Updates for the configurator
- Sections in all `Configuration_adv.h` - Recognize JAPANESE/WESTERN/CYRILLIC options - Better capturing of comments for tooltips
This commit is contained in:
Scott Lahteine
@@ -3,6 +3,8 @@
|
||||
|
||||
#include "Conditionals.h"
|
||||
|
||||
// @section temperature
|
||||
|
||||
//===========================================================================
|
||||
//=============================Thermal Settings ============================
|
||||
//===========================================================================
|
||||
@@ -46,6 +48,8 @@
|
||||
//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
|
||||
//#define SHOW_TEMP_ADC_VALUES
|
||||
|
||||
// @section extruder
|
||||
|
||||
// extruder run-out prevention.
|
||||
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
|
||||
//#define EXTRUDER_RUNOUT_PREVENT
|
||||
@@ -55,6 +59,8 @@
|
||||
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
|
||||
#define EXTRUDER_RUNOUT_EXTRUDE 100
|
||||
|
||||
// @section temperature
|
||||
|
||||
//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
|
||||
//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
|
||||
#define TEMP_SENSOR_AD595_OFFSET 0.0
|
||||
@@ -72,6 +78,8 @@
|
||||
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
//#define FAN_KICKSTART_TIME 100
|
||||
|
||||
// @section extruder
|
||||
|
||||
// Extruder cooling fans
|
||||
// Configure fan pin outputs to automatically turn on/off when the associated
|
||||
// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
|
||||
@@ -89,8 +97,12 @@
|
||||
//=============================Mechanical Settings===========================
|
||||
//===========================================================================
|
||||
|
||||
// @section homing
|
||||
|
||||
#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
|
||||
|
||||
// @section extras
|
||||
|
||||
//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
|
||||
|
||||
// A single Z stepper driver is usually used to drive 2 stepper motors.
|
||||
@@ -174,6 +186,8 @@
|
||||
|
||||
#endif //DUAL_X_CARRIAGE
|
||||
|
||||
// @section homing
|
||||
|
||||
//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
|
||||
#define X_HOME_BUMP_MM 5
|
||||
#define Y_HOME_BUMP_MM 5
|
||||
@@ -181,8 +195,12 @@
|
||||
#define HOMING_BUMP_DIVISOR {10, 10, 20} // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
|
||||
|
||||
// @section machine
|
||||
|
||||
#define AXIS_RELATIVE_MODES {false, false, false, false}
|
||||
|
||||
// @section machine
|
||||
|
||||
//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
|
||||
#define INVERT_X_STEP_PIN false
|
||||
#define INVERT_Y_STEP_PIN false
|
||||
@@ -195,11 +213,15 @@
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
// @section lcd
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
|
||||
#define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000
|
||||
|
||||
@@ -242,6 +264,8 @@
|
||||
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
|
||||
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
|
||||
|
||||
// @section lcd
|
||||
|
||||
#ifdef SDSUPPORT
|
||||
|
||||
// If you are using a RAMPS board or cheap E-bay purchased boards that do not detect when an SD card is inserted
|
||||
@@ -274,6 +298,8 @@
|
||||
|
||||
#endif // SDSUPPORT
|
||||
|
||||
// @section more
|
||||
|
||||
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
|
||||
//#define USE_WATCHDOG
|
||||
|
||||
@@ -287,6 +313,8 @@
|
||||
// Enable the option to stop SD printing when hitting and endstops, needs to be enabled from the LCD menu when this option is enabled.
|
||||
//#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
||||
|
||||
// @section lcd
|
||||
|
||||
// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
|
||||
// it can e.g. be used to change z-positions in the print startup phase in real-time
|
||||
// does not respect endstops!
|
||||
@@ -297,12 +325,14 @@
|
||||
#define BABYSTEP_Z_MULTIPLICATOR 2 //faster z movements
|
||||
#endif
|
||||
|
||||
// @section extruder
|
||||
|
||||
// extruder advance constant (s2/mm3)
|
||||
//
|
||||
// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
|
||||
//
|
||||
// Hooke's law says: force = k * distance
|
||||
// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
// Hooke's law says: force = k * distance
|
||||
// Bernoulli's principle says: v ^ 2 / 2 + g . h + pressure / density = constant
|
||||
// so: v ^ 2 is proportional to number of steps we advance the extruder
|
||||
//#define ADVANCE
|
||||
|
||||
@@ -312,12 +342,16 @@
|
||||
#define STEPS_MM_E 836
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
|
||||
// Arc interpretation settings:
|
||||
#define MM_PER_ARC_SEGMENT 1
|
||||
#define N_ARC_CORRECTION 25
|
||||
|
||||
const unsigned int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement
|
||||
|
||||
// @section temperature
|
||||
|
||||
// Control heater 0 and heater 1 in parallel.
|
||||
//#define HEATERS_PARALLEL
|
||||
|
||||
@@ -325,6 +359,8 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
//=============================Buffers ============================
|
||||
//===========================================================================
|
||||
|
||||
// @section hidden
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
|
||||
#ifdef SDSUPPORT
|
||||
@@ -333,11 +369,13 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#endif
|
||||
|
||||
// @section more
|
||||
|
||||
//The ASCII buffer for receiving from the serial:
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 4
|
||||
|
||||
// @section fwretract
|
||||
|
||||
// Firmware based and LCD controlled retract
|
||||
// M207 and M208 can be used to define parameters for the retraction.
|
||||
@@ -374,58 +412,60 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
* you need to import the TMC26XStepper library into the arduino IDE for this
|
||||
******************************************************************************/
|
||||
|
||||
// @section tmc
|
||||
|
||||
//#define HAVE_TMCDRIVER
|
||||
#ifdef HAVE_TMCDRIVER
|
||||
|
||||
// #define X_IS_TMC
|
||||
#define X_MAX_CURRENT 1000 //in mA
|
||||
#define X_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define X2_IS_TMC
|
||||
#define X2_MAX_CURRENT 1000 //in mA
|
||||
#define X2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Y_IS_TMC
|
||||
#define Y_MAX_CURRENT 1000 //in mA
|
||||
#define Y_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Y2_IS_TMC
|
||||
#define Y2_MAX_CURRENT 1000 //in mA
|
||||
#define Y2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Z_IS_TMC
|
||||
#define Z_MAX_CURRENT 1000 //in mA
|
||||
#define Z_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Z2_IS_TMC
|
||||
#define Z2_MAX_CURRENT 1000 //in mA
|
||||
#define Z2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E0_IS_TMC
|
||||
#define E0_MAX_CURRENT 1000 //in mA
|
||||
#define E0_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E1_IS_TMC
|
||||
#define E1_MAX_CURRENT 1000 //in mA
|
||||
#define E1_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E2_IS_TMC
|
||||
#define E2_MAX_CURRENT 1000 //in mA
|
||||
#define E2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E3_IS_TMC
|
||||
#define E3_MAX_CURRENT 1000 //in mA
|
||||
#define E3_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
// #define X_IS_TMC
|
||||
#define X_MAX_CURRENT 1000 //in mA
|
||||
#define X_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define X2_IS_TMC
|
||||
#define X2_MAX_CURRENT 1000 //in mA
|
||||
#define X2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Y_IS_TMC
|
||||
#define Y_MAX_CURRENT 1000 //in mA
|
||||
#define Y_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Y2_IS_TMC
|
||||
#define Y2_MAX_CURRENT 1000 //in mA
|
||||
#define Y2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Z_IS_TMC
|
||||
#define Z_MAX_CURRENT 1000 //in mA
|
||||
#define Z_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define Z2_IS_TMC
|
||||
#define Z2_MAX_CURRENT 1000 //in mA
|
||||
#define Z2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E0_IS_TMC
|
||||
#define E0_MAX_CURRENT 1000 //in mA
|
||||
#define E0_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E1_IS_TMC
|
||||
#define E1_MAX_CURRENT 1000 //in mA
|
||||
#define E1_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E2_IS_TMC
|
||||
#define E2_MAX_CURRENT 1000 //in mA
|
||||
#define E2_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
// #define E3_IS_TMC
|
||||
#define E3_MAX_CURRENT 1000 //in mA
|
||||
#define E3_SENSE_RESISTOR 91 //in mOhms
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
|
||||
#endif
|
||||
|
||||
@@ -434,72 +474,74 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
||||
* you need to import the L6470 library into the arduino IDE for this
|
||||
******************************************************************************/
|
||||
|
||||
// @section l6470
|
||||
|
||||
//#define HAVE_L6470DRIVER
|
||||
#ifdef HAVE_L6470DRIVER
|
||||
|
||||
// #define X_IS_L6470
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
#define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define X2_IS_L6470
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
#define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Y_IS_L6470
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
#define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Y2_IS_L6470
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
#define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Z_IS_L6470
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
#define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Z2_IS_L6470
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
#define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E0_IS_L6470
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
#define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E1_IS_L6470
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
#define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E2_IS_L6470
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
#define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E3_IS_L6470
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
#define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define X_IS_L6470
|
||||
#define X_MICROSTEPS 16 //number of microsteps
|
||||
#define X_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define X_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define X2_IS_L6470
|
||||
#define X2_MICROSTEPS 16 //number of microsteps
|
||||
#define X2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define X2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Y_IS_L6470
|
||||
#define Y_MICROSTEPS 16 //number of microsteps
|
||||
#define Y_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Y_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Y2_IS_L6470
|
||||
#define Y2_MICROSTEPS 16 //number of microsteps
|
||||
#define Y2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Y2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Z_IS_L6470
|
||||
#define Z_MICROSTEPS 16 //number of microsteps
|
||||
#define Z_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Z_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define Z2_IS_L6470
|
||||
#define Z2_MICROSTEPS 16 //number of microsteps
|
||||
#define Z2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define Z2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E0_IS_L6470
|
||||
#define E0_MICROSTEPS 16 //number of microsteps
|
||||
#define E0_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E0_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E1_IS_L6470
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
#define E1_MICROSTEPS 16 //number of microsteps
|
||||
#define E1_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E1_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E2_IS_L6470
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
#define E2_MICROSTEPS 16 //number of microsteps
|
||||
#define E2_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E2_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
// #define E3_IS_L6470
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
#define E3_MICROSTEPS 16 //number of microsteps
|
||||
#define E3_K_VAL 50 // 0 - 255, Higher values, are higher power. Be carefull not to go too high
|
||||
#define E3_OVERCURRENT 2000 //maxc current in mA. If the current goes over this value, the driver will switch off
|
||||
#define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
|
||||
|
||||
#endif
|
||||
|
||||
#include "Conditionals.h"
|
||||
|
||||
Reference in New Issue
Block a user