Updated bq Hephestos 2 example configuration

Marlin/example_configurations/Hephestos_2/Configuration_adv.h

@@ -171,7 +171,7 @@
 // Extruder runout prevention.
 // If the machine is idle and the temperature over MINTEMP
 // then extrude some filament every couple of SECONDS.
-//#define EXTRUDER_RUNOUT_PREVENT
+#define EXTRUDER_RUNOUT_PREVENT
 #if ENABLED(EXTRUDER_RUNOUT_PREVENT)
   #define EXTRUDER_RUNOUT_MINTEMP 190
   #define EXTRUDER_RUNOUT_SECONDS 30
@@ -335,7 +335,7 @@
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2
 #define HOMING_BUMP_DIVISOR {2, 2, 4}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
-//#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
+#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
 
 // When G28 is called, this option will make Y home before X
 #define HOME_Y_BEFORE_X
@@ -369,7 +369,7 @@
 
 #if ENABLED(ULTIPANEL)
   #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
-  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+  //#define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
 #endif
 
 // @section extras
@@ -420,10 +420,10 @@
 // @section lcd
 
 // Include a page of printer information in the LCD Main Menu
-//#define LCD_INFO_MENU
+#define LCD_INFO_MENU
 
 // On the Info Screen, display XY with one decimal place when possible
-//#define LCD_DECIMAL_SMALL_XY
+#define LCD_DECIMAL_SMALL_XY
 
 #if ENABLED(SDSUPPORT)
 
@@ -440,7 +440,7 @@
   #define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the file system block order.
   // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
   // using:
-  #define MENU_ADDAUTOSTART
+  //#define MENU_ADDAUTOSTART
 
   // Show a progress bar on HD44780 LCDs for SD printing
   //#define LCD_PROGRESS_BAR
@@ -470,7 +470,7 @@
 #if ENABLED(DOGLCD)
   // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
-  //#define USE_BIG_EDIT_FONT
+  #define USE_BIG_EDIT_FONT
 
   // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
@@ -527,7 +527,7 @@
 //    interrupts (without LCD update). By enforcing a minimum time-per-move, the buffer is prevented from
 //    draining.
 //
-//#define ENSURE_SMOOTH_MOVES
+#define ENSURE_SMOOTH_MOVES
 #if ENABLED(ENSURE_SMOOTH_MOVES)
   //#define ALWAYS_ALLOW_MENU      // If enabled, the menu will always be responsive.
                                    // WARNING: Menu navigation during short moves may cause stuttering!
@@ -622,9 +622,9 @@
 // The number of linear motions that can be in the plan at any give time.
 // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
 #if ENABLED(SDSUPPORT)
-  #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
+  #define BLOCK_BUFFER_SIZE 32 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
 #else
-  #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+  #define BLOCK_BUFFER_SIZE 64 // maximize block buffer
 #endif
 
 // @section serial
@@ -640,7 +640,7 @@
 // For debug-echo: 128 bytes for the optimal speed.
 // Other output doesn't need to be that speedy.
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
-#define TX_BUFFER_SIZE 0
+#define TX_BUFFER_SIZE 32
 
 // Enable an emergency-command parser to intercept certain commands as they
 // enter the serial receive buffer, so they cannot be blocked.