Merge branch 'RCBugFix' into RC

Marlin/Conditionals.h

@@ -1,7 +1,30 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Conditionals.h
  * Defines that depend on configuration but are not editable.
  */
+
 #ifndef CONDITIONALS_H
 
 #ifndef M_PI

Marlin/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/Default_Version.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
  * This file is a placeholder for a file which could be distributed in an archive
  * It takes the place of an automatically created "_Version.h" which is generated during the build process
  */

Marlin/M100_Free_Mem_Chk.cpp

@@ -1,26 +1,45 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * M100 Free Memory Watcher
+ * 
+ * This code watches the free memory block between the bottom of the heap and the top of the stack.
+ * This memory block is initialized and watched via the M100 command.
+ * 
+ * M100 I Initializes the free memory block and prints vitals statistics about the area
+ * M100 F Identifies how much of the free memory block remains free and unused.  It also
+ *    detects and reports any corruption within the free memory block that may have
+ *    happened due to errant firmware.
+ * M100 D Does a hex display of the free memory block along with a flag for any errant
+ *    data that does not match the expected value.
+ * M100 C x Corrupts x locations within the free memory block.   This is useful to check the
+ *    correctness of the M100 F and M100 D commands.
+ * 
+ * Initial version by Roxy-3DPrintBoard
+ */
 #define M100_FREE_MEMORY_DUMPER     // Comment out to remove Dump sub-command
 #define M100_FREE_MEMORY_CORRUPTOR    // Comment out to remove Corrupt sub-command
 
-
-// M100 Free Memory Watcher
-//
-// This code watches the free memory block between the bottom of the heap and the top of the stack.
-// This memory block is initialized and watched via the M100 command.
-//
-// M100 I Initializes the free memory block and prints vitals statistics about the area
-// M100 F Identifies how much of the free memory block remains free and unused.  It also
-//    detects and reports any corruption within the free memory block that may have
-//    happened due to errant firmware.
-// M100 D Does a hex display of the free memory block along with a flag for any errant
-//    data that does not match the expected value.
-// M100 C x Corrupts x locations within the free memory block.   This is useful to check the
-//    correctness of the M100 F and M100 D commands.
-//
-// Initial version by Roxy-3DPrintBoard
-//
-//
-
-
 #include "Marlin.h"
 
 #if ENABLED(M100_FREE_MEMORY_WATCHER)

Marlin/Marlin.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 // Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
 // License: GPL
 

Marlin/Marlin.ino

@@ -1,5 +1,6 @@
 /**
- * Marlin Firmware
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
  * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
@@ -17,6 +18,9 @@
  * You should have received a copy of the GNU General Public License
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
  *
+ */
+
+/**
  * About Marlin
  *
  * This firmware is a mashup between Sprinter and grbl.

Marlin/MarlinSerial.cpp

@@ -1,21 +1,29 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   HardwareSerial.cpp - Hardware serial library for Wiring
   Copyright (c) 2006 Nicholas Zambetti.  All right reserved.
 
-  This library is free software; you can redistribute it and/or
-  modify it under the terms of the GNU Lesser General Public
-  License as published by the Free Software Foundation; either
-  version 2.1 of the License, or (at your option) any later version.
-
-  This library is distributed in the hope that it will be useful,
-  but WITHOUT ANY WARRANTY; without even the implied warranty of
-  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
-  Lesser General Public License for more details.
-
-  You should have received a copy of the GNU Lesser General Public
-  License along with this library; if not, write to the Free Software
-  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
-
   Modified 23 November 2006 by David A. Mellis
   Modified 28 September 2010 by Mark Sproul
 */

Marlin/MarlinSerial.h

@@ -1,21 +1,29 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   HardwareSerial.h - Hardware serial library for Wiring
   Copyright (c) 2006 Nicholas Zambetti.  All right reserved.
 
-  This library is free software; you can redistribute it and/or
-  modify it under the terms of the GNU Lesser General Public
-  License as published by the Free Software Foundation; either
-  version 2.1 of the License, or (at your option) any later version.
-
-  This library is distributed in the hope that it will be useful,
-  but WITHOUT ANY WARRANTY; without even the implied warranty of
-  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
-  Lesser General Public License for more details.
-
-  You should have received a copy of the GNU Lesser General Public
-  License along with this library; if not, write to the Free Software
-  Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
-
   Modified 28 September 2010 by Mark Sproul
 */
 

Marlin/Marlin_main.cpp

@@ -1,5 +1,6 @@
 /**
- * Marlin Firmware
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
  * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
@@ -16,6 +17,10 @@
  *
  * You should have received a copy of the GNU General Public License
  * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
  *
  * About Marlin
  *
@@ -3079,7 +3084,7 @@ inline void gcode_G28() {
           #if ENABLED(DELTA)
             // Avoid probing the corners (outside the round or hexagon print surface) on a delta printer.
             float distance_from_center = sqrt(xProbe * xProbe + yProbe * yProbe);
-            if (distance_from_center > DELTA_PROBABLE_RADIUS) continue;
+            if (distance_from_center > DELTA_PROBEABLE_RADIUS) continue;
           #endif //DELTA
 
           ProbeAction act;
@@ -6613,7 +6618,7 @@ void clamp_to_software_endstops(float target[3]) {
                           - sq(delta_tower3_x - cartesian[X_AXIS])
                           - sq(delta_tower3_y - cartesian[Y_AXIS])
                          ) + cartesian[Z_AXIS];
-    /*
+    /**
     SERIAL_ECHOPGM("cartesian x="); SERIAL_ECHO(cartesian[X_AXIS]);
     SERIAL_ECHOPGM(" y="); SERIAL_ECHO(cartesian[Y_AXIS]);
     SERIAL_ECHOPGM(" z="); SERIAL_ECHOLN(cartesian[Z_AXIS]);
@@ -6648,7 +6653,7 @@ void clamp_to_software_endstops(float target[3]) {
       delta[Y_AXIS] += offset;
       delta[Z_AXIS] += offset;
 
-      /*
+      /**
       SERIAL_ECHOPGM("grid_x="); SERIAL_ECHO(grid_x);
       SERIAL_ECHOPGM(" grid_y="); SERIAL_ECHO(grid_y);
       SERIAL_ECHOPGM(" floor_x="); SERIAL_ECHO(floor_x);
@@ -7140,7 +7145,7 @@ void plan_arc(
     delta[Y_AXIS] = (SCARA_theta + SCARA_psi) * SCARA_RAD2DEG;  //       -  equal to sub arm angle (inverted motor)
     delta[Z_AXIS] = cartesian[Z_AXIS];
 
-    /*
+    /**
     SERIAL_ECHOPGM("cartesian x="); SERIAL_ECHO(cartesian[X_AXIS]);
     SERIAL_ECHOPGM(" y="); SERIAL_ECHO(cartesian[Y_AXIS]);
     SERIAL_ECHOPGM(" z="); SERIAL_ECHOLN(cartesian[Z_AXIS]);

Marlin/SanityCheck.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * SanityCheck.h
  *
@@ -198,7 +220,7 @@
    * Check if Probe_Offset * Grid Points is greater than Probing Range
    */
   #if ENABLED(AUTO_BED_LEVELING_GRID)
-    #ifndef DELTA_PROBABLE_RADIUS
+    #ifndef DELTA_PROBEABLE_RADIUS
       // Be sure points are in the right order
       #if LEFT_PROBE_BED_POSITION > RIGHT_PROBE_BED_POSITION
         #error LEFT_PROBE_BED_POSITION must be less than RIGHT_PROBE_BED_POSITION.

