Allow Z_MIN_PROBE_REPEATABILITY_TEST solo

Marlin/Configuration.h

@@ -504,6 +504,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -620,7 +623,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/Marlin_main.cpp

@@ -4164,19 +4164,7 @@ inline void gcode_M42() {
   } // code_seen('S')
 }
 
-#if ENABLED(AUTO_BED_LEVELING_FEATURE) && ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
+#if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
-
-  /**
-   * This is redundant since the SanityCheck.h already checks for a valid
-   *  Z_MIN_PROBE_PIN, but here for clarity.
-   */
-  #if ENABLED(Z_MIN_PROBE_ENDSTOP)
-    #if !HAS_Z_MIN_PROBE_PIN
-      #error "You must define Z_MIN_PROBE_PIN to enable Z probe repeatability calculation."
-    #endif
-  #elif !HAS_Z_MIN
-    #error "You must define Z_MIN_PIN to enable Z probe repeatability calculation."
-  #endif
 
   /**
    * M48: Z probe repeatability measurement function.
@@ -4439,7 +4427,7 @@ inline void gcode_M42() {
     report_current_position();
   }
 
-#endif // AUTO_BED_LEVELING_FEATURE && Z_MIN_PROBE_REPEATABILITY_TEST
+#endif // Z_MIN_PROBE_REPEATABILITY_TEST
 
 /**
  * M75: Start print timer
@@ -6958,11 +6946,11 @@ void process_next_command() {
         gcode_M42();
         break;
 
-      #if ENABLED(AUTO_BED_LEVELING_FEATURE) && ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
+      #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
         case 48: // M48 Z probe repeatability
           gcode_M48();
           break;
-      #endif // AUTO_BED_LEVELING_FEATURE && Z_MIN_PROBE_REPEATABILITY_TEST
+      #endif // Z_MIN_PROBE_REPEATABILITY_TEST
 
       case 75: // Start print timer
         gcode_M75();

Marlin/SanityCheck.h

@@ -300,10 +300,12 @@
 #else
 
   /**
-   * Require some kind of probe for bed leveling
+   * Require some kind of probe for bed leveling and probe testing
    */
   #if ENABLED(AUTO_BED_LEVELING_FEATURE)
     #error "AUTO_BED_LEVELING_FEATURE requires a probe! Define a Z Servo, MECHANICAL_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
+  #elif ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
+    #error "Z_MIN_PROBE_REPEATABILITY_TEST requires a probe! Define a Z Servo, MECHANICAL_PROBE, Z_PROBE_ALLEN_KEY, Z_PROBE_SLED, or FIX_MOUNTED_PROBE."
   #endif
 
 #endif
@@ -318,11 +320,7 @@
    */
   #if !PIN_EXISTS(Z_MIN)
     #if !PIN_EXISTS(Z_MIN_PROBE) || (DISABLED(Z_MIN_PROBE_ENDSTOP) || ENABLED(DISABLE_Z_MIN_PROBE_ENDSTOP)) // It's possible for someone to set a pin for the Z probe, but not enable it.
-      #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST)
+      #error "AUTO_BED_LEVELING_FEATURE requires a Z_MIN or Z_PROBE endstop. Z_MIN_PIN or Z_MIN_PROBE_PIN must point to a valid hardware pin."
-        #error "You must have a Z_MIN or Z_PROBE endstop to enable Z_MIN_PROBE_REPEATABILITY_TEST."
-      #else
-        #error "AUTO_BED_LEVELING_FEATURE requires a Z_MIN or Z_PROBE endstop. Z_MIN_PIN or Z_MIN_PROBE_PIN must point to a valid hardware pin."
-      #endif
     #endif
   #endif
 

Marlin/example_configurations/Cartesio/Configuration.h

@@ -503,6 +503,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // If you're using the Z MIN endstop connector for your Z probe, this has no effect.
 //#define DISABLE_Z_MIN_PROBE_ENDSTOP
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -619,7 +622,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/Felix/Configuration.h

@@ -486,6 +486,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -602,8 +605,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -484,6 +484,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -600,8 +603,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/Hephestos/Configuration.h

@@ -496,6 +496,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -612,7 +615,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/Hephestos_2/Configuration.h

@@ -498,6 +498,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -614,7 +617,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 #define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/K8200/Configuration.h

@@ -521,6 +521,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -637,7 +640,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -504,6 +504,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -620,7 +623,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/RigidBot/Configuration.h

@@ -498,6 +498,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -614,8 +617,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/SCARA/Configuration.h

@@ -512,6 +512,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -628,8 +631,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/TAZ4/Configuration.h

@@ -525,6 +525,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -641,7 +644,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/WITBOX/Configuration.h

@@ -496,6 +496,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -612,7 +615,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -504,6 +504,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -620,7 +623,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -583,6 +583,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 #endif // Z_PROBE_ALLEN_KEY
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -699,8 +702,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/delta/generic/Configuration.h

@@ -577,6 +577,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 #endif // Z_PROBE_ALLEN_KEY
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -693,8 +696,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -580,6 +580,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 #endif // Z_PROBE_ALLEN_KEY
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -696,8 +699,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -574,6 +574,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 #endif // Z_PROBE_ALLEN_KEY
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -690,8 +693,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 #define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -575,6 +575,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 #endif // Z_PROBE_ALLEN_KEY
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -691,8 +694,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 #define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-//#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
+//
-
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 
   // There are 2 different ways to specify probing locations:

Marlin/example_configurations/makibox/Configuration.h

@@ -507,6 +507,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -623,7 +626,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)
 

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -494,6 +494,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 // Allen Key Probe is defined in the Delta example configurations.
 //
 
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
 //
 // Probe Raise options provide clearance for the probe to deploy and stow.
 //
@@ -610,7 +613,6 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
 
 //#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
 //#define DEBUG_LEVELING_FEATURE
-#define Z_MIN_PROBE_REPEATABILITY_TEST  // If not commented out, Z Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #if ENABLED(AUTO_BED_LEVELING_FEATURE)