diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 05701ce19c..f5e753882a 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/Marlin.cpp b/Marlin/src/Marlin.cpp
index 9720d824fa..e7d4a37fe3 100644
--- a/Marlin/src/Marlin.cpp
+++ b/Marlin/src/Marlin.cpp
@@ -40,6 +40,8 @@
 #include "sd/cardreader.h"
 #include "module/configuration_store.h"
 #include "module/printcounter.h" // PrintCounter or Stopwatch
+#include "feature/closedloop.h"
+
 #ifdef ARDUINO
   #include <pins_arduino.h>
 #endif
@@ -903,6 +905,10 @@ void setup() {
   #if ENABLED(USE_WATCHDOG) // Reinit watchdog after HAL_get_reset_source call
     watchdog_init();
   #endif
+
+  #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+    init_closedloop();
+  #endif
 }
 
 /**
diff --git a/Marlin/src/config/default/Configuration_adv.h b/Marlin/src/config/default/Configuration_adv.h
index 05701ce19c..f5e753882a 100755
--- a/Marlin/src/config/default/Configuration_adv.h
+++ b/Marlin/src/config/default/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index 196bcea2a9..d1a3b68d5d 100644
--- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Anet/A2/Configuration_adv.h b/Marlin/src/config/examples/Anet/A2/Configuration_adv.h
index 2e3ca3cf31..9f03da8335 100644
--- a/Marlin/src/config/examples/Anet/A2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h b/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
index 2e3ca3cf31..9f03da8335 100644
--- a/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A2plus/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
index 7e8b309353..0aae0b459f 100644
--- a/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A6/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
index 2db18a1c8b..ae78b09d93 100644
--- a/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Anet/A8/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
index 05701ce19c..f5e753882a 100644
--- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
+++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index 931e42658e..569de9106f 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 2f19cb82c6..55b288c6d8 100644
--- a/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/Marlin/src/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
index 564437a5a1..5d31d53404 100644
--- a/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
index c734d16447..6d99f4eccf 100644
--- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
index 564437a5a1..5d31d53404 100644
--- a/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Cartesio/Configuration_adv.h b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
index 74dfd980bd..b8b5283a93 100644
--- a/Marlin/src/config/examples/Cartesio/Configuration_adv.h
+++ b/Marlin/src/config/examples/Cartesio/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
index 2c06e048fa..658c892c78 100755
--- a/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
index 5219cbdb59..3d9d5fe7f9 100644
--- a/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
index 16f84ea6d2..27d7764175 100644
--- a/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
index f9f494947b..3380586f7f 100644
--- a/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/CR-8/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
index 2452d8bca3..c4b53e9c15 100644
--- a/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
index 11ab312c36..70181295c0 100644
--- a/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
index f9f494947b..3380586f7f 100644
--- a/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/Marlin/src/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Einstart-S/Configuration_adv.h b/Marlin/src/config/examples/Einstart-S/Configuration_adv.h
index 4cfdd7c032..c7e0d1e6b6 100644
--- a/Marlin/src/config/examples/Einstart-S/Configuration_adv.h
+++ b/Marlin/src/config/examples/Einstart-S/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Felix/Configuration_adv.h b/Marlin/src/config/examples/Felix/Configuration_adv.h
index f114b563e3..7efa557ddd 100644
--- a/Marlin/src/config/examples/Felix/Configuration_adv.h
+++ b/Marlin/src/config/examples/Felix/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index 85e571875d..1c439efa83 100644
--- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h b/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h
index a38541d25e..1b08edcdb3 100644
--- a/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h
+++ b/Marlin/src/config/examples/Formbot/T-Rex_2+/Configuration_adv.h
@@ -291,6 +291,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index 3fd8d9666c..a801220737 100644
--- a/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/Marlin/src/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -291,6 +291,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index bedd6aae13..8db16bd2f3 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index bedd6aae13..8db16bd2f3 100644
--- a/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
index 2b44b0c0da..261ab2b3c7 100644
--- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
index 35447d2f35..5203f496ac 100644
--- a/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/Marlin/src/config/examples/JGAurora/A5/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/MakerParts/Configuration_adv.h b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
index b2de733082..928ce844eb 100644
--- a/Marlin/src/config/examples/MakerParts/Configuration_adv.h
+++ b/Marlin/src/config/examples/MakerParts/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
index 8ef550a7d8..82231d679d 100644
--- a/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M150/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
index 1db6b9e425..e352661347 100644
--- a/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Malyan/M200/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 #define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index 8e1d2df13e..111ebceebf 100644
--- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
index acc9e3d11f..4da0dd6fb2 100644
--- a/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/Marlin/src/config/examples/Mks/Sbase/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/RigidBot/Configuration_adv.h b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
index 4dd0305c66..03532f37a1 100644
--- a/Marlin/src/config/examples/RigidBot/Configuration_adv.h
+++ b/Marlin/src/config/examples/RigidBot/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/SCARA/Configuration_adv.h b/Marlin/src/config/examples/SCARA/Configuration_adv.h
index 405eec5250..dc61216864 100644
--- a/Marlin/src/config/examples/SCARA/Configuration_adv.h
+++ b/Marlin/src/config/examples/SCARA/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
index 22eb8a647b..5b48aebf14 100644
--- a/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
+++ b/Marlin/src/config/examples/Sanguinololu/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/TheBorg/Configuration_adv.h b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
index 45bd6482c8..186615ab56 100644
--- a/Marlin/src/config/examples/TheBorg/Configuration_adv.h
+++ b/Marlin/src/config/examples/TheBorg/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
index f9bf3e7e64..b6368c8703 100644
--- a/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
+++ b/Marlin/src/config/examples/TinyBoy2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h b/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
index 08bed247fe..45710cd5f4 100644
--- a/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/Marlin/src/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
index 8ed4c3f8ea..ad86e61d2e 100644
--- a/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/Marlin/src/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
index ab14d61d96..0dd094abfc 100644
--- a/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8200/Configuration_adv.h
@@ -300,6 +300,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
index 61e6742a82..6ee6470a87 100644
--- a/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/Marlin/src/config/examples/Velleman/K8400/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index fc62ed6732..554d5fd376 100644
--- a/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/Marlin/src/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index f02ec1b7c1..827105953f 100644
--- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index f02ec1b7c1..827105953f 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index c4e932d703..9202223428 100644
--- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/generic/Configuration_adv.h b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
index c4e932d703..9202223428 100644
--- a/Marlin/src/config/examples/delta/generic/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/generic/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
index c4e932d703..9202223428 100644
--- a/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
index 0718fb470a..c9e93722fe 100644
--- a/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration_adv.h
@@ -292,6 +292,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
index 74ebb3c3a2..4c78080b62 100644
--- a/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index 9f029fa7cf..620c4b5171 100644
--- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/makibox/Configuration_adv.h b/Marlin/src/config/examples/makibox/Configuration_adv.h
index 43893f4de8..9c2767b080 100644
--- a/Marlin/src/config/examples/makibox/Configuration_adv.h
+++ b/Marlin/src/config/examples/makibox/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
index 8e387d1d68..e762501ba9 100644
--- a/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/config/examples/wt150/Configuration_adv.h b/Marlin/src/config/examples/wt150/Configuration_adv.h
index 9aa7f5a49d..567bd706ef 100644
--- a/Marlin/src/config/examples/wt150/Configuration_adv.h
+++ b/Marlin/src/config/examples/wt150/Configuration_adv.h
@@ -287,6 +287,13 @@
 
 //#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
 
+// Employ an external closed loop controller. Override pins here if needed.
+//#define EXTERNAL_CLOSED_LOOP_CONTROLLER
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+  //#define CLOSED_LOOP_ENABLE_PIN        -1
+  //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1
+#endif
+
 /**
  * Dual Steppers / Dual Endstops
  *
diff --git a/Marlin/src/feature/closedloop.cpp b/Marlin/src/feature/closedloop.cpp
new file mode 100644
index 0000000000..2fe60fcf9c
--- /dev/null
+++ b/Marlin/src/feature/closedloop.cpp
@@ -0,0 +1,41 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#include "../inc/MarlinConfig.h"
+
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+
+#if !PIN_EXISTS(CLOSED_LOOP_ENABLE) || !PIN_EXISTS(CLOSED_LOOP_MOVE_COMPLETE)
+  #error "CLOSED_LOOP_ENABLE_PIN and CLOSED_LOOP_MOVE_COMPLETE_PIN are required for EXTERNAL_CLOSED_LOOP_CONTROLLER."
+#endif
+
+#include "closedloop.h"
+
+void init_closedloop() {
+  OUT_WRITE(CLOSED_LOOP_ENABLE_PIN, LOW);
+  SET_INPUT_PULLUP(CLOSED_LOOP_MOVE_COMPLETE_PIN);
+}
+
+void set_closedloop(const byte val) {
+  OUT_WRITE(CLOSED_LOOP_ENABLE_PIN, val);
+}
+
+#endif // EXTERNAL_CLOSED_LOOP_CONTROLLER
diff --git a/Marlin/src/feature/closedloop.h b/Marlin/src/feature/closedloop.h
new file mode 100644
index 0000000000..84cec36fe6
--- /dev/null
+++ b/Marlin/src/feature/closedloop.h
@@ -0,0 +1,25 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+void init_closedloop();
+void set_closedloop(const byte val);
diff --git a/Marlin/src/gcode/calibrate/M12.cpp b/Marlin/src/gcode/calibrate/M12.cpp
new file mode 100644
index 0000000000..a4b75e71bd
--- /dev/null
+++ b/Marlin/src/gcode/calibrate/M12.cpp
@@ -0,0 +1,36 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#include "../../inc/MarlinConfigPre.h"
+
+#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+
+#include "../gcode.h"
+#include "../../module/planner.h"
+#include "../../feature/closedloop.h"
+
+void GcodeSuite::M12() {
+  planner.synchronize();
+  if (parser.seenval('S'))
+    set_closedloop(parser.value_int()); // Force a CLC set
+}
+
+#endif
diff --git a/Marlin/src/gcode/gcode.cpp b/Marlin/src/gcode/gcode.cpp
index 6682cfbeb9..063f32999f 100644
--- a/Marlin/src/gcode/gcode.cpp
+++ b/Marlin/src/gcode/gcode.cpp
@@ -292,6 +292,10 @@ void GcodeSuite::process_parsed_command(
         case 5: M5(); break;                                      // M5 - turn spindle/laser off
       #endif
 
+      #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+        case 12: M12(); break;                                    // M12: Synchronize and optionally force a CLC set
+      #endif
+
       case 17: M17(); break;                                      // M17: Enable all stepper motors
 
       #if ENABLED(SDSUPPORT)
diff --git a/Marlin/src/gcode/gcode.h b/Marlin/src/gcode/gcode.h
index cb9e03b58f..36d8fc3fc3 100644
--- a/Marlin/src/gcode/gcode.h
+++ b/Marlin/src/gcode/gcode.h
@@ -76,6 +76,7 @@
  * M3   - Turn laser/spindle on, set spindle/laser speed/power, set rotation to clockwise
  * M4   - Turn laser/spindle on, set spindle/laser speed/power, set rotation to counter-clockwise
  * M5   - Turn laser/spindle off
+ * M12  - Set up closed loop control system. More features coming soon. (Requires EXTERNAL_CLOSED_LOOP_CONTROLLER)
  * M17  - Enable/Power all stepper motors
  * M18  - Disable all stepper motors; same as M84
  * M20  - List SD card. (Requires SDSUPPORT)
@@ -438,6 +439,10 @@ private:
     static void M5();
   #endif
 
+  #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+    static void M12();
+  #endif
+
   static void M17();
 
   static void M18_M84();
diff --git a/Marlin/src/module/planner.cpp b/Marlin/src/module/planner.cpp
index 43f7a40a41..4db6e58d48 100644
--- a/Marlin/src/module/planner.cpp
+++ b/Marlin/src/module/planner.cpp
@@ -1539,7 +1539,14 @@ float Planner::get_axis_position_mm(const AxisEnum axis) {
 /**
  * Block until all buffered steps are executed / cleaned
  */
-void Planner::synchronize() { while (has_blocks_queued() || cleaning_buffer_counter) idle(); }
+void Planner::synchronize() {
+  while (
+    has_blocks_queued() || cleaning_buffer_counter
+    #if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER)
+      || !READ(CLOSED_LOOP_MOVE_COMPLETE_PIN)
+    #endif
+  ) idle();
+}
 
 /**
  * Planner::_buffer_steps