Retire HAL for STM32F4 / F7 (#20153)
This commit is contained in:
Jason Smith
GitHub
@ -594,6 +594,8 @@
|
||||
#include "stm32f1/pins_FLY_MINI.h" // STM32F1 env:FLY_MINI
|
||||
#elif MB(FLSUN_HISPEED)
|
||||
#include "stm32f1/pins_FLSUN_HISPEED.h" // STM32F1 env:flsun_hispeed
|
||||
#elif MB(BEAST)
|
||||
#include "stm32f1/pins_BEAST.h" // STM32F1 env:STM32F103RE
|
||||
|
||||
//
|
||||
// ARM Cortex-M4F
|
||||
@ -608,10 +610,6 @@
|
||||
// STM32 ARM Cortex-M4F
|
||||
//
|
||||
|
||||
#elif MB(BEAST)
|
||||
#include "stm32f4/pins_BEAST.h" // STM32F4 env:STM32F4
|
||||
#elif MB(GENERIC_STM32F4)
|
||||
#include "stm32f4/pins_GENERIC_STM32F4.h" // STM32F4 env:STM32F4
|
||||
#elif MB(ARMED)
|
||||
#include "stm32f4/pins_ARMED.h" // STM32F4 env:ARMED
|
||||
#elif MB(RUMBA32_V1_0)
|
||||
@ -633,13 +631,13 @@
|
||||
#elif MB(BTT_BTT002_V1_0)
|
||||
#include "stm32f4/pins_BTT_BTT002_V1_0.h" // STM32F4 env:BIGTREE_BTT002
|
||||
#elif MB(LERDGE_K)
|
||||
#include "stm32f4/pins_LERDGE_K.h" // STM32F4 env:STM32F4
|
||||
#include "stm32f4/pins_LERDGE_K.h" // STM32F4 env:LERDGEK
|
||||
#elif MB(LERDGE_S)
|
||||
#include "stm32f4/pins_LERDGE_S.h" // STM32F4 env:LERDGE_S
|
||||
#include "stm32f4/pins_LERDGE_S.h" // STM32F4 env:LERDGES
|
||||
#elif MB(LERDGE_X)
|
||||
#include "stm32f4/pins_LERDGE_X.h" // STM32F4 env:LERDGE_X
|
||||
#include "stm32f4/pins_LERDGE_X.h" // STM32F4 env:LERDGEX
|
||||
#elif MB(VAKE403D)
|
||||
#include "stm32f4/pins_VAKE403D.h" // STM32F4 env:STM32F4
|
||||
#include "stm32f4/pins_VAKE403D.h" // STM32F4
|
||||
#elif MB(FYSETC_S6)
|
||||
#include "stm32f4/pins_FYSETC_S6.h" // STM32F4 env:FYSETC_S6
|
||||
#elif MB(FLYF407ZG)
|
||||
@ -653,10 +651,8 @@
|
||||
// ARM Cortex M7
|
||||
//
|
||||
|
||||
#elif MB(THE_BORG)
|
||||
#include "stm32f7/pins_THE_BORG.h" // STM32F7 env:STM32F7
|
||||
#elif MB(REMRAM_V1)
|
||||
#include "stm32f7/pins_REMRAM_V1.h" // STM32F7 env:STM32F7
|
||||
#include "stm32f7/pins_REMRAM_V1.h" // STM32F7 env:REMRAM_V1
|
||||
#elif MB(NUCLEO_F767ZI)
|
||||
#include "stm32f7/pins_NUCLEO_F767ZI.h" // STM32F7 env:NUCLEO_F767ZI
|
||||
#elif MB(TEENSY41)
|
||||
|
||||
@ -21,8 +21,8 @@
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
#if NOT_TARGET(__STM32F1__, __STM32F4__)
|
||||
#error "Oops! Select an STM32F1/4 board in 'Tools > Board.'"
|
||||
#if NOT_TARGET(__STM32F1__)
|
||||
#error "Oops! Select an STM32F1 board in 'Tools > Board.'"
|
||||
#endif
|
||||
|
||||
/**
|
||||
@ -1,197 +0,0 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
/**
|
||||
* To build with Arduino IDE use "Discovery F407VG"
|
||||
* To build with PlatformIO use environment "STM32F4"
|
||||
*/
|
||||
#if NOT_TARGET(STM32F4, STM32F4xx)
|
||||
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
|
||||
#elif HOTENDS > 2 || E_STEPPERS > 2
|
||||
#error "STM32F4 supports up to 2 hotends / E-steppers."
