Set more regular setup in configuration.h
This commit is contained in:
alexborro
parent
60ceca1bc1
commit
8a4b62d081
@ -59,7 +59,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_ULTIMAKER
|
||||
#define MOTHERBOARD BOARD_RAMPS_13
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
@ -123,8 +123,8 @@ Here are some standard links for getting your machine calibrated:
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 -1
|
||||
#define TEMP_SENSOR_1 -1
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
@ -301,35 +301,21 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
// The pullups are needed if you directly connect a mechanical endstop between the signal and ground pins.
|
||||
#define ENDSTOPPULLUP_XMAX
|
||||
#define ENDSTOPPULLUP_YMAX
|
||||
#define ENDSTOPPULLUP_ZMAX
|
||||
#define ENDSTOPPULLUP_XMIN
|
||||
#define ENDSTOPPULLUP_YMIN
|
||||
#define ENDSTOPPULLUP_ZMIN
|
||||
|
||||
#ifndef ENDSTOPPULLUPS
|
||||
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
||||
// #define ENDSTOPPULLUP_XMAX
|
||||
// #define ENDSTOPPULLUP_YMAX
|
||||
// #define ENDSTOPPULLUP_ZMAX
|
||||
// #define ENDSTOPPULLUP_XMIN
|
||||
// #define ENDSTOPPULLUP_YMIN
|
||||
// #define ENDSTOPPULLUP_ZMIN
|
||||
#endif
|
||||
|
||||
#ifdef ENDSTOPPULLUPS
|
||||
#define ENDSTOPPULLUP_XMAX
|
||||
#define ENDSTOPPULLUP_YMAX
|
||||
#define ENDSTOPPULLUP_ZMAX
|
||||
#define ENDSTOPPULLUP_XMIN
|
||||
#define ENDSTOPPULLUP_YMIN
|
||||
#define ENDSTOPPULLUP_ZMIN
|
||||
#endif
|
||||
|
||||
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
||||
const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
@ -346,13 +332,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define DISABLE_E false // For all extruders
|
||||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||
|
||||
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E3_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
// If you motor turns to wrong direction, you can invert it here:
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR false
|
||||
#define INVERT_Z_DIR false
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
|
||||
// ENDSTOP SETTINGS:
|
||||
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||
@ -364,9 +351,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
||||
// Travel limits after homing (units are in mm)
|
||||
#define X_MAX_POS 205
|
||||
#define X_MAX_POS 200
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MAX_POS 205
|
||||
#define Y_MAX_POS 200
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MIN_POS 0
|
||||
@ -443,7 +430,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
|
||||
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
|
||||
|
||||
#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
|
||||
// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
|
||||
//Useful to retract a deployable probe.
|
||||
|
||||
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
||||
@ -493,9 +480,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
|
||||
// default settings
|
||||
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker
|
||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker
|
||||
#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
||||
@ -539,11 +526,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
// Preheat Constants
|
||||
#define PLA_PREHEAT_HOTEND_TEMP 180
|
||||
#define PLA_PREHEAT_HPB_TEMP 70
|
||||
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
|
||||
|
||||
#define ABS_PREHEAT_HOTEND_TEMP 240
|
||||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
#define ABS_PREHEAT_HPB_TEMP 110
|
||||
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
|
||||
|
||||
//==============================LCD and SD support=============================
|
||||
|
||||
|
||||
Loading…
Reference in New Issue
Block a user