bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

Format some pins files

Browse Source
This commit is contained in:
Scott Lahteine
2020-03-21 21:13:19 -05:00
committed by Scott Lahteine
parent 9340a33980
commit 2c325c2a7d
174 changed files with 9635 additions and 9668 deletions
Download Patch File Download Diff File Expand all files Collapse all files

126
Marlin/src/pins/stm32f1/pins_BTT_SKR_E3_DIP.h
View File

@ -42,56 +42,56 @@
//
// Servos
//
#define SERVO0_PIN PA1 // SERVOS
#define SERVO0_PIN PA1 // SERVOS
//
// Limit Switches
//
#define X_STOP_PIN PC1 // X-STOP
#define Y_STOP_PIN PC0 // Y-STOP
#define Z_STOP_PIN PC15 // Z-STOP
#define X_STOP_PIN PC1 // X-STOP
#define Y_STOP_PIN PC0 // Y-STOP
#define Z_STOP_PIN PC15 // Z-STOP
//
// Z Probe must be this pin
//
#define Z_MIN_PROBE_PIN PC14 // PROBE
#define Z_MIN_PROBE_PIN PC14 // PROBE
//
// Filament Runout Sensor
//
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN PC2 // E0-STOP
#define FIL_RUNOUT_PIN PC2 // E0-STOP
#endif
//
// Steppers
//
#define X_ENABLE_PIN PC7
#define X_STEP_PIN PC6
#define X_DIR_PIN PB15
#define X_ENABLE_PIN PC7
#define X_STEP_PIN PC6
#define X_DIR_PIN PB15
#ifndef X_CS_PIN
#define X_CS_PIN PC10
#define X_CS_PIN PC10
#endif
#define Y_ENABLE_PIN PB14
#define Y_STEP_PIN PB13
#define Y_DIR_PIN PB12
#define Y_ENABLE_PIN PB14
#define Y_STEP_PIN PB13
#define Y_DIR_PIN PB12
#ifndef Y_CS_PIN
#define Y_CS_PIN PC11
#define Y_CS_PIN PC11
#endif
#define Z_ENABLE_PIN PB11
#define Z_STEP_PIN PB10
#define Z_DIR_PIN PB2
#define Z_ENABLE_PIN PB11
#define Z_STEP_PIN PB10
#define Z_DIR_PIN PB2
#ifndef Z_CS_PIN
#define Z_CS_PIN PC12
#define Z_CS_PIN PC12
#endif
#define E0_ENABLE_PIN PB1
#define E0_STEP_PIN PB0
#define E0_DIR_PIN PC5
#define E0_ENABLE_PIN PB1
#define E0_STEP_PIN PB0
#define E0_DIR_PIN PC5
#ifndef E0_CS_PIN
#define E0_CS_PIN PD2
#define E0_CS_PIN PD2
#endif
//
@ -99,13 +99,13 @@
//
#if ENABLED(TMC_USE_SW_SPI)
#ifndef TMC_SW_MOSI
#define TMC_SW_MOSI PB5
#define TMC_SW_MOSI PB5
#endif
#ifndef TMC_SW_MISO
#define TMC_SW_MISO PB4
#define TMC_SW_MISO PB4
#endif
#ifndef TMC_SW_SCK
#define TMC_SW_SCK PB3
#define TMC_SW_SCK PB3
#endif
#endif
@ -124,17 +124,17 @@
//
// Software serial
//
#define X_SERIAL_TX_PIN PC10
#define X_SERIAL_RX_PIN PC10
#define X_SERIAL_TX_PIN PC10
#define X_SERIAL_RX_PIN PC10
#define Y_SERIAL_TX_PIN PC11
#define Y_SERIAL_RX_PIN PC11
#define Y_SERIAL_TX_PIN PC11
#define Y_SERIAL_RX_PIN PC11
#define Z_SERIAL_TX_PIN PC12
#define Z_SERIAL_RX_PIN PC12
#define Z_SERIAL_TX_PIN PC12
#define Z_SERIAL_RX_PIN PC12
#define E0_SERIAL_TX_PIN PD2
#define E0_SERIAL_RX_PIN PD2
#define E0_SERIAL_TX_PIN PD2
#define E0_SERIAL_RX_PIN PD2
// Reduce baud rate to improve software serial reliability
#define TMC_BAUD_RATE 19200
@ -143,23 +143,23 @@
//
// Temperature Sensors
//
#define TEMP_0_PIN PA0 // Analog Input "TH0"
#define TEMP_BED_PIN PC3 // Analog Input "TB0"
#define TEMP_0_PIN PA0 // Analog Input "TH0"
#define TEMP_BED_PIN PC3 // Analog Input "TB0"
//
// Heaters / Fans
//
#define HEATER_0_PIN PC8 // HE
#define HEATER_BED_PIN PC9 // HB
#define FAN_PIN PA8 // FAN0
#define HEATER_0_PIN PC8 // HE
#define HEATER_BED_PIN PC9 // HB
#define FAN_PIN PA8 // FAN0
//
// USB connect control
//
#define USB_CONNECT_PIN PC13
#define USB_CONNECT_PIN PC13
#define USB_CONNECT_INVERTING false
#define SD_DETECT_PIN PC4
#define SD_DETECT_PIN PC4
/**
* _____
@ -172,27 +172,27 @@
* EXP1
*/
#define EXPA1_03_PIN PB7
#define EXPA1_04_PIN PB8
#define EXPA1_05_PIN PB9
#define EXPA1_06_PIN PA10
#define EXPA1_07_PIN -1
#define EXPA1_08_PIN PA9
#define EXPA1_09_PIN PB6
#define EXPA1_10_PIN PA15
#define EXPA1_03_PIN PB7
#define EXPA1_04_PIN PB8
#define EXPA1_05_PIN PB9
#define EXPA1_06_PIN PA10
#define EXPA1_07_PIN -1
#define EXPA1_08_PIN PA9
#define EXPA1_09_PIN PB6
#define EXPA1_10_PIN PA15
#if HAS_SPI_LCD
#define BTN_ENC EXPA1_09_PIN
#define BTN_EN1 EXPA1_08_PIN
#define BTN_EN2 EXPA1_06_PIN
#define BTN_ENC EXPA1_09_PIN
#define BTN_EN1 EXPA1_08_PIN
#define BTN_EN2 EXPA1_06_PIN
#if ENABLED(CR10_STOCKDISPLAY)
#define BEEPER_PIN EXPA1_10_PIN
#define BEEPER_PIN EXPA1_10_PIN
#define LCD_PINS_RS EXPA1_04_PIN
#define LCD_PINS_ENABLE EXPA1_03_PIN
#define LCD_PINS_D4 EXPA1_05_PIN
#define LCD_PINS_RS EXPA1_04_PIN
#define LCD_PINS_ENABLE EXPA1_03_PIN
#define LCD_PINS_D4 EXPA1_05_PIN
#elif EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)
@ -207,12 +207,12 @@
* EXP1
*/
#define DOGLCD_CS EXPA1_04_PIN
#define DOGLCD_A0 EXPA1_05_PIN
#define DOGLCD_SCK EXPA1_10_PIN
#define DOGLCD_MOSI EXPA1_03_PIN
#define DOGLCD_CS EXPA1_04_PIN
#define DOGLCD_A0 EXPA1_05_PIN
#define DOGLCD_SCK EXPA1_10_PIN
#define DOGLCD_MOSI EXPA1_03_PIN
#define FORCE_SOFT_SPI
#define LCD_BACKLIGHT_PIN -1
#define LCD_BACKLIGHT_PIN -1
#else
#error "Only CR10_STOCKDISPLAY, ENDER2_STOCKDISPLAY, and MKS_MINI_12864 are currently supported on the BIGTREE_SKR_E3_DIP."
@ -226,8 +226,8 @@
#define HAS_ONBOARD_SD
#ifndef SDCARD_CONNECTION
#define SDCARD_CONNECTION ONBOARD
#define SDCARD_CONNECTION ONBOARD
#endif
#define ON_BOARD_SPI_DEVICE 1 //SPI1
#define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card
#define ON_BOARD_SPI_DEVICE 1 //SPI1
#define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card

118
Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3.h
View File

@ -40,66 +40,66 @@
//
// Servos
//
#define SERVO0_PIN PA1
#define SERVO0_PIN PA1
//
// Limit Switches
//
#define X_STOP_PIN PC0
#define Y_STOP_PIN PC1
#define Z_STOP_PIN PC2
#define X_STOP_PIN PC0
#define Y_STOP_PIN PC1
#define Z_STOP_PIN PC2
//
// Z Probe must be this pins
//
#define Z_MIN_PROBE_PIN PC14
#define Z_MIN_PROBE_PIN PC14
//
// Filament Runout Sensor
//
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN PC15 // "E0-STOP"
#define FIL_RUNOUT_PIN PC15 // "E0-STOP"
#endif
//
// Steppers
//
#define X_ENABLE_PIN PB14
#define X_STEP_PIN PB13
#define X_DIR_PIN PB12
#define X_ENABLE_PIN PB14
#define X_STEP_PIN PB13
#define X_DIR_PIN PB12
#define Y_ENABLE_PIN PB11
#define Y_STEP_PIN PB10
#define Y_DIR_PIN PB2
#define Y_ENABLE_PIN PB11
#define Y_STEP_PIN PB10
#define Y_DIR_PIN PB2
#define Z_ENABLE_PIN PB1
#define Z_STEP_PIN PB0
#define Z_DIR_PIN PC5
#define Z_ENABLE_PIN PB1
#define Z_STEP_PIN PB0
#define Z_DIR_PIN PC5
#define E0_ENABLE_PIN PD2
#define E0_STEP_PIN PB3
#define E0_DIR_PIN PB4
#define E0_ENABLE_PIN PD2
#define E0_STEP_PIN PB3
#define E0_DIR_PIN PB4
//
// Temperature Sensors
//
#define TEMP_0_PIN PA0 // Analog Input
#define TEMP_BED_PIN PC3 // Analog Input
#define TEMP_0_PIN PA0 // Analog Input
#define TEMP_BED_PIN PC3 // Analog Input
//
// Heaters / Fans
//
#define HEATER_0_PIN PC8 // EXTRUDER
#define HEATER_BED_PIN PC9 // BED
#define FAN_PIN PA8
#define HEATER_0_PIN PC8 // EXTRUDER
#define HEATER_BED_PIN PC9 // BED
#define FAN_PIN PA8
//
// USB connect control
//
#define USB_CONNECT_PIN PC13
#define USB_CONNECT_PIN PC13
#define USB_CONNECT_INVERTING false
#define SD_DETECT_PIN PC4
#define SD_DETECT_PIN PC4
/**
* _____
@ -112,40 +112,40 @@
* EXP1
*/
#define EXPA1_03_PIN PB7
#define EXPA1_04_PIN PB8
#define EXPA1_05_PIN PB9
#define EXPA1_06_PIN PA10
#define EXPA1_07_PIN -1
#define EXPA1_08_PIN PA9
#define EXPA1_09_PIN PB6
#define EXPA1_10_PIN PB5
#define EXPA1_03_PIN PB7
#define EXPA1_04_PIN PB8
#define EXPA1_05_PIN PB9
#define EXPA1_06_PIN PA10
#define EXPA1_07_PIN -1
#define EXPA1_08_PIN PA9
#define EXPA1_09_PIN PB6
#define EXPA1_10_PIN PB5
#if HAS_SPI_LCD
#if ENABLED(CR10_STOCKDISPLAY)
#define BEEPER_PIN EXPA1_10_PIN
#define BEEPER_PIN EXPA1_10_PIN
#define BTN_EN1 EXPA1_08_PIN
#define BTN_EN2 EXPA1_06_PIN
#define BTN_ENC EXPA1_09_PIN
#define BTN_EN1 EXPA1_08_PIN
#define BTN_EN2 EXPA1_06_PIN
#define BTN_ENC EXPA1_09_PIN
#define LCD_PINS_RS EXPA1_04_PIN
#define LCD_PINS_ENABLE EXPA1_03_PIN
#define LCD_PINS_D4 EXPA1_05_PIN
#define LCD_PINS_RS EXPA1_04_PIN
#define LCD_PINS_ENABLE EXPA1_03_PIN
#define LCD_PINS_D4 EXPA1_05_PIN
#elif ENABLED(ZONESTAR_LCD) // ANET A8 LCD Controller - Must convert to 3.3V - CONNECTING TO 5V WILL DAMAGE THE BOARD!
#elif ENABLED(ZONESTAR_LCD) // ANET A8 LCD Controller - Must convert to 3.3V - CONNECTING TO 5V WILL DAMAGE THE BOARD!
#error "CAUTION! ZONESTAR_LCD requires wiring modifications. See 'pins_BTT_SKR_MINI_E3.h' for details. Comment out this line to continue."
#define LCD_PINS_RS EXPA1_05_PIN
#define LCD_PINS_ENABLE EXPA1_09_PIN
#define LCD_PINS_D4 EXPA1_04_PIN
#define LCD_PINS_D5 EXPA1_06_PIN
#define LCD_PINS_D6 EXPA1_08_PIN
#define LCD_PINS_D7 EXPA1_10_PIN
#define ADC_KEYPAD_PIN PA1 // Repurpose servo pin for ADC - CONNECTING TO 5V WILL DAMAGE THE BOARD!
#define LCD_PINS_RS EXPA1_05_PIN
#define LCD_PINS_ENABLE EXPA1_09_PIN
#define LCD_PINS_D4 EXPA1_04_PIN
#define LCD_PINS_D5 EXPA1_06_PIN
#define LCD_PINS_D6 EXPA1_08_PIN
#define LCD_PINS_D7 EXPA1_10_PIN
#define ADC_KEYPAD_PIN PA1 // Repurpose servo pin for ADC - CONNECTING TO 5V WILL DAMAGE THE BOARD!
#elif EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)
@ -159,16 +159,16 @@
* -----
* EXP1
*/
#define BTN_EN1 EXPA1_08_PIN
#define BTN_EN2 EXPA1_06_PIN
#define BTN_ENC EXPA1_09_PIN
#define BTN_EN1 EXPA1_08_PIN
#define BTN_EN2 EXPA1_06_PIN
#define BTN_ENC EXPA1_09_PIN
#define DOGLCD_CS EXPA1_04_PIN
#define DOGLCD_A0 EXPA1_05_PIN
#define DOGLCD_SCK EXPA1_10_PIN
#define DOGLCD_MOSI EXPA1_03_PIN
#define DOGLCD_CS EXPA1_04_PIN
#define DOGLCD_A0 EXPA1_05_PIN
#define DOGLCD_SCK EXPA1_10_PIN
#define DOGLCD_MOSI EXPA1_03_PIN
#define FORCE_SOFT_SPI
#define LCD_BACKLIGHT_PIN -1
#define LCD_BACKLIGHT_PIN -1
#else
@ -184,8 +184,8 @@
#define HAS_ONBOARD_SD
#ifndef SDCARD_CONNECTION
#define SDCARD_CONNECTION ONBOARD
#define SDCARD_CONNECTION ONBOARD
#endif
#define ON_BOARD_SPI_DEVICE 1 // SPI1
#define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card
#define ON_BOARD_SPI_DEVICE 1 // SPI1
#define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card

18
Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_V1_2.h
View File

@ -25,7 +25,7 @@
#define BOARD_INFO_NAME "BIGTREE SKR Mini E3 V1.2"
#define NEOPIXEL_PIN PC7 // LED driving pin
#define NEOPIXEL_PIN PC7 // LED driving pin
/**
* TMC2208/TMC2209 stepper drivers
@ -34,17 +34,17 @@
//
// Software serial
//
#define X_SERIAL_TX_PIN PB15
#define X_SERIAL_RX_PIN PB15
#define X_SERIAL_TX_PIN PB15
#define X_SERIAL_RX_PIN PB15
#define Y_SERIAL_TX_PIN PC6
#define Y_SERIAL_RX_PIN PC6
#define Y_SERIAL_TX_PIN PC6
#define Y_SERIAL_RX_PIN PC6
#define Z_SERIAL_TX_PIN PC10
#define Z_SERIAL_RX_PIN PC10
#define Z_SERIAL_TX_PIN PC10
#define Z_SERIAL_RX_PIN PC10
#define E0_SERIAL_TX_PIN PC11
#define E0_SERIAL_RX_PIN PC11
#define E0_SERIAL_TX_PIN PC11
#define E0_SERIAL_RX_PIN PC11
// Reduce baud rate to improve software serial reliability
#define TMC_BAUD_RATE 19200

