14 (LCD_D5/MISO) * (BTN_EN2) PC11 5 6 | PB13 (LCD_D4/SCK) @@ -258,7 +258,7 @@ #define BOARD_ST7920_DELAY_2 DELAY_NS(48) #endif #ifndef BOARD_ST7920_DELAY_3 - #define BOARD_ST7920_DELAY_3 DELAY_NS(600) + #define BOARD_ST7920_DELAY_3 DELAY_NS(600) #endif #endif diff --git a/Marlin/src/pins/stm32f4/pins_FYSETC_S6.h b/Marlin/src/pins/stm32f4/pins_FYSETC_S6.h index 9de62d372a..9ce8d33fa8 100644 --- a/Marlin/src/pins/stm32f4/pins_FYSETC_S6.h +++ b/Marlin/src/pins/stm32f4/pins_FYSETC_S6.h @@ -192,12 +192,12 @@ //#define KILL_PIN PC5 /** - * ______ ______ - * 5V | 1 2 | GND 5V | 1 2 | GND - * PD1 | 3 4 | PD0 RESET | 3 4 | PB10 - * PC12 | 5 6 PC10 PA7 | 5 6 PC7 - * PD2 | 7 8 | PC11 PA4 | 7 8 | PC6 - * PA8 | 9 10 | PC9 PA5 | 9 10 | PA6 + * ------ ------ + * PC9 |10 9 | PA8 PA6 |10 9 | PA5 + * PC11 | 8 7 | PD2 PC6 | 8 7 | PA4 + * PC10 | 6 5 PC12 PC7 | 6 5 PA7 + * PD0 | 4 3 | PD1 PB10 | 4 3 | RESET + * GND | 2 1 | 5V GND | 2 1 | 5V * ------ ------ * EXP1 EXP2 */ @@ -315,9 +315,15 @@ // Alter timing for graphical display #if HAS_MARLINUI_U8GLIB - #define BOARD_ST7920_DELAY_1 DELAY_NS(96) - #define BOARD_ST7920_DELAY_2 DELAY_NS(48) - #define BOARD_ST7920_DELAY_3 DELAY_NS(640) + #ifndef BOARD_ST7920_DELAY_1 + #define BOARD_ST7920_DELAY_1 DELAY_NS(96) + #endif + #ifndef BOARD_ST7920_DELAY_2 + #define BOARD_ST7920_DELAY_2 DELAY_NS(48) + #endif + #ifndef BOARD_ST7920_DELAY_3 + #define BOARD_ST7920_DELAY_3 DELAY_NS(640) + #endif #endif #ifndef RGB_LED_R_PIN diff --git a/Marlin/src/pins/stm32f4/pins_MKS_MONSTER8.h b/Marlin/src/pins/stm32f4/pins_MKS_MONSTER8.h index adc8b2a8bd..38714d7da9 100644 --- a/Marlin/src/pins/stm32f4/pins_MKS_MONSTER8.h +++ b/Marlin/src/pins/stm32f4/pins_MKS_MONSTER8.h @@ -225,22 +225,46 @@ // Power Supply Control // #if ENABLED(MKS_PWC) - #define PS_ON_PIN PW_OFF - #define KILL_PIN PW_DET + #define PS_ON_PIN PW_OFF + #define KILL_PIN PW_DET #define KILL_PIN_STATE HIGH #endif // Random Info #define USB_SERIAL -1 // USB Serial +/** + * ------ ------ + * (BEEPER) PB2 |10 9 | PE10 (BTN_ENC) (SPI1 MISO) PA6 |10 9 | PA5 (SPI1 SCK) + * (LCD_EN) PE11 | 8 7 | PD10 (LCD_RS) (BTN_EN1) PE9 | 8 7 | PA4 (SPI1 CS) + * (LCD_D4) PD9 | 6 5 PD8 (LCD_D5) (BTN_EN2) PE8 | 6 5 PA7 (SPI1 MOSI) + * (LCD_D6) PE15 | 4 3 | PE7 (LCD_D7) (SPI1_RS) PB11 | 4 3 | RESET + * GND | 2 1 | 5V GND | 2 1 | 3.3V + * ------ ------ + * EXP1 EXP2 + */ +#define EXP1_03_PIN PE7 +#define EXP1_04_PIN PE15 +#define EXP1_05_PIN PD8 +#define EXP1_06_PIN PD9 +#define EXP1_07_PIN PD10 +#define EXP1_08_PIN PE11 +#define EXP1_09_PIN PE10 +#define EXP1_10_PIN PB2 + +#define EXP2_03_PIN -1 // RESET +#define EXP2_04_PIN PB11 +#define EXP2_05_PIN PA7 +#define EXP2_06_PIN PE8 +#define EXP2_07_PIN PA4 +#define EXP2_08_PIN PE9 +#define EXP2_09_PIN PA5 +#define EXP2_10_PIN PA6 + #ifndef SDCARD_CONNECTION #define SDCARD_CONNECTION ONBOARD #endif -// -// Onboard SD card -// -// detect pin doesn't work when ONBOARD and NO_SD_HOST_DRIVE disabled #if SD_CONNECTION_IS(ONBOARD) #define ENABLE_SPI3 #define SD_SS_PIN -1 @@ -248,31 +272,49 @@ #define SD_SCK_PIN PC10 #define SD_MISO_PIN PC11 #define SD_MOSI_PIN PC12 - #define SD_DETECT_PIN PC4 -// -// LCD SD -// + #define SD_DETECT_PIN PC4 // SD_DETECT_PIN doesn't work with NO_SD_HOST_DRIVE disabled #elif SD_CONNECTION_IS(LCD) #define ENABLE_SPI1 - #define SDSS PA4 - #define SD_SCK_PIN PA5 - #define SD_MISO_PIN PA6 - #define SD_MOSI_PIN PA7 - #define SD_DETECT_PIN PB11 + #define SDSS EXP2_07_PIN + #define SD_SCK_PIN EXP2_09_PIN + #define SD_MISO_PIN EXP2_10_PIN + #define SD_MOSI_PIN EXP2_05_PIN + #define SD_DETECT_PIN EXP2_04_PIN #endif -/** - * _____ _____ - * (BEEPER)PB2 | · · | PE10(BTN_ENC) (SPI1 MISO) PA6 | · · | PA5 (SPI1 SCK) - * (LCD_EN)PE11 | · · | PD10(LCD_RS) (BTN_EN1) PE9 | · · | PA4 (SPI1 CS) - * (LCD_D4)PD9 | · · PD8(LCD_D5) (BTN_EN2) PE8 | · · PA7 (SPI1 MOSI) - * (LCD_D6)PE15 | · · | PE7(LCD_D7) (SPI1_RS) PB11 | · · | RESET - * GND | · · | 5V GND | · · | 3.3V - * ￣￣￣ ￣￣￣ - * EXP1 EXP2 - */ - #if ANY(TFT_COLOR_UI, TFT_CLASSIC_UI) + #define TFT_CS_PIN EXP1_04_PIN + #define TFT_SCK_PIN EXP2_09_PIN + #define TFT_MISO_PIN EXP2_10_PIN + #define TFT_MOSI_PIN EXP2_05_PIN + #define TFT_DC_PIN EXP1_03_PIN + #define TFT_RST_PIN EXP1_07_PIN + #define TFT_A0_PIN TFT_DC_PIN + + #define TFT_RESET_PIN EXP1_07_PIN + #define TFT_BACKLIGHT_PIN EXP1_08_PIN + + #define TOUCH_BUTTONS_HW_SPI + #define TOUCH_BUTTONS_HW_SPI_DEVICE 1 + + #define LCD_BACKLIGHT_PIN EXP1_08_PIN + #ifndef TFT_WIDTH + #define TFT_WIDTH 480 + #endif + #ifndef TFT_HEIGHT + #define TFT_HEIGHT 320 + #endif + + #define TOUCH_CS_PIN EXP1_06_PIN // SPI1_NSS + #define TOUCH_SCK_PIN EXP2_09_PIN // SPI1_SCK + #define TOUCH_MISO_PIN EXP2_10_PIN // SPI1_MISO + #define TOUCH_MOSI_PIN EXP2_05_PIN // SPI1_MOSI + + #define LCD_READ_ID 0xD3 + #define LCD_USE_DMA_SPI + + #define TFT_BUFFER_SIZE 14400 + #ifndef TOUCH_CALIBRATION_X #define TOUCH_CALIBRATION_X -17253 #endif @@ -289,51 +331,10 @@ #define TOUCH_ORIENTATION TOUCH_LANDSCAPE #endif - #define TFT_CS_PIN PE15 - #define TFT_SCK_PIN PA5 - #define TFT_MISO_PIN PA6 - #define TFT_MOSI_PIN PA7 - #define TFT_DC_PIN PE7 - #define TFT_RST_PIN PD10 - #define TFT_A0_PIN TFT_DC_PIN - - #define TFT_RESET_PIN PD10 - #define TFT_BACKLIGHT_PIN PE11 - - #define TOUCH_BUTTONS_HW_SPI - #define TOUCH_BUTTONS_HW_SPI_DEVICE 1 - - #define LCD_BACKLIGHT_PIN PE11 - #ifndef TFT_WIDTH - #define TFT_WIDTH 480 - #endif - #ifndef TFT_HEIGHT - #define TFT_HEIGHT 320 - #endif - - #define TOUCH_CS_PIN PD9 // SPI1_NSS - #define TOUCH_SCK_PIN PA5 // SPI1_SCK - #define TOUCH_MISO_PIN PA6 // SPI1_MISO - #define TOUCH_MOSI_PIN PA7 // SPI1_MOSI - - #define BTN_EN1 PE9 - #define BTN_EN2 PE8 - #define BEEPER_PIN PB2 - #define BTN_ENC PE10 - - #define LCD_READ_ID 0xD3 - #define LCD_USE_DMA_SPI - - #define TFT_BUFFER_SIZE 14400 - #elif HAS_WIRED_LCD - #define BEEPER_PIN PB2 - #define BTN_ENC PE10 - #define LCD_PINS_ENABLE PE11 - #define LCD_PINS_RS PD10 - #define BTN_EN1 PE9 - #define BTN_EN2 PE8 + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_RS EXP1_07_PIN #define LCD_BACKLIGHT_PIN -1 // MKS MINI12864 and MKS LCD12864B; If using MKS LCD12864A (Need to remove RPK2 resistor) @@ -341,19 +342,19 @@ //#define LCD_BACKLIGHT_PIN -1 //#define LCD_RESET_PIN -1 #define DOGLCD_A0 PD11 - #define DOGLCD_CS PE15 - //#define DOGLCD_SCK PA5 - //#define DOGLCD_MOSI PA7 + #define DOGLCD_CS EXP1_04_PIN + //#define DOGLCD_SCK EXP2_09_PIN + //#define DOGLCD_MOSI EXP2_05_PIN #elif ENABLED(MKS_MINI_12864_V3) - #define DOGLCD_CS PE11 - #define DOGLCD_A0 PD10 + #define DOGLCD_CS EXP1_08_PIN + #define DOGLCD_A0 EXP1_07_PIN #define LCD_PINS_DC DOGLCD_A0 #define LCD_BACKLIGHT_PIN -1 - #define LCD_RESET_PIN PD9 - #define NEOPIXEL_PIN PD8 - #define DOGLCD_MOSI PA7 - #define DOGLCD_SCK PA5 + #define LCD_RESET_PIN EXP1_06_PIN + #define NEOPIXEL_PIN EXP1_05_PIN + #define DOGLCD_MOSI EXP2_05_PIN + #define DOGLCD_SCK EXP2_09_PIN #if SD_CONNECTION_IS(ONBOARD) #define FORCE_SOFT_SPI #endif @@ -361,17 +362,24 @@ #else - #define LCD_PINS_D4 PD9 + #define LCD_PINS_D4 EXP1_06_PIN #if ENABLED(ULTIPANEL) - #define LCD_PINS_D5 PD8 - #define LCD_PINS_D6 PE15 - #define LCD_PINS_D7 PE7 + #define LCD_PINS_D5 EXP1_05_PIN + #define LCD_PINS_D6 EXP1_04_PIN + #define LCD_PINS_D7 EXP1_03_PIN #endif #define BOARD_ST7920_DELAY_1 DELAY_NS(96) #define BOARD_ST7920_DELAY_2 DELAY_NS(48) - #define BOARD_ST7920_DELAY_3 DELAY_NS(600) + #define BOARD_ST7920_DELAY_3 DELAY_NS(600) #endif // !MKS_MINI_12864 #endif // HAS_WIRED_LCD + +#if ANY(TFT_COLOR_UI, TFT_CLASSIC_UI, HAS_WIRED_LCD) + #define BEEPER_PIN EXP1_10_PIN + #define BTN_EN1 EXP2_08_PIN + #define BTN_EN2 EXP2_06_PIN + #define BTN_ENC EXP1_09_PIN +#endif diff --git a/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_NANO_V3.h b/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_NANO_V3.h index a51a18362f..f8d93b5604 100644 --- a/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_NANO_V3.h +++ b/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_NANO_V3.h @@ -41,10 +41,12 @@ // Use one of these or SDCard-based Emulation will be used //#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation //#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation -#define I2C_EEPROM -#define MARLIN_EEPROM_SIZE 0x1000 // 4KB -#define I2C_SCL_PIN PB6 -#define I2C_SDA_PIN PB7 +#if EITHER(NO_EEPROM_SELECTED, I2C_EEPROM) + #define I2C_EEPROM + #define MARLIN_EEPROM_SIZE 0x1000 // 4KB + #define I2C_SCL_PIN PB6 + #define I2C_SDA_PIN PB7 +#endif // // Release PB4 (Z_DIR_PIN) from JTAG NRST role @@ -253,25 +255,11 @@ #define SD_DETECT_PIN PD12 #endif -// -// LCD SD -// -#if SD_CONNECTION_IS(LCD) - #define ENABLE_SPI1 - #define SDSS PE10 - #define SD_SCK_PIN PA5 - #define SD_MISO_PIN PA6 - #define SD_MOSI_PIN PA7 - #define SD_DETECT_PIN PE12 -#endif - -// -// LCD / Controller #define SPI_FLASH -#define HAS_SPI_FLASH 1 -#define SPI_DEVICE 2 -#define SPI_FLASH_SIZE 0x1000000 #if ENABLED(SPI_FLASH) + #define HAS_SPI_FLASH 1 + #define SPI_DEVICE 2 + #define SPI_FLASH_SIZE 0x1000000 #define SPI_FLASH_CS_PIN PB12 #define SPI_FLASH_MOSI_PIN PC3 #define SPI_FLASH_MISO_PIN PC2 @@ -279,17 +267,82 @@ #endif /** - * _____ _____ - * (BEEPER)PC5 | · · | PE13(BTN_ENC) (SPI1 MISO) PA6 | · · | PA5 (SPI1 SCK) - * (LCD_EN)PD13 | · · | PC6(LCD_RS) (BTN_EN1) PE8 | · · | PE10 (SPI1 CS) - * (LCD_D4)PE14 | · · PE15(LCD_D5) (BTN_EN2) PE11 | · · PA7 (SPI1 MOSI) - * (LCD_D6)PD11 | · · | PD10(LCD_D7) (SPI1_RS) PE12 | · · | RESET - * GND | · · | 5V GND | · · | 3.3V - * ￣￣￣ ￣￣￣ - * EXP1 EXP2 + * ------ ------ + * (BEEPER) PC5 |10 9 | PE13 (BTN_ENC) (SPI1 MISO) PA6 |10 9 | PA5 (SPI1 SCK) + * (LCD_EN) PD13 | 8 7 | PC6 (LCD_RS) (BTN_EN1) PE8 | 8 7 | PE10 (SPI1 CS) + * (LCD_D4) PE14 6 5 | PE15 (LCD_D5) (BTN_EN2) PE11 6 5 | PA7 (SPI1 MOSI) + * (LCD_D6) PD11 | 4 3 | PD10 (LCD_D7) (SPI1_RS) PE12 | 4 3 | RESET + * GND | 2 1 | 5V GND | 2 1 | 3.3V + * ------ ------ + * EXP1 EXP2 */ +#define EXP1_03_PIN PD10 +#define EXP1_04_PIN PD11 +#define EXP1_05_PIN PE15 +#define EXP1_06_PIN PE14 +#define EXP1_07_PIN PC6 +#define EXP1_08_PIN PD13 +#define EXP1_09_PIN PE13 +#define EXP1_10_PIN PC5 + +#define EXP2_03_PIN -1 // RESET +#define EXP2_04_PIN PE12 +#define EXP2_05_PIN PA7 +#define EXP2_06_PIN PE11 +#define EXP2_07_PIN PE10 +#define EXP2_08_PIN PE8 +#define EXP2_09_PIN PA5 +#define EXP2_10_PIN PA6 + +// +// SPI SD Card +// +#if SD_CONNECTION_IS(LCD) + #define ENABLE_SPI1 + #define SDSS EXP2_07_PIN + #define SD_SCK_PIN EXP2_09_PIN + #define SD_MISO_PIN EXP2_10_PIN + #define SD_MOSI_PIN EXP2_05_PIN + #define SD_DETECT_PIN EXP2_04_PIN +#endif + +// +// LCD / Controller +// #if ANY(TFT_COLOR_UI, TFT_LVGL_UI, TFT_CLASSIC_UI) + #define TFT_CS_PIN EXP1_04_PIN + #define TFT_SCK_PIN EXP2_09_PIN + #define TFT_MISO_PIN EXP2_10_PIN + #define TFT_MOSI_PIN EXP2_05_PIN + #define TFT_DC_PIN EXP1_03_PIN + #define TFT_RST_PIN EXP1_07_PIN + #define TFT_A0_PIN TFT_DC_PIN + + #define TFT_RESET_PIN EXP1_07_PIN + #define TFT_BACKLIGHT_PIN EXP1_08_PIN + + #define TOUCH_BUTTONS_HW_SPI + #define TOUCH_BUTTONS_HW_SPI_DEVICE 1 + + #define LCD_BACKLIGHT_PIN EXP1_08_PIN + #ifndef TFT_WIDTH + #define TFT_WIDTH 480 + #endif + #ifndef TFT_HEIGHT + #define TFT_HEIGHT 320 + #endif + + #define TOUCH_CS_PIN EXP1_06_PIN // SPI1_NSS + #define TOUCH_SCK_PIN EXP2_09_PIN // SPI1_SCK + #define TOUCH_MISO_PIN EXP2_10_PIN // SPI1_MISO + #define TOUCH_MOSI_PIN EXP2_05_PIN // SPI1_MOSI + + #define LCD_READ_ID 0xD3 + #define LCD_USE_DMA_SPI + + #define TFT_BUFFER_SIZE 14400 + #ifndef TOUCH_CALIBRATION_X #define TOUCH_CALIBRATION_X -17253 #endif @@ -306,61 +359,20 @@ #define TOUCH_ORIENTATION TOUCH_LANDSCAPE #endif - #define TFT_CS_PIN PD11 - #define TFT_SCK_PIN PA5 - #define TFT_MISO_PIN PA6 - #define TFT_MOSI_PIN PA7 - #define TFT_DC_PIN PD10 - #define TFT_RST_PIN PC6 - #define TFT_A0_PIN TFT_DC_PIN - - #define TFT_RESET_PIN PC6 - #define TFT_BACKLIGHT_PIN PD13 - - #define TOUCH_BUTTONS_HW_SPI - #define TOUCH_BUTTONS_HW_SPI_DEVICE 1 - - #define LCD_BACKLIGHT_PIN PD13 - #ifndef TFT_WIDTH - #define TFT_WIDTH 480 - #endif - #ifndef TFT_HEIGHT - #define TFT_HEIGHT 320 - #endif - - #define TOUCH_CS_PIN PE14 // SPI1_NSS - #define TOUCH_SCK_PIN PA5 // SPI1_SCK - #define TOUCH_MISO_PIN PA6 // SPI1_MISO - #define TOUCH_MOSI_PIN PA7 // SPI1_MOSI - - #define BTN_EN1 PE8 - #define BTN_EN2 PE11 - #define BEEPER_PIN PC5 - #define BTN_ENC PE13 - - #define LCD_READ_ID 0xD3 - #define LCD_USE_DMA_SPI - - #define TFT_BUFFER_SIZE 14400 - #elif HAS_WIRED_LCD - #define BEEPER_PIN PC5 - #define BTN_ENC PE13 - #define LCD_PINS_ENABLE PD13 - #define LCD_PINS_RS PC6 - #define BTN_EN1 PE8 - #define BTN_EN2 PE11 + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_RS EXP1_07_PIN #define LCD_BACKLIGHT_PIN -1 // MKS MINI12864 and MKS LCD12864B; If using MKS LCD12864A (Need to remove RPK2 resistor) #if ENABLED(MKS_MINI_12864) //#define LCD_BACKLIGHT_PIN -1 //#define LCD_RESET_PIN -1 - #define DOGLCD_A0 PD11 - #define DOGLCD_CS PE15 - //#define DOGLCD_SCK PA5 - //#define DOGLCD_MOSI PA7 + #define DOGLCD_A0 EXP1_04_PIN + #define DOGLCD_CS EXP1_05_PIN + //#define