Level Corners with Probe option (#20241)

Marlin/Configuration.h

@@ -1392,6 +1392,12 @@
   #define LEVEL_CORNERS_HEIGHT      0.0   // (mm) Z height of nozzle at leveling points
   #define LEVEL_CORNERS_Z_HOP       4.0   // (mm) Z height of nozzle between leveling points
   //#define LEVEL_CENTER_TOO              // Move to the center after the last corner
+  //#define LEVEL_CORNERS_USE_PROBE
+  #if ENABLED(LEVEL_CORNERS_USE_PROBE)
+    #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
+    #define LEVEL_CORNERS_VERIFY_RAISED   // After adjustment triggers the probe, re-probe to verify
+    //#define LEVEL_CORNERS_AUDIO_FEEDBACK
+  #endif
 #endif
 
 /**

Marlin/src/feature/backlash.cpp

@@ -123,24 +123,22 @@ void Backlash::add_correction_steps(const int32_t &da, const int32_t &db, const
 }
 
 #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
-  #if HAS_CUSTOM_PROBE_PIN
+
-    #define TEST_PROBE_PIN (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
+  #include "../module/probe.h"
-  #else
-    #define TEST_PROBE_PIN (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)
-  #endif
 
   // Measure Z backlash by raising nozzle in increments until probe deactivates
   void Backlash::measure_with_probe() {
     if (measured_count.z == 255) return;
 
     const float start_height = current_position.z;
-    while (current_position.z < (start_height + BACKLASH_MEASUREMENT_LIMIT) && TEST_PROBE_PIN)
+    while (current_position.z < (start_height + BACKLASH_MEASUREMENT_LIMIT) && PROBE_TRIGGERED())
       do_blocking_move_to_z(current_position.z + BACKLASH_MEASUREMENT_RESOLUTION, MMM_TO_MMS(BACKLASH_MEASUREMENT_FEEDRATE));
 
     // The backlash from all probe points is averaged, so count the number of measurements
     measured_mm.z += current_position.z - start_height;
     measured_count.z++;
   }
+
 #endif
 
 #endif // BACKLASH_COMPENSATION

Marlin/src/feature/bltouch.cpp

@@ -31,6 +31,7 @@ BLTouch bltouch;
 bool BLTouch::last_written_mode; // Initialized by settings.load, 0 = Open Drain; 1 = 5V Drain
 
 #include "../module/servo.h"
+#include "../module/probe.h"
 
 void stop();
 
@@ -90,15 +91,7 @@ void BLTouch::clear() {
   _stow();     // STOW to be ready for meaningful work. Could fail, don't care
 }
 
-bool BLTouch::triggered() {
+bool BLTouch::triggered() { return PROBE_TRIGGERED(); }
-  return (
-    #if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
-      READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING
-    #else
-      READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING
-    #endif
-  );
-}
 
 bool BLTouch::deploy_proc() {
   // Do a DEPLOY

Marlin/src/gcode/calibrate/G425.cpp

@@ -143,14 +143,16 @@ inline void park_above_object(measurements_t &m, const float uncertainty) {
 
 #endif
 
+#if !PIN_EXISTS(CALIBRATION)
+  #include "../../module/probe.h"
+#endif
+
 inline bool read_calibration_pin() {
   return (
     #if PIN_EXISTS(CALIBRATION)
       READ(CALIBRATION_PIN) != CALIBRATION_PIN_INVERTING
-    #elif HAS_CUSTOM_PROBE_PIN
-      READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING
     #else
-      READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING
+      PROBE_TRIGGERED()
     #endif
   );
 }

Marlin/src/inc/SanityCheck.h

@@ -357,6 +357,8 @@
   #error "LEVEL_CORNERS_INSET is now LEVEL_CORNERS_INSET_LFRB."
 #elif ENABLED(LEVEL_BED_CORNERS) && !defined(LEVEL_CORNERS_INSET_LFRB)
   #error "LEVEL_BED_CORNERS requires LEVEL_CORNERS_INSET_LFRB values."
+#elif BOTH(LEVEL_CORNERS_USE_PROBE, SENSORLESS_PROBING)
+  #error "LEVEL_CORNERS_USE_PROBE is incompatible with SENSORLESS_PROBING."
 #elif defined(BEZIER_JERK_CONTROL)
   #error "BEZIER_JERK_CONTROL is now S_CURVE_ACCELERATION."
 #elif HAS_JUNCTION_DEVIATION && defined(JUNCTION_DEVIATION_FACTOR)
@@ -1603,7 +1605,7 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal
  * Allen Key
  * Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis.
  */
-#if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
+#if BOTH(Z_PROBE_ALLEN_KEY, Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) && (Z_HOME_DIR < 0)
   #error "You can't home to a Z min endstop with a Z_PROBE_ALLEN_KEY."
 #endif
 

Marlin/src/lcd/language/language_en.h

@@ -125,6 +125,8 @@ namespace Language_en {
   PROGMEM Language_Str MSG_BED_LEVELING                    = _UxGT("Bed Leveling");
   PROGMEM Language_Str MSG_LEVEL_BED                       = _UxGT("Level Bed");
   PROGMEM Language_Str MSG_LEVEL_CORNERS                   = _UxGT("Level Corners");
+  PROGMEM Language_Str MSG_LEVEL_CORNERS_RAISE             = _UxGT("Raise Bed Until Probe Triggered");
+  PROGMEM Language_Str MSG_LEVEL_CORNERS_IN_RANGE          = _UxGT("All Corners Within Tolerance. Level Bed");
   PROGMEM Language_Str MSG_NEXT_CORNER                     = _UxGT("Next Corner");
   PROGMEM Language_Str MSG_MESH_EDITOR                     = _UxGT("Mesh Editor");
   PROGMEM Language_Str MSG_EDIT_MESH                       = _UxGT("Edit Mesh");
@@ -379,6 +381,7 @@ namespace Language_en {
   PROGMEM Language_Str MSG_BUTTON_DONE                     = _UxGT("Done");
   PROGMEM Language_Str MSG_BUTTON_BACK                     = _UxGT("Back");
   PROGMEM Language_Str MSG_BUTTON_PROCEED                  = _UxGT("Proceed");
+  PROGMEM Language_Str MSG_BUTTON_SKIP                     = _UxGT("Skip");
   PROGMEM Language_Str MSG_PAUSING                         = _UxGT("Pausing...");
   PROGMEM Language_Str MSG_PAUSE_PRINT                     = _UxGT("Pause Print");
   PROGMEM Language_Str MSG_RESUME_PRINT                    = _UxGT("Resume Print");

Marlin/src/lcd/menu/menu_bed_corners.cpp

@@ -44,17 +44,143 @@
   #define LEVEL_CORNERS_HEIGHT 0.0
 #endif
 
+#if ENABLED(LEVEL_CORNERS_USE_PROBE)
+  #include "../../module/probe.h"
+  #include "../../module/endstops.h"
+  #if ENABLED(BLTOUCH)
+    #include "../../feature/bltouch.h"
+  #endif
+  #ifndef LEVEL_CORNERS_PROBE_TOLERANCE
+    #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
+  #endif
+  #if ENABLED(LEVEL_CORNERS_AUDIO_FEEDBACK)
+    #include "../../libs/buzzer.h"
+    #define PROBE_BUZZ() BUZZ(200, 600)
+  #else
+    #define PROBE_BUZZ() NOOP
+  #endif
+  static float last_z;
+  static bool corner_probing_done;
+  static bool verify_corner;
+  static int good_points;
+#endif
+
 static_assert(LEVEL_CORNERS_Z_HOP >= 0, "LEVEL_CORNERS_Z_HOP must be >= 0. Please update your configuration.");
 
+extern const char G28_STR[];
+
 #if HAS_LEVELING
   static bool leveling_was_active = false;
 #endif
 
