✨ MKS SKIPR board (#24791)
This commit is contained in:
EvilGremlin
committed by
Scott Lahteine
Scott Lahteine
parent
62b7db9bb7
commit
505f0a647e
@ -425,6 +425,7 @@
|
||||
#define BOARD_CREALITY_V24S1_301F4 4240 // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4
|
||||
#define BOARD_OPULO_LUMEN_REV4 4241 // Opulo Lumen PnP Controller REV4 (STM32F407VE / STM32F407VG)
|
||||
#define BOARD_FYSETC_SPIDER_KING407 4242 // FYSETC Spider King407 (STM32F407ZG)
|
||||
#define BOARD_MKS_SKIPR_V1 4243 // MKS SKIPR v1.0 all-in-one board (STM32F407VE)
|
||||
|
||||
//
|
||||
// ARM Cortex M7
|
||||
|
||||
@ -709,6 +709,8 @@
|
||||
#include "stm32f4/pins_OPULO_LUMEN_REV4.h" // STM32F4 env:Opulo_Lumen_REV4
|
||||
#elif MB(FYSETC_SPIDER_KING407)
|
||||
#include "stm32f4/pins_FYSETC_SPIDER_KING407.h" // STM32F4 env:FYSETC_SPIDER_KING407
|
||||
#elif MB(MKS_SKIPR_V1)
|
||||
#include "stm32f4/pins_MKS_SKIPR_V1_0.h" // STM32F4 env:mks_skipr_v1 env:mks_skipr_v1_nobootloader
|
||||
|
||||
//
|
||||
// ARM Cortex M7
|
||||
|
||||
381
Marlin/src/pins/stm32f4/pins_MKS_SKIPR_V1_0.h
Normal file
381
Marlin/src/pins/stm32f4/pins_MKS_SKIPR_V1_0.h
Normal file
@ -0,0 +1,381 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
#include "env_validate.h"
|
||||
|
||||
#if HOTENDS > 4 || E_STEPPERS > 4
|
||||
#error "MKS SKIPR supports up to 4 hotends / E steppers."
|
||||
#endif
|
||||
|
||||
#define BOARD_INFO_NAME "MKS SKIPR V1.0"
|
||||
|
||||
// Valid SERIAL_PORT values: -1 (USB-C), 1 (direct to RK3328), 3 (USART3 header)
|
||||
|
||||
#define USES_DIAG_JUMPERS
|
||||
|
||||
// Onboard I2C EEPROM
|
||||
#define I2C_EEPROM
|
||||
#define MARLIN_EEPROM_SIZE 0x1000 // 4KB (AT24C32)
|
||||
#define I2C_SCL_PIN PB8
|
||||
#define I2C_SDA_PIN PB9
|
||||
|
||||
//
|
||||
// Servos
|
||||
//
|
||||
#define SERVO0_PIN PA8
|
||||
|
||||
//
|
||||
// Trinamic Stallguard pins // Connector labels
|
||||
#define X_DIAG_PIN PA14 // X-
|
||||
#define Y_DIAG_PIN PA15 // Y-
|
||||
#define Z_DIAG_PIN PB15 // Z-
|
||||
#define E0_DIAG_PIN PA13 // MT-DET
|
||||
#define E1_DIAG_PIN PC5 // NEOPIXEL
|
||||
#define E2_DIAG_PIN PB14 // Z+
|
||||
|
||||
//
|
||||
// Check for additional used endstop pins
|
||||
//
|
||||
#if HAS_EXTRA_ENDSTOPS
|
||||
#define _ENDSTOP_IS_ANY(ES) X2_USE_ENDSTOP == ES || Y2_USE_ENDSTOP == ES || Z2_USE_ENDSTOP == ES || Z3_USE_ENDSTOP == ES || Z4_USE_ENDSTOP == ES
|
||||
#if _ENDSTOP_IS_ANY(_XMIN_) || _ENDSTOP_IS_ANY(_XMAX_)
|
||||
#define NEEDS_X_MINMAX 1
|
||||
#endif
|
||||
#if _ENDSTOP_IS_ANY(_YMIN_) || _ENDSTOP_IS_ANY(_YMAX_)
|
||||
#define NEEDS_Y_MINMAX 1
|
||||
#endif
|
||||
#if _ENDSTOP_IS_ANY(_ZMIN_) || _ENDSTOP_IS_ANY(_ZMAX_)
|
||||
#define NEEDS_Z_MINMAX 1
|
||||
#endif
|
||||
#undef _ENDSTOP_IS_ANY
|
||||
#endif
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#ifdef X_STALL_SENSITIVITY
|
||||
#define X_STOP_PIN X_DIAG_PIN // X-
|
||||
#elif EITHER(DUAL_X_CARRIAGE, NEEDS_X_MINMAX)
|
||||
#ifndef X_MIN_PIN
|
||||
#define X_MIN_PIN X_DIAG_PIN // X-
|
||||
#endif
|
||||
#ifndef X_MAX_PIN
|
||||
#define X_MAX_PIN E0_DIAG_PIN // MT-DET
|
||||
#endif
|
||||
#else
|
||||
#define X_STOP_PIN X_DIAG_PIN // X-
|
||||
#endif
|
||||
|
||||
#ifdef Y_STALL_SENSITIVITY
|
||||
#define Y_STOP_PIN Y_DIAG_PIN // Y-
|
||||
#elif NEEDS_Y_MINMAX
|
||||
#ifndef Y_MIN_PIN
|
||||
#define Y_MIN_PIN Y_DIAG_PIN // Y-
|
||||
#endif
|
||||
#ifndef Y_MAX_PIN
|
||||
#define Y_MAX_PIN E1_DIAG_PIN // NEOPIXEL
|
||||
#endif
|
||||
#else
|
||||
#define Y_STOP_PIN Y_DIAG_PIN // Y-
|
||||
#endif
|
||||
|
||||
#ifdef Z_STALL_SENSITIVITY
|
||||
#define Z_STOP_PIN Z_DIAG_PIN // Z-
|
||||
#elif NEEDS_Z_MINMAX
|
||||
#ifndef Z_MIN_PIN
|
||||
#define Z_MIN_PIN Z_DIAG_PIN // Z-
|
||||
#endif
|
||||
#ifndef Z_MAX_PIN
|
||||
#define Z_MAX_PIN E2_DIAG_PIN // Z+
|
||||
#endif
|
||||
#else
|
||||
#define Z_STOP_PIN Z_DIAG_PIN // Z-
|
||||
#endif
|
||||
|
||||
#if DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) || ENABLED(USE_PROBE_FOR_Z_HOMING)
|
||||
#ifndef Z_MIN_PROBE
|
||||
#define Z_MIN_PROBE_PIN E2_DIAG_PIN // defaults to 'Z+' connector
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#undef NEEDS_X_MINMAX
|
||||
#undef NEEDS_Y_MINMAX
|
||||
#undef NEEDS_Z_MINMAX
|
||||
|
||||
//
|
||||
// Steppers
|
||||
//
|
||||
#define X_STEP_PIN PC14
|
||||
#define X_DIR_PIN PC13
|
||||
#define X_ENABLE_PIN PC15
|
||||
#ifndef X_CS_PIN
|
||||
#define X_CS_PIN PE6
|
||||
#endif
|
||||
|
||||
#define Y_STEP_PIN PE5
|
||||
#define Y_DIR_PIN PE4
|
||||
#define Y_ENABLE_PIN PD14
|
||||
#ifndef Y_CS_PIN
|
||||
#define Y_CS_PIN PE3
|
||||
#endif
|
||||
|
||||
#define Z_STEP_PIN PE1 // "Z1"
|
||||
#define Z_DIR_PIN PE0
|
||||
#define Z_ENABLE_PIN PE2
|
||||
#ifndef Z_CS_PIN
|
||||
#define Z_CS_PIN PB7
|
||||
#endif
|
||||
|
||||
#define E0_STEP_PIN PB5
|
||||
#define E0_DIR_PIN PB4
|
||||
#define E0_ENABLE_PIN PB6
|
||||
#ifndef E0_CS_PIN
|
||||
#define E0_CS_PIN PB3
|
||||
#endif
|
||||
|
||||
#define E1_STEP_PIN PD6 // "Z2"
|
||||
#define E1_DIR_PIN PD5
|
||||
#define E1_ENABLE_PIN PD7
|
||||
#ifndef E1_CS_PIN
|
||||
#define E1_CS_PIN PD4
|
||||
#endif
|
||||
|
||||
#define E2_STEP_PIN PD2 // "Z3"
|
||||
#define E2_DIR_PIN PD1
|
||||
#define E2_ENABLE_PIN PD3
|
||||
#ifndef E2_CS_PIN
|
||||
#define E2_CS_PIN PD0
|
||||
#endif
|
||||
|
||||
#define E3_STEP_PIN PC7 // "Z4"
|
||||
#define E3_DIR_PIN PC6
|
||||
#define E3_ENABLE_PIN PC8
|
||||
#ifndef E3_CS_PIN
|
||||
#define E3_CS_PIN PD15
|
||||
#endif
|
||||
|
||||
//
|
||||
// Temperature Sensors
|
||||
//
|
||||
#define TEMP_BED_PIN PC0 // TB
|
||||
#define TEMP_0_PIN PC1 // TH0
|
||||
#define TEMP_1_PIN PC2 // TH1
|
||||
#define TEMP_2_PIN PC3 // TH2
|
||||
|
||||
//
|
||||
// Heaters / Fans
|
||||
//
|
||||
#define HEATER_BED_PIN PD12 // Hotbed
|
||||
#define HEATER_0_PIN PB1 // Heater0
|
||||
#define HEATER_1_PIN PB0 // Heater1
|
||||
#define HEATER_2_PIN PA3 // Heater2
|
||||
|
||||
#define FAN_PIN PA2 // Fan0
|
||||
#define FAN1_PIN PA1 // Fan1
|
||||
#define FAN2_PIN PA0 // Fan2
|
||||
|
||||
//
|
||||
// Software SPI pins for TMC2130 stepper drivers
|
||||
// This board doesn't support hardware SPI there
|
||||
//
|
||||
#if HAS_TMC_SPI
|
||||
#define TMC_USE_SW_SPI
|
||||
#define TMC_SW_MOSI PE14
|
||||
#define TMC_SW_MISO PE13
|
||||
#define TMC_SW_SCK PE12
|
||||
#endif
|
||||
|
||||
//
|
||||
// TMC2208/TMC2209 stepper drivers
|
||||
// This board is routed for one-wire software serial
|
||||
//
|
||||
#if HAS_TMC_UART
|
||||
#define X_SERIAL_TX_PIN PE6
|
||||
#define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
|
||||
|
||||
#define Y_SERIAL_TX_PIN PE3
|
||||
#define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
|
||||
|
||||
#define Z_SERIAL_TX_PIN PB7
|
||||
#define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
|
||||
|
||||
#define E0_SERIAL_TX_PIN PB3
|
||||
#define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
|
||||
|
||||
#define E1_SERIAL_TX_PIN PD4
|
||||
#define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN
|
||||
|
||||
#define E2_SERIAL_TX_PIN PD0
|
||||
#define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN
|
||||
|
||||
#define E3_SERIAL_TX_PIN PD15
|
||||
#define E3_SERIAL_RX_PIN E3_SERIAL_TX_PIN
|
||||
|
||||
// Reduce baud rate to improve software serial reliability
|
||||
#define TMC_BAUD_RATE 19200
|
||||
#endif
|
||||
|
||||
/** ------ ------
|
||||
* (BEEPER) PB2 | 1 2 | PE10 (BTN_ENC) (MISO) PA6 | 1 2 | PA5 (SCK)
|
||||
* (LCD_EN) PE11 | 3 4 | PD10 (LCD_RS) (BTN_EN1) PE9 | 3 4 | PA4 (SD_SS)
|
||||
* (LCD_D4) PD9 | 5 6 PD8 (LCD_D5) (BTN_EN2) PE8 | 5 6 PA7 (MOSI)
|
||||
* (LCD_D6) PE15 | 7 8 | PE7 (LCD_D7) (SD_DETECT) PD13 | 7 8 | RESET
|
||||
* GND | 9 10 | 5V GND | 9 10 | --
|
||||
* ------ ------
|
||||
* EXP1 EXP2
|
||||
*/
|
||||
#define EXP1_01_PIN PB2
|
||||
#define EXP1_02_PIN PE10
|
||||
#define EXP1_03_PIN PE11
|
||||
#define EXP1_04_PIN PD10
|
||||
#define EXP1_05_PIN PD9
|
||||
#define EXP1_06_PIN PD8
|
||||
#define EXP1_07_PIN PE15
|
||||
#define EXP1_08_PIN PE7
|
||||
|
||||
#define EXP2_01_PIN PA6
|
||||
#define EXP2_02_PIN PA5
|
||||
#define EXP2_03_PIN PE9
|
||||
#define EXP2_04_PIN PA4
|
||||
#define EXP2_05_PIN PE8
|
||||
#define EXP2_06_PIN PA7
|
||||
#define EXP2_07_PIN PD13
|
||||
#define EXP2_08_PIN -1 // connected to MCU reset
|
||||
|
||||
//
|
||||
// SD Support
|
||||
// Onboard SD card use hardware SPI3 (defined in variant), LCD SD card use hardware SPI1
|
||||
//
|
||||
#if ENABLED(SDSUPPORT)
|
||||
#ifndef SDCARD_CONNECTION
|
||||
#define SDCARD_CONNECTION LCD
|
||||
#endif
|
||||
#if SD_CONNECTION_IS(ONBOARD)
|
||||
//#define SOFTWARE_SPI
|
||||
//#define SD_SPI_SPEED SPI_HALF_SPEED
|
||||
#undef SD_DETECT_STATE
|
||||
#define SD_DETECT_STATE LOW
|
||||