|
||||
#endif
|
||||
|
||||
#define BOARD_INFO_NAME "Misc. STM32F4"
|
||||
#define DEFAULT_MACHINE_NAME "STM32F407VET6"
|
||||
|
||||
//#define I2C_EEPROM
|
||||
|
||||
#ifndef MARLIN_EEPROM_SIZE
|
||||
#define MARLIN_EEPROM_SIZE 0x1000 // 4KB
|
||||
#endif
|
||||
|
||||
// Ignore temp readings during development.
|
||||
//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#define X_MIN_PIN PE0
|
||||
#define X_MAX_PIN -1
|
||||
#define Y_MIN_PIN PE1
|
||||
#define Y_MAX_PIN -1
|
||||
#define Z_MIN_PIN PE14
|
||||
#define Z_MAX_PIN -1
|
||||
|
||||
//
|
||||
// Z Probe (when not Z_MIN_PIN)
|
||||
//
|
||||
|
||||
//#ifndef Z_MIN_PROBE_PIN
|
||||
// #define Z_MIN_PROBE_PIN PA4
|
||||
//#endif
|
||||
|
||||
//
|
||||
// Steppers
|
||||
//
|
||||
|
||||
#define X_STEP_PIN PD3
|
||||
#define X_DIR_PIN PD2
|
||||
#define X_ENABLE_PIN PD0
|
||||
//#ifndef X_CS_PIN
|
||||
// #define X_CS_PIN PD1
|
||||
//#endif
|
||||
|
||||
#define Y_STEP_PIN PE11
|
||||
#define Y_DIR_PIN PE10
|
||||
#define Y_ENABLE_PIN PE13
|
||||
//#ifndef Y_CS_PIN
|
||||
// #define Y_CS_PIN PE12
|
||||
//#endif
|
||||
|
||||
#define Z_STEP_PIN PD6
|
||||
#define Z_DIR_PIN PD7
|
||||
#define Z_ENABLE_PIN PD4
|
||||
//#ifndef Z_CS_PIN
|
||||
// #define Z_CS_PIN PD5
|
||||
//#endif
|
||||
|
||||
#define E0_STEP_PIN PB5
|
||||
#define E0_DIR_PIN PB6
|
||||
#define E0_ENABLE_PIN PB3
|
||||
//#ifndef E0_CS_PIN
|
||||
// #define E0_CS_PIN PB4
|
||||
//#endif
|
||||
|
||||
#define E1_STEP_PIN PE4
|
||||
#define E1_DIR_PIN PE2
|
||||
#define E1_ENABLE_PIN PE3
|
||||
//#ifndef E1_CS_PIN
|
||||
// #define E1_CS_PIN PE5
|
||||
//#endif
|
||||
|
||||
#define SCK_PIN PA5
|
||||
#define MISO_PIN PA6
|
||||
#define MOSI_PIN PA7
|
||||
|
||||
//
|
||||
// Temperature Sensors
|
||||
//
|
||||
|
||||
#define TEMP_0_PIN PC0 // Analog Input
|
||||
#define TEMP_1_PIN PC1 // Analog Input
|
||||
#define TEMP_BED_PIN PC2 // Analog Input
|
||||
|
||||
//
|
||||
// Heaters / Fans
|
||||
//
|
||||
|
||||
#define HEATER_0_PIN PA1
|
||||
#define HEATER_1_PIN PA2
|
||||
#define HEATER_BED_PIN PA0
|
||||
|
||||
#ifndef FAN_PIN
|
||||
#define FAN_PIN PC6
|
||||
#endif
|
||||
#define FAN1_PIN PC7
|
||||
#define FAN2_PIN PC8
|
||||
|
||||
#ifndef E0_AUTO_FAN_PIN
|
||||
#define E0_AUTO_FAN_PIN PC7
|
||||
#endif
|
||||
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
|
||||
//#define CASE_LIGHT_PIN_CI PF13
|
||||
//#define CASE_LIGHT_PIN_DO PF14
|
||||
//#define NEOPIXEL_PIN PF13
|
||||
|
||||
//
|
||||
// Průša i3 MK2 Multi Material Multiplexer Support
|
||||
//
|
||||
|
||||
//#define E_MUX0_PIN PG3
|
||||
//#define E_MUX1_PIN PG4
|
||||
|
||||
//
|
||||
// Servos
|
||||
//
|
||||
|
||||
//#define SERVO0_PIN PE13
|
||||
//#define SERVO1_PIN PE14
|
||||
|
||||
#define SDSS PE7
|
||||
#define SS_PIN PE7
|
||||
#define LED_PIN PB7 //Alive
|
||||
#define PS_ON_PIN PA10
|
||||
#define KILL_PIN PA8
|
||||
#define PWR_LOSS PA4 //Power loss / nAC_FAULT
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
//
|
||||
|
||||
#define SD_DETECT_PIN PA15
|
||||
#define BEEPER_PIN PC9
|
||||
#define LCD_PINS_RS PE9
|
||||
#define LCD_PINS_ENABLE PE8
|
||||
#define LCD_PINS_D4 PB12
|
||||
#define LCD_PINS_D5 PB13
|
||||
#define LCD_PINS_D6 PB14
|
||||
#define LCD_PINS_D7 PB15
|
||||
#define BTN_EN1 PC4
|
||||
#define BTN_EN2 PC5
|
||||
#define BTN_ENC PC3
|
||||
|
||||
//
|
||||
// Filament runout
|
||||
//
|
||||
|
||||
#define FIL_RUNOUT_PIN PA3
|
||||
|
||||
//
|
||||
// ST7920 Delays
|
||||
//
|
||||
#if HAS_MARLINUI_U8GLIB
|
||||
#ifndef BOARD_ST7920_DELAY_1
|
||||
#define BOARD_ST7920_DELAY_1 DELAY_NS(96)
|
||||
#endif
|
||||
#ifndef BOARD_ST7920_DELAY_2
|
||||
#define BOARD_ST7920_DELAY_2 DELAY_NS(48)
|
||||
#endif
|
||||
#ifndef BOARD_ST7920_DELAY_3
|
||||
#define BOARD_ST7920_DELAY_3 DELAY_NS(715)
|
||||
#endif
|
||||
#endif
|
||||
@ -1,183 +0,0 @@
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||
*
|
||||
* Based on Sprinter and grbl.
|
||||
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
||||
*
|
||||
* This program is free software: you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License as published by
|
||||
* the Free Software Foundation, either version 3 of the License, or
|
||||
* (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License
|
||||
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
||||
*
|
||||
*/
|
||||
#pragma once
|
||||
|
||||
#if NOT_TARGET(STM32F7)
|
||||
#error "Oops! Select an STM32F7 board in 'Tools > Board.'"
|
||||
#elif HOTENDS > 3 || E_STEPPERS > 3
|
||||
#error "The-Borg supports up to 3 hotends / E-steppers."
|
||||
#endif
|
||||
|
||||
#define BOARD_INFO_NAME "The-Borge"
|
||||
#define DEFAULT_MACHINE_NAME BOARD_INFO_NAME
|
||||
|
||||
#ifndef MARLIN_EEPROM_SIZE
|
||||
#define MARLIN_EEPROM_SIZE 0x1000
|
||||
#endif
|
||||
|
||||
// Ignore temp readings during development.
|
||||
//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
#define X_MIN_PIN PE9
|
||||
#define X_MAX_PIN PE10
|
||||
#define Y_MIN_PIN PE7
|
||||
#define Y_MAX_PIN PE8
|
||||
#define Z_MIN_PIN PF15
|
||||
#define Z_MAX_PIN PG0
|
||||
#define E_MIN_PIN PE2
|
||||
#define E_MAX_PIN PE3
|
||||
|
||||
//
|
||||
// Z Probe (when not Z_MIN_PIN)
|
||||
//
|
||||
#ifndef Z_MIN_PROBE_PIN
|
||||
#define Z_MIN_PROBE_PIN PA4
|
||||
#endif
|
||||
|
||||
//
|
||||
// Steppers
|
||||
//
|
||||
#define STEPPER_ENABLE_PIN PE0
|
||||
|
||||
#define X_STEP_PIN PC6 // 96, 39 in Arduino
|
||||
#define X_DIR_PIN PC7
|
||||
#define X_ENABLE_PIN PC8
|
||||
|
||||
#define Y_STEP_PIN PD9
|
||||
#define Y_DIR_PIN PD10
|
||||
#define Y_ENABLE_PIN PD11
|
||||
|
||||
#define Z_STEP_PIN PE15
|
||||
#define Z_DIR_PIN PG1
|
||||
#define Z_ENABLE_PIN PD8
