Minor fixes
This commit is contained in:
chrono
parent
c13d81ce15
commit
7540a81106
@ -59,7 +59,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_FELIX2
|
||||
#define MOTHERBOARD BOARD_ULTIMAKER
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
@ -70,7 +70,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
||||
|
||||
// This defines the number of extruders
|
||||
#define EXTRUDERS 2
|
||||
#define EXTRUDERS 1
|
||||
|
||||
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
||||
// 1 = ATX
|
||||
@ -79,7 +79,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
#define POWER_SUPPLY 1
|
||||
|
||||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
#define PS_DEFAULT_OFF
|
||||
// #define PS_DEFAULT_OFF
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
@ -123,18 +123,18 @@ Here are some standard links for getting your machine calibrated:
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 1
|
||||
#define TEMP_SENSOR_0 -1
|
||||
#define TEMP_SENSOR_1 -1
|
||||
#define TEMP_SENSOR_2 0
|
||||
#define TEMP_SENSOR_3 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
#define TEMP_SENSOR_BED 0
|
||||
|
||||
// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
|
||||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||||
|
||||
// Actual temperature must be close to target for this long before M109 returns success
|
||||
#define TEMP_RESIDENCY_TIME 15 // (seconds)
|
||||
#define TEMP_RESIDENCY_TIME 10 // (seconds)
|
||||
#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one
|
||||
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
||||
|
||||
@ -186,11 +186,21 @@ Here are some standard links for getting your machine calibrated:
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
// Felix 2.0+ electronics with v4 Hotend
|
||||
#define DEFAULT_Kp 12
|
||||
#define DEFAULT_Ki 0.84
|
||||
#define DEFAULT_Kd 85
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
// Ultimaker
|
||||
#define DEFAULT_Kp 22.2
|
||||
#define DEFAULT_Ki 1.08
|
||||
#define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
// #define DEFAULT_Kp 7.0
|
||||
// #define DEFAULT_Ki 0.1
|
||||
// #define DEFAULT_Kd 12
|
||||
|
||||
// Mendel Parts V9 on 12V
|
||||
// #define DEFAULT_Kp 63.0
|
||||
// #define DEFAULT_Ki 2.25
|
||||
// #define DEFAULT_Kd 440
|
||||
#endif // PIDTEMP
|
||||
|
||||
//===========================================================================
|
||||
@ -311,13 +321,13 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
||||
#endif
|
||||
|
||||
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
||||
const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
|
||||
const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
@ -334,7 +344,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
|
||||
|
||||
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
|
||||
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
|
||||
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
@ -351,11 +361,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
||||
// Travel limits after homing (units are in mm)
|
||||
#define X_MAX_POS 245
|
||||
#define X_MAX_POS 205
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MAX_POS 205
|
||||
#define Y_MIN_POS 0
|
||||
#define Z_MAX_POS 235
|
||||
#define Z_MAX_POS 200
|
||||
#define Z_MIN_POS 0
|
||||
|
||||
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
|
||||
@ -368,7 +378,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
//===========================================================================
|
||||
|
||||
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
|
||||
//#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
@ -500,13 +510,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
|
||||
// default settings
|
||||
|
||||
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164}
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker
|
||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec)
|
||||
#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
#define DEFAULT_ACCELERATION 1750 //1500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 5000 // X, Y, Z and E max acceleration in mm/s^2 for r retracts
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
@ -515,8 +524,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
||||
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
||||
#define DEFAULT_XYJERK 10 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 0.3 //0.4 // (mm/sec)
|
||||
#define DEFAULT_XYJERK 20.0 // (mm/sec)
|
||||
#define DEFAULT_ZJERK 0.4 // (mm/sec)
|
||||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
|
||||
@ -561,7 +570,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
//#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
//#define DISPLAY_CHARSET_HD44780_WESTERN // "ÄäÖöÜüß²³°" if you see a '~' instead of a 'arrow_right' at the right of submenuitems - this is the right one.
|
||||
|
||||
//#define ULTRA_LCD //general LCD support, also 16x2
|
||||
@ -765,7 +774,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#endif
|
||||
|
||||
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
||||
#define FAST_PWM_FAN
|
||||
//#define FAST_PWM_FAN
|
||||
|
||||
// Temperature status LEDs that display the hotend and bet temperature.
|
||||
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
||||
@ -773,7 +782,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
//#define TEMP_STAT_LEDS
|
||||
|
||||
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
||||
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
|
||||
// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
|
||||
// is too low, you should also increment SOFT_PWM_SCALE.
|
||||
//#define FAN_SOFT_PWM
|
||||
|
||||
@ -847,6 +856,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
//#define FILAMENT_LCD_DISPLAY
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
#include "Configuration_adv.h"
|
||||
#include "thermistortables.h"
|
||||
|
||||
|
||||
@ -344,7 +344,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
||||
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
|
||||
|
||||
// Travel limits after homing (units are in mm)
|
||||
#define X_MAX_POS 245
|
||||
#define X_MAX_POS 255
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MAX_POS 205
|
||||
#define Y_MIN_POS 0
|
||||
|
||||
Loading…
Reference in New Issue
Block a user