#define SD_DETECT_PIN PC4
|
||||
#elif SD_CONNECTION_IS(LCD)
|
||||
//#define SOFTWARE_SPI
|
||||
//#define SD_SPI_SPEED SPI_QUARTER_SPEED
|
||||
#define SD_SS_PIN EXP2_04_PIN
|
||||
#define SD_SCK_PIN EXP2_02_PIN
|
||||
#define SD_MISO_PIN EXP2_01_PIN
|
||||
#define SD_MOSI_PIN EXP2_06_PIN
|
||||
#define SD_DETECT_PIN EXP2_07_PIN
|
||||
#elif SD_CONNECTION_IS(CUSTOM_CABLE)
|
||||
#error "CUSTOM_CABLE is not a supported SDCARD_CONNECTION for this board"
|
||||
#endif
|
||||
#define SDSS SD_SS_PIN
|
||||
#endif
|
||||
|
||||
//
|
||||
// LCDs and Controllers
|
||||
//
|
||||
#if IS_TFTGLCD_PANEL
|
||||
|
||||
#if ENABLED(TFTGLCD_PANEL_SPI)
|
||||
#define TFTGLCD_CS EXP2_03_PIN
|
||||
#endif
|
||||
|
||||
#elif HAS_WIRED_LCD
|
||||
|
||||
#define BEEPER_PIN EXP1_01_PIN
|
||||
#define BTN_ENC EXP1_02_PIN
|
||||
|
||||
#if ENABLED(CR10_STOCKDISPLAY)
|
||||
|
||||
#define LCD_PINS_RS EXP1_07_PIN
|
||||
|
||||
#define BTN_EN1 EXP1_03_PIN
|
||||
#define BTN_EN2 EXP1_05_PIN
|
||||
|
||||
#define LCD_PINS_ENABLE EXP1_08_PIN
|
||||
#define LCD_PINS_D4 EXP1_06_PIN
|
||||
|
||||
#else
|
||||
|
||||
#define LCD_PINS_RS EXP1_04_PIN
|
||||
|
||||
#define BTN_EN1 EXP2_03_PIN
|
||||
#define BTN_EN2 EXP2_05_PIN
|
||||
|
||||
#define LCD_PINS_ENABLE EXP1_03_PIN
|
||||
#define LCD_PINS_D4 EXP1_05_PIN
|
||||
|
||||
#if ENABLED(FYSETC_MINI_12864)
|
||||
#define DOGLCD_CS EXP1_03_PIN
|
||||
#define DOGLCD_A0 EXP1_04_PIN
|
||||
//#define LCD_BACKLIGHT_PIN -1
|
||||
#define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally.
|
||||
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
||||
#ifndef RGB_LED_R_PIN
|
||||
#define RGB_LED_R_PIN EXP1_06_PIN
|
||||
#endif
|
||||
#ifndef RGB_LED_G_PIN
|
||||
#define RGB_LED_G_PIN EXP1_07_PIN
|
||||
#endif
|
||||
#ifndef RGB_LED_B_PIN
|
||||
#define RGB_LED_B_PIN EXP1_08_PIN
|
||||
#endif
|
||||
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
||||
#define NEOPIXEL_PIN EXP1_06_PIN
|
||||
#endif
|
||||
#endif // !FYSETC_MINI_12864
|
||||
|
||||
#if IS_ULTIPANEL
|
||||
#define LCD_PINS_D5 EXP1_06_PIN
|
||||
#define LCD_PINS_D6 EXP1_07_PIN
|
||||
#define LCD_PINS_D7 EXP1_08_PIN
|
||||
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
||||
#define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#endif
|
||||
#endif // HAS_WIRED_LCD
|
||||
|
||||
// Alter timing for graphical display
|
||||
#if IS_U8GLIB_ST7920
|
||||
#define BOARD_ST7920_DELAY_1 120
|
||||
#define BOARD_ST7920_DELAY_2 80
|
||||
#define BOARD_ST7920_DELAY_3 580
|
||||
#endif
|
||||
|
||||
//
|
||||
// NeoPixel LED
|
||||
//
|
||||
#ifndef NEOPIXEL_PIN
|
||||
#define NEOPIXEL_PIN PC5
|
||||
#endif
|
||||
|
||||
//
|
||||
// MAX31865
|
||||
//
|
||||
#if HAS_MAX31865
|
||||
#define TEMP_0_CS_PIN PD11
|
||||
#define TEMP_0_SCK_PIN PE12
|
||||
#define TEMP_0_MISO_PIN PE13
|
||||
#define TEMP_0_MOSI_PIN PE14
|
||||
#endif
|
||||
Reference in New Issue
Block a user