130
Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_V1_1.h
View File

@ -41,57 +41,57 @@
//
// Limit Switches
//
#define X_MIN_PIN PC2
#define X_MAX_PIN PA2
#define Y_MIN_PIN PC1
#define Y_MAX_PIN PA1
#define Z_MIN_PIN PC0
#define Z_MAX_PIN PC3
#define X_MIN_PIN PC2
#define X_MAX_PIN PA2
#define Y_MIN_PIN PC1
#define Y_MAX_PIN PA1
#define Z_MIN_PIN PC0
#define Z_MAX_PIN PC3
//
// Steppers
//
#define X_STEP_PIN PC6
#define X_DIR_PIN PC7
#define X_ENABLE_PIN PB15
#define X_STEP_PIN PC6
#define X_DIR_PIN PC7
#define X_ENABLE_PIN PB15
#define Y_STEP_PIN PB13
#define Y_DIR_PIN PB14
#define Y_ENABLE_PIN PB12
#define Y_STEP_PIN PB13
#define Y_DIR_PIN PB14
#define Y_ENABLE_PIN PB12
#define Z_STEP_PIN PB10
#define Z_DIR_PIN PB11
#define Z_ENABLE_PIN PB2
#define Z_STEP_PIN PB10
#define Z_DIR_PIN PB11
#define Z_ENABLE_PIN PB2
#define E0_STEP_PIN PC5
#define E0_DIR_PIN PB0
#define E0_ENABLE_PIN PC4
#define E0_STEP_PIN PC5
#define E0_DIR_PIN PB0
#define E0_ENABLE_PIN PC4
#if ENABLED(TMC_USE_SW_SPI)
#ifndef TMC_SW_SCK
#define TMC_SW_SCK PB3
#define TMC_SW_SCK PB3
#endif
#ifndef TMC_SW_MISO
#define TMC_SW_MISO PB4
#define TMC_SW_MISO PB4
#endif
#ifndef TMC_SW_MOSI
#define TMC_SW_MOSI PB5
#define TMC_SW_MOSI PB5
#endif
#endif
//
// Heaters / Fans
//
#define HEATER_0_PIN PA8
#define FAN_PIN PC8
#define HEATER_BED_PIN PC9
#define HEATER_0_PIN PA8
#define FAN_PIN PC8
#define HEATER_BED_PIN PC9
//
// Temperature Sensors
//
#define TEMP_BED_PIN PB1 // Analog Input
#define TEMP_0_PIN PA0 // Analog Input
#define TEMP_BED_PIN PB1 // Analog Input
#define TEMP_0_PIN PA0 // Analog Input
//
// LCD Pins
@ -109,41 +109,41 @@
*/
#if HAS_SPI_LCD
#define BEEPER_PIN PC10
#define BTN_ENC PC11
#define BEEPER_PIN PC10
#define BTN_ENC PC11
#if ENABLED(CR10_STOCKDISPLAY)
#define LCD_PINS_RS PC15
#define LCD_PINS_RS PC15
#define BTN_EN1 PB6
#define BTN_EN2 PC13
#define BTN_EN1 PB6
#define BTN_EN2 PC13
#define LCD_PINS_ENABLE PC14
#define LCD_PINS_D4 PB7
#define LCD_PINS_ENABLE PC14
#define LCD_PINS_D4 PB7
#else
#define LCD_PINS_RS PC12
#define LCD_PINS_RS PC12
#define BTN_EN1 PD2
#define BTN_EN2 PB8
#define BTN_EN1 PD2
#define BTN_EN2 PB8
#define LCD_PINS_ENABLE PB6
#define LCD_PINS_ENABLE PB6
#if ENABLED(FYSETC_MINI_12864)
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN PC13
#define DOGLCD_A0 PC12
#define DOGLCD_CS PB6
#define DOGLCD_SCK PB3
#define DOGLCD_MOSI PB5
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN PC13
#define DOGLCD_A0 PC12
#define DOGLCD_CS PB6
#define DOGLCD_SCK PB3
#define DOGLCD_MOSI PB5
#define FORCE_SOFT_SPI // SPI MODE3
#define FORCE_SOFT_SPI // SPI MODE3
#define LED_PIN PB7 // red pwm
//#define LED_PIN PC15 // green
//#define LED_PIN PC14 // blue
#define LED_PIN PB7 // red pwm
//#define LED_PIN PC15 // green
//#define LED_PIN PC14 // blue
//#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
// #ifndef RGB_LED_R_PIN
@ -159,13 +159,13 @@
// #define NEOPIXEL_PIN PB7
//#endif
#else // !FYSETC_MINI_12864
#else // !FYSETC_MINI_12864
#define LCD_PINS_D4 PC13
#define LCD_PINS_D4 PC13
#if ENABLED(ULTIPANEL)
#define LCD_PINS_D5 PB7
#define LCD_PINS_D6 PC15
#define LCD_PINS_D7 PC14
#define LCD_PINS_D5 PB7
#define LCD_PINS_D6 PC15
#define LCD_PINS_D7 PC14
#endif
#endif // !FYSETC_MINI_12864
@ -182,26 +182,26 @@
// set SDCARD_CONNECTION form 'ONBOARD' to 'LCD' and use an external SD (connected to LCD)
#define HAS_ONBOARD_SD
#ifndef SDCARD_CONNECTION
#define SDCARD_CONNECTION ONBOARD
#define SDCARD_CONNECTION ONBOARD
#endif
#if SD_CONNECTION_IS(LCD)
#define ENABLE_SPI3
#define SD_DETECT_PIN PB9
#define SCK_PIN PB3
#define MISO_PIN PB4
#define MOSI_PIN PB5
#define SS_PIN PA15
#define SD_DETECT_PIN PB9
#define SCK_PIN PB3
#define MISO_PIN PB4
#define MOSI_PIN PB5
#define SS_PIN PA15
#elif SD_CONNECTION_IS(ONBOARD)
#define ENABLE_SPI1
#define SD_DETECT_PIN PA3
#define SCK_PIN PA5
#define MISO_PIN PA6
#define MOSI_PIN PA7
#define SS_PIN PA4
#define SD_DETECT_PIN PA3
#define SCK_PIN PA5
#define MISO_PIN PA6
#define MOSI_PIN PA7
#define SS_PIN PA4
#endif
#define ON_BOARD_SPI_DEVICE 1 //SPI1
#define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card
#define ON_BOARD_SPI_DEVICE 1 //SPI1
#define ONBOARD_SD_CS_PIN PA4 // Chip select for "System" SD card
#if HAS_GRAPHICAL_LCD
#define BOARD_ST7920_DELAY_1 DELAY_NS(125)

270
Marlin/src/pins/stm32f1/pins_CHITU3D.h
View File

@ -41,69 +41,67 @@
//
// Steppers
//
#define X_STEP_PIN PE5
#define X_DIR_PIN PE6
#define X_ENABLE_PIN PC13
#define X_MIN_PIN PG10
#define X_MAX_PIN -1
#define X_STEP_PIN PE5
#define X_DIR_PIN PE6
#define X_ENABLE_PIN PC13
#define X_MIN_PIN PG10
#define X_MAX_PIN -1
#define Y_STEP_PIN PE2
#define Y_DIR_PIN PE3
#define Y_ENABLE_PIN PE4
#define Y_MIN_PIN PA12
#define Y_STEP_PIN PE2
#define Y_DIR_PIN PE3
#define Y_ENABLE_PIN PE4
#define Y_MIN_PIN PA12
#define Y_MAX_PIN
#define Z_STEP_PIN PB9
#define Z_DIR_PIN PE0
#define Z_ENABLE_PIN PE1
#define Z_MIN_PIN PA14
#define Z_MAX_PIN -1
#define Z_STEP_PIN PB9
#define Z_DIR_PIN PE0
#define Z_ENABLE_PIN PE1
#define Z_MIN_PIN PA14
#define Z_MAX_PIN -1
#define Y2_STEP_PIN -1
#define Y2_DIR_PIN -1
#define Y2_ENABLE_PIN -1
#define Y2_STEP_PIN -1
#define Y2_DIR_PIN -1
#define Y2_ENABLE_PIN -1
#define Z2_STEP_PIN -1
#define Z2_DIR_PIN -1
#define Z2_ENABLE_PIN -1
#define Z2_STEP_PIN -1
#define Z2_DIR_PIN -1
#define Z2_ENABLE_PIN -1
#define E0_STEP_PIN PB4
#define E0_DIR_PIN PB5
#define E0_ENABLE_PIN PB8
#define E0_STEP_PIN PB4
#define E0_DIR_PIN PB5
#define E0_ENABLE_PIN PB8
#define E1_STEP_PIN -1
#define E1_DIR_PIN -1
#define E1_ENABLE_PIN -1
#define E1_STEP_PIN -1
#define E1_DIR_PIN -1
#define E1_ENABLE_PIN -1
#define E2_STEP_PIN -1
#define E2_DIR_PIN -1
#define E2_ENABLE_PIN -1
#define E2_STEP_PIN -1
#define E2_DIR_PIN -1
#define E2_ENABLE_PIN -1
//
// Misc. Functions
//
#define SDSS -1
#define LED_PIN -1
#define CASE_LIGHT_PIN PA8 // 8
#define SDSS -1
#define LED_PIN -1
#define CASE_LIGHT_PIN PA8 // 8
#define PS_ON_PIN -1
#define KILL_PIN PD6 // LED strip 24v
#define PS_ON_PIN -1
#define KILL_PIN PD6 // LED strip 24v
//
// Heaters / Fans
//
#define HEATER_0_PIN PD12 // HOT-END
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define HEATER_0_PIN PD12 // HOT-END
#define HEATER_1_PIN -1
#define HEATER_2_PIN -1
#define HEATER_BED_PIN PG11 // HOT-BED
#define HEATER_BED2_PIN -1 // BED2
#define HEATER_BED3_PIN -1 // BED3
#define HEATER_BED_PIN PG11 // HOT-BED
#define HEATER_BED2_PIN -1 // BED2
#define HEATER_BED3_PIN -1 // BED3
#ifndef FAN_PIN
#define FAN_PIN PG14 // MAIN BOARD FAN
#define FAN_PIN PG14 // MAIN BOARD FAN
#endif
#define FAN_SOFT_PWM
@ -111,10 +109,10 @@
//
// Temperature Sensors
//
#define TEMP_BED_PIN PA0 // Analog Input
#define TEMP_0_PIN PA1 // Analog Input
#define TEMP_1_PIN -1 // Analog Input
#define TEMP_2_PIN -1 // Analog Input
#define TEMP_BED_PIN PA0 // Analog Input
#define TEMP_0_PIN PA1 // Analog Input
#define TEMP_1_PIN -1 // Analog Input
#define TEMP_2_PIN -1 // Analog Input
//
// LCD Pins
@ -122,31 +120,31 @@
#if HAS_SPI_LCD
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define LCD_PINS_RS PD1 // 49 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PD3 // 51 // SID (MOSI)
#define LCD_PINS_D4 PD4 // 52 // SCK (CLK) clock
#define LCD_PINS_RS PD1 // 49 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PD3 // 51 // SID (MOSI)
#define LCD_PINS_D4 PD4 // 52 // SCK (CLK) clock
#elif BOTH(NEWPANEL, PANEL_ONE)
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#else
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#if DISABLED(NEWPANEL)
#define BEEPER_PIN PC1 // 33
#define BEEPER_PIN PC1 // 33
// Buttons attached to a shift register
// Not wired yet
//#define SHIFT_CLK PC6 // 38
//#define SHIFT_LD PC10 // 42
//#define SHIFT_OUT PC8 // 40
//#define SHIFT_EN PA1 // 17
//#define SHIFT_CLK PC6 // 38
//#define SHIFT_LD PC10 // 42
//#define SHIFT_OUT PC8 // 40
//#define SHIFT_EN PA1 // 17
#endif
#endif
@ -154,127 +152,127 @@
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
#define BEEPER_PIN PC5
#define BEEPER_PIN PC5
#define BTN_EN1 PB15 // 31
#define BTN_EN2 PC1 // 33
#define BTN_ENC PC3 // 35
#define BTN_EN1 PB15 // 31
#define BTN_EN2 PC1 // 33
#define BTN_ENC PC3 // 35
#define SD_DETECT_PIN PD1 // 49
#define KILL_PIN PC9 // 41
#define SD_DETECT_PIN PD1 // 49
#define KILL_PIN PC9 // 41
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
#define LCD_BACKLIGHT_PIN PC7 // 39
#define LCD_BACKLIGHT_PIN PC7 // 39
#endif
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define BTN_EN1 PE0 // 64
#define BTN_EN2 PD11 // 59
#define BTN_ENC PD15 // 63
#define SD_DETECT_PIN PC10 // 42