Marlin/Sd2Card.cpp

@@ -1,21 +1,30 @@
-/* Arduino Sd2Card Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino Sd2Card Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino Sd2Card Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino Sd2Card Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 

Marlin/Sd2Card.h

@@ -1,21 +1,30 @@
-/* Arduino Sd2Card Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino Sd2Card Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino Sd2Card Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino Sd2Card Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 
 #include "Marlin.h"

Marlin/Sd2PinMap.h

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2010 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2010 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 // Warning this file was generated by a program.
 #include "Marlin.h"

Marlin/SdBaseFile.cpp

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 
 #include "Marlin.h"

Marlin/SdBaseFile.h

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 #if ENABLED(SDSUPPORT)

Marlin/SdFatConfig.h

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 /**
  * \file

Marlin/SdFatStructs.h

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 #if ENABLED(SDSUPPORT)
@@ -28,7 +37,7 @@
  * \file
  * \brief FAT file structures
  */
-/*
+/**
  * mostly from Microsoft document fatgen103.doc
  * http://www.microsoft.com/whdc/system/platform/firmware/fatgen.mspx
  */

Marlin/SdFatUtil.cpp

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2008 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
-
+ *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2008 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 

Marlin/SdFatUtil.h

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2008 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
-
+ *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2008 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 #if ENABLED(SDSUPPORT)

Marlin/SdFile.cpp

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 

Marlin/SdFile.h

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 /**
  * \file

Marlin/SdInfo.h

@@ -1,21 +1,30 @@
-/* Arduino Sd2Card Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino Sd2Card Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino Sd2Card Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino Sd2Card Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 #if ENABLED(SDSUPPORT)

Marlin/SdVolume.cpp

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 #if ENABLED(SDSUPPORT)

Marlin/SdVolume.h

@@ -1,21 +1,30 @@
-/* Arduino SdFat Library
+/**
- * Copyright (C) 2009 by William Greiman
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
- * This file is part of the Arduino SdFat Library
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
  *
- * This Library is free software: you can redistribute it and/or modify
+ * This program is free software: you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation, either version 3 of the License, or
  * (at your option) any later version.
  *
- * This Library is distributed in the hope that it will be useful,
+ * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
- * along with the Arduino SdFat Library.  If not, see
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
- * <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino Sd2Card Library
  */
 #include "Marlin.h"
 #if ENABLED(SDSUPPORT)

Marlin/blinkm.cpp

@@ -1,7 +1,30 @@
-/*
+/**
-  blinkm.cpp - Library for controlling a BlinkM over i2c
+ * Marlin 3D Printer Firmware
-  Created by Tim Koster, August 21 2013.
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
-*/
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * blinkm.cpp - Library for controlling a BlinkM over i2c
+ * Created by Tim Koster, August 21 2013.
+ */
+
 #include "Marlin.h"
 
 #if ENABLED(BLINKM)

Marlin/blinkm.h

@@ -1,6 +1,28 @@
-/*
+/**
-  blinkm.h
+ * Marlin 3D Printer Firmware
-  Library header file for BlinkM library
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * blinkm.h - Library for controlling a BlinkM over i2c
+ * Created by Tim Koster, August 21 2013.
  */
 
 #include "Arduino.h"

Marlin/boards.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 #ifndef BOARDS_H
 #define BOARDS_H
 

Marlin/buzzer.cpp

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 #include "Marlin.h"
 #if HAS_BUZZER
   #include "buzzer.h"

Marlin/buzzer.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 #ifndef BUZZER_H
   #define BUZZER_H
 

Marlin/cardreader.cpp

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 #include "Marlin.h"
 #include "cardreader.h"
 #include "ultralcd.h"
@@ -223,7 +245,7 @@ void CardReader::initsd() {
   }
   workDir = root;
   curDir = &root;
-  /*
+  /**
   if (!workDir.openRoot(&volume)) {
     SERIAL_ECHOLNPGM(MSG_SD_WORKDIR_FAIL);
   }

Marlin/cardreader.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 #ifndef CARDREADER_H
 #define CARDREADER_H
 

Marlin/configuration_store.cpp

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * configuration_store.cpp
  *

Marlin/configuration_store.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 #ifndef CONFIGURATION_STORE_H
 #define CONFIGURATION_STORE_H
 

Marlin/dac_mcp4728.cpp

@@ -1,22 +1,44 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
 
-  mcp4728.cpp - Arduino library for MicroChip MCP4728 I2C D/A converter
+/**
-  For implementation details, please take a look at the datasheet http://ww1.microchip.com/downloads/en/DeviceDoc/22187a.pdf
+ * mcp4728.cpp - Arduino library for MicroChip MCP4728 I2C D/A converter
-  For discussion and feedback, please go to http://arduino.cc/forum/index.php/topic,51842.0.html
+ *
-*/
+ * For implementation details, please take a look at the datasheet:
+ * http://ww1.microchip.com/downloads/en/DeviceDoc/22187a.pdf
+ *
+ * For discussion and feedback, please go to:
+ * http://arduino.cc/forum/index.php/topic,51842.0.html
+ */
 
-
-/* _____PROJECT INCLUDES_____________________________________________________ */
 #include "dac_mcp4728.h"
 
 #if ENABLED(DAC_STEPPER_CURRENT)
 
-// Used Global variables
 uint16_t     mcp4728_values[4];
 
-/*
+/**
-Begin I2C, get current values (input register and eeprom) of mcp4728
+ * Begin I2C, get current values (input register and eeprom) of mcp4728
-*/
+ */
 void mcp4728_init() {
   Wire.begin();
   Wire.requestFrom(int(DAC_DEV_ADDRESS), 24);
@@ -33,19 +55,19 @@ void mcp4728_init() {
   }
 }
 
-/*
+/**
-Write input resister value to specified channel using fastwrite method.
+ * Write input resister value to specified channel using fastwrite method.
-Channel : 0-3, Values : 0-4095
+ * Channel : 0-3, Values : 0-4095
-*/
+ */
 uint8_t mcp4728_analogWrite(uint8_t channel, uint16_t value) {
   mcp4728_values[channel] = value;
   return mcp4728_fastWrite();
 }
-/*
+/**
-Write all input resistor values to EEPROM using SequencialWrite method.
+ * Write all input resistor values to EEPROM using SequencialWrite method.
-This will update both input register and EEPROM value
+ * This will update both input register and EEPROM value
-This will also write current Vref, PowerDown, Gain settings to EEPROM
+ * This will also write current Vref, PowerDown, Gain settings to EEPROM
-*/
+ */
 uint8_t mcp4728_eepromWrite() {
   Wire.beginTransmission(DAC_DEV_ADDRESS);
   Wire.send(SEQWRITE);
@@ -56,31 +78,32 @@ uint8_t mcp4728_eepromWrite() {
   return Wire.endTransmission();
 }
 
-/*
+/**
-  Write Voltage reference setting to all input regiters
+ * Write Voltage reference setting to all input regiters
-*/
+ */
 uint8_t mcp4728_setVref_all(uint8_t value) {
   Wire.beginTransmission(DAC_DEV_ADDRESS);
   Wire.send(VREFWRITE | value << 3 | value << 2 | value << 1 | value);
   return Wire.endTransmission();
 }
-/*
+/**
-  Write Gain setting to all input regiters
+ * Write Gain setting to all input regiters
-*/
+ */
 uint8_t mcp4728_setGain_all(uint8_t value) {
   Wire.beginTransmission(DAC_DEV_ADDRESS);
   Wire.send(GAINWRITE | value << 3 | value << 2 | value << 1 | value);
   return Wire.endTransmission();
 }
 
-/*
+/**
-  Return Input Regiter value
+ * Return Input Regiter value
-*/
+ */
 uint16_t mcp4728_getValue(uint8_t channel) { return mcp4728_values[channel]; }
 
-/*
+/**
-// Steph: Might be useful in the future
+ * Steph: Might be useful in the future
-// Return Vout
+ * Return Vout
+ *
 uint16_t mcp4728_getVout(uint8_t channel) {
   uint32_t vref = 2048;
   uint32_t vOut = (vref * mcp4728_values[channel] * (_DAC_STEPPER_GAIN + 1)) / 4096;
@@ -89,11 +112,11 @@ uint16_t mcp4728_getVout(uint8_t channel) {
 }
 */
 
-/*
+/**
-FastWrite input register values - All DAC ouput update. refer to DATASHEET 5.6.1
+ * FastWrite input register values - All DAC ouput update. refer to DATASHEET 5.6.1
-DAC Input and PowerDown bits update.
+ * DAC Input and PowerDown bits update.
-No EEPROM update
+ * No EEPROM update
-*/
+ */
 uint8_t mcp4728_fastWrite() {
   Wire.beginTransmission(DAC_DEV_ADDRESS);
   for (uint8_t channel=0; channel <= 3; channel++) {
@@ -103,9 +126,9 @@ uint8_t mcp4728_fastWrite() {
   return Wire.endTransmission();
 }
 
-/*
+/**
-Common function for simple general commands
+ * Common function for simple general commands
-*/
+ */
 uint8_t mcp4728_simpleCommand(byte simpleCommand) {
   Wire.beginTransmission(GENERALCALL);
   Wire.send(simpleCommand);

Marlin/dac_mcp4728.h

@@ -1,6 +1,28 @@
 /**
-Arduino library for MicroChip MCP4728 I2C D/A converter.
+ * Marlin 3D Printer Firmware
-*/
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino library for MicroChip MCP4728 I2C D/A converter.
+ */
 
 #ifndef mcp4728_h
 #define mcp4728_h

Marlin/digipot_mcp4451.cpp

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 #include "Configuration.h"
 
 #if ENABLED(DIGIPOT_I2C)

Marlin/dogm_bitmaps.h

@@ -1,6 +1,31 @@
-// BitMap for splashscreen
+/**
-// Generated with: http://www.digole.com/tools/PicturetoC_Hex_converter.php
+ * Marlin 3D Printer Firmware
-// Please note that using the high-res version takes 402Bytes of PROGMEM.
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * BitMap for splashscreen
+ * Generated with: http://www.digole.com/tools/PicturetoC_Hex_converter.php
+ * Please note that using the high-res version takes 402Bytes of PROGMEM.
+ */
+
 //#define START_BMPHIGH
 
 #if ENABLED(SHOW_BOOTSCREEN)

Marlin/dogm_font_data_6x9_marlin.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: -Misc-Fixed-Medium-R-Normal--9-90-75-75-C-60-ISO10646-1
   Copyright: Public domain font.  Share and enjoy.
   Capital A Height: 6, '1' Height: 6

Marlin/dogm_font_data_HD44780_C.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: HD44780_C v1.2
   Copyright: A. Hardtung, public domain
   Capital A Height: 7, '1' Height: 7

Marlin/dogm_font_data_HD44780_J.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: HD44780_J
   Copyright: A. Hardtung, public domain
   Capital A Height: 7, '1' Height: 7

Marlin/dogm_font_data_HD44780_W.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: HD44780_W
   Copyright: A.Hardtung, public domain
   Capital A Height: 7, '1' Height: 7

Marlin/dogm_font_data_ISO10646_1.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: ISO10646-1
   Copyright: A.Hardtung, public domain
   Capital A Height: 7, '1' Height: 7

Marlin/dogm_font_data_ISO10646_5_Cyrillic.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: ISO10646_5_Cyrillic
   Copyright: A. Hardtung, public domain
   Capital A Height: 7, '1' Height: 7

Marlin/dogm_font_data_ISO10646_CN.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: ISO10646_CN
   Copyright: A. Hardtung, public domain
   Capital A Height: 7, '1' Height: 7

Marlin/dogm_font_data_ISO10646_Kana.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: ISO10646_Kana
   Copyright: A. Hardtung, public domain
   Capital A Height: 7, '1' Height: 7

Marlin/dogm_font_data_Marlin_symbols.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   Fontname: Marlin_symbols
   Copyright: Created with Fony 1.4.7
   Capital A Height: 0, '1' Height: 0

Marlin/dogm_lcd_implementation.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * dogm_lcd_implementation.h
  *

Marlin/example_configurations/Felix/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/Felix/Configuration_DUAL.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/Felix/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/Hephestos/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/Hephestos/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/K8200/Configuration.h

@@ -1,8 +1,47 @@
-// Sample configuration file for Vellemann K8200
+/**
-// tested on K8200 with VM8201 (Display)
+ * Marlin 3D Printer Firmware
-// and Arduino 1.6.8 (Mac) by @CONSULitAS, 2016-02-21
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
-// https://github.com/CONSULitAS/Marlin-K8200/archive/K8200_stable_2016-02-21.zip
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
 
+/**
+ * Sample configuration file for Vellemann K8200
+ * tested on K8200 with VM8201 (Display)
+ * and Arduino 1.6.8 (Mac) by @CONSULitAS, 2016-02-21
+ * https://github.com/CONSULitAS/Marlin-K8200/archive/K8200_stable_2016-02-21.zip
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -12,8 +51,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -21,11 +62,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/K8200/Configuration_adv.h

@@ -1,8 +1,41 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 // Sample configuration file for Vellemann K8200
 // tested on K8200 with VM8201 (Display)
 // and Arduino 1.6.8 (Mac) by @CONSULitAS, 2016-02-21
 // https://github.com/CONSULitAS/Marlin-K8200/archive/K8200_stable_2016-02-21.zip
 
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/RigidBot/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/RigidBot/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/SCARA/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/TAZ4/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/TAZ4/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/WITBOX/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/WITBOX/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================
@@ -545,11 +580,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
     // Set the rectangle in which to probe.
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
 

Marlin/example_configurations/delta/biv2.5/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/delta/generic/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================
@@ -545,11 +580,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
     // set the rectangle in which to probe
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
 

Marlin/example_configurations/delta/generic/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================
@@ -545,11 +580,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
     // set the rectangle in which to probe
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
 

Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -1,7 +1,46 @@
-// Example configuration file for OpenBeam Kossel Pro
+/**
-// tested on 2015-05-19 by @Wackerbarth
+ * Marlin 3D Printer Firmware
-// using Arduino 1.6.5 (Mac)
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
 
+/**
+ * Example configuration file for OpenBeam Kossel Pro
+ * tested on 2015-05-19 by @Wackerbarth
+ * using Arduino 1.6.5 (Mac)
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -11,8 +50,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -20,11 +61,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================
@@ -532,11 +569,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
     // set the rectangle in which to probe
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS-25)
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS-25)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
 

Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h

@@ -1,7 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 // Example configuration file for OpenBeam Kossel Pro
 // tested on 2015-05-19 by @Wackerbarth
 // using Arduino 1.6.5 (Mac)
 
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================
@@ -537,11 +572,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
   #if ENABLED(AUTO_BED_LEVELING_GRID)
 
-    #define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
+    #define DELTA_PROBEABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
-    #define LEFT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define LEFT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define RIGHT_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define RIGHT_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
-    #define FRONT_PROBE_BED_POSITION -DELTA_PROBABLE_RADIUS
+    #define FRONT_PROBE_BED_POSITION -DELTA_PROBEABLE_RADIUS
-    #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
+    #define BACK_PROBE_BED_POSITION DELTA_PROBEABLE_RADIUS
 
     #define MIN_PROBE_EDGE 20 // The Z probe minimum square sides can be no smaller than this.
 

Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/makibox/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -1,3 +1,40 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
 #ifndef CONFIGURATION_H
 #define CONFIGURATION_H
 
@@ -7,8 +44,10 @@
 //===========================================================================
 //============================= Getting Started =============================
 //===========================================================================
-/*
+
-Here are some standard links for getting your machine calibrated:
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
  * http://reprap.org/wiki/Calibration
  * http://youtu.be/wAL9d7FgInk
  * http://calculator.josefprusa.cz
@@ -16,11 +55,7 @@ Here are some standard links for getting your machine calibrated:
  * http://www.thingiverse.com/thing:5573
  * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
  * http://www.thingiverse.com/thing:298812
-*/
+ */
-
-// This configuration file contains the basic settings.
-// Advanced settings can be found in Configuration_adv.h
-// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
 
 //===========================================================================
 //============================= DELTA Printer ===============================

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -1,3 +1,35 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
 #ifndef CONFIGURATION_ADV_H
 #define CONFIGURATION_ADV_H
 

Marlin/fastio.h

@@ -1,4 +1,26 @@
-/*
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
   This code contributed by Triffid_Hunter and modified by Kliment
   why double up on these macros? see http://gcc.gnu.org/onlinedocs/cpp/Stringification.html
 */
@@ -8,7 +30,7 @@
 
 #include <avr/io.h>
 
-/*
+/**
   utility functions
 */
 
@@ -16,7 +38,7 @@
   #define MASK(PIN)  (1 << PIN)
 #endif
 
-/*
+/**
   magic I/O routines
   now you can simply SET_OUTPUT(STEP); WRITE(STEP, 1); WRITE(STEP, 0);
 */
@@ -85,7 +107,7 @@
 // Shorthand
 #define OUT_WRITE(IO, v) { SET_OUTPUT(IO); WRITE(IO, v); }
 
-/*
+/**
   ports and functions
 
   added as necessary or if I feel like it- not a comprehensive list!
@@ -116,7 +138,7 @@
 
   #define DEBUG_LED   AIO5
 
-  /*
+  /**
   pins
   */
 
@@ -455,7 +477,7 @@
   #define OC2B        DIO14
 
   #define DEBUG_LED   DIO0
-  /*
+  /**
   pins
   */
 
@@ -964,7 +986,7 @@
   // change for your board
   #define DEBUG_LED   DIO21
 
-  /*
+  /**
   pins
   */
   #define DIO0_PIN    PINE0
@@ -2034,7 +2056,7 @@
   // change for your board
   #define DEBUG_LED   DIO31 /* led D5 red */
 
-  /*
+  /**
   pins
   */
 
@@ -2676,7 +2698,7 @@
 
   #else // AT90USBxx_TEENSYPP_ASSIGNMENTS -- Use Teensyduino Teensy++2.0 assignments.
 
-    /*
+    /**
 
     AT90USB  51 50 49 48 47 46 45 44 10 11 12 13 14 15 16 17 35 36 37 38 39 40 41 42 25 26 27 28 29 30 31 32 33 34 43 09 18 19 01 02 61 60 59 58 57 56 55 54
     Port     A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B2 B3 B4 B5 B6 B7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 E0 E1 E2 E3 E4 E5 E6 E7 F0 F1 F2 F3 F4 F5 F6 F7
@@ -3351,7 +3373,7 @@
   // change for your board
   #define DEBUG_LED   DIO46
 
-  /*
+  /**
   pins
   */
   #define DIO0_PIN    PINE0

Marlin/language.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 #ifndef LANGUAGE_H
 #define LANGUAGE_H
 

Marlin/language_an.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Aragonese
  *

Marlin/language_bg.h

@@ -1,4 +1,26 @@
 /**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
  * Bulgarian
  *
  * LCD Menu Messages

Marlin/language_ca.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Catalan
  *

Marlin/language_cn.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Chinese
  *

Marlin/language_cz.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Czech
  *

Marlin/language_da.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Danish
  *

Marlin/language_de.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * German
  *

Marlin/language_en.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * English
  *

Marlin/language_es.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Spanish
  *

Marlin/language_eu.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Basque-Euskera
  *

Marlin/language_fi.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Finnish
  *

Marlin/language_fr.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * French
  *

Marlin/language_gl.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Galician language (ISO "gl")
  *

Marlin/language_it.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Italian
  *

Marlin/language_kana.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Japanese (Kana)
  *

Marlin/language_kana_utf8.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Japanese (Kana UTF8 version)
  *

Marlin/language_nl.h

@@ -1,3 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
 /**
  * Dutch
  *