+static int8_t bed_corner;
+
 /**
  * Level corners, starting in the front-left corner.
  */
-static int8_t bed_corner;
+#if ENABLED(LEVEL_CORNERS_USE_PROBE)
-static inline void _lcd_goto_next_corner() {
+
+  static inline void _lcd_level_bed_corners_probing() {
+    ui.goto_screen([]{ MenuItem_static::draw((LCD_HEIGHT - 1) / 2, GET_TEXT(MSG_PROBING_MESH)); });
+
+    float lfrb[4] = LEVEL_CORNERS_INSET_LFRB;
+    xy_pos_t lf { (X_MIN_BED) + lfrb[0] - probe.offset_xy.x , (Y_MIN_BED) + lfrb[1] - probe.offset_xy.y },
+             rb { (X_MAX_BED) - lfrb[2] - probe.offset_xy.x , (Y_MAX_BED) - lfrb[3] - probe.offset_xy.y };
+
+    do_blocking_move_to_z(LEVEL_CORNERS_Z_HOP - probe.offset.z);
+
+    switch (bed_corner) {
+      case 0: current_position   = lf;   break; // copy xy
+      case 1: current_position.x = rb.x; break;
+      case 2: current_position.y = rb.y; break;
+      case 3: current_position.x = lf.x; break;
+      #if ENABLED(LEVEL_CENTER_TOO)
+        case 4: current_position.set(X_CENTER - probe.offset_xy.x, Y_CENTER - probe.offset_xy.y); good_points--; break;
+      #endif
+    }
+
+    do_blocking_move_to_xy(current_position);
+
+    #if ENABLED(BLTOUCH) && DISABLED(BLTOUCH_HS_MODE)
+      bltouch.deploy(); // DEPLOY in LOW SPEED MODE on every probe action
+    #endif
+    TERN_(QUIET_PROBING, probe.set_probing_paused(true));
+
+    // Move down until the probe is triggered
+    do_blocking_move_to_z(last_z - (LEVEL_CORNERS_PROBE_TOLERANCE), manual_feedrate_mm_s.z);
+
+    // Check to see if the probe was triggered
+    bool probe_triggered = TEST(endstops.trigger_state(), TERN(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN, Z_MIN, Z_MIN_PROBE));
+    if (!probe_triggered) {
+
+      static bool wait_for_probe;
+
+      ui.goto_screen([]{
+        MenuItem_confirm::select_screen(
+          GET_TEXT(MSG_BUTTON_DONE), GET_TEXT(MSG_BUTTON_SKIP)
+          , []{ corner_probing_done = true;
+                wait_for_probe = false;
+                TERN_(HAS_LEVELING, set_bed_leveling_enabled(leveling_was_active));
+                ui.goto_previous_screen_no_defer();
+            }
+          , []{ wait_for_probe = false; }
+          , GET_TEXT(MSG_LEVEL_CORNERS_RAISE)
+          , (const char*)nullptr, PSTR("")
+        );
+      });
+      ui.set_selection(true);
+
+      wait_for_probe = true;
+      while (wait_for_probe && !probe_triggered) {
+        probe_triggered = PROBE_TRIGGERED();
+        if (probe_triggered) PROBE_BUZZ();
+        idle();
+      }
+      wait_for_probe = false;
+
+      TERN_(LEVEL_CORNERS_VERIFY_RAISED, verify_corner = true);
+    }
+
+    TERN_(QUIET_PROBING, probe.set_probing_paused(false));
+
+    #if ENABLED(BLTOUCH) && DISABLED(BLTOUCH_HS_MODE)
+      bltouch.stow();
+    #endif
+
+    if (probe_triggered) {
+      endstops.hit_on_purpose();
+      if (!WITHIN(current_position.z, last_z - (LEVEL_CORNERS_PROBE_TOLERANCE), last_z + (LEVEL_CORNERS_PROBE_TOLERANCE))) {
+        last_z = current_position.z;
+        good_points = 0;
+      }
+      if (!verify_corner) good_points++;
+    }
+
+    if (!corner_probing_done) {
+      if (!verify_corner) bed_corner++;
+      if (bed_corner > 3) bed_corner = 0;
+      verify_corner = false;
+      if (good_points < 4)
+        _lcd_level_bed_corners_probing();
+      else {
+        ui.goto_screen([]{
+          MenuItem_confirm::confirm_screen(
+            []{ ui.goto_previous_screen_no_defer();
+                queue.inject_P(TERN(HAS_LEVELING, PSTR("G28\nG29"), G28_STR));
+              }
+            , []{ ui.goto_previous_screen_no_defer(); }
+            , GET_TEXT(MSG_LEVEL_CORNERS_IN_RANGE)
+            , (const char*)nullptr, PSTR("?")
+          );
+        });
+        ui.set_selection(true);
+      }
+    }
+  }
+
+#else
+
+  static inline void _lcd_goto_next_corner() {
     constexpr float lfrb[4] = LEVEL_CORNERS_INSET_LFRB;
     constexpr xy_pos_t lf { (X_MIN_BED) + lfrb[0], (Y_MIN_BED) + lfrb[1] },
                        rb { (X_MAX_BED) - lfrb[2], (Y_MAX_BED) - lfrb[3] };
@@ -71,11 +197,18 @@ static inline void _lcd_goto_next_corner() {
     line_to_current_position(manual_feedrate_mm_s.x);
     line_to_z(LEVEL_CORNERS_HEIGHT);
     if (++bed_corner > 3 + ENABLED(LEVEL_CENTER_TOO)) bed_corner = 0;
-}
+  }
+
+#endif
 