#define BTN_EN1 PE0 // 64
#define BTN_EN2 PD11 // 59
#define BTN_ENC PD15 // 63
#define SD_DETECT_PIN PC10 // 42
#elif ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 PC15 // 47
#define BTN_EN2 PC11 // 43
#define BTN_ENC PC0 // 32
#define LCD_SDSS PD5 // 53
#define SD_DETECT_PIN -1
#define KILL_PIN PC9 // 41
#define BTN_EN1 PC15 // 47
#define BTN_EN2 PC11 // 43
#define BTN_ENC PC0 // 32
#define LCD_SDSS PD5 // 53
#define SD_DETECT_PIN -1
#define KILL_PIN PC9 // 41
#elif ENABLED(LCD_I2C_VIKI)
#define BTN_EN1 PB6 // 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 PA7 // 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_EN1 PB6 // 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 PA7 // 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_ENC -1
#define LCD_SDSS PD5 // 53
#define SD_DETECT_PIN PD1 // 49
#define BTN_ENC -1
#define LCD_SDSS PD5 // 53
#define SD_DETECT_PIN PD1 // 49
#elif ANY(VIKI2, miniVIKI)
#define BEEPER_PIN PC1 // 33
#define BEEPER_PIN PC1 // 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 PC12 // 44
#define DOGLCD_CS PC13 // 45
#define DOGLCD_A0 PC12 // 44
#define DOGLCD_CS PC13 // 45
#define LCD_SCREEN_ROT_180
#define BTN_EN1 PB6 // 22
#define BTN_EN2 PA7 // 7
#define BTN_ENC PC7 // 39
#define BTN_EN1 PB6 // 22
#define BTN_EN2 PA7 // 7
#define BTN_ENC PC7 // 39
#define SDSS PD5 // 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define SDSS PD5 // 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define KILL_PIN PB15 // 31
#define KILL_PIN PB15 // 31
#define STAT_LED_RED_PIN PC0 // 32
#define STAT_LED_BLUE_PIN PC3 // 35
#define STAT_LED_RED_PIN PC0 // 32
#define STAT_LED_BLUE_PIN PC3 // 35
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define BTN_EN1 PC3 // 35
#define BTN_EN2 PC5 // 37
#define BTN_ENC PB15 // 31
#define SD_DETECT_PIN PD1 // 49
#define LCD_SDSS PD5 // 53
#define KILL_PIN PC9 // 41
#define BEEPER_PIN PB7 // 23
#define DOGLCD_CS PB13 // 29
#define DOGLCD_A0 PB11 // 27
#define LCD_BACKLIGHT_PIN PC1 // 33
#define BTN_EN1 PC3 // 35
#define BTN_EN2 PC5 // 37
#define BTN_ENC PB15 // 31
#define SD_DETECT_PIN PD1 // 49
#define LCD_SDSS PD5 // 53
#define KILL_PIN PC9 // 41
#define BEEPER_PIN PB7 // 23
#define DOGLCD_CS PB13 // 29
#define DOGLCD_A0 PB11 // 27
#define LCD_BACKLIGHT_PIN PC1 // 33
#elif ENABLED(MINIPANEL)
#define BEEPER_PIN PC10 // 42
#define BEEPER_PIN PC10 // 42
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 PC12 // 44
#define DOGLCD_CS PE2 // 66
#define LCD_BACKLIGHT_PIN PE1 // 65 // backlight LED on A11/D65
#define SDSS PD5 // 53
#define DOGLCD_A0 PC12 // 44
#define DOGLCD_CS PE2 // 66
#define LCD_BACKLIGHT_PIN PE1 // 65 // backlight LED on A11/D65
#define SDSS PD5 // 53
#define KILL_PIN PE0 // 64
#define KILL_PIN PE0 // 64
// GLCD features
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
// The encoder and click button
#define BTN_EN1 PC8 // 40
#define BTN_EN2 PD15 // 63
#define BTN_ENC PD11 // 59
#define BTN_EN1 PC8 // 40
#define BTN_EN2 PD15 // 63
#define BTN_ENC PD11 // 59
// not connected to a pin
#define SD_DETECT_PIN PD1 // 49
#define SD_DETECT_PIN PD1 // 49
#else
// Beeper on AUX-4
#define BEEPER_PIN PC1 // 33
#define BEEPER_PIN PC1 // 33
// Buttons directly attached to AUX-2
#if ENABLED(REPRAPWORLD_KEYPAD)
#define BTN_EN1 PE0 // 64
#define BTN_EN2 PD11 // 59
#define BTN_ENC PD15 // 63
#define SHIFT_OUT PC8 // 40
#define SHIFT_CLK PC12 // 44
#define SHIFT_LD PC10 // 42
#define BTN_EN1 PE0 // 64
#define BTN_EN2 PD11 // 59
#define BTN_ENC PD15 // 63
#define SHIFT_OUT PC8 // 40
#define SHIFT_CLK PC12 // 44
#define SHIFT_LD PC10 // 42
#elif ENABLED(PANEL_ONE)
#define BTN_EN1 PD11 // 59 // AUX2 PIN 3
#define BTN_EN2 PD15 // 63 // AUX2 PIN 4
#define BTN_ENC PD1 // 49 // AUX3 PIN 7
#define BTN_EN1 PD11 // 59 // AUX2 PIN 3
#define BTN_EN2 PD15 // 63 // AUX2 PIN 4
#define BTN_ENC PD1 // 49 // AUX3 PIN 7
#else
#define BTN_EN1 PC5 // 37
#define BTN_EN2 PC3 // 35
#define BTN_ENC PB15 // 31
#define BTN_EN1 PC5 // 37
#define BTN_EN2 PC3 // 35
#define BTN_ENC PB15 // 31
#endif
#if ENABLED(G3D_PANEL)
#define SD_DETECT_PIN PD1 // 49
#define KILL_PIN PC9 // 41
#define SD_DETECT_PIN PD1 // 49
#define KILL_PIN PC9 // 41
#else
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
#endif
#endif

