Merge pull request #8074 from thinkyhead/bf2_verbiage_like_8061

Fix some config verbiage
This commit is contained in:
Scott Lahteine 2017-10-24 15:25:12 -05:00 committed by GitHub
commit 46aae4c6e7
41 changed files with 741 additions and 732 deletions

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1630,17 +1630,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1656,10 +1656,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1679,18 +1679,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1769,17 +1769,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1795,10 +1795,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1818,18 +1818,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1618,17 +1618,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1644,10 +1644,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1667,18 +1667,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1601,17 +1601,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1627,10 +1627,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1650,18 +1650,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1611,17 +1611,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1637,10 +1637,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1660,18 +1660,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1601,17 +1601,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1627,10 +1627,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1650,18 +1650,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1609,17 +1609,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1635,10 +1635,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1658,18 +1658,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1620,17 +1620,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1646,10 +1646,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1669,18 +1669,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1592,17 +1592,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1618,10 +1618,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1641,18 +1641,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1592,17 +1592,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1618,10 +1618,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1641,18 +1641,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1607,17 +1607,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1633,10 +1633,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1656,18 +1656,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
#define NUM_SERVOS 1 // Servo index starts with 0 for M280 command #define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1625,17 +1625,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1651,10 +1651,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1674,18 +1674,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
#define NUM_SERVOS 1 // Servo index starts with 0 for M280 command #define NUM_SERVOS 1 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1614,17 +1614,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1640,10 +1640,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1663,18 +1663,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1638,17 +1638,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1664,10 +1664,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1687,18 +1687,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1614,17 +1614,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle such current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
//#define RGB_LED //#define RGB_LED
@ -1640,10 +1640,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1663,18 +1663,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1614,17 +1614,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* The Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle such current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
//#define RGB_LED //#define RGB_LED
@ -1640,10 +1640,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequent display for temperature change - LED by LED. Comment out for change all LED at time #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1663,18 +1663,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1586,14 +1586,20 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* NOTE: A separate 5V power supply is required! The Neopixel LED needs
* more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED Type. Enable only one of the following two options.
*
*/ */
//#define RGB_LED //#define RGB_LED
//#define RGBW_LED //#define RGBW_LED
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED) #if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
@ -1604,10 +1610,13 @@
#endif #endif
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_RGBW_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_RGBW_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIXELS 3 #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1626,18 +1635,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1622,17 +1622,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1648,10 +1648,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1671,18 +1671,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1641,17 +1641,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1667,10 +1667,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1690,18 +1690,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1666,17 +1666,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1692,10 +1692,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1715,18 +1715,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1645,17 +1645,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1671,10 +1671,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1694,18 +1694,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1610,17 +1610,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1636,10 +1636,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1659,18 +1659,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1738,17 +1738,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1764,10 +1764,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1787,18 +1787,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1731,17 +1731,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1757,10 +1757,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1780,18 +1780,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1726,17 +1726,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1752,10 +1752,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1775,18 +1775,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1729,17 +1729,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1755,10 +1755,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1778,18 +1778,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1729,17 +1729,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1755,10 +1755,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1778,18 +1778,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1738,17 +1738,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1764,10 +1764,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1787,18 +1787,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1624,17 +1624,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1650,10 +1650,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1673,18 +1673,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
#define NUM_SERVOS 2 // Servo index starts with 0 for M280 command #define NUM_SERVOS 2 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1613,17 +1613,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1639,10 +1639,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1662,18 +1662,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1585,10 +1585,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1608,18 +1608,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1605,17 +1605,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1631,10 +1631,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1654,18 +1654,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.

View File

@ -1615,17 +1615,17 @@
* Adds the M150 command to set the LED (or LED strip) color. * Adds the M150 command to set the LED (or LED strip) color.
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
* luminance values can be set from 0 to 255. * luminance values can be set from 0 to 255.
* For Neopixel LED overall brightness parameters is also available * For Neopixel LED an overall brightness parameter is also available.
* *
* *** CAUTION *** * *** CAUTION ***
* LED Strips require a MOFSET Chip between PWM lines and LEDs, * LED Strips require a MOFSET Chip between PWM lines and LEDs,
* as the Arduino cannot handle the current the LEDs will require. * as the Arduino cannot handle the current the LEDs will require.
* Failure to follow this precaution can destroy your Arduino! * Failure to follow this precaution can destroy your Arduino!
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino * NOTE: A separate 5V power supply is required! The Neopixel LED needs
* cannot handle the current, separate 5V power supply must be used * more current than the Arduino 5V linear regulator can produce.
* *** CAUTION *** * *** CAUTION ***
* *
* LED type. This options are mutualy exclusive. Uncomment only one. * LED Type. Enable only one of the following two options.
* *
*/ */
@ -1641,10 +1641,10 @@
// Support for Adafruit Neopixel LED driver // Support for Adafruit Neopixel LED driver
//#define NEOPIXEL_LED //#define NEOPIXEL_LED
#if ENABLED(NEOPIXEL_LED) #if ENABLED(NEOPIXEL_LED)
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h) #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once. #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#endif #endif
@ -1664,18 +1664,18 @@
#define PRINTER_EVENT_LEDS #define PRINTER_EVENT_LEDS
#endif #endif
/*********************************************************************\ /**
* R/C SERVO support * R/C SERVO support
* Sponsored by TrinityLabs, Reworked by codexmas * Sponsored by TrinityLabs, Reworked by codexmas
**********************************************************************/ */
// Number of servos /**
// * Number of servos
// If you select a configuration below, this will receive a default value and does not need to be set manually *
// set it manually if you have more servos than extruders and wish to manually control some * For some servo-related options NUM_SERVOS will be set automatically.
// leaving it undefined or defining as 0 will disable the servo subsystem * Set this manually if there are extra servos needing manual control.
// If unsure, leave commented / disabled * Leave undefined or set to 0 to entirely disable the servo subsystem.
// */
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command //#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. // Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle.