Merge pull request #7258 from thinkyhead/bf_cleanups_jbrazio
Add support for BQ heated bed kit with Hephestos 2
This commit is contained in:
Scott Lahteine
GitHub
@ -20,25 +20,24 @@
|
||||
*
|
||||
*/
|
||||
|
||||
/**
|
||||
* Configuration.h
|
||||
*
|
||||
* Basic settings such as:
|
||||
*
|
||||
* - Type of electronics
|
||||
* - Type of temperature sensor
|
||||
* - Printer geometry
|
||||
* - Endstop configuration
|
||||
* - LCD controller
|
||||
* - Extra features
|
||||
*
|
||||
* Advanced settings can be found in Configuration_adv.h
|
||||
*
|
||||
*/
|
||||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
#define CONFIGURATION_H_VERSION 010100
|
||||
|
||||
//===========================================================================
|
||||
//================================= README ==================================
|
||||
//===========================================================================
|
||||
|
||||
/**
|
||||
* BQ Hephestos 2 Configuration
|
||||
*
|
||||
* This configuration supports the standard Hephestos 2 with or without the
|
||||
* heated bed kit featured at https://store.bq.com/en/heated-bed-kit-hephestos2
|
||||
*
|
||||
* Enable the following option to activate all functionality related to the heated bed.
|
||||
*/
|
||||
//#define HEPHESTOS2_HEATED_BED_KIT
|
||||
|
||||
//===========================================================================
|
||||
//============================= Getting Started =============================
|
||||
//===========================================================================
|
||||
@ -269,7 +268,13 @@
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_4 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
|
||||
#if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
|
||||
#define TEMP_SENSOR_BED 70
|
||||
#define HEATER_BED_INVERTING true
|
||||
#else
|
||||
#define TEMP_SENSOR_BED 0
|
||||
#endif
|
||||
|
||||
// Dummy thermistor constant temperature readings, for use with 998 and 999
|
||||
#define DUMMY_THERMISTOR_998_VALUE 25
|
||||
@ -293,7 +298,7 @@
|
||||
// The minimal temperature defines the temperature below which the heater will not be enabled It is used
|
||||
// to check that the wiring to the thermistor is not broken.
|
||||
// Otherwise this would lead to the heater being powered on all the time.
|
||||
#define HEATER_0_MINTEMP 15
|
||||
#define HEATER_0_MINTEMP 5
|
||||
#define HEATER_1_MINTEMP 5
|
||||
#define HEATER_2_MINTEMP 5
|
||||
#define HEATER_3_MINTEMP 5
|
||||
@ -303,12 +308,12 @@
|
||||
// When temperature exceeds max temp, your heater will be switched off.
|
||||
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
|
||||
// You should use MINTEMP for thermistor short/failure protection.
|
||||
#define HEATER_0_MAXTEMP 250
|
||||
#define HEATER_0_MAXTEMP 275
|
||||
#define HEATER_1_MAXTEMP 275
|
||||
#define HEATER_2_MAXTEMP 275
|
||||
#define HEATER_3_MAXTEMP 275
|
||||
#define HEATER_4_MAXTEMP 275
|
||||
#define BED_MAXTEMP 150
|
||||
#define BED_MAXTEMP 110
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
@ -362,7 +367,10 @@
|
||||
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
|
||||
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
|
||||
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
|
||||
//#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
|
||||
#if ENABLED(HEPHESTOS2_HEATED_BED_KIT)
|
||||
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
|
||||
#endif
|
||||
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
@ -414,7 +422,7 @@
|
||||
*/
|
||||
|
||||
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
|
||||
//#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
|
||||
|
||||
//===========================================================================
|
||||
//============================= Mechanical Settings =========================
|
||||
@ -499,14 +507,14 @@
|
||||
* Override with M92
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 8000, 204 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 8000, 210.02 }
|
||||
|
||||
/**
|
||||
* Default Max Feed Rate (mm/s)
|
||||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 250, 250, 2, 200 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 167, 167, 3.3, 167 }
|
||||
|
||||
/**
|
||||
* Default Max Acceleration (change/s) change = mm/s
|
||||
@ -514,7 +522,7 @@
|
||||
* Override with M201
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 800, 800, 20, 1000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 100, 3000 }
|
||||
|
||||
/**
|
||||
* Default Acceleration (change/s) change = mm/s
|
||||
@ -524,8 +532,8 @@
|
||||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 800 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
|
||||
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
/**
|
||||
@ -536,8 +544,8 @@
|
||||
* When changing speed and direction, if the difference is less than the
|
||||
* value set here, it may happen instantaneously.
