bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

SPI and pins cleanup

Browse Source
This commit is contained in:
Scott Lahteine 2020-12-30 22:00:36 -06:00 committed by Scott Lahteine
parent cf996949fa
commit 7a748bd565
20 changed files with 130 additions and 517 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

15
Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_shared_hw_spi.cpp
View File

@ -64,12 +64,11 @@
#include "../../../MarlinCore.h" #include "../../../MarlinCore.h"
void spiBegin(); #ifndef LCD_SPI_SPEED
void spiInit(uint8_t spiRate); #define LCD_SPI_SPEED SPI_QUARTER_SPEED
void spiSend(uint8_t b); #endif
void spiSend(const uint8_t* buf, size_t n);
#include "../../shared/Marduino.h" #include "../../shared/HAL_SPI.h"
#include "../fastio.h" #include "../fastio.h"
void u8g_SetPIOutput_DUE_hw_spi(u8g_t *u8g, uint8_t pin_index) { void u8g_SetPIOutput_DUE_hw_spi(u8g_t *u8g, uint8_t pin_index) {
@ -100,11 +99,7 @@ uint8_t u8g_com_HAL_DUE_shared_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_va
spiBegin(); spiBegin();
#ifndef SPI_SPEED spiInit(LCD_SPI_SPEED);
#define SPI_SPEED SPI_FULL_SPEED // use same SPI speed as SD card
#endif
spiInit(2);
break; break;
case U8G_COM_MSG_ADDRESS: /* define cmd (arg_val = 0) or data mode (arg_val = 1) */ case U8G_COM_MSG_ADDRESS: /* define cmd (arg_val = 0) or data mode (arg_val = 1) */

3
Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_sw_spi.cpp
View File

@ -59,9 +59,6 @@
#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920) #if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920)
#undef SPI_SPEED
#define SPI_SPEED 2 // About 2 MHz
#include "u8g_com_HAL_DUE_sw_spi_shared.h" #include "u8g_com_HAL_DUE_sw_spi_shared.h"
#include "../../shared/Marduino.h" #include "../../shared/Marduino.h"

2
Marlin/src/HAL/LPC1768/tft/xpt2046.h
View File

@ -37,7 +37,7 @@
#define TOUCH_SCK_PIN SCK_PIN #define TOUCH_SCK_PIN SCK_PIN
#endif #endif
#ifndef TOUCH_CS_PIN #ifndef TOUCH_CS_PIN
#define TOUCH_CS_PIN CS_PIN #define TOUCH_CS_PIN SS_PIN
#endif #endif
#ifndef TOUCH_INT_PIN #ifndef TOUCH_INT_PIN
#define TOUCH_INT_PIN -1 #define TOUCH_INT_PIN -1

8
Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_sw_spi.cpp
View File

@ -62,9 +62,11 @@
#include <U8glib.h> #include <U8glib.h>
#include <SoftwareSPI.h> #include <SoftwareSPI.h>
#include "../../shared/Delay.h" #include "../../shared/Delay.h"
#include "../../shared/HAL_SPI.h"
#undef SPI_SPEED #ifndef LCD_SPI_SPEED
#define SPI_SPEED 3 // About 1 MHz #define LCD_SPI_SPEED SPI_EIGHTH_SPEED // About 1 MHz
#endif
static pin_t SCK_pin_ST7920_HAL, MOSI_pin_ST7920_HAL_HAL; static pin_t SCK_pin_ST7920_HAL, MOSI_pin_ST7920_HAL_HAL;
static uint8_t SPI_speed = 0; static uint8_t SPI_speed = 0;
@ -92,7 +94,7 @@ uint8_t u8g_com_HAL_LPC1768_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t ar
u8g_SetPIOutput(u8g, U8G_PI_MOSI); u8g_SetPIOutput(u8g, U8G_PI_MOSI);
u8g_Delay(5); u8g_Delay(5);
SPI_speed = swSpiInit(SPI_SPEED, SCK_pin_ST7920_HAL, MOSI_pin_ST7920_HAL_HAL); SPI_speed = swSpiInit(LCD_SPI_SPEED, SCK_pin_ST7920_HAL, MOSI_pin_ST7920_HAL_HAL);
u8g_SetPILevel(u8g, U8G_PI_CS, 0); u8g_SetPILevel(u8g, U8G_PI_CS, 0);
u8g_SetPILevel(u8g, U8G_PI_SCK, 0); u8g_SetPILevel(u8g, U8G_PI_SCK, 0);

8
Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_sw_spi.cpp
View File

@ -60,9 +60,11 @@
#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920) #if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920)
#include <SoftwareSPI.h> #include <SoftwareSPI.h>
#include "../../shared/HAL_SPI.h"
#undef SPI_SPEED #ifndef LCD_SPI_SPEED
#define SPI_SPEED 2 // About 2 MHz #define LCD_SPI_SPEED SPI_QUARTER_SPEED // About 2 MHz
#endif
#include <Arduino.h> #include <Arduino.h>
#include <algorithm> #include <algorithm>
@ -145,7 +147,7 @@ uint8_t u8g_com_HAL_LPC1768_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val,
u8g_SetPIOutput(u8g, U8G_PI_CS); u8g_SetPIOutput(u8g, U8G_PI_CS);
u8g_SetPIOutput(u8g, U8G_PI_A0); u8g_SetPIOutput(u8g, U8G_PI_A0);
if (U8G_PIN_NONE != u8g->pin_list[U8G_PI_RESET]) u8g_SetPIOutput(u8g, U8G_PI_RESET); if (U8G_PIN_NONE != u8g->pin_list[U8G_PI_RESET]) u8g_SetPIOutput(u8g, U8G_PI_RESET);
SPI_speed = swSpiInit(SPI_SPEED, u8g->pin_list[U8G_PI_SCK], u8g->pin_list[U8G_PI_MOSI]); SPI_speed = swSpiInit(LCD_SPI_SPEED, u8g->pin_list[U8G_PI_SCK], u8g->pin_list[U8G_PI_MOSI]);
u8g_SetPILevel(u8g, U8G_PI_SCK, 0); u8g_SetPILevel(u8g, U8G_PI_SCK, 0);
u8g_SetPILevel(u8g, U8G_PI_MOSI, 0); u8g_SetPILevel(u8g, U8G_PI_MOSI, 0);
break; break;

12
Marlin/src/HAL/STM32F1/dogm/u8g_com_stm32duino_swspi.cpp
View File

@ -23,12 +23,14 @@
#if BOTH(HAS_MARLINUI_U8GLIB, FORCE_SOFT_SPI) #if BOTH(HAS_MARLINUI_U8GLIB, FORCE_SOFT_SPI)
#include <U8glib.h> #include <U8glib.h>
#include "../../shared/HAL_SPI.h"
#undef SPI_SPEED #ifndef LCD_SPI_SPEED
#define SPI_SPEED 0 // Fastest #define LCD_SPI_SPEED SPI_FULL_SPEED // Fastest
//#define SPI_SPEED 2 // Slower //#define LCD_SPI_SPEED SPI_QUARTER_SPEED // Slower
#endif
static uint8_t SPI_speed = SPI_SPEED; static uint8_t SPI_speed = LCD_SPI_SPEED;
static inline uint8_t swSpiTransfer_mode_0(uint8_t b, const uint8_t spi_speed, const pin_t miso_pin=-1) { static inline uint8_t swSpiTransfer_mode_0(uint8_t b, const uint8_t spi_speed, const pin_t miso_pin=-1) {
LOOP_L_N(i, 8) { LOOP_L_N(i, 8) {
@ -104,7 +106,7 @@ static uint8_t swSpiInit(const uint8_t spi_speed) {
uint8_t u8g_com_HAL_STM32F1_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) { uint8_t u8g_com_HAL_STM32F1_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {
switch (msg) { switch (msg) {
case U8G_COM_MSG_INIT: case U8G_COM_MSG_INIT:
SPI_speed = swSpiInit(SPI_SPEED); SPI_speed = swSpiInit(LCD_SPI_SPEED);
break; break;
case U8G_COM_MSG_STOP: case U8G_COM_MSG_STOP:

2
Marlin/src/HAL/STM32F1/tft/xpt2046.h
View File

@ -37,7 +37,7 @@
#define TOUCH_SCK_PIN SCK_PIN #define TOUCH_SCK_PIN SCK_PIN
#endif #endif
#ifndef TOUCH_CS_PIN #ifndef TOUCH_CS_PIN
#define TOUCH_CS_PIN CS_PIN #define TOUCH_CS_PIN SS_PIN
#endif #endif
#ifndef TOUCH_INT_PIN #ifndef TOUCH_INT_PIN
#define TOUCH_INT_PIN -1 #define TOUCH_INT_PIN -1

