diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 7ea040803c..43ce28baaf 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1910,6 +1910,12 @@ // https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8 // //#define FYSETC_MINI_12864 +#ifdef FYSETC_MINI_12864 + #define FYSETC_MINI_12864_REV_1_2 // types C, D, E & F back light is monochrome (always on) - discrete RGB signals + //#define FYSETC_MINI_12864_REV_2_0 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - discrete RGB signals + //#define FYSETC_MINI_12864_REV_2_1 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - RGB + //#define FYSETC_MINI_12864_REV_2_1 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - Neopixel +#endif // // Factory display for Creality CR-10 diff --git a/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp b/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp index a1934886f9..5adc7fcf09 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp +++ b/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp @@ -53,7 +53,7 @@ // Public functions // -------------------------------------------------------------------------- -#if ENABLED(DUE_SOFTWARE_SPI) +#if EITHER(DUE_SOFTWARE_SPI, FORCE_SOFT_SPI) // -------------------------------------------------------------------------- // software SPI @@ -739,7 +739,42 @@ #define SPI_MODE_2_DUE_HW 0 #define SPI_MODE_3_DUE_HW 1 + /** + * The DUE SPI controller is set up so the upper word of the longword + * written to the transmit data register selects which SPI Chip Select + * Register is used. This allows different streams to have different SPI + * settings. + * + * In practice it's spooky. Some combinations hang the system, while others + * upset the peripheral device. + * + * SPI mode should be the same for all streams. The FYSETC_MINI_12864 gets + * upset if the clock phase changes after chip select goes active. + * + * SPI_CSR_CSAAT should be set for all streams. If not the WHILE_TX(0) + * macro returns immediately which can result in the SPI chip select going + * inactive before all the data has been sent. + * + * The TMC2130 library uses SPI0->SPI_CSR[3]. + * + * The U8G hardware SPI uses SPI0->SPI_CSR[0]. The system hangs and/or the + * FYSETC_MINI_12864 gets upset if lower baud rates are used and the SD card + * is inserted or removed. + * + * The SD card uses SPI0->SPI_CSR[3]. Efforts were made to use [1] and [2] + * but they all resulted in hangs or garbage on the LCD. + * + * The SPI controlled chip selects are NOT enabled in the GPIO controller. + * The application must control the chip select. + * + * All of the above can be avoided by defining FORCE_SOFT_SPI to force the + * display to use software SPI. + * + */ + void spiInit(uint8_t spiRate=6) { // Default to slowest rate if not specified) + // Also sets U8G SPI rate to 4MHz and the SPI mode to 3 + // 8.4 MHz, 4 MHz, 2 MHz, 1 MHz, 0.5 MHz, 0.329 MHz, 0.329 MHz constexpr int spiDivider[] = { 10, 21, 42, 84, 168, 255, 255 }; if (spiRate > 6) spiRate = 1; @@ -760,15 +795,16 @@ // TMC2103 compatible setup // Master mode, no fault detection, PCS bits in data written to TDR select CSR register SPI0->SPI_MR = SPI_MR_MSTR | SPI_MR_PS | SPI_MR_MODFDIS; - // SPI mode 0, 8 Bit data transfer, baud rate - SPI0->SPI_CSR[3] = SPI_CSR_SCBR(spiDivider[spiRate]) | SPI_CSR_CSAAT | SPI_MODE_0_DUE_HW; // use same CSR as TMC2130 + // SPI mode 3, 8 Bit data transfer, baud rate + SPI0->SPI_CSR[3] = SPI_CSR_SCBR(spiDivider[spiRate]) | SPI_CSR_CSAAT | SPI_MODE_3_DUE_HW; // use same CSR as TMC2130 + SPI0->SPI_CSR[0] = SPI_CSR_SCBR(spiDivider[1]) | SPI_CSR_CSAAT | SPI_MODE_3_DUE_HW; // U8G default to 4MHz } void spiBegin() { spiInit(); } static uint8_t spiTransfer(uint8_t data) { WHILE_TX(0); - SPI0->SPI_TDR = (uint32_t)data | 0x00070000UL; // Add TMC2130 PCS bits to every byte + SPI0->SPI_TDR = (uint32_t)data | 0x00070000UL; // Add TMC2130 PCS bits to every byte (use SPI0->SPI_CSR[3]) WHILE_TX(0); WHILE_RX(0); return SPI0->SPI_RDR; diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index 3013dae7a9..81c0678e3f 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -138,6 +138,8 @@ #elif ENABLED(MKS_MINI_12864) #define MINIPANEL + #define DEFAULT_LCD_CONTRAST 150 + #define LCD_CONTRAST_MAX 255 #elif ENABLED(FYSETC_MINI_12864) @@ -153,7 +155,9 @@ #if EITHER(MAKRPANEL, MINIPANEL) #define DOGLCD #define ULTIPANEL - #define DEFAULT_LCD_CONTRAST 17 + #ifndef DEFAULT_LCD_CONTRAST + #define DEFAULT_LCD_CONTRAST 17 + #endif #endif #if ENABLED(ULTI_CONTROLLER) diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index 05ff1a4ac9..d76c28bbf2 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -1786,13 +1786,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #error "Please select no more than one LCD controller option." #endif -/** - * Fysetc Mini 12864 requirements - */ -#if ENABLED(FYSETC_MINI_12864) && DISABLED(LED_USER_PRESET_STARTUP) - #error "FYSETC_MINI_12864 requires LED_USER_PRESET_STARTUP to enable the backlight on startup." -#endif - /** * Check existing CS pins against enabled TMC SPI drivers. */ diff --git a/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h b/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h index 7141eeb180..d25b58d9a4 100644 --- a/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h +++ b/Marlin/src/lcd/dogm/HAL_LCD_class_defines.h @@ -94,3 +94,16 @@ public: : U8GLIB(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset) { } }; + + +extern u8g_dev_t u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, u8g_dev_uc1701_mini12864_HAL_2x_hw_spi; + +class U8GLIB_MINI12864_2X_HAL : public U8GLIB { +public: + U8GLIB_MINI12864_2X_HAL(uint8_t sck, uint8_t mosi, uint8_t cs, uint8_t a0, uint8_t reset = U8G_PIN_NONE) + : U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset) + { } + U8GLIB_MINI12864_2X_HAL(uint8_t cs, uint8_t a0, uint8_t reset = U8G_PIN_NONE) + : U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset) + { } +}; diff --git a/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp b/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp index 35f7d4161a..4dd8759e7a 100644 --- a/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp +++ b/Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp @@ -66,42 +66,47 @@ #define PAGE_HEIGHT 8 static const uint8_t u8g_dev_uc1701_mini12864_HAL_init_seq[] PROGMEM = { - U8G_ESC_CS(0), /* disable chip */ - U8G_ESC_ADR(0), /* instruction mode */ - U8G_ESC_RST(1), /* do reset low pulse with (1*16)+2 milliseconds */ - U8G_ESC_CS(1), /* enable chip */ + U8G_ESC_CS(0), /* disable chip */ + U8G_ESC_ADR(0), /* instruction mode */ + U8G_ESC_RST(1), /* do reset low pulse with (1*16)+2 milliseconds */ + U8G_ESC_CS(1), /* enable chip */ - 0x0E2, /* soft reset */ - 0x040, /* set display start line to 0 */ - 0x0A0, /* ADC set to reverse */ - 0x0C8, /* common output mode */ - 0x0A6, /* display normal, bit val 0: LCD pixel off. */ - 0x0A2, /* LCD bias 1/9 */ - 0x02F, /* all power control circuits on */ - 0x0F8, /* set booster ratio to */ - 0x000, /* 4x */ - 0x023, /* set V0 voltage resistor ratio to large */ - 0x081, /* set contrast */ - 0x027, /* contrast value */ - 0x0AC, /* indicator */ - 0x000, /* disable */ - 0x0AF, /* display on */ + 0x0E2, /* soft reset */ + 0x040, /* set display start line to 0 */ + 0x0A0, /* ADC set to reverse */ + 0x0C8, /* common output mode */ + 0x0A6, /* display normal, bit val 0: LCD pixel off. */ + 0x0A2, /* LCD bias 1/9 */ + 0x02F, /* all power control circuits on */ + 0x0F8, /* set booster ratio to */ + 0x000, /* 4x */ + 0x023, /* set V0 voltage resistor ratio to large */ + 0x081, /* set contrast */ + 0x027, /* contrast value */ + 0x0AC, /* indicator */ + 0x000, /* disable */ + 0x0AF, /* display on */ - U8G_ESC_DLY(100), /* delay 100 ms */ - 0x0A5, /* display all points, ST7565 */ - U8G_ESC_DLY(100), /* delay 100 ms */ - U8G_ESC_DLY(100), /* delay 100 ms */ - 0x0A4, /* normal display */ - U8G_ESC_CS(0), /* disable chip */ - U8G_ESC_END /* end of sequence */ + U8G_ESC_CS(0), /* disable chip */ + U8G_ESC_DLY(100), /* delay 100 ms */ + U8G_ESC_CS(1), /* enable chip */ + + 0x0A5, /* display all points, ST7565 */ + U8G_ESC_CS(0), /* disable chip */ + U8G_ESC_DLY(100), /* delay 100 ms */ + U8G_ESC_DLY(100), /* delay 100 ms */ + U8G_ESC_CS(1), /* enable chip */ + 0x0A4, /* normal display */ + U8G_ESC_CS(0), /* disable chip */ + U8G_ESC_END /* end of sequence */ }; static const uint8_t u8g_dev_uc1701_mini12864_HAL_data_start[] PROGMEM = { - U8G_ESC_ADR(0), /* instruction mode */ - U8G_ESC_CS(1), /* enable chip */ - 0x010, /* set upper 4 bit of the col adr to 0 */ - 0x000, /* set lower 4 bit of the col adr to 4 */ - U8G_ESC_END /* end of sequence */ + U8G_ESC_ADR(0), /* instruction mode */ + U8G_ESC_CS(1), /* enable chip */ + 0x010, /* set upper 4 bit of the col adr to 0 */ + 0x000, /* set lower 4 bit of the col adr to 4 */ + U8G_ESC_END /* end of sequence */ }; uint8_t u8g_dev_uc1701_mini12864_HAL_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) { diff --git a/Marlin/src/lcd/dogm/ultralcd_DOGM.h b/Marlin/src/lcd/dogm/ultralcd_DOGM.h index 4319bd5fd6..8ce25d0e77 100644 --- a/Marlin/src/lcd/dogm/ultralcd_DOGM.h +++ b/Marlin/src/lcd/dogm/ultralcd_DOGM.h @@ -111,8 +111,8 @@ // The MINIPanel display //#define U8G_CLASS U8GLIB_MINI12864 //#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 8 stripes - #define U8G_CLASS U8GLIB_MINI12864_2X - #if ENABLED(FYSETC_MINI_12864) && DOGLCD_SCK > 0 + #define U8G_CLASS U8GLIB_MINI12864_2X_HAL + #if BOTH(FYSETC_MINI_12864, FORCE_SOFT_SPI) #define U8G_PARAM DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0 // 4 stripes SW-SPI #else #define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 4 stripes HW-SPI diff --git a/Marlin/src/lcd/ultralcd.cpp b/Marlin/src/lcd/ultralcd.cpp index cb8b308df3..cf1f8f98ea 100644 --- a/Marlin/src/lcd/ultralcd.cpp +++ b/Marlin/src/lcd/ultralcd.cpp @@ -668,6 +668,7 @@ void MarlinUI::update() { static uint16_t max_display_update_time = 0; static millis_t next_lcd_update_ms; + millis_t ms = millis(); #if HAS_LCD_MENU @@ -729,11 +730,12 @@ void MarlinUI::update() { refresh(); init_lcd(); // May revive the LCD if static electricity killed it + ms = millis(); + next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL; // delay LCD update until after SD activity completes } #endif // SDSUPPORT && SD_DETECT_PIN - const millis_t ms = millis(); if (ELAPSED(ms, next_lcd_update_ms) #if HAS_GRAPHICAL_LCD || drawing_screen diff --git a/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h b/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h index 3812195c65..319c56f31f 100644 --- a/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h +++ b/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h @@ -202,26 +202,45 @@ #define SD_DETECT_PIN P1_31 // (49) (NOT 5V tolerant) #if ENABLED(FYSETC_MINI_12864) - #define DOGLCD_CS P1_18 + #define DOGLCD_CS P1_18 #define DOGLCD_A0 P1_19 - #define LCD_RESET_PIN P1_20 + #define LCD_BACKLIGHT_PIN -1 - #define RGB_LED - #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN P1_21 - #endif - #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN P1_22 - #endif - #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN P1_23 - #endif - #ifndef RGB_LED_W_PIN - #define RGB_LED_W_PIN -1 + #define LCD_RESET_PIN P1_20 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #define RGB_LED + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN P1_21 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN P1_22 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN P1_23 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN P1_21 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" #endif - #else + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + + #else // !FYSETC_MINI_12864 #if ENABLED(MKS_MINI_12864) #define DOGLCD_CS P1_21 @@ -234,7 +253,7 @@ #define LCD_PINS_D7 P1_23 #endif - #endif // FYSETC_MINI_12864 + #endif // !FYSETC_MINI_12864 #endif diff --git a/Marlin/src/pins/pins_FYSETC_F6_13.h b/Marlin/src/pins/pins_FYSETC_F6_13.h index 84b834842c..d40abd1024 100644 --- a/Marlin/src/pins/pins_FYSETC_F6_13.h +++ b/Marlin/src/pins/pins_FYSETC_F6_13.h @@ -28,8 +28,8 @@ #error "Oops! Select 'FYSETC F6' in 'Tools > Board.'" #endif -#ifdef SD_DETECT_INVERTED - #error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board." +#if ENABLED(SD_DETECT_INVERTED) + //#error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board." #endif #define BOARD_NAME "FYSETC F6 1.3" @@ -190,20 +190,42 @@ // #define DOGLCD_A0 16 #define DOGLCD_CS 17 - #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN 25 - #endif - #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN 27 - #endif - #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN 29 - #endif #define LCD_BACKLIGHT_PIN -1 - #define LCD_RESET_PIN 23 #define KILL_PIN 41 + #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 25 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 27 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 29 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" + #endif + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + #elif HAS_GRAPHICAL_LCD #define LCD_PINS_RS 16 diff --git a/Marlin/src/pins/pins_RAMPS.h b/Marlin/src/pins/pins_RAMPS.h index 40d3dd11e2..a705e3e194 100644 --- a/Marlin/src/pins/pins_RAMPS.h +++ b/Marlin/src/pins/pins_RAMPS.h @@ -526,7 +526,6 @@ // From https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8 #define BEEPER_PIN 37 - #define LCD_RESET_PIN 23 #define DOGLCD_A0 16 #define DOGLCD_CS 17 @@ -537,14 +536,36 @@ #define SD_DETECT_PIN 49 - #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN 25 + #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 25 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 27 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 29 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" #endif - #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN 27 - #endif - #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN 29 + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" #endif #elif ENABLED(MINIPANEL) diff --git a/Marlin/src/pins/pins_RAMPS_FD_V1.h b/Marlin/src/pins/pins_RAMPS_FD_V1.h index a8bec209ef..78e75d9116 100644 --- a/Marlin/src/pins/pins_RAMPS_FD_V1.h +++ b/Marlin/src/pins/pins_RAMPS_FD_V1.h @@ -150,32 +150,71 @@ #if ENABLED(NEWPANEL) #define LCD_PINS_RS 16 #define LCD_PINS_ENABLE 17 - #define LCD_PINS_D4 23 - #define LCD_PINS_D5 25 - #define LCD_PINS_D6 27 - #define LCD_PINS_D7 29 #endif #if ENABLED(FYSETC_MINI_12864) #define DOGLCD_CS LCD_PINS_ENABLE #define DOGLCD_A0 LCD_PINS_RS - #elif ENABLED(MINIPANEL) - #define DOGLCD_CS 25 - #define DOGLCD_A0 27 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems + + #define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 25 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 27 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 29 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" + #endif + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + + #elif ENABLED(NEWPANEL) + + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 + + #if ENABLED(MINIPANEL) + #define DOGLCD_CS 25 + #define DOGLCD_A0 27 + #endif + #endif #if ANY(VIKI2, miniVIKI) - #define DOGLCD_A0 16 - #define KILL_PIN 51 - #define STAT_LED_BLUE_PIN 29 - #define STAT_LED_RED_PIN 23 - #define DOGLCD_CS 17 - #define DOGLCD_SCK 76 // SCK_PIN - These are required for DUE Hardware SPI - #define DOGLCD_MOSI 75 // MOSI_PIN - #define DOGLCD_MISO 74 // MISO_PIN + #define DOGLCD_A0 16 + #define KILL_PIN 51 + #define STAT_LED_BLUE_PIN 29 + #define STAT_LED_RED_PIN 23 + #define DOGLCD_CS 17 + #define DOGLCD_SCK 76 // SCK_PIN - Required for DUE Hardware SPI + #define DOGLCD_MOSI 75 // MOSI_PIN + #define DOGLCD_MISO 74 // MISO_PIN #endif - #endif // ULTRA_LCD #if HAS_DRIVER(TMC2208) @@ -201,10 +240,8 @@ // // M3/M4/M5 - Spindle/Laser Control // -#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA) - #if HOTENDS < 3 - #define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA - #define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM - #define SPINDLE_DIR_PIN 47 // Use E2 DIR - #endif +#if HOTENDS < 3 && ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA) + #define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA + #define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN 47 // Use E2 DIR #endif diff --git a/Marlin/src/pins/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/pins_RAMPS_RE_ARM.h index 9c7bbf4eea..5871b80d15 100644 --- a/Marlin/src/pins/pins_RAMPS_RE_ARM.h +++ b/Marlin/src/pins/pins_RAMPS_RE_ARM.h @@ -320,6 +320,7 @@ #define DOGLCD_MOSI P0_18 #define DOGLCD_CS P1_09 // use Ethernet connector for EXP1 cable signals #define DOGLCD_A0 P1_14 + #define FORCE_SOFT_SPI // required on a Re-ARM system #else #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 #define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2 diff --git a/Marlin/src/pins/pins_RURAMPS4D_11.h b/Marlin/src/pins/pins_RURAMPS4D_11.h index 517be5b9b5..718e44651e 100644 --- a/Marlin/src/pins/pins_RURAMPS4D_11.h +++ b/Marlin/src/pins/pins_RURAMPS4D_11.h @@ -202,31 +202,24 @@ // #if ENABLED(ULTRA_LCD) - #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) - + #if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BEEPER_PIN 62 + #define LCD_PINS_D4 48 + #define LCD_PINS_D5 50 + #define LCD_PINS_D6 52 + #define LCD_PINS_D7 53 + #define SD_DETECT_PIN 51 + #endif + + #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) #define LCD_PINS_RS 63 #define LCD_PINS_ENABLE 64 - #define LCD_PINS_D4 48 - #define LCD_PINS_D5 50 - #define LCD_PINS_D6 52 - #define LCD_PINS_D7 53 - - #define SD_DETECT_PIN 51 #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) - #define BEEPER_PIN 62 - #define LCD_PINS_RS 52 #define LCD_PINS_ENABLE 53 - #define LCD_PINS_D4 48 - #define LCD_PINS_D5 