|
||||
*/
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_XJERK 20.0
|
||||
#define DEFAULT_YJERK 20.0
|
||||
#define DEFAULT_ZJERK 0.4
|
||||
#define DEFAULT_EJERK 1.0
|
||||
|
||||
@ -654,7 +662,7 @@
|
||||
*/
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER 34 // X offset: -left +right [of the nozzle]
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER 15 // Y offset: -front +behind [the nozzle]
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
|
||||
|
||||
// X and Y axis travel speed (mm/m) between probes
|
||||
#define XY_PROBE_SPEED 8000
|
||||
@ -690,7 +698,7 @@
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX 0
|
||||
|
||||
// Enable the M48 repeatability test to test probe accuracy
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{ 0:'Low', 1:'High' }
|
||||
@ -817,7 +825,7 @@
|
||||
*/
|
||||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
@ -839,12 +847,12 @@
|
||||
|
||||
// Set the number of grid points per dimension.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
#define GRID_MAX_POINTS_Y 4
|
||||
|
||||
// Set the boundaries for probing (where the probe can reach).
|
||||
#define LEFT_PROBE_BED_POSITION X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER
|
||||
#define LEFT_PROBE_BED_POSITION X_MIN_POS + (X_PROBE_OFFSET_FROM_EXTRUDER)
|
||||
#define RIGHT_PROBE_BED_POSITION X_MAX_POS - (X_PROBE_OFFSET_FROM_EXTRUDER)
|
||||
#define FRONT_PROBE_BED_POSITION Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER
|
||||
#define FRONT_PROBE_BED_POSITION Y_MIN_POS + (Y_PROBE_OFFSET_FROM_EXTRUDER)
|
||||
#define BACK_PROBE_BED_POSITION Y_MAX_POS - (Y_PROBE_OFFSET_FROM_EXTRUDER)
|
||||
|
||||
// The Z probe minimum outer margin (to validate G29 parameters).
|
||||
@ -1011,12 +1019,12 @@
|
||||
// @section temperature
|
||||
|
||||
// Preheat Constants
|
||||
#define PREHEAT_1_TEMP_HOTEND 210
|
||||
#define PREHEAT_1_TEMP_BED 70
|
||||
#define PREHEAT_1_TEMP_HOTEND 205
|
||||
#define PREHEAT_1_TEMP_BED 50
|
||||
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
#define PREHEAT_2_TEMP_HOTEND 240
|
||||
#define PREHEAT_2_TEMP_BED 110
|
||||
#define PREHEAT_2_TEMP_HOTEND 245
|
||||
#define PREHEAT_2_TEMP_BED 50
|
||||
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
|
||||
|
||||
/**
|
||||
|
||||
@ -161,8 +161,8 @@
|
||||
// then extrude some filament every couple of SECONDS.
|
||||
#define EXTRUDER_RUNOUT_PREVENT
|
||||
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 190
|
||||
#define EXTRUDER_RUNOUT_SECONDS 30
|
||||
#define EXTRUDER_RUNOUT_MINTEMP 170
|
||||
#define EXTRUDER_RUNOUT_SECONDS 60
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
|
||||
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
|
||||
#endif
|
||||
@ -369,7 +369,7 @@
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
|
||||
#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
|
||||
|
||||
// @section lcd
|
||||
|
||||
@ -447,7 +447,7 @@
|
||||
#define LCD_INFO_MENU
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// On the Info Screen, display XY with one decimal place when possible
|
||||
#define LCD_DECIMAL_SMALL_XY
|
||||
@ -720,7 +720,7 @@
|
||||
// enter the serial receive buffer, so they cannot be blocked.
|
||||
// Currently handles M108, M112, M410
|
||||
// Does not work on boards using AT90USB (USBCON) processors!
|
||||
//#define EMERGENCY_PARSER
|
||||
#define EMERGENCY_PARSER
|
||||
|
||||
// Bad Serial-connections can miss a received command by sending an 'ok'
|
||||
// Therefore some clients abort after 30 seconds in a timeout.
|
||||
@ -729,7 +729,7 @@
|
||||
//#define NO_TIMEOUTS 1000 // Milliseconds
|
||||
|
||||
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
//#define ADVANCED_OK
|
||||
#define ADVANCED_OK
|
||||
|
||||
// @section fwretract
|
||||
|
||||
|
||||
@ -5,11 +5,18 @@ NOTE: The look and feel of the Hephestos 2 while navigating the LCD menu will ch
|
||||
|
||||
## Changelog
|
||||
* 2016/03/01 - Initial release
|
||||
|
||||
* 2016/03/21 - Activated 4-point auto leveling by default
|
||||
Updated miscellaneous z-probe values
|
||||
|
||||
* 2016/06/21 - Disabled hot bed related options
|
||||
Activated software endstops
|
||||
SD printing now disables the heater when finished
|
||||
|
||||
* 2016/07/13 - Update the `DEFAULT_AXIS_STEPS_PER_UNIT` for the Z axis
|
||||
Increased the `DEFAULT_XYJERK`
|
||||
|
||||
* 2016/12/13 - Configuration updated.
|
||||
|
||||
* 2017/07/06 - Configuration updated to the latest Marlin version.
|
||||
Added support for the official BQ heated bed kit.
|
||||
|
||||
Reference in New Issue
Block a user