Proposed changes
This is what I did yesterday: - basicly gave the tests more comprehensive names; put all the declarations at the top; got rid of the magic negative C-value (renamed to P + A, O, T) - "cos(RADIANS(180 + 30 * axis)) * (1 + circles * 0.1 * ((zig_zag) ? 1 : -1)) * delta_calibration_radius" compiles wrong is zig_zag statement is without brackets - DELTA_TOWER_ANGLE_TRIM reset to 3 values (the calcs use the 3th value to normalize will not compile otherwise) -Wrote 3 dummies to keep EEPROM lenght the same -Reset the configs to the 'original' with autocal + menu disabled (but can be enabled of course)
This commit is contained in:
LVD-AC
teemuatlut
@ -450,21 +450,12 @@
|
||||
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 218.0 // mm
|
||||
/*
|
||||
// Horizontal offset from middle of printer to smooth rod center.
|
||||
#define DELTA_SMOOTH_ROD_OFFSET 150.0 // mm
|
||||
|
||||
// Horizontal offset of the universal joints on the end effector.
|
||||
#define DELTA_EFFECTOR_OFFSET 24.0 // mm
|
||||
|
||||
// Horizontal offset of the universal joints on the carriages.
|
||||
#define DELTA_CARRIAGE_OFFSET 22.0 // mm
|
||||
*/
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS 100.00 //mm // get this value from auto calibrate
|
||||
|
||||
// height from z=0.00 to home position
|
||||
#define DELTA_HEIGHT 295.00 // get this value from auto calibrate - use G33 C-1 at 1st time calibration
|
||||
// height from z=0 to home position
|
||||
#define DELTA_HEIGHT 295.00 // get this value from auto calibrate - use G33 P1 A at 1st time calibration
|
||||
|
||||
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
|
||||
#define DELTA_PRINTABLE_RADIUS 85.0
|
||||
@ -486,16 +477,16 @@
|
||||
// After homing move down to a height where XY movement is unconstrained
|
||||
#define DELTA_HOME_TO_SAFE_ZONE
|
||||
|
||||
#define DELTA_ENDSTOP_ADJ { -0.00, -0.00, -0.00 } // get these from auto calibrate
|
||||
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// Trim adjustments for individual towers
|
||||
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
|
||||
// measured in degrees anticlockwise looking from above the printer
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0.00, 0.00 } // get these from auto calibrate
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// delta radius and diaginal rod adjustments measured in mm
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0, 0, 0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
|
||||
|
||||
#endif
|
||||
|
||||
@ -604,7 +595,7 @@
|
||||
#define DEFAULT_XJERK 20.0
|
||||
#define DEFAULT_YJERK DEFAULT_XJERK
|
||||
#define DEFAULT_ZJERK DEFAULT_YJERK // Must be same as XY for delta
|
||||
#define DEFAULT_EJERK 5.0
|
||||
#define DEFAULT_EJERK 5.0
|
||||
|
||||
|
||||
/**
|
||||
@ -670,6 +661,9 @@
|
||||
* is enabled then it also applies to Z_PROBE_SPEED_SLOW.
|
||||
*/
|
||||
|
||||
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
|
||||
//#define SOLENOID_PROBE
|
||||
|
||||
// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
|
||||
//#define Z_PROBE_SLED
|
||||
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
@ -704,7 +698,7 @@
|
||||
#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
|
||||
|
||||
// Speed for the "accurate" probe of each point
|
||||
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 6)
|
||||
#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST) / 6
|
||||
|
||||
// Use double touch for probing
|
||||
//#define PROBE_DOUBLE_TOUCH
|
||||
@ -728,7 +722,7 @@
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_X 0.0
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Y DELTA_PRINTABLE_RADIUS
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_Z 100.0
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED/10)
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_SPEED)/10
|
||||
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_X Z_PROBE_ALLEN_KEY_DEPLOY_2_X * 0.75
|
||||
#define Z_PROBE_ALLEN_KEY_DEPLOY_3_Y Z_PROBE_ALLEN_KEY_DEPLOY_2_Y * 0.75
|
||||
@ -868,7 +862,7 @@
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR true
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// Enable this option for Toshiba steppers drivers
|
||||
//#define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// @section extruder
|
||||
|
||||
@ -448,7 +448,7 @@
|
||||
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 218.0 // mm
|
||||
/*
|
||||
|
||||
// Horizontal offset from middle of printer to smooth rod center.