92
Marlin/src/pins/stm32f1/pins_FYSETC_AIO_II.h
View File

@ -46,55 +46,55 @@
//
// Limit Switches
//
#define X_STOP_PIN PA1
#define Y_STOP_PIN PA0
#define Z_STOP_PIN PB14
#define X_STOP_PIN PA1
#define Y_STOP_PIN PA0
#define Z_STOP_PIN PB14
//
// Filament runout
//
#ifdef pins_v2_20190128
#define FIL_RUNOUT_PIN PB15
#define FIL_RUNOUT_PIN PB15
#else
#define FIL_RUNOUT_PIN PB5
#define FIL_RUNOUT_PIN PB5
#endif
//
// Steppers
//
#define X_STEP_PIN PB8
#define X_DIR_PIN PB9
#define X_ENABLE_PIN PA8
#define X_STEP_PIN PB8
#define X_DIR_PIN PB9
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PB2
#define Y_STEP_PIN PB2
#ifdef pins_v2_20190128
#define Y_DIR_PIN PB3
#define Y_DIR_PIN PB3
#else
#define Y_DIR_PIN PB0
#define Y_DIR_PIN PB0
#endif
#define Y_ENABLE_PIN PB1
#define Y_ENABLE_PIN PB1
#define Z_STEP_PIN PC0
#define Z_DIR_PIN PC1
#define Z_ENABLE_PIN PC2
#define Z_STEP_PIN PC0
#define Z_DIR_PIN PC1
#define Z_ENABLE_PIN PC2
#define E0_STEP_PIN PC15
#define E0_DIR_PIN PC14
#define E0_ENABLE_PIN PC13
#define E0_STEP_PIN PC15
#define E0_DIR_PIN PC14
#define E0_ENABLE_PIN PC13
//
// Stepper current PWM
//
// X:PA2 Y:PA3 Z:PB12 E:PB13 // changed for test
//#define MOTOR_CURRENT_PWM_XY_PIN PA3
//#define MOTOR_CURRENT_PWM_Z_PIN PA2 // PB12
//#define MOTOR_CURRENT_PWM_XY_PIN PB6
//#define MOTOR_CURRENT_PWM_Z_PIN PB7 // PB12
//#define MOTOR_CURRENT_PWM_E_PIN -1 // PB13
//#define MOTOR_CURRENT_PWM_XY_PIN PA3
//#define MOTOR_CURRENT_PWM_Z_PIN PA2 // PB12
//#define MOTOR_CURRENT_PWM_XY_PIN PB6
//#define MOTOR_CURRENT_PWM_Z_PIN PB7 // PB12
//#define MOTOR_CURRENT_PWM_E_PIN -1 // PB13
// Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range
#ifndef MOTOR_CURRENT_PWM_RANGE
#define MOTOR_CURRENT_PWM_RANGE 1500 // geo-f:old 2000
#define MOTOR_CURRENT_PWM_RANGE 1500 // geo-f:old 2000
#endif
#define DEFAULT_PWM_MOTOR_CURRENT {500, 500, 400} // geo-f:old 1300 1300 1250
@ -112,37 +112,37 @@
//
// Heaters / Fans
//
#define HEATER_0_PIN PC7
#define HEATER_BED_PIN PC6
#define HEATER_0_PIN PC7
#define HEATER_BED_PIN PC6
#ifndef FAN_PIN
#define FAN_PIN PC8
#define FAN_PIN PC8
#endif
//
// Temperature Sensors
//
#define TEMP_BED_PIN PC5 // Analog Input
#define TEMP_0_PIN PC4 // Analog Input
#define TEMP_BED_PIN PC5 // Analog Input
#define TEMP_0_PIN PC4 // Analog Input
//
// Misc. Functions
//
#define SDSS PA4
#define SDSS PA4
//
// LCD Pins
//
#if HAS_SPI_LCD
#define BEEPER_PIN PC9
#define BEEPER_PIN PC9
#if HAS_GRAPHICAL_LCD
#define DOGLCD_A0 PA15
#define DOGLCD_A0 PA15
#ifdef pins_v2_20190128
#define DOGLCD_CS PB5
#define DOGLCD_CS PB5
#else
#define DOGLCD_CS PB7
#define DOGLCD_CS PB7
#endif
//#define LCD_CONTRAST_INIT 190
@ -153,36 +153,36 @@
#endif
// not connected to a pin
#define SD_DETECT_PIN PC3
#define SD_DETECT_PIN PC3
#if ENABLED(NEWPANEL)
// The encoder and click button
#define BTN_EN1 PC10
#define BTN_EN2 PC11
#define BTN_ENC PC12
#define BTN_EN1 PC10
#define BTN_EN2 PC11
#define BTN_ENC PC12
#endif
#ifdef pins_v2_20190128
#define LCD_RESET_PIN PB4
#define LCD_RESET_PIN PB4
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN PB0
#define RGB_LED_R_PIN PB0
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN PB6
#define RGB_LED_G_PIN PB6
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN PB7
#define RGB_LED_B_PIN PB7
#endif
#else
#define LCD_RESET_PIN PB6
#define LCD_RESET_PIN PB6
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN PB3
#define RGB_LED_R_PIN PB3
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN PB4
#define RGB_LED_G_PIN PB4
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN PB5
#define RGB_LED_B_PIN PB5
#endif
#endif

76
Marlin/src/pins/stm32f1/pins_FYSETC_CHEETAH.h
View File

@ -44,38 +44,38 @@
//
// Servos
//
#define SERVO0_PIN PA0
#define SERVO0_PIN PA0
//
// Limit Switches
//
#define X_STOP_PIN PA1
#define Y_STOP_PIN PB4
#define Z_STOP_PIN PA15
#define X_STOP_PIN PA1
#define Y_STOP_PIN PB4
#define Z_STOP_PIN PA15
//
// Filament runout
//
#define FIL_RUNOUT_PIN PB5
#define FIL_RUNOUT_PIN PB5
//
// Steppers
//
#define X_STEP_PIN PB8
#define X_DIR_PIN PB9
#define X_ENABLE_PIN PA8
#define X_STEP_PIN PB8
#define X_DIR_PIN PB9
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PB2
#define Y_DIR_PIN PB3
#define Y_ENABLE_PIN PB1
#define Y_STEP_PIN PB2
#define Y_DIR_PIN PB3
#define Y_ENABLE_PIN PB1
#define Z_STEP_PIN PC0
#define Z_DIR_PIN PC1
#define Z_ENABLE_PIN PC2
#define Z_STEP_PIN PC0
#define Z_DIR_PIN PC1
#define Z_ENABLE_PIN PC2
#define E0_STEP_PIN PC15
#define E0_DIR_PIN PC14
#define E0_ENABLE_PIN PC13
#define E0_STEP_PIN PC15
#define E0_DIR_PIN PC14
#define E0_ENABLE_PIN PC13
#define X_HARDWARE_SERIAL MSerial2
#define Y_HARDWARE_SERIAL MSerial2
@ -85,35 +85,35 @@
//
// Heaters / Fans
//
#define HEATER_0_PIN PC6
#define HEATER_BED_PIN PC7
#define HEATER_0_PIN PC6
#define HEATER_BED_PIN PC7
#ifndef FAN_PIN
#define FAN_PIN PC8
#define FAN_PIN PC8
#endif
//
// Temperature Sensors
//
#define TEMP_BED_PIN PC5 // Analog Input
#define TEMP_0_PIN PC4 // Analog Input
#define TEMP_BED_PIN PC5 // Analog Input
#define TEMP_0_PIN PC4 // Analog Input
//
// Misc. Functions
//
#define SDSS PA4
#define SDSS PA4
//
// LCD Pins
//
#if HAS_SPI_LCD
#define BEEPER_PIN PC9
#define BEEPER_PIN PC9
#if HAS_GRAPHICAL_LCD
#define DOGLCD_A0 PB14
#define DOGLCD_CS PB12
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
#define DOGLCD_A0 PB14
#define DOGLCD_CS PB12
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
@ -123,29 +123,29 @@
#endif
#endif
#define LCD_PINS_RS PB12 // CS -- SOFT SPI for ENDER3 LCD
#define LCD_PINS_D4 PB13 // SCLK
#define LCD_PINS_ENABLE PB15 // DATA MOSI
#define LCD_PINS_RS PB12 // CS -- SOFT SPI for ENDER3 LCD
#define LCD_PINS_D4 PB13 // SCLK
#define LCD_PINS_ENABLE PB15 // DATA MOSI
// not connected to a pin
#define SD_DETECT_PIN PC3
#define SD_DETECT_PIN PC3
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN PB0
#define RGB_LED_R_PIN PB0
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN PB7
#define RGB_LED_G_PIN PB7
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN PB6
#define RGB_LED_B_PIN PB6
#endif
//#define LCD_CONTRAST_INIT 190
#if ENABLED(NEWPANEL)
#define BTN_EN1 PC11
#define BTN_EN2 PC10
#define BTN_ENC PC12
#define BTN_EN1 PC11
#define BTN_EN2 PC10
#define BTN_ENC PC12
#endif
#endif