2
Marlin/src/libs/L64XX/README.md
View File

@ -16,7 +16,7 @@ This software assumes that all drivers are in one SPI daisy chain.
- SDO of the last device is tied to MISO of the controller - SDO of the last device is tied to MISO of the controller
- All devices share the same `SCK` and `SS_PIN` pins. The user must supply a macro to control the `RESET_PIN`(s). - All devices share the same `SCK_PIN` and `SS_PIN` pins. The user must supply a macro to control the `RESET_PIN`(s).
- Each L6470 passes the data it saw on its SDI to its neighbor on the **NEXT** SPI cycle (8 bit delay). - Each L6470 passes the data it saw on its SDI to its neighbor on the **NEXT** SPI cycle (8 bit delay).

7
Marlin/src/pins/lpc1769/pins_FLY_CDY.h
View File

@ -33,7 +33,6 @@
// //
#define SERVO0_PIN P1_26 #define SERVO0_PIN P1_26
// //
// Limit Switches // Limit Switches
// //
@ -45,7 +44,6 @@
#define Z_MIN_PIN P1_22 // Z- #define Z_MIN_PIN P1_22 // Z-
#define Z_MAX_PIN P0_27 // Z+ #define Z_MAX_PIN P0_27 // Z+
// //
// Steppers // Steppers
// //
@ -106,7 +104,6 @@
#endif #endif
#endif #endif
#if HAS_TMC_UART #if HAS_TMC_UART
#define X_SERIAL_TX_PIN P1_04 #define X_SERIAL_TX_PIN P1_04
#define X_SERIAL_RX_PIN P1_04 #define X_SERIAL_RX_PIN P1_04
@ -130,8 +127,6 @@
#define TMC_BAUD_RATE 19200 #define TMC_BAUD_RATE 19200
#endif #endif
// //
// Temperature Sensors // Temperature Sensors
// //
@ -153,7 +148,6 @@
#define FAN1_PIN P1_21 #define FAN1_PIN P1_21
#define FAN2_PIN P1_24 #define FAN2_PIN P1_24
// //
// LCD / Controller // LCD / Controller
// //
@ -168,7 +162,6 @@
#define BTN_EN2 P0_01 #define BTN_EN2 P0_01
#define BTN_ENC P0_28 #define BTN_ENC P0_28
#ifndef SDCARD_CONNECTION #ifndef SDCARD_CONNECTION
#define SDCARD_CONNECTION ONBOARD #define SDCARD_CONNECTION ONBOARD
#endif #endif

146
Marlin/src/pins/stm32f1/pins_BEAST.h
View File

@ -123,16 +123,7 @@
#if HAS_WIRED_LCD #if HAS_WIRED_LCD
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define LCD_PINS_RS 49 // CS chip select /SS chip slave select #error "REPRAPWORLD_GRAPHICAL_LCD is not supported."
#define LCD_PINS_ENABLE 51 // SID (MOSI)
#define LCD_PINS_D4 52 // SCK (CLK) clock
#elif BOTH(IS_NEWPANEL, PANEL_ONE)
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#else #else
#define LCD_PINS_RS PB8 #define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2 #define LCD_PINS_ENABLE PD2
@ -141,144 +132,27 @@
#define LCD_PINS_D6 PB14 #define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15 #define LCD_PINS_D7 PB15
#if !IS_NEWPANEL #if !IS_NEWPANEL
#define BEEPER_PIN 33 #error "Non-NEWPANEL LCD is not supported."
// Buttons attached to a shift register
// Not wired yet
//#define SHIFT_CLK 38
//#define SHIFT_LD 42
//#define SHIFT_OUT 40
//#define SHIFT_EN 17
#endif #endif
#endif #endif
#if IS_NEWPANEL #if IS_NEWPANEL
#if IS_RRD_SC #if IS_RRD_SC
#error "RRD Smart Controller is not supported."
#define BEEPER_PIN 37
#define BTN_EN1 31
#define BTN_EN2 33
#define BTN_ENC 35
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
#define LCD_BACKLIGHT_PIN 39
#endif
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#error "REPRAPWORLD_GRAPHICAL_LCD is not supported."
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SD_DETECT_PIN 42
#elif ENABLED(LCD_I2C_PANELOLU2) #elif ENABLED(LCD_I2C_PANELOLU2)
#error "LCD_I2C_PANELOLU2 is not supported."
#define BTN_EN1 47
#define BTN_EN2 43
#define BTN_ENC 32
#define LCD_SDSS 53
#define SD_DETECT_PIN -1
#define KILL_PIN 41
#elif ENABLED(LCD_I2C_VIKI) #elif ENABLED(LCD_I2C_VIKI)
#error "LCD_I2C_VIKI is not supported."
#define BTN_EN1 22 // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_ENC -1
#define LCD_SDSS 53
#define SD_DETECT_PIN 49
#elif ANY(VIKI2, miniVIKI) #elif ANY(VIKI2, miniVIKI)
#error "VIKI2 / miniVIKI is not supported."
#define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 45
#define LCD_SCREEN_ROT_180
#define BTN_EN1 22
#define BTN_EN2 7
#define BTN_ENC 39
#define SDSS 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define KILL_PIN 31
#define STAT_LED_RED_PIN 32
#define STAT_LED_BLUE_PIN 35
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#error "ELB_FULL_GRAPHIC_CONTROLLER is not supported."
#define BTN_EN1 35
#define BTN_EN2 37
#define BTN_ENC 31
#define SD_DETECT_PIN 49
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER_PIN 23
#define DOGLCD_CS 29
#define DOGLCD_A0 27
#define LCD_BACKLIGHT_PIN 33
#elif ENABLED(MINIPANEL) #elif ENABLED(MINIPANEL)
#error "MINIPANEL is not supported."
#define BEEPER_PIN 42
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 66
#define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65
#define SDSS 53
#define KILL_PIN 64
// GLCD features
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
// The encoder and click button
#define BTN_EN1 40
#define BTN_EN2 63
#define BTN_ENC 59
// not connected to a pin
#define SD_DETECT_PIN 49
#else #else
#error "Other generic NEWPANEL LCD is not supported."
// Beeper on AUX-4
#define BEEPER_PIN 33
// Buttons directly attached to AUX-2
#if IS_RRW_KEYPAD
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SHIFT_OUT 40
#define SHIFT_CLK 44
#define SHIFT_LD 42
#elif ENABLED(PANEL_ONE)
#define BTN_EN1 59 // AUX2 PIN 3
#define BTN_EN2 63 // AUX2 PIN 4
#define BTN_ENC 49 // AUX3 PIN 7
#else
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31
#endif
#if ENABLED(G3D_PANEL)
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#else
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
#endif
#endif #endif
#endif // IS_NEWPANEL #endif // IS_NEWPANEL

2
Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h
View File

@ -188,7 +188,7 @@
* Board Display * Board Display
* _____ _____ * _____ _____
* 5V | 1 2 | GND (SPI1-MISO) MISO | 1 2 | SCK (SPI1-SCK) * 5V | 1 2 | GND (SPI1-MISO) MISO | 1 2 | SCK (SPI1-SCK)
* (FREE) PB7 | 3 4 | PB8 (LCD_CS) (PA9) GLCD_CS | 3 4 | SD_CS (PA10) * (FREE) PB7 | 3 4 | PB8 (LCD_CS) (PA9) LCD_CS | 3 4 | SD_CS (PA10)
* (FREE) PB9 | 5 6 | PA10 (SD_CS) (FREE) | 5 6 | MOSI (SPI1-MOSI) * (FREE) PB9 | 5 6 | PA10 (SD_CS) (FREE) | 5 6 | MOSI (SPI1-MOSI)
* RESET | 7 8 | PA9 (MOD_RESET) (PB5) SD_DET | 7 8 | (FREE) * RESET | 7 8 | PA9 (MOD_RESET) (PB5) SD_DET | 7 8 | (FREE)
* (BEEPER) PB6 | 9 10| PB5 (SD_DET) GND | 9 10| 5V * (BEEPER) PB6 | 9 10| PB5 (SD_DET) GND | 9 10| 5V

2
Marlin/src/pins/stm32f1/pins_FLSUN_HISPEED.h
View File

@ -62,10 +62,10 @@
// SPI // SPI
// Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface. // Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface.
// //
#define SPI_DEVICE 2
#define SCK_PIN PB13 // SPI2 #define SCK_PIN PB13 // SPI2
#define MISO_PIN PB14 // SPI2 #define MISO_PIN PB14 // SPI2
#define MOSI_PIN PB15 // SPI2 #define MOSI_PIN PB15 // SPI2
#define SPI_DEVICE 2
// SPI Flash // SPI Flash
#define HAS_SPI_FLASH 1 #define HAS_SPI_FLASH 1