|
||||
#define DELTA_SMOOTH_ROD_OFFSET 150.0 // mm
|
||||
|
||||
@ -457,9 +457,9 @@
|
||||
|
||||
// Horizontal offset of the universal joints on the carriages.
|
||||
#define DELTA_CARRIAGE_OFFSET 22.0 // mm
|
||||
*/
|
||||
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS 104 //mm // get this value from auto calibrate
|
||||
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET - DELTA_EFFECTOR_OFFSET - DELTA_CARRIAGE_OFFSET) //mm // get this value from auto calibrate
|
||||
|
||||
// height from z=0.00 to home position
|
||||
#define DELTA_HEIGHT 280 // get this value from auto calibrate - use G33 C-1 at 1st time calibration
|
||||
@ -470,30 +470,30 @@
|
||||
// Delta calibration menu
|
||||
// uncomment to add three points calibration menu option.
|
||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||
#define DELTA_CALIBRATION_MENU
|
||||
//#define DELTA_CALIBRATION_MENU
|
||||
|
||||
// set the radius for the calibration probe points - max 0.8 * DELTA_PRINTABLE_RADIUS if DELTA_AUTO_CALIBRATION enabled
|
||||
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 17) // mm
|
||||
|
||||
// G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
|
||||
#define DELTA_AUTO_CALIBRATION
|
||||
//#define DELTA_AUTO_CALIBRATION
|
||||
#if ENABLED(DELTA_AUTO_CALIBRATION)
|
||||
#define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (-7 -> +7)
|
||||
#endif
|
||||
|
||||
// After homing move down to a height where XY movement is unconstrained
|
||||
#define DELTA_HOME_TO_SAFE_ZONE
|
||||
//#define DELTA_HOME_TO_SAFE_ZONE
|
||||
|
||||
#define DELTA_ENDSTOP_ADJ { -0.00, -0.00, -0.00 } // get these from auto calibrate
|
||||
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// Trim adjustments for individual towers
|
||||
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
|
||||
// measured in degrees anticlockwise looking from above the printer
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0.00, 0.00 } // get these from auto calibrate
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// delta radius and diaginal rod adjustments measured in mm
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0, 0, 0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
@ -438,7 +438,7 @@
|
||||
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 250.0 // mm
|
||||
/*
|
||||
|
||||
// Horizontal offset from middle of printer to smooth rod center.
|
||||
#define DELTA_SMOOTH_ROD_OFFSET 175.0 // mm
|
||||
|
||||
@ -447,9 +447,11 @@
|
||||
|
||||
// Horizontal offset of the universal joints on the carriages.
|
||||
#define DELTA_CARRIAGE_OFFSET 18.0 // mm
|
||||
*/
|
||||
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS 125 //mm // get this value from auto calibrate // height from z=0.00 to home position
|
||||
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET - DELTA_EFFECTOR_OFFSET - DELTA_CARRIAGE_OFFSET) //mm // get this value from auto calibrate // height from z=0.00 to home position
|
||||
|
||||
// height from z=0.00 to home position
|
||||
#define DELTA_HEIGHT 250 // get this value from auto calibrate - use G33 C-1 at 1st time calibration
|
||||
|
||||
// Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
|
||||
@ -457,30 +459,30 @@
|
||||
|
||||
// Delta calibration menu
|
||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||
#define DELTA_CALIBRATION_MENU
|
||||
//#define DELTA_CALIBRATION_MENU
|
||||
|
||||
// set the radius for the calibration probe points - max 0.8 * DELTA_PRINTABLE_RADIUS if DELTA_AUTO_CALIBRATION enabled
|
||||
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 28) // mm
|
||||
|
||||
// G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
|
||||
#define DELTA_AUTO_CALIBRATION
|
||||
//#define DELTA_AUTO_CALIBRATION
|
||||
#if ENABLED(DELTA_AUTO_CALIBRATION)
|
||||
#define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (-7 -> +7)
|
||||
#endif
|
||||
|
||||
// After homing move down to a height where XY movement is unconstrained
|
||||
#define DELTA_HOME_TO_SAFE_ZONE
|
||||
//#define DELTA_HOME_TO_SAFE_ZONE
|
||||
|
||||
#define DELTA_ENDSTOP_ADJ { -0.00, -0.00, -0.00 } // get these from auto calibrate
|
||||
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// Trim adjustments for individual towers
|
||||
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
|
||||
// measured in degrees anticlockwise looking from above the printer
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0.00, 0.00 } // get these from auto calibrate
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// delta radius and diaginal rod adjustments measured in mm
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0, 0, 0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
@ -438,7 +438,7 @@
|
||||
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 215.0 // mm
|
||||
/*
|
||||
|
||||
// Horizontal offset from middle of printer to smooth rod center.
|
||||
#define DELTA_SMOOTH_ROD_OFFSET 145.0 // mm
|
||||
|
||||
@ -447,9 +447,9 @@
|
||||
|
||||
// Horizontal offset of the universal joints on the carriages.
|
||||
#define DELTA_CARRIAGE_OFFSET 19.5 // mm
|
||||
*/
|
||||
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS 105 //mm // get this value from auto calibrate
|
||||
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET - DELTA_EFFECTOR_OFFSET - DELTA_CARRIAGE_OFFSET) //mm // get this value from auto calibrate
|
||||
|
||||
// height from z=0.00 to home position
|
||||
#define DELTA_HEIGHT 250 // get this value from auto calibrate - use G33 C-1 at 1st time calibration
|
||||
@ -459,30 +459,30 @@
|
||||
|
||||
// Delta calibration menu
|
||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||
#define DELTA_CALIBRATION_MENU
|
||||
//#define DELTA_CALIBRATION_MENU
|
||||
|
||||
// set the radius for the calibration probe points - max 0.8 * DELTA_PRINTABLE_RADIUS if DELTA_AUTO_CALIBRATION enabled
|
||||
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 18) // mm
|
||||
|
||||
// G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
|
||||
#define DELTA_AUTO_CALIBRATION
|
||||
//#define DELTA_AUTO_CALIBRATION
|
||||
#if ENABLED(DELTA_AUTO_CALIBRATION)
|
||||
#define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (-7 -> +7)
|
||||
#endif
|
||||
|
||||
// After homing move down to a height where XY movement is unconstrained
|
||||
#define DELTA_HOME_TO_SAFE_ZONE
|
||||
//#define DELTA_HOME_TO_SAFE_ZONE
|
||||
|
||||
#define DELTA_ENDSTOP_ADJ { -0.00, -0.00, -0.00 } // get these from auto calibrate
|
||||
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// Trim adjustments for individual towers
|
||||
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
|
||||
// measured in degrees anticlockwise looking from above the printer
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0.00, 0.00 } // get these from auto calibrate
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// delta radius and diaginal rod adjustments measured in mm
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0, 0, 0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
@ -425,7 +425,7 @@
|
||||
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 301.0 // mm
|
||||
/*
|
||||
|
||||
// Horizontal offset from middle of printer to smooth rod center.
|
||||
#define DELTA_SMOOTH_ROD_OFFSET 212.357 // mm
|
||||
|
||||
@ -434,9 +434,9 @@
|
||||
|
||||
// Horizontal offset of the universal joints on the carriages.
