Update Delta example files

Signed-off-by: Joseivaldo Benito Junior <jrbenito@benito.qsl.br>

Marlin/example_configurations/delta/Configuration_adv.h

@@ -40,6 +40,10 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
+//Show Temperature ADC value
+//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+//#define SHOW_TEMP_ADC_VALUES
+
 //  extruder run-out prevention. 
 //if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
 //#define EXTRUDER_RUNOUT_PREVENT  
@@ -146,6 +150,21 @@
   #define EXTRUDERS 1
 #endif
 
+// Same again but for Y Axis.
+//#define Y_DUAL_STEPPER_DRIVERS
+
+// Define if the two Y drives need to rotate in opposite directions
+#define INVERT_Y2_VS_Y_DIR true
+
+#ifdef Y_DUAL_STEPPER_DRIVERS
+  #undef EXTRUDERS
+  #define EXTRUDERS 1
+#endif
+
+#if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS)
+  #error "You cannot have dual drivers for both Y and Z"
+#endif
+
 // Enable this for dual x-carriage printers. 
 // A dual x-carriage design has the advantage that the inactive extruder can be parked which
 // prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
@@ -155,8 +174,8 @@
 // Configuration for second X-carriage
 // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
 // the second x-carriage always homes to the maximum endstop.
-#define X2_MIN_POS 88     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
-#define X2_MAX_POS 350.45 // set maximum to the distance between toolheads when both heads are homed 
+#define X2_MIN_POS 80     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+#define X2_MAX_POS 353    // set maximum to the distance between toolheads when both heads are homed 
 #define X2_HOME_DIR 1     // the second X-carriage always homes to the maximum endstop position
 #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position 
     // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software 
@@ -169,14 +188,35 @@
 #define X2_STEP_PIN 25
 #define X2_DIR_PIN 23
 
-#endif // DUAL_X_CARRIAGE
+// There are a few selectable movement modes for dual x-carriages using M605 S<mode>
+//    Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
+//                           as long as it supports dual x-carriages. (M605 S0)
+//    Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
+//                           that additional slicer support is not required. (M605 S1)
+//    Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all  
+//                           actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
+//                           once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
+
+// This is the default power-up mode which can be later using M605. 
+#define DEFAULT_DUAL_X_CARRIAGE_MODE 0 
+
+// As the x-carriages are independent we can now account for any relative Z offset
+#define EXTRUDER1_Z_OFFSET 0.0           // z offset relative to extruder 0
+
+// Default settings in "Auto-park Mode" 
+#define TOOLCHANGE_PARK_ZLIFT   0.2      // the distance to raise Z axis when parking an extruder
+#define TOOLCHANGE_UNPARK_ZLIFT 1        // the distance to raise Z axis when unparking an extruder
+
+// Default x offset in duplication mode (typically set to half print bed width)
+#define DEFAULT_DUPLICATION_X_OFFSET 100
+
+#endif //DUAL_X_CARRIAGE
     
 //homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
 #define X_HOME_RETRACT_MM 5 
-#define Y_HOME_RETRACT_MM 5
+#define Y_HOME_RETRACT_MM 5 
 #define Z_HOME_RETRACT_MM 5 // deltas need the same for all three axis
 
-
 //#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 #define AXIS_RELATIVE_MODES {false, false, false, false}
@@ -238,6 +278,11 @@
 #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
 #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
 
+#define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the filesystem block order. 
+// if a file is deleted, it frees a block. hence, the order is not purely cronological. To still have auto0.g accessible, there is again the option to do that.
+// using:
+//#define MENU_ADDAUTOSTART
+
 // The hardware watchdog should reset the Microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -251,6 +296,26 @@
 // Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled.
 //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
 
+// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
+// it can e.g. be used to change z-positions in the print startup phase in realtime
+// does not respect endstops!
+//#define BABYSTEPPING
+#ifdef BABYSTEPPING
+  #define BABYSTEP_XY  //not only z, but also XY in the menu. more clutter, more functions
+  #define BABYSTEP_INVERT_Z false  //true for inverse movements in Z
+  #define BABYSTEP_Z_MULTIPLICATOR 2 //faster z movements
+  
+  #ifdef COREXY
+    #error BABYSTEPPING not implemented for COREXY yet.
+  #endif
+
+  #ifdef DELTA
+    #ifdef BABYSTEP_XY
+      #error BABYSTEPPING only implemented for Z axis on deltabots.
+    #endif
+  #endif
+#endif
+
 // extruder advance constant (s2/mm3)
 //
 // advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
@@ -302,6 +367,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #define PS_ON_ASLEEP LOW
 #endif
 
+// Control heater 0 and heater 1 in parallel.
+//#define HEATERS_PARALLEL
+
 //===========================================================================
 //=============================Buffers           ============================
 //===========================================================================
@@ -332,7 +400,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st
 
 //adds support for experimental filament exchange support M600; requires display
 #ifdef ULTIPANEL
-  //#define FILAMENTCHANGEENABLE
+  #define FILAMENTCHANGEENABLE
   #ifdef FILAMENTCHANGEENABLE
     #define FILAMENTCHANGE_XPOS 3
     #define FILAMENTCHANGE_YPOS 3
@@ -341,6 +409,12 @@ const unsigned int dropsegments=5; //everything with less than this number of st
     #define FILAMENTCHANGE_FINALRETRACT -100
   #endif
 #endif
+
+#ifdef FILAMENTCHANGEENABLE
+  #ifdef EXTRUDER_RUNOUT_PREVENT
+    #error EXTRUDER_RUNOUT_PREVENT currently incompatible with FILAMENTCHANGE
+  #endif 
+#endif
  
 //===========================================================================
 //=============================  Define Defines  ============================
@@ -349,6 +423,10 @@ const unsigned int dropsegments=5; //everything with less than this number of st
   #error "You cannot use TEMP_SENSOR_1_AS_REDUNDANT if EXTRUDERS > 1"
 #endif
 
+#if EXTRUDERS > 1 && defined HEATERS_PARALLEL
+  #error "You cannot use HEATERS_PARALLEL if EXTRUDERS > 1"
+#endif
+
 #if TEMP_SENSOR_0 > 0
   #define THERMISTORHEATER_0 TEMP_SENSOR_0
   #define HEATER_0_USES_THERMISTOR