50 - #define LCD_PINS_D6 52 - #define LCD_PINS_D7 53 - - #define SD_DETECT_PIN 51 #elif HAS_SSD1306_OLED_I2C @@ -234,16 +227,57 @@ #define LCD_SDSS 10 #define SD_DETECT_PIN 51 + #elif ENABLED(FYSETC_MINI_12864) + + #define BEEPER_PIN 62 + #define DOGLCD_CS 64 + #define DOGLCD_A0 63 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems + + #define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #define RGB_LED + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 50 // D5 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 52 // D6 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 53 // D7 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 50 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" + #endif + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + #elif ENABLED(SPARK_FULL_GRAPHICS) //http://doku.radds.org/dokumentation/other-electronics/sparklcd/ #error "Oops! SPARK_FULL_GRAPHICS not supported with RURAMPS4D." - //#define LCD_PINS_D4 29//? - //#define LCD_PINS_ENABLE 27//? - //#define LCD_PINS_RS 25//? - //#define BTN_EN1 35//? - //#define BTN_EN2 33//? - //#define BTN_ENC 37//? + //#define LCD_PINS_D4 29 //? + //#define LCD_PINS_ENABLE 27 //? + //#define LCD_PINS_RS 25 //? + //#define BTN_EN1 35 //? + //#define BTN_EN2 33 //? + //#define BTN_ENC 37 //? #endif // SPARK_FULL_GRAPHICS diff --git a/Marlin/src/pins/pins_RURAMPS4D_13.h b/Marlin/src/pins/pins_RURAMPS4D_13.h index ab4aea0f2b..ddae87c245 100644 --- a/Marlin/src/pins/pins_RURAMPS4D_13.h +++ b/Marlin/src/pins/pins_RURAMPS4D_13.h @@ -188,31 +188,24 @@ // #if ENABLED(ULTRA_LCD) - #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) - + #if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BEEPER_PIN 62 + #define LCD_PINS_D4 48 + #define LCD_PINS_D5 50 + #define LCD_PINS_D6 52 + #define LCD_PINS_D7 53 + #define SD_DETECT_PIN 51 + #endif + + #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) #define LCD_PINS_RS 63 #define LCD_PINS_ENABLE 64 - #define LCD_PINS_D4 48 - #define LCD_PINS_D5 50 - #define LCD_PINS_D6 52 - #define LCD_PINS_D7 53 - - #define SD_DETECT_PIN 51 #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) - #define BEEPER_PIN 62 - #define LCD_PINS_RS 52 #define LCD_PINS_ENABLE 53 - #define LCD_PINS_D4 48 - #define LCD_PINS_D5 50 - #define LCD_PINS_D6 52 - #define LCD_PINS_D7 53 - - #define SD_DETECT_PIN 51 #elif HAS_SSD1306_OLED_I2C @@ -220,6 +213,47 @@ #define LCD_SDSS 10 #define SD_DETECT_PIN 51 + #elif ENABLED(FYSETC_MINI_12864) + + #define BEEPER_PIN 62 + #define DOGLCD_CS 64 + #define DOGLCD_A0 63 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems + + #define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally. + // Seems to work best if left open. + + #define FYSETC_MINI_12864_REV_1_2 + //#define FYSETC_MINI_12864_REV_2_0 + //#define FYSETC_MINI_12864_REV_2_1 + #if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0) + #define RGB_LED + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 50 // D5 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 52 // D6 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 53 // D7 + #endif + #elif defined(FYSETC_MINI_12864_REV_2_1) + #define NEOPIXEL_LED + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 50 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + #else + #error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined" + #endif + + #if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1) + #error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later" + #endif + #elif ENABLED(MKS_MINI_12864) #define ORIG_BEEPER_PIN 62