|
||||
#define DELTA_CARRIAGE_OFFSET 30.0 // mm
|
||||
*/
|
||||
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS 150 //mm // get this value from auto calibrate
|
||||
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET - DELTA_EFFECTOR_OFFSET - DELTA_CARRIAGE_OFFSET) //mm // get this value from auto calibrate
|
||||
|
||||
// height from z=0.00 to home position
|
||||
#define DELTA_HEIGHT 277 // get this value from auto calibrate - use G33 C-1 at 1st time calibration
|
||||
@ -446,30 +446,30 @@
|
||||
|
||||
// Delta calibration menu
|
||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||
#define DELTA_CALIBRATION_MENU
|
||||
//#define DELTA_CALIBRATION_MENU
|
||||
|
||||
// set the radius for the calibration probe points - max 0.8 * DELTA_PRINTABLE_RADIUS if DELTA_AUTO_CALIBRATION enabled
|
||||
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 25.4) // mm
|
||||
|
||||
// G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
|
||||
#define DELTA_AUTO_CALIBRATION
|
||||
//#define DELTA_AUTO_CALIBRATION
|
||||
#if ENABLED(DELTA_AUTO_CALIBRATION)
|
||||
#define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (-7 -> +7)
|
||||
#endif
|
||||
|
||||
// After homing move down to a height where XY movement is unconstrained
|
||||
#define DELTA_HOME_TO_SAFE_ZONE
|
||||
//#define DELTA_HOME_TO_SAFE_ZONE
|
||||
|
||||
#define DELTA_ENDSTOP_ADJ { -0.00, -0.00, -0.00 } // get these from auto calibrate
|
||||
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// Trim adjustments for individual towers
|
||||
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
|
||||
// measured in degrees anticlockwise looking from above the printer
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0.00, 0.00 } // get these from auto calibrate
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// delta radius and diaginal rod adjustments measured in mm
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0, 0, 0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
@ -443,7 +443,7 @@
|
||||
|
||||
// Center-to-center distance of the holes in the diagonal push rods.
|
||||
#define DELTA_DIAGONAL_ROD 317.3 + 2.5 // mm
|
||||
/*
|
||||
|
||||
// Horizontal offset from middle of printer to smooth rod center.
|
||||
#define DELTA_SMOOTH_ROD_OFFSET 220.1 // mm
|
||||
|
||||
@ -452,9 +452,9 @@
|
||||
|
||||
// Horizontal offset of the universal joints on the carriages.
|
||||
#define DELTA_CARRIAGE_OFFSET 22.0 // mm
|
||||
*/
|
||||
|
||||
// Horizontal distance bridged by diagonal push rods when effector is centered.
|
||||
#define DELTA_RADIUS 175 //mm // get this value from auto calibrate
|
||||
#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET - DELTA_EFFECTOR_OFFSET - DELTA_CARRIAGE_OFFSET) //mm // get this value from auto calibrate
|
||||
|
||||
// height from z=0.00 to home position
|
||||
#define DELTA_HEIGHT 380 // get this value from auto calibrate - use G33 C-1 at 1st time calibration
|
||||
@ -464,30 +464,30 @@
|
||||
|
||||
// Delta calibration menu
|
||||
// See http://minow.blogspot.com/index.html#4918805519571907051
|
||||
#define DELTA_CALIBRATION_MENU
|
||||
//#define DELTA_CALIBRATION_MENU
|
||||
|
||||
// set the radius for the calibration probe points - max 0.8 * DELTA_PRINTABLE_RADIUS if DELTA_AUTO_CALIBRATION enabled
|
||||
#define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - 28) // mm
|
||||
|
||||
// G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
|
||||
#define DELTA_AUTO_CALIBRATION
|
||||
//#define DELTA_AUTO_CALIBRATION
|
||||
#if ENABLED(DELTA_AUTO_CALIBRATION)
|
||||
#define DELTA_CALIBRATION_DEFAULT_POINTS 3 // set the default number of probe points : n*n (-7 -> +7)
|
||||
#endif
|
||||
|
||||
// After homing move down to a height where XY movement is unconstrained
|
||||
#define DELTA_HOME_TO_SAFE_ZONE
|
||||
//#define DELTA_HOME_TO_SAFE_ZONE
|
||||
|
||||
#define DELTA_ENDSTOP_ADJ { -0.00, -0.00, -0.00 } // get these from auto calibrate
|
||||
#define DELTA_ENDSTOP_ADJ { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// Trim adjustments for individual towers
|
||||
// tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
|
||||
// measured in degrees anticlockwise looking from above the printer
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0.00, 0.00 } // get these from auto calibrate
|
||||
#define DELTA_TOWER_ANGLE_TRIM { 0, 0, 0 } // get these from auto calibrate
|
||||
|
||||
// delta radius and diaginal rod adjustments measured in mm
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0.0, 0.0, 0.0}
|
||||
//#define DELTA_RADIUS_TRIM_TOWER {0, 0, 0}
|
||||
//#define DELTA_DIAGONAL_ROD_TRIM_TOWER {0, 0, 0}
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
Reference in New Issue
Block a user