 static inline void _lcd_level_bed_corners_homing() {
   _lcd_draw_homing();
   if (all_axes_homed()) {
+    #if ENABLED(LEVEL_CORNERS_USE_PROBE)
+      TERN_(LEVEL_CENTER_TOO, bed_corner = 4);
+      endstops.enable_z_probe(true);
+      ui.goto_screen(_lcd_level_bed_corners_probing);
+    #else
       bed_corner = 0;
       ui.goto_screen([]{
         MenuItem_confirm::select_screen(
@@ -91,6 +224,7 @@ static inline void _lcd_level_bed_corners_homing() {
       });
       ui.set_selection(true);
       _lcd_goto_next_corner();
+    #endif
   }
 }
 
@@ -107,6 +241,13 @@ void _lcd_level_bed_corners() {
     set_bed_leveling_enabled(false);
   #endif
 
+  #if ENABLED(LEVEL_CORNERS_USE_PROBE)
+    last_z = LEVEL_CORNERS_HEIGHT;
+    corner_probing_done = false;
+    verify_corner = false;
+    good_points = 0;
+  #endif
+
   ui.goto_screen(_lcd_level_bed_corners_homing);
 }
 

Marlin/src/module/endstops.cpp

@@ -48,6 +48,10 @@
   #include "../feature/joystick.h"
 #endif
 
+#if HAS_BED_PROBE
+  #include "probe.h"
+#endif
+
 Endstops endstops;
 
 // private:
@@ -455,7 +459,7 @@ void _O2 Endstops::report_states() {
     ES_REPORT(Z4_MAX);
   #endif
   #if HAS_CUSTOM_PROBE_PIN
-    print_es_state(READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING, PSTR(STR_Z_PROBE));
+    print_es_state(PROBE_TRIGGERED(), PSTR(STR_Z_PROBE));
   #endif
   #if HAS_FILAMENT_SENSOR
     #if NUM_RUNOUT_SENSORS == 1

Marlin/src/module/probe.cpp

@@ -270,13 +270,7 @@ FORCE_INLINE void probe_specific_action(const bool deploy) {
   #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
     do {
       #if ENABLED(PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED)
-        if (deploy == (
+        if (deploy == PROBE_TRIGGERED()) break;
-          #if HAS_CUSTOM_PROBE_PIN
-            READ(Z_MIN_PROBE_PIN) == Z_MIN_PROBE_ENDSTOP_INVERTING
-          #else
-            READ(Z_MIN_PIN) == Z_MIN_ENDSTOP_INVERTING
-          #endif
-        )) break;
       #endif
 
       BUZZ(100, 659);
@@ -375,23 +369,15 @@ bool Probe::set_deployed(const bool deploy) {
   const xy_pos_t old_xy = current_position;
 
   #if ENABLED(PROBE_TRIGGERED_WHEN_STOWED_TEST)
-    #if HAS_CUSTOM_PROBE_PIN
-      #define PROBE_STOWED() (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
-    #else
-      #define PROBE_STOWED() (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)
-    #endif
-  #endif
-
-  #ifdef PROBE_STOWED
 
     // Only deploy/stow if needed
-    if (PROBE_STOWED() == deploy) {
+    if (PROBE_TRIGGERED() == deploy) {
       if (!deploy) endstops.enable_z_probe(false); // Switch off triggered when stowed probes early
                                                    // otherwise an Allen-Key probe can't be stowed.
       probe_specific_action(deploy);
     }
 
-    if (PROBE_STOWED() == deploy) {                // Unchanged after deploy/stow action?
+    if (PROBE_TRIGGERED() == deploy) {             // Unchanged after deploy/stow action?
       if (IsRunning()) {
         SERIAL_ERROR_MSG("Z-Probe failed");
         LCD_ALERTMESSAGEPGM_P(PSTR("Err: ZPROBE"));

Marlin/src/module/probe.h

@@ -38,6 +38,12 @@
   };
 #endif
 
+#if HAS_CUSTOM_PROBE_PIN
+  #define PROBE_TRIGGERED() (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
+#else
+  #define PROBE_TRIGGERED() (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)
+#endif
+
 class Probe {
 public:
 

buildroot/tests/LPC1769-tests

@@ -19,6 +19,7 @@ opt_set TEMP_SENSOR_1 -1
 opt_set TEMP_SENSOR_BED 5
 opt_enable VIKI2 SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
            FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
+           LEVEL_BED_CORNERS LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \
            BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \
            PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
            Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \