Simplify / undef extra endstops (#21808)
Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
This commit is contained in:
@@ -1983,15 +1983,6 @@
|
||||
#if _HAS_STOP(Z,MAX)
|
||||
#define HAS_Z_MAX 1
|
||||
#endif
|
||||
#if _HAS_STOP(X,STOP)
|
||||
#define HAS_X_STOP 1
|
||||
#endif
|
||||
#if _HAS_STOP(Y,STOP)
|
||||
#define HAS_Y_STOP 1
|
||||
#endif
|
||||
#if _HAS_STOP(Z,STOP)
|
||||
#define HAS_Z_STOP 1
|
||||
#endif
|
||||
#if PIN_EXISTS(X2_MIN)
|
||||
#define HAS_X2_MIN 1
|
||||
#endif
|
||||
@@ -2022,10 +2013,17 @@
|
||||
#if PIN_EXISTS(Z4_MAX)
|
||||
#define HAS_Z4_MAX 1
|
||||
#endif
|
||||
#if HAS_CUSTOM_PROBE_PIN && PIN_EXISTS(Z_MIN_PROBE)
|
||||
#if BOTH(HAS_BED_PROBE, HAS_CUSTOM_PROBE_PIN) && PIN_EXISTS(Z_MIN_PROBE)
|
||||
#define HAS_Z_MIN_PROBE_PIN 1
|
||||
#endif
|
||||
|
||||
#undef IS_PROBE_PIN
|
||||
#undef IS_X2_ENDSTOP
|
||||
#undef IS_Y2_ENDSTOP
|
||||
#undef IS_Z2_ENDSTOP
|
||||
#undef IS_Z3_ENDSTOP
|
||||
#undef IS_Z4_ENDSTOP
|
||||
|
||||
//
|
||||
// ADC Temp Sensors (Thermistor or Thermocouple with amplifier ADC interface)
|
||||
//
|
||||
|
@@ -2101,105 +2101,28 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal
|
||||
|
||||
// Dual/multiple endstops requirements
|
||||
#if ENABLED(X_DUAL_ENDSTOPS)
|
||||
#if !X2_USE_ENDSTOP
|
||||
#error "You must set X2_USE_ENDSTOP with X_DUAL_ENDSTOPS."
|
||||
#elif X2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
|
||||
#error "USE_XMIN_PLUG is required when X2_USE_ENDSTOP is _XMIN_."
|
||||
#elif X2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
|
||||
#error "USE_XMAX_PLUG is required when X2_USE_ENDSTOP is _XMAX_."
|
||||
#elif X2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
|
||||
#error "USE_YMIN_PLUG is required when X2_USE_ENDSTOP is _YMIN_."
|
||||
#elif X2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
|
||||
#error "USE_YMAX_PLUG is required when X2_USE_ENDSTOP is _YMAX_."
|
||||
#elif X2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
|
||||
#error "USE_ZMIN_PLUG is required when X2_USE_ENDSTOP is _ZMIN_."
|
||||
#elif X2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
|
||||
#error "USE_ZMAX_PLUG is required when X2_USE_ENDSTOP is _ZMAX_."
|
||||
#elif !HAS_X2_MIN && !HAS_X2_MAX
|
||||
#error "X2_USE_ENDSTOP has been assigned to a nonexistent endstop!"
|
||||
#elif ENABLED(DELTA)
|
||||
#if ENABLED(DELTA)
|
||||
#error "X_DUAL_ENDSTOPS is not compatible with DELTA."
|
||||
#elif !X2_USE_ENDSTOP
|
||||
#error "X2_USE_ENDSTOP must be set with X_DUAL_ENDSTOPS."
|
||||
#endif
|
||||
#endif
|
||||
#if ENABLED(Y_DUAL_ENDSTOPS)
|
||||
#if !Y2_USE_ENDSTOP
|
||||
#error "You must set Y2_USE_ENDSTOP with Y_DUAL_ENDSTOPS."
|
||||
#elif Y2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
|
||||
#error "USE_XMIN_PLUG is required when Y2_USE_ENDSTOP is _XMIN_."
|
||||
#elif Y2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
|
||||
#error "USE_XMAX_PLUG is required when Y2_USE_ENDSTOP is _XMAX_."
|
||||
#elif Y2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
|
||||
#error "USE_YMIN_PLUG is required when Y2_USE_ENDSTOP is _YMIN_."
|
||||
#elif Y2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
|
||||
#error "USE_YMAX_PLUG is required when Y2_USE_ENDSTOP is _YMAX_."
|
||||
#elif Y2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
|
||||
#error "USE_ZMIN_PLUG is required when Y2_USE_ENDSTOP is _ZMIN_."
|
||||
#elif Y2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
|
||||
#error "USE_ZMAX_PLUG is required when Y2_USE_ENDSTOP is _ZMAX_."
|
||||
#elif !HAS_Y2_MIN && !HAS_Y2_MAX
|
||||
#error "Y2_USE_ENDSTOP has been assigned to a nonexistent endstop!"
|
||||
#elif ENABLED(DELTA)
|
||||
#if ENABLED(DELTA)
|
||||
#error "Y_DUAL_ENDSTOPS is not compatible with DELTA."
|
||||
#elif !Y2_USE_ENDSTOP
|
||||
#error "Y2_USE_ENDSTOP must be set with Y_DUAL_ENDSTOPS."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(Z_MULTI_ENDSTOPS)
|
||||
#if !Z2_USE_ENDSTOP
|
||||
#error "You must set Z2_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 2."
|
||||
#elif Z2_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
|
||||
#error "USE_XMIN_PLUG is required when Z2_USE_ENDSTOP is _XMIN_."
|
||||
#elif Z2_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
|
||||
#error "USE_XMAX_PLUG is required when Z2_USE_ENDSTOP is _XMAX_."
|
||||
#elif Z2_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
|
||||
#error "USE_YMIN_PLUG is required when Z2_USE_ENDSTOP is _YMIN_."
|
||||
#elif Z2_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
|
||||
#error "USE_YMAX_PLUG is required when Z2_USE_ENDSTOP is _YMAX_."
|
||||
#elif Z2_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
|
||||
#error "USE_ZMIN_PLUG is required when Z2_USE_ENDSTOP is _ZMIN_."
|
||||
#elif Z2_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
|
||||
#error "USE_ZMAX_PLUG is required when Z2_USE_ENDSTOP is _ZMAX_."
|
||||
#elif !HAS_Z2_MIN && !HAS_Z2_MAX
|
||||
#error "Z2_USE_ENDSTOP has been assigned to a nonexistent endstop!"
|
||||
#elif ENABLED(DELTA)
|
||||
#if ENABLED(DELTA)
|
||||
#error "Z_MULTI_ENDSTOPS is not compatible with DELTA."
|
||||
#endif
|
||||
#if NUM_Z_STEPPER_DRIVERS >= 3
|
||||
#if !Z3_USE_ENDSTOP
|
||||
#error "You must set Z3_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 3."
|
||||
#elif Z3_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
|
||||
#error "USE_XMIN_PLUG is required when Z3_USE_ENDSTOP is _XMIN_."
|
||||
#elif Z3_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
|
||||
#error "USE_XMAX_PLUG is required when Z3_USE_ENDSTOP is _XMAX_."
|
||||
#elif Z3_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
|
||||
#error "USE_YMIN_PLUG is required when Z3_USE_ENDSTOP is _YMIN_."
|
||||
#elif Z3_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
|
||||
#error "USE_YMAX_PLUG is required when Z3_USE_ENDSTOP is _YMAX_."
|
||||
#elif Z3_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
|
||||
#error "USE_ZMIN_PLUG is required when Z3_USE_ENDSTOP is _ZMIN_."
|
||||
#elif Z3_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
|
||||
#error "USE_ZMAX_PLUG is required when Z3_USE_ENDSTOP is _ZMAX_."
|
||||
#elif !HAS_Z3_MIN && !HAS_Z3_MAX
|
||||
#error "Z3_USE_ENDSTOP has been assigned to a nonexistent endstop!"
|
||||
#endif
|
||||
#endif
|
||||
#if NUM_Z_STEPPER_DRIVERS >= 4
|
||||
#if !Z4_USE_ENDSTOP
|
||||
#error "You must set Z4_USE_ENDSTOP with Z_MULTI_ENDSTOPS when NUM_Z_STEPPER_DRIVERS >= 4."
|
||||
#elif Z4_USE_ENDSTOP == _XMIN_ && DISABLED(USE_XMIN_PLUG)
|
||||
#error "USE_XMIN_PLUG is required when Z4_USE_ENDSTOP is _XMIN_."
|
||||
#elif Z4_USE_ENDSTOP == _XMAX_ && DISABLED(USE_XMAX_PLUG)
|
||||
#error "USE_XMAX_PLUG is required when Z4_USE_ENDSTOP is _XMAX_."
|
||||
#elif Z4_USE_ENDSTOP == _YMIN_ && DISABLED(USE_YMIN_PLUG)
|
||||
#error "USE_YMIN_PLUG is required when Z4_USE_ENDSTOP is _YMIN_."
|
||||
#elif Z4_USE_ENDSTOP == _YMAX_ && DISABLED(USE_YMAX_PLUG)
|
||||
#error "USE_YMAX_PLUG is required when Z4_USE_ENDSTOP is _YMAX_."
|
||||
#elif Z4_USE_ENDSTOP == _ZMIN_ && DISABLED(USE_ZMIN_PLUG)
|
||||
#error "USE_ZMIN_PLUG is required when Z4_USE_ENDSTOP is _ZMIN_."
|
||||
#elif Z4_USE_ENDSTOP == _ZMAX_ && DISABLED(USE_ZMAX_PLUG)
|
||||
#error "USE_ZMAX_PLUG is required when Z4_USE_ENDSTOP is _ZMAX_."
|
||||
#elif !HAS_Z4_MIN && !HAS_Z4_MAX
|
||||
#error "Z4_USE_ENDSTOP has been assigned to a nonexistent endstop!"
|
||||
#endif
|
||||
#elif !Z2_USE_ENDSTOP
|
||||
#error "Z2_USE_ENDSTOP must be set with Z_MULTI_ENDSTOPS."
|
||||
#elif !Z3_USE_ENDSTOP && NUM_Z_STEPPER_DRIVERS >= 3
|
||||
#error "Z3_USE_ENDSTOP must be set with Z_MULTI_ENDSTOPS and NUM_Z_STEPPER_DRIVERS >= 3."
|
||||
#elif !Z4_USE_ENDSTOP && NUM_Z_STEPPER_DRIVERS >= 4
|
||||
#error "Z4_USE_ENDSTOP must be set with Z_MULTI_ENDSTOPS and NUM_Z_STEPPER_DRIVERS >= 4."
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
Reference in New Issue
Block a user