Apply overridables to Configuration files
This commit is contained in:
Scott Lahteine
committed by
Richard Wackerbarth
Richard Wackerbarth
parent
819fa7216e
commit
37d1879386
@ -38,7 +38,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
|
||||
// @section info
|
||||
|
||||
#ifdef HAS_AUTOMATIC_VERSIONING
|
||||
#if ENABLED(HAS_AUTOMATIC_VERSIONING)
|
||||
#include "_Version.h"
|
||||
#else
|
||||
#include "Default_Version.h"
|
||||
@ -195,7 +195,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
#define PIDTEMP
|
||||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#ifdef PIDTEMP
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
@ -248,7 +248,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
|
||||
//#define PID_BED_DEBUG // Sends debug data to the serial port.
|
||||
|
||||
#ifdef PIDTEMPBED
|
||||
#if ENABLED(PIDTEMPBED)
|
||||
|
||||
#define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
|
||||
|
||||
@ -316,7 +316,7 @@ Here are some standard links for getting your machine calibrated:
|
||||
// Enable DELTA kinematics and most of the default configuration for Deltas
|
||||
#define DELTA
|
||||
|
||||
#ifdef DELTA
|
||||
#if ENABLED(DELTA)
|
||||
|
||||
// Make delta curves from many straight lines (linear interpolation).
|
||||
// This is a trade-off between visible corners (not enough segments)
|
||||
@ -443,7 +443,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
|
||||
// It is assumed that when logic high = filament available
|
||||
// when logic low = filament ran out
|
||||
#ifdef FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned
|
||||
#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
|
||||
#define FILAMENT_RUNOUT_SCRIPT "M600"
|
||||
@ -456,11 +456,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling
|
||||
// #define MESH_BED_LEVELING // Enable mesh bed leveling
|
||||
|
||||
#ifdef MANUAL_BED_LEVELING
|
||||
#if ENABLED(MANUAL_BED_LEVELING)
|
||||
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis
|
||||
#endif // MANUAL_BED_LEVELING
|
||||
|
||||
#ifdef MESH_BED_LEVELING
|
||||
#if ENABLED(MESH_BED_LEVELING)
|
||||
#define MESH_MIN_X 10
|
||||
#define MESH_MAX_X (X_MAX_POS - MESH_MIN_X)
|
||||
#define MESH_MIN_Y 10
|
||||
@ -479,7 +479,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
|
||||
//#define Z_PROBE_REPEATABILITY_TEST // Z-Probe Repeatability test is not supported in Deltas yet.
|
||||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
#if ENABLED(ENABLE_AUTO_BED_LEVELING)
|
||||
|
||||
// There are 2 different ways to specify probing locations
|
||||
//
|
||||
@ -496,7 +496,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID // Deltas only support grid mode
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
#if ENABLED(AUTO_BED_LEVELING_GRID)
|
||||
|
||||
// set the rectangle in which to probe
|
||||
#define DELTA_PROBABLE_RADIUS (DELTA_PRINTABLE_RADIUS - 10)
|
||||
@ -551,7 +551,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// Deploys by touching z-axis belt. Retracts by pushing the probe down. Uses Z_MIN_PIN.
|
||||
//#define Z_PROBE_ALLEN_KEY
|
||||
|
||||
#ifdef Z_PROBE_ALLEN_KEY
|
||||
#if ENABLED(Z_PROBE_ALLEN_KEY)
|
||||
// 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
|
||||
// if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
|
||||
|
||||
@ -638,7 +638,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
|
||||
// - Block Z homing only when the probe is outside bed area.
|
||||
|
||||
#ifdef Z_SAFE_HOMING
|
||||
#if ENABLED(Z_SAFE_HOMING)
|
||||
|
||||
#define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2) // X point for Z homing when homing all axis (G28)
|
||||
#define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2) // Y point for Z homing when homing all axis (G28)
|
||||
@ -670,7 +670,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
|
||||
// Manual homing switch locations:
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#ifdef MANUAL_HOME_POSITIONS
|
||||
#if ENABLED(MANUAL_HOME_POSITIONS)
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
#define MANUAL_Z_HOME_POS 250 // For delta: Distance between nozzle and print surface after homing.
|
||||
@ -709,8 +709,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
#ifdef CUSTOM_M_CODES
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
#if ENABLED(CUSTOM_M_CODES)
|
||||
#if ENABLED(ENABLE_AUTO_BED_LEVELING)
|
||||
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
|
||||
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||||
@ -727,7 +727,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
//define this to enable EEPROM support
|
||||
//#define EEPROM_SETTINGS
|
||||
|
||||
#ifdef EEPROM_SETTINGS
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
// To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
||||
#define EEPROM_CHITCHAT // Please keep turned on if you can.
|
||||
#endif
|
||||
@ -918,7 +918,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
|
||||
// With this option servos are powered only during movement, then turned off to prevent jitter.
|
||||
//#define DEACTIVATE_SERVOS_AFTER_MOVE
|
||||
|
||||
#ifdef DEACTIVATE_SERVOS_AFTER_MOVE
|
||||
#if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE)
|
||||
// Delay (in microseconds) before turning the servo off. This depends on the servo speed.
|
||||
// 300ms is a good value but you can try less delay.
|
||||
// If the servo can't reach the requested position, increase it.
|
||||
|
||||
Reference in New Issue
Block a user