TFT Presets, Generic options, Sanity checks (#19723)

Marlin/src/pins/sanguino/pins_ANET_10.h

@@ -151,7 +151,7 @@
 
 #if HAS_WIRED_LCD
   #define LCD_SDSS                            28
-  #if ENABLED(ADC_KEYPAD)
+  #if HAS_ADC_BUTTONS
     #define SERVO0_PIN                        27  // free for BLTouch/3D-Touch
     #define LCD_PINS_RS                       28
     #define LCD_PINS_ENABLE                   29
@@ -160,7 +160,7 @@
     #define LCD_PINS_D6                       16
     #define LCD_PINS_D7                       17
     #define ADC_KEYPAD_PIN                     1
-  #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+  #elif IS_RRD_FG_SC
     // Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics
     // display using an adapter board  // https://go.aisler.net/benlye/anet-lcd-adapter/pcb
     // See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748

Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h

@@ -136,7 +136,7 @@
   #define LCD_BACKLIGHT_PIN                   17  // LCD backlight LED
 #endif
 
-#if NONE(SPINDLE_FEATURE, LASER_FEATURE) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(ULTRA_LCD, NEWPANEL)// try to use IO Header
+#if NONE(SPINDLE_FEATURE, LASER_FEATURE) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header
   #define CASE_LIGHT_PIN                       4  // Hardware PWM  - see if IO Header is available
 #endif
 
@@ -185,7 +185,7 @@
         // with M42 instead of BEEPER_PIN.
         #define BEEPER_PIN                    27
 
-        #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
+        #if IS_RRD_FG_SC
           #ifndef BOARD_ST7920_DELAY_1
             #define BOARD_ST7920_DELAY_1 DELAY_NS(0)
           #endif
@@ -283,7 +283,7 @@
 
   #endif
 
-  #if ENABLED(NEWPANEL) && !defined(BTN_EN1)
+  #if IS_NEWPANEL && !defined(BTN_EN1)
     #define BTN_EN1                           11
     #define BTN_EN2                           10
   #endif
@@ -294,7 +294,7 @@
 // M3/M4/M5 - Spindle/Laser Control
 //
 #if HAS_CUTTER
-  #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(ULTRA_LCD, NEWPANEL)// try to use IO Header
+  #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(IS_ULTRA_LCD, IS_NEWPANEL) // try to use IO Header
 
     #define SPINDLE_LASER_ENA_PIN             10  // Pullup or pulldown!
     #define SPINDLE_LASER_PWM_PIN              4  // Hardware PWM

Marlin/src/pins/sanguino/pins_ZMIB_V2.h

@@ -225,7 +225,7 @@
 //
 // All the above are also RRDSC with rotary encoder
 //
-#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
+#if IS_RRD_SC
   #define BTN_EN1                              2
   #define BTN_EN2                             12
   #define BTN_ENC                             29