DOGLCD_SCK EXP2_09_PIN + //#define DOGLCD_MOSI EXP2_05_PIN // Required for MKS_MINI_12864 with this board //#define MKS_LCD12864B @@ -380,32 +392,39 @@ #endif #elif ENABLED(MKS_MINI_12864_V3) - #define DOGLCD_CS PD13 - #define DOGLCD_A0 PC6 + #define DOGLCD_CS EXP1_08_PIN + #define DOGLCD_A0 EXP1_07_PIN #define LCD_PINS_DC DOGLCD_A0 #define LCD_BACKLIGHT_PIN -1 - #define LCD_RESET_PIN PE14 - #define NEOPIXEL_PIN PE15 - #define DOGLCD_MOSI PA7 - #define DOGLCD_SCK PA5 + #define LCD_RESET_PIN EXP1_06_PIN + #define NEOPIXEL_PIN EXP1_05_PIN + #define DOGLCD_MOSI EXP2_05_PIN + #define DOGLCD_SCK EXP2_09_PIN #if SD_CONNECTION_IS(ONBOARD) #define FORCE_SOFT_SPI #endif //#define LCD_SCREEN_ROT_180 - #else // !MKS_MINI_12864 + #else // !MKS_MINI_12864 - #define LCD_PINS_D4 PE14 + #define LCD_PINS_D4 EXP1_06_PIN #if ENABLED(ULTIPANEL) - #define LCD_PINS_D5 PE15 - #define LCD_PINS_D6 PD11 - #define LCD_PINS_D7 PD10 + #define LCD_PINS_D5 EXP1_05_PIN + #define LCD_PINS_D6 EXP1_04_PIN + #define LCD_PINS_D7 EXP1_03_PIN #endif #define BOARD_ST7920_DELAY_1 DELAY_NS(96) #define BOARD_ST7920_DELAY_2 DELAY_NS(48) - #define BOARD_ST7920_DELAY_3 DELAY_NS(600) + #define BOARD_ST7920_DELAY_3 DELAY_NS(600) #endif // !MKS_MINI_12864 #endif // HAS_WIRED_LCD + +#if ANY(TFT_COLOR_UI, TFT_LVGL_UI, TFT_CLASSIC_UI, HAS_WIRED_LCD) + #define BEEPER_PIN EXP1_10_PIN + #define BTN_EN1 EXP2_08_PIN + #define BTN_EN2 EXP2_06_PIN + #define BTN_ENC EXP1_09_PIN +#endif diff --git a/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_PRO_V2.h b/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_PRO_V2.h index a56889fc7e..88e2d1804e 100644 --- a/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_PRO_V2.h +++ b/Marlin/src/pins/stm32f4/pins_MKS_ROBIN_PRO_V2.h @@ -258,13 +258,13 @@ #endif /** - * _____ _____ + * ----- ----- * (BEEPER)PC5 | · · | PE13(BTN_ENC) (SPI1 MISO) PA6 | · · | PA5 (SPI1 SCK) * (LCD_EN)PD13 | · · | PC6(LCD_RS) (BTN_EN1) PE8 | · · | PE10 (SPI1 CS) * (LCD_D4)PE14 | · · | PE15(LCD_D5) (BTN_EN2) PE11 | · · | PA7 (SPI1 MOSI) * (LCD_D6)PD11 | · · | PD10(LCD_D7) (SPI DET) PE12 | · · | RESET * GND | · · | 5V GND | · · | 3.3V - * ￣￣￣ ￣￣￣ + * ----- ----- * EXP1 EXP2 */ @@ -355,15 +355,9 @@ #define LCD_PINS_D7 PD10 #endif - #ifndef ST7920_DELAY_1 - #define ST7920_DELAY_1 DELAY_NS(96) - #endif - #ifndef ST7920_DELAY_2 - #define ST7920_DELAY_2 DELAY_NS(48) - #endif - #ifndef ST7920_DELAY_3 - #define ST7920_DELAY_3 DELAY_NS(600) - #endif + #define BOARD_ST7920_DELAY_1 DELAY_NS(96) + #define BOARD_ST7920_DELAY_2 DELAY_NS(48) + #define BOARD_ST7920_DELAY_3 DELAY_NS(600) #endif // !MKS_MINI_12864