Split up pins to make it more manageable
Hopefully this is helpful to organization and future expansion….
This commit is contained in:
88
Marlin/pins_PRINTRBOARD.h
Normal file
88
Marlin/pins_PRINTRBOARD.h
Normal file
@ -0,0 +1,88 @@
|
||||
/**
|
||||
* Printrboard pin assignments (AT90USB1286)
|
||||
* Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
|
||||
* http://www.pjrc.com/teensy/teensyduino.html
|
||||
* See http://reprap.org/wiki/Printrboard for more info
|
||||
*/
|
||||
|
||||
#ifndef __AVR_AT90USB1286__
|
||||
#error Oops! Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
|
||||
#endif
|
||||
|
||||
#ifdef AT90USBxx_TEENSYPP_ASSIGNMENTS // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional.
|
||||
#error These Printrboard assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h
|
||||
#endif
|
||||
|
||||
#define AT90USB 1286 // Disable MarlinSerial etc.
|
||||
|
||||
#define LARGE_FLASH true
|
||||
|
||||
#define X_STEP_PIN 0
|
||||
#define X_DIR_PIN 1
|
||||
#define X_ENABLE_PIN 39
|
||||
|
||||
#define Y_STEP_PIN 2
|
||||
#define Y_DIR_PIN 3
|
||||
#define Y_ENABLE_PIN 38
|
||||
|
||||
#define Z_STEP_PIN 4
|
||||
#define Z_DIR_PIN 5
|
||||
#define Z_ENABLE_PIN 23
|
||||
|
||||
#define E0_STEP_PIN 6
|
||||
#define E0_DIR_PIN 7
|
||||
#define E0_ENABLE_PIN 19
|
||||
|
||||
#define HEATER_0_PIN 21 // Extruder
|
||||
#define HEATER_1_PIN 46
|
||||
#define HEATER_2_PIN 47
|
||||
#define HEATER_BED_PIN 20
|
||||
|
||||
// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin
|
||||
// fastio pin numbering otherwise
|
||||
#ifdef FAN_SOFT_PWM || FAST_PWM_FAN
|
||||
#define FAN_PIN 22
|
||||
#else
|
||||
#define FAN_PIN 16
|
||||
#endif
|
||||
|
||||
#define X_STOP_PIN 35
|
||||
#define Y_STOP_PIN 8
|
||||
#define Z_STOP_PIN 36
|
||||
#define TEMP_0_PIN 1 // Extruder / Analog pin numbering
|
||||
#define TEMP_BED_PIN 0 // Bed / Analog pin numbering
|
||||
|
||||
#ifdef FILAMENT_SENSOR
|
||||
#define FILWIDTH_PIN 2
|
||||
#endif
|
||||
|
||||
#define TEMP_1_PIN -1
|
||||
#define TEMP_2_PIN -1
|
||||
|
||||
#define SDPOWER -1
|
||||
#define SDSS 8
|
||||
#define LED_PIN -1
|
||||
#define PS_ON_PIN -1
|
||||
#define KILL_PIN -1
|
||||
#define ALARM_PIN -1
|
||||
|
||||
#ifndef SDSUPPORT
|
||||
// these pins are defined in the SD library if building with SD support
|
||||
#define SCK_PIN 9
|
||||
#define MISO_PIN 11
|
||||
#define MOSI_PIN 10
|
||||
#endif
|
||||
|
||||
#if defined(ULTRA_LCD) && defined(NEWPANEL)
|
||||
//we have no buzzer installed
|
||||
#define BEEPER -1
|
||||
//LCD Pins
|
||||
#ifdef LCD_I2C_PANELOLU2
|
||||
#define BTN_EN1 27 //RX1 - fastio.h pin mapping 27
|
||||
#define BTN_EN2 26 //TX1 - fastio.h pin mapping 26
|
||||
#define BTN_ENC 43 //A3 - fastio.h pin mapping 43
|
||||
#define SDSS 40 //use SD card on Panelolu2 (Teensyduino pin mapping)
|
||||
#endif // LCD_I2C_PANELOLU2
|
||||
//not connected to a pin
|
||||
#define SDCARDDETECT -1
|
||||
#endif // ULTRA_LCD && NEWPANEL
|
Reference in New Issue
Block a user