|
||||
|
||||
#define E0_STEP_PIN PB1
|
||||
#define E0_DIR_PIN PB2
|
||||
#define E0_ENABLE_PIN PE11
|
||||
|
||||
#define E1_STEP_PIN PC4
|
||||
#define E1_DIR_PIN PC5
|
||||
#define E1_ENABLE_PIN PB0
|
||||
|
||||
#define E2_STEP_PIN PC13
|
||||
#define E2_DIR_PIN PC14
|
||||
#define E2_ENABLE_PIN PC15
|
||||
|
||||
#define Z2_STEP_PIN PC13
|
||||
#define Z2_DIR_PIN PC14
|
||||
#define Z2_ENABLE_PIN PC15
|
||||
|
||||
#define SCK_PIN PA5
|
||||
#define MISO_PIN PA6
|
||||
#define MOSI_PIN PA7
|
||||
|
||||
#define SPI1_SCK_PIN PA5
|
||||
#define SPI1_MISO_PIN PA6
|
||||
#define SPI1_MOSI_PIN PA7
|
||||
|
||||
#define SPI6_SCK_PIN PG13
|
||||
#define SPI6_MISO_PIN PG12
|
||||
#define SPI6_MOSI_PIN PG14
|
||||
|
||||
//
|
||||
// Temperature Sensors
|
||||
//
|
||||
|
||||
#define TEMP_0_PIN PC3 // Analog Input
|
||||
#define TEMP_1_PIN PC2 // Analog Input
|
||||
#define TEMP_2_PIN PC1 // Analog Input
|
||||
#define TEMP_3_PIN PC0 // Analog Input
|
||||
|
||||
#define TEMP_BED_PIN PF10 // Analog Input
|
||||
|
||||
#define TEMP_5_PIN PE12 // Analog Input, Probe temp
|
||||
|
||||
//
|
||||
// Heaters / Fans
|
||||
//
|
||||
#define HEATER_0_PIN PD15
|
||||
#define HEATER_1_PIN PD14
|
||||
#define HEATER_BED_PIN PF6
|
||||
|
||||
#ifndef FAN_PIN
|
||||
#define FAN_PIN PD13
|
||||
#endif
|
||||
#define FAN1_PIN PA0
|
||||
#define FAN2_PIN PA1
|
||||
|
||||
#ifndef E0_AUTO_FAN_PIN
|
||||
#define E0_AUTO_FAN_PIN PA1
|
||||
#endif
|
||||
|
||||
//
|
||||
// Misc. Functions
|
||||
//
|
||||
|
||||
//#define CASE_LIGHT_PIN_CI PF13
|
||||
//#define CASE_LIGHT_PIN_DO PF14
|
||||
//#define NEOPIXEL_PIN PF13
|
||||
|
||||
//
|
||||
// Průša i3 MK2 Multi Material Multiplexer Support
|
||||
//
|
||||
|
||||
#define E_MUX0_PIN PG3
|
||||
#define E_MUX1_PIN PG4
|
||||
|
||||
//
|
||||
// Servos
|
||||
//
|
||||
|
||||
#define SERVO0_PIN PE13
|
||||
#define SERVO1_PIN PE14
|
||||
|
||||
#define SDSS PA8
|
||||
#define SS_PIN PA8
|
||||
#define LED_PIN PA2 // Alive
|
||||
#define PS_ON_PIN PA3
|
||||
#define KILL_PIN -1 //PD5 // EXP2-10
|
||||
#define PWR_LOSS PG5 // Power loss / nAC_FAULT
|
||||
|
||||
//
|
||||
// MAX7219_DEBUG
|
||||
//
|
||||
#define MAX7219_CLK_PIN PG10 // EXP1-1
|
||||
#define MAX7219_DIN_PIN PD7 // EXP1-3
|
||||
#define MAX7219_LOAD_PIN PD1 // EXP1-5
|
||||
|
||||
//
|
||||
// LCD / Controller
|
||||
//
|
||||
//#define SD_DETECT_PIN -1 //PB6) // EXP2-4
|
||||
#define BEEPER_PIN PG10 // EXP1-1
|
||||
#define LCD_PINS_RS PG9 // EXP1-4
|
||||
#define LCD_PINS_ENABLE PD7 // EXP1-3
|
||||
#define LCD_PINS_D4 PD1 // EXP1-5
|
||||
#define LCD_PINS_D5 PF0 // EXP1-6
|
||||
#define LCD_PINS_D6 PD3 // EXP1-7
|
||||
#define LCD_PINS_D7 PD4 // EXP1-8
|
||||
#define BTN_EN1 PD6 // EXP2-5
|
||||
#define BTN_EN2 PD0 // EXP2-3
|
||||
#define BTN_ENC PG11 // EXP1-2
|
||||
Reference in New Issue
Block a user