145
Marlin/src/pins/stm32f1/pins_STM32F1R.h
View File

@ -100,16 +100,7 @@
#if HAS_WIRED_LCD #if HAS_WIRED_LCD
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define LCD_PINS_RS 49 // CS chip select /SS chip slave select #error "REPRAPWORLD_GRAPHICAL_LCD is not supported."
#define LCD_PINS_ENABLE 51 // SID (MOSI)
#define LCD_PINS_D4 52 // SCK (CLK) clock
#elif BOTH(IS_NEWPANEL, PANEL_ONE)
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#else #else
#define LCD_PINS_RS PB8 #define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2 #define LCD_PINS_ENABLE PD2
@ -118,146 +109,30 @@
#define LCD_PINS_D6 PB14 #define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15 #define LCD_PINS_D7 PB15
#if !IS_NEWPANEL #if !IS_NEWPANEL
#define BEEPER_PIN 33 #error "Non-NEWPANEL LCD is not supported."
// Buttons attached to a shift register
// Not wired yet
//#define SHIFT_CLK 38
//#define SHIFT_LD 42
//#define SHIFT_OUT 40
//#define SHIFT_EN 17
#endif #endif
#endif #endif
#if IS_NEWPANEL #if IS_NEWPANEL
#if IS_RRD_SC #if IS_RRD_SC
#error "RRD Smart Controller is not supported."
#define BEEPER_PIN 37
#define BTN_EN1 31
#define BTN_EN2 33
#define BTN_ENC 35
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
#define LCD_BACKLIGHT_PIN 39
#endif
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#error "REPRAPWORLD_GRAPHICAL_LCD is not supported."
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SD_DETECT_PIN 42
#elif ENABLED(LCD_I2C_PANELOLU2) #elif ENABLED(LCD_I2C_PANELOLU2)
#error "LCD_I2C_PANELOLU2 is not supported."
#define BTN_EN1 47
#define BTN_EN2 43
#define BTN_ENC 32
#define LCD_SDSS 53
#define SD_DETECT_PIN -1
#define KILL_PIN 41
#elif ENABLED(LCD_I2C_VIKI) #elif ENABLED(LCD_I2C_VIKI)
#error "LCD_I2C_VIKI is not supported."
#define BTN_EN1 22 // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_ENC -1
#define LCD_SDSS 53
#define SD_DETECT_PIN 49
#elif ANY(VIKI2, miniVIKI) #elif ANY(VIKI2, miniVIKI)
#error "VIKI2 / miniVIKI is not supported."
#define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 45
#define LCD_SCREEN_ROT_180
#define BTN_EN1 22
#define BTN_EN2 7
#define BTN_ENC 39
#define SDSS 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define KILL_PIN 31
#define STAT_LED_RED_PIN 32
#define STAT_LED_BLUE_PIN 35
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define BTN_EN1 35 #error "ELB_FULL_GRAPHIC_CONTROLLER is not supported."
#define BTN_EN2 37
#define BTN_ENC 31
#define SD_DETECT_PIN 49
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER_PIN 23
#define DOGLCD_CS 29
#define DOGLCD_A0 27
#define LCD_BACKLIGHT_PIN 33
#elif ENABLED(MINIPANEL) #elif ENABLED(MINIPANEL)
#error "MINIPANEL is not supported."
#define BEEPER_PIN 42
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 66
#define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65
#define SDSS 53
#define KILL_PIN 64
// GLCD features
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
// The encoder and click button
#define BTN_EN1 40
#define BTN_EN2 63
#define BTN_ENC 59
// not connected to a pin
#define SD_DETECT_PIN 49
#else #else
#error "Other generic NEWPANEL LCD is not supported."
// Beeper on AUX-4
#define BEEPER_PIN 33
// Buttons directly attached to AUX-2
#if IS_RRW_KEYPAD
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SHIFT_OUT 40
#define SHIFT_CLK 44
#define SHIFT_LD 42
#elif ENABLED(PANEL_ONE)
#define BTN_EN1 59 // AUX2 PIN 3
#define BTN_EN2 63 // AUX2 PIN 4
#define BTN_ENC 49 // AUX3 PIN 7
#else
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31
#endif #endif
#if ENABLED(G3D_PANEL)
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#else
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
#endif #endif
#endif
#endif // IS_NEWPANEL
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
#endif #endif

144
Marlin/src/pins/stm32f1/pins_STM3R_MINI.h
View File

@ -115,16 +115,7 @@
#if HAS_WIRED_LCD #if HAS_WIRED_LCD
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define LCD_PINS_RS 49 // CS chip select /SS chip slave select #error "REPRAPWORLD_GRAPHICAL_LCD is not supported."
#define LCD_PINS_ENABLE 51 // SID (MOSI)
#define LCD_PINS_D4 52 // SCK (CLK) clock
#elif BOTH(IS_NEWPANEL, PANEL_ONE)
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#else #else
#define LCD_PINS_RS PB8 #define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2 #define LCD_PINS_ENABLE PD2
@ -133,13 +124,7 @@
#define LCD_PINS_D6 PB14 #define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15 #define LCD_PINS_D7 PB15
#if !IS_NEWPANEL #if !IS_NEWPANEL
#define BEEPER_PIN 33 #error "Non-NEWPANEL LCD is not supported."
// Buttons attached to a shift register
// Not wired yet
//#define SHIFT_CLK 38
//#define SHIFT_LD 42
//#define SHIFT_OUT 40
//#define SHIFT_EN 17
#endif #endif
#endif #endif
@ -154,132 +139,23 @@
#elif IS_NEWPANEL #elif IS_NEWPANEL
#if IS_RRD_SC #if IS_RRD_SC
#error "RRD Smart Controller is not supported."
#define BEEPER_PIN 37
#define BTN_EN1 31
#define BTN_EN2 33
#define BTN_ENC 35
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
#define LCD_BACKLIGHT_PIN 39
#endif
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#error "REPRAPWORLD_GRAPHICAL_LCD is not supported."
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SD_DETECT_PIN 42
#elif ENABLED(LCD_I2C_PANELOLU2) #elif ENABLED(LCD_I2C_PANELOLU2)
#error "LCD_I2C_PANELOLU2 is not supported."
#define BTN_EN1 47
#define BTN_EN2 43
#define BTN_ENC 32
#define LCD_SDSS 53
#define SD_DETECT_PIN -1
#define KILL_PIN 41
#elif ENABLED(LCD_I2C_VIKI) #elif ENABLED(LCD_I2C_VIKI)
#error "LCD_I2C_VIKI is not supported."
#define BTN_EN1 22 // https://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_ENC -1
#define LCD_SDSS 53
#define SD_DETECT_PIN 49
#elif ANY(VIKI2, miniVIKI) #elif ANY(VIKI2, miniVIKI)
#error "VIKI2 / miniVIKI is not supported."
#define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 45
#define LCD_SCREEN_ROT_180
#define BTN_EN1 22
#define BTN_EN2 7
#define BTN_ENC 39
#define SDSS 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define KILL_PIN 31
#define STAT_LED_RED_PIN 32
#define STAT_LED_BLUE_PIN 35
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#error "ELB_FULL_GRAPHIC_CONTROLLER is not supported."
#define BTN_EN1 35
#define BTN_EN2 37
#define BTN_ENC 31
#define SD_DETECT_PIN 49
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER_PIN 23
#define DOGLCD_CS 29
#define DOGLCD_A0 27
#define LCD_BACKLIGHT_PIN 33
#elif ENABLED(MINIPANEL) #elif ENABLED(MINIPANEL)
#error "MINIPANEL is not supported."
#define BEEPER_PIN 42
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 66
#define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65
#define SDSS 53
#define KILL_PIN 64
// GLCD features
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
// The encoder and click button
#define BTN_EN1 40
#define BTN_EN2 63
#define BTN_ENC 59
// not connected to a pin
#define SD_DETECT_PIN 49
#else #else
#error "Other generic NEWPANEL LCD is not supported."
// Beeper on AUX-4
#define BEEPER_PIN 33
// Buttons directly attached to AUX-2
#if IS_RRW_KEYPAD
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SHIFT_OUT 40
#define SHIFT_CLK 44
#define SHIFT_LD 42
#elif ENABLED(PANEL_ONE)
#define BTN_EN1 59 // AUX2 PIN 3
#define BTN_EN2 63 // AUX2 PIN 4
#define BTN_ENC 49 // AUX3 PIN 7
#else
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31
#endif
#if ENABLED(G3D_PANEL)
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#else
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
#endif #endif
#endif #endif
#endif // IS_NEWPANEL
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD

96
Marlin/src/pins/stm32f4/pins_LERDGE_S.h
View File

@ -35,61 +35,61 @@
// //
// Servos // Servos
// //
#define SERVO0_PIN PD12 //confirmed #define SERVO0_PIN PD12
//#define SERVO1_PIN -1 //#define SERVO1_PIN -1
// //
// Limit Switches // Limit Switches
// //
#define X_MIN_PIN PG9 //confirmed #define X_MIN_PIN PG9
#define Y_MIN_PIN PG10 //confirmed #define Y_MIN_PIN PG10
#define Z_MIN_PIN PG11 //confirmed #define Z_MIN_PIN PG11
#define X_MAX_PIN PG12 //confirmed #define X_MAX_PIN PG12
#define Y_MAX_PIN PG13 //confirmed #define Y_MAX_PIN PG13
#define Z_MAX_PIN PG14 //confirmed #define Z_MAX_PIN PG14
// //
// Filament runout // Filament runout
// //
#define FIL_RUNOUT_PIN PC5 //confirmed #define FIL_RUNOUT_PIN PC5
// //
// Z Probe (when not Z_MIN_PIN) // Z Probe (when not Z_MIN_PIN)
// //
#ifndef Z_MIN_PROBE_PIN #ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN PG8 //confirmed #define Z_MIN_PROBE_PIN PG8
#endif #endif
// //
// Steppers // Steppers
// //
#define X_STEP_PIN PF7 //confirmed #define X_STEP_PIN PF7
#define X_DIR_PIN PF8 //confirmed #define X_DIR_PIN PF8
#define X_ENABLE_PIN PF6 //confirmed #define X_ENABLE_PIN PF6
#define Y_STEP_PIN PF10 //confirmed #define Y_STEP_PIN PF10
#define Y_DIR_PIN PF11 //confirmed #define Y_DIR_PIN PF11
#define Y_ENABLE_PIN PF9 //confirmed #define Y_ENABLE_PIN PF9
#define Z_STEP_PIN PF13 //confirmed #define Z_STEP_PIN PF13
#define Z_DIR_PIN PF14 //confirmed #define Z_DIR_PIN PF14
#define Z_ENABLE_PIN PF12 //confirmed #define Z_ENABLE_PIN PF12
#define E0_STEP_PIN PG0 //confirmed #define E0_STEP_PIN PG0
#define E0_DIR_PIN PG1 //confirmed #define E0_DIR_PIN PG1
#define E0_ENABLE_PIN PF15 //confirmed #define E0_ENABLE_PIN PF15
#define E1_STEP_PIN PG3 //confirmed #define E1_STEP_PIN PG3
#define E1_DIR_PIN PG4 //confirmed #define E1_DIR_PIN PG4
#define E1_ENABLE_PIN PG2 //confirmed #define E1_ENABLE_PIN PG2
// //
// Temperature Sensors // Temperature Sensors
// //
#define TEMP_0_PIN PC0 // See below for activation of thermistor readings #define TEMP_0_PIN PC0 // See below for activation of thermistor readings
#define TEMP_1_PIN PC1 // See below for activation of thermistor readings #define TEMP_1_PIN PC1 // See below for activation of thermistor readings
#define TEMP_BED_PIN PC3 //confirmed #define TEMP_BED_PIN PC3
// Lergde-S can choose thermocouple/thermistor mode in software. // Lergde-S can choose thermocouple/thermistor mode in software.
// For use with thermistors, these pins must be OUT/LOW. // For use with thermistors, these pins must be OUT/LOW.
@ -114,13 +114,13 @@
// //
// Heaters / Fans // Heaters / Fans
// //
#define HEATER_0_PIN PA0 //confirmed #define HEATER_0_PIN PA0
#define HEATER_1_PIN PA1 //confirmed #define HEATER_1_PIN PA1
#define HEATER_BED_PIN PA3 //confirmed #define HEATER_BED_PIN PA3
#define FAN_PIN PA15 // heater 0 fan 1 //confirmed #define FAN_PIN PA15 // heater 0 fan 1
#define FAN1_PIN PB10 // heater 1 fan 2 //confirmed #define FAN1_PIN PB10 // heater 1 fan 2
#define FAN2_PIN PF5 // heater 0 fan 2 and heater 1 fan 1 (two sockets, switched together) //confirmed #define FAN2_PIN PF5 // heater 0 fan 2 and heater 1 fan 1 (two sockets, switched together)
#ifndef E0_AUTO_FAN_PIN #ifndef E0_AUTO_FAN_PIN
#define E0_AUTO_FAN_PIN PF5 #define E0_AUTO_FAN_PIN PF5
@ -136,19 +136,19 @@
// LED / Lighting // LED / Lighting
// //
//Lerdge-S board has two LED connectors (this is the one on the mainboard) //Lerdge-S board has two LED connectors (this is the one on the mainboard)
#define CASE_LIGHT_PIN PC7 //confirmed #define CASE_LIGHT_PIN PC7
//on the dual extrusion addon board is a RGB connector //on the dual extrusion addon board is a RGB connector
#define RGB_LED_R_PIN PC7 // Shared with the mainboard LED light connector (CASE_LIGHT_PIN), confirmed #define RGB_LED_R_PIN PC7 // Shared with the mainboard LED light connector (CASE_LIGHT_PIN)
#define RGB_LED_G_PIN PB0 //confirmed #define RGB_LED_G_PIN PB0
#define RGB_LED_B_PIN PB1 //confirmed #define RGB_LED_B_PIN PB1
// //
// Misc. Functions // Misc. Functions
// //
#define SDSS PC11 // SD is working using SDIO, not sure if this definition is needed? #define SDSS PC11 // SD is working using SDIO, not sure if this definition is needed?
#define LED_PIN PC6 // Mainboard soldered green LED, confirmed #define LED_PIN PC6 // Mainboard soldered green LED
#define PS_ON_PIN PB2 // Board has a power module connector, confirmed #define PS_ON_PIN PB2 // Board has a power module connector
#define KILL_PIN -1 // There is no reset button on the LCD #define KILL_PIN -1 // There is no reset button on the LCD
#define POWER_LOSS_PIN -1 // PB2 could be used for this as well #define POWER_LOSS_PIN -1 // PB2 could be used for this as well
@ -158,12 +158,12 @@
#define SDIO_SUPPORT #define SDIO_SUPPORT
#define SDIO_CLOCK 4800000 #define SDIO_CLOCK 4800000
#define SCK_PIN PC12 //confirmed working #define SCK_PIN PC12
#define MISO_PIN PC8 //confirmed working #define MISO_PIN PC8
#define MOSI_PIN PD2 //confirmed working #define MOSI_PIN PD2
#define SS_PIN PC11 //confirmed working #define SS_PIN PC11
#define SD_DETECT_PIN PG15 //confirmed #define SD_DETECT_PIN PG15
// //
// Persistent Storage // Persistent Storage
@ -190,14 +190,14 @@
// //
// The LCD is initialized in FSMC mode // The LCD is initialized in FSMC mode
#define BEEPER_PIN PD13 //confirmed #define BEEPER_PIN PD13
#define BTN_EN1 PC14 //confirmed #define BTN_EN1 PC14
#define BTN_EN2 PC15 //confirmed #define BTN_EN2 PC15
#define BTN_ENC PC13 //confirmed #define BTN_ENC PC13
#define TFT_RESET_PIN PD6 //confirmed #define TFT_RESET_PIN PD6
#define TFT_BACKLIGHT_PIN PD3 //confirmed #define TFT_BACKLIGHT_PIN PD3
#define TFT_CS_PIN PD7 // TFT works #define TFT_CS_PIN PD7 // TFT works
#define TFT_RS_PIN PD11 // TFT works #define TFT_RS_PIN PD11 // TFT works

3
buildroot/share/PlatformIO/variants/CHITU_F103/board/board.h
View File

@ -69,14 +69,11 @@
#define BOARD_SPI1_MISO_PIN PA6 #define BOARD_SPI1_MISO_PIN PA6
#define BOARD_SPI1_MOSI_PIN PA7 #define BOARD_SPI1_MOSI_PIN PA7
#define BOARD_SPI2_NSS_PIN PB12 #define BOARD_SPI2_NSS_PIN PB12
#define BOARD_SPI2_SCK_PIN PB13 #define BOARD_SPI2_SCK_PIN PB13
#define BOARD_SPI2_MISO_PIN PB14 #define BOARD_SPI2_MISO_PIN PB14
#define BOARD_SPI2_MOSI_PIN PB15 #define BOARD_SPI2_MOSI_PIN PB15
#define BOARD_SPI3_NSS_PIN PA15 #define BOARD_SPI3_NSS_PIN PA15
#define BOARD_SPI3_SCK_PIN PB3 #define BOARD_SPI3_SCK_PIN PB3
#define BOARD_SPI3_MISO_PIN PB4 #define BOARD_SPI3_MISO_PIN PB4