config updates
This commit is contained in:
Scott Lahteine
@@ -279,9 +279,10 @@
|
||||
*/
|
||||
//#define USE_CONTROLLER_FAN
|
||||
#if ENABLED(USE_CONTROLLER_FAN)
|
||||
//#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
|
||||
#define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
|
||||
#define CONTROLLERFAN_SPEED 255 // 255 == full speed
|
||||
//#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
|
||||
#define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
|
||||
#define CONTROLLERFAN_SPEED 255 // 255 == full speed
|
||||
//#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled
|
||||
#endif
|
||||
|
||||
// When first starting the main fan, run it at full speed for the
|
||||
@@ -657,10 +658,10 @@
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// @section extras
|
||||
// @section motion
|
||||
|
||||
// minimum time in microseconds that a movement needs to take if the buffer is emptied.
|
||||
#define DEFAULT_MINSEGMENTTIME 20000
|
||||
// Minimum time that a segment needs to take if the buffer is emptied
|
||||
#define DEFAULT_MINSEGMENTTIME 20000 // (ms)
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
#define SLOWDOWN
|
||||
@@ -850,11 +851,35 @@
|
||||
#define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
|
||||
#endif
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
#if ENABLED(LCD_INFO_MENU)
|
||||
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
|
||||
#endif
|
||||
#if HAS_LCD_MENU
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
#if ENABLED(LCD_INFO_MENU)
|
||||
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
|
||||
#endif
|
||||
|
||||
// BACK menu items keep the highlight at the top
|
||||
//#define TURBO_BACK_MENU_ITEM
|
||||
|
||||
/**
|
||||
* LED Control Menu
|
||||
* Add LED Control to the LCD menu
|
||||
*/
|
||||
//#define LED_CONTROL_MENU
|
||||
#if ENABLED(LED_CONTROL_MENU)
|
||||
#define LED_COLOR_PRESETS // Enable the Preset Color menu option
|
||||
#if ENABLED(LED_COLOR_PRESETS)
|
||||
#define LED_USER_PRESET_RED 255 // User defined RED value
|
||||
#define LED_USER_PRESET_GREEN 128 // User defined GREEN value
|
||||
#define LED_USER_PRESET_BLUE 0 // User defined BLUE value
|
||||
#define LED_USER_PRESET_WHITE 255 // User defined WHITE value
|
||||
#define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
|
||||
//#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#endif // HAS_LCD_MENU
|
||||
|
||||
// Scroll a longer status message into view
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
@@ -879,23 +904,6 @@
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/**
|
||||
* LED Control Menu
|
||||
* Enable this feature to add LED Control to the LCD menu
|
||||
*/
|
||||
//#define LED_CONTROL_MENU
|
||||
#if ENABLED(LED_CONTROL_MENU)
|
||||
#define LED_COLOR_PRESETS // Enable the Preset Color menu option
|
||||
#if ENABLED(LED_COLOR_PRESETS)
|
||||
#define LED_USER_PRESET_RED 255 // User defined RED value
|
||||
#define LED_USER_PRESET_GREEN 128 // User defined GREEN value
|
||||
#define LED_USER_PRESET_BLUE 0 // User defined BLUE value
|
||||
#define LED_USER_PRESET_WHITE 255 // User defined WHITE value
|
||||
#define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity
|
||||
//#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup
|
||||
#endif
|
||||
#endif // LED_CONTROL_MENU
|
||||
|
||||
#if ENABLED(SDSUPPORT)
|
||||
|
||||
// Some RAMPS and other boards don't detect when an SD card is inserted. You can work
|
||||
@@ -930,6 +938,7 @@
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
//#define POWER_LOSS_PIN 28 // Pin to detect power loss
|
||||
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
|
||||
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate
|
||||
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
|
||||
//#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
|
||||
|
||||
@@ -1134,6 +1143,7 @@
|
||||
//#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
|
||||
//#define STATUS_HEAT_PERCENT // Show heating in a progress bar
|
||||
//#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
|
||||
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of PROGMEM.
|
||||
|
||||
// Frivolous Game Options
|
||||
//#define MARLIN_BRICKOUT
|
||||
@@ -1143,6 +1153,53 @@
|
||||
|
||||
#endif // HAS_GRAPHICAL_LCD
|
||||
|
||||
//
|
||||
// Lulzbot Touch UI
|
||||
//
|
||||
#if ENABLED(LULZBOT_TOUCH_UI)
|
||||
// Display board used
|
||||
//#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240)
|
||||
//#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272)
|
||||
//#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272)
|
||||
//#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480)
|
||||
//#define LCD_ALEPHOBJECTS_CLCD_UI // Aleph Objects Color LCD UI
|
||||
|
||||
// Correct the resolution if not using the stock TFT panel.
|
||||
//#define TOUCH_UI_320x240
|
||||
//#define TOUCH_UI_480x272
|
||||
//#define TOUCH_UI_800x480
|
||||
|
||||
// Mappings for boards with a standard RepRapDiscount Display connector
|
||||
//#define AO_EXP1_PINMAP // AlephObjects CLCD UI EXP1 mapping
|
||||
//#define AO_EXP2_PINMAP // AlephObjects CLCD UI EXP2 mapping
|
||||
//#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping
|
||||
//#define OTHER_PIN_LAYOUT // Define pins manually below
|
||||
#if ENABLED(OTHER_PIN_LAYOUT)
|
||||
// The pins for CS and MOD_RESET (PD) must be chosen.
|
||||
#define CLCD_MOD_RESET 9
|
||||
#define CLCD_SPI_CS 10
|
||||
|
||||
// If using software SPI, specify pins for SCLK, MOSI, MISO
|
||||
//#define CLCD_USE_SOFT_SPI
|
||||
#if ENABLED(CLCD_USE_SOFT_SPI)
|
||||
#define CLCD_SOFT_SPI_MOSI 11
|
||||
#define CLCD_SOFT_SPI_MISO 12
|
||||
#define CLCD_SOFT_SPI_SCLK 13
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// Display Orientation. An inverted (i.e. upside-down) display
|
||||
// is supported on the FT800. The FT810 and beyond also support
|
||||
// portrait and mirrored orientations.
|
||||
//#define TOUCH_UI_INVERTED
|
||||
//#define TOUCH_UI_PORTRAIT
|
||||
//#define TOUCH_UI_MIRRORED
|
||||
|
||||
// Use a numeric passcode for "Screen lock" keypad.
|
||||
// (recommended for smaller displays)
|
||||
//#define TOUCH_UI_PASSCODE
|
||||
#endif
|
||||
|
||||
// @section safety
|
||||
|
||||
/**
|
||||
@@ -2242,6 +2299,13 @@
|
||||
*/
|
||||
#define EXTENDED_CAPABILITIES_REPORT
|
||||
|
||||
/**
|
||||
* Expected Printer Check
|
||||
* Add the M16 G-code to compare a string to the MACHINE_NAME.
|
||||
* M16 with a non-matching string causes the printer to halt.
|
||||
*/
|
||||
//#define EXPECTED_PRINTER_CHECK
|
||||
|
||||
/**
|
||||
* Disable all Volumetric extrusion options
|
||||
*/
|
||||
@@ -2296,6 +2360,13 @@
|
||||
//#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Startup commands
|
||||
*
|
||||
* Execute certain G-code commands immediately after power-on.
|
||||
*/
|
||||
//#define STARTUP_COMMANDS "M17 Z"
|
||||
|
||||
/**
|
||||
* G-code Macros
|
||||
*
|
||||
|
||||
Reference in New Issue
Block a user