18
Marlin/src/pins/stm32f1/pins_FYSETC_CHEETAH_V12.h
View File

@ -36,7 +36,7 @@
#undef RGB_LED_G_PIN
#undef RGB_LED_B_PIN
#define FAN1_PIN PB0 // Fan1
#define FAN1_PIN PB0 // Fan1
#if HAS_TMC_UART
@ -47,17 +47,17 @@
//
// Software serial
//
#define X_SERIAL_TX_PIN PA11
#define X_SERIAL_RX_PIN PA12
#define X_SERIAL_TX_PIN PA11
#define X_SERIAL_RX_PIN PA12
#define Y_SERIAL_TX_PIN PB6
#define Y_SERIAL_RX_PIN PB7
#define Y_SERIAL_TX_PIN PB6
#define Y_SERIAL_RX_PIN PB7
#define Z_SERIAL_TX_PIN PB10
#define Z_SERIAL_RX_PIN PB11
#define Z_SERIAL_TX_PIN PB10
#define Z_SERIAL_RX_PIN PB11
#define E0_SERIAL_TX_PIN PA2
#define E0_SERIAL_RX_PIN PA3
#define E0_SERIAL_TX_PIN PA2
#define E0_SERIAL_RX_PIN PA3
// Reduce baud rate to improve software serial reliability
#define TMC_BAUD_RATE 19200

130
Marlin/src/pins/stm32f1/pins_GTM32_MINI.h
View File

@ -53,32 +53,32 @@
// Enable EEPROM Emulation for this board as it doesn't have EEPROM
#define FLASH_EEPROM_EMULATION
#define E2END 0xFFF // 4KB
#define E2END 0xFFF // 4KB
//
// Limit Switches
//
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE1 // ENDSTOPS 3,5
#define Z_MAX_PIN PE0 // ENDSTOPS 4,6
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE1 // ENDSTOPS 3,5
#define Z_MAX_PIN PE0 // ENDSTOPS 4,6
//
// Steppers
//
#define X_STEP_PIN PC6
#define X_DIR_PIN PD13
#define X_ENABLE_PIN PA8
#define X_STEP_PIN PC6
#define X_DIR_PIN PD13
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PA12
#define Y_DIR_PIN PA11
#define Y_ENABLE_PIN PA15
#define Y_STEP_PIN PA12
#define Y_DIR_PIN PA11
#define Y_ENABLE_PIN PA15
#define Z_STEP_PIN PD6
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
#define Z_STEP_PIN PD6
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
// Extruder stepper pins
// NOTE: Numbering here is made according to EXT connector numbers,
@ -86,46 +86,46 @@
// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step
// stick that drives the EXT0 output on the board.
//
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
//
// Heaters / Fans
//
#define HEATER_0_PIN PB0 // EXT0 port
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
#define HEATER_0_PIN PB0 // EXT0 port
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
//
// These are FAN PWM pins on EXT0..EXT2 connectors.
//
//#define FAN_PIN PB9 // EXT0 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
//#define FAN_PIN PB9 // EXT0 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
//
// Temperature Sensors
//
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
//
// Misc. Functions
//
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
//
// LCD / Controller
@ -138,19 +138,19 @@
// Geeetech's LCD2004A Control Panel is very much like
// RepRapDiscount Smart Controller, but adds an FFC40 connector
//
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
#define LCD_PINS_D5 PD9
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
#define LCD_PINS_D5 PD9
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#else
//
// Serial LCDs can be implemented in ExtUI
//
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
#endif
#if HAS_GRAPHICAL_LCD
@ -167,9 +167,9 @@
// RepRapDiscount Smart Controller, but adds an FFC40 connector
// connected with a flat wire to J2 connector on the board.
//
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
#define GTM32_PRO_VB_USE_LCD_BEEPER
#define GTM32_PRO_VB_USE_EXT_SDCARD
@ -182,10 +182,10 @@
// This is pin 32 on J2 FFC40 and pin, goes to the beeper
// on Geeetech's version of RepRapDiscount Smart Controller
// (e.g. on Rostock 301)
#define BEEPER_PIN PE12
#define BEEPER_PIN PE12
#else
// This is the beeper on the board itself
#define BEEPER_PIN PB10
#define BEEPER_PIN PB10
#endif
/**
@ -203,28 +203,28 @@
//
// SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector
//
#define SS_PIN PC11
#define SCK_PIN PC12
#define MOSI_PIN PD2
#define MISO_PIN PC8
#define SD_DETECT_PIN PC7
#define SS_PIN PC11
#define SCK_PIN PC12
#define MOSI_PIN PD2
#define MISO_PIN PC8
#define SD_DETECT_PIN PC7
#else
//
// Use the on-board card socket labeled TF_CARD_SOCKET
//
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#endif
#define SDSS SS_PIN
#define SDSS SS_PIN
//
// ESP WiFi can be soldered to J9 connector which is wired to USART2.
// Must define WIFISUPPORT in Configuration.h for the printer.
//
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1

130
Marlin/src/pins/stm32f1/pins_GTM32_MINI_A30.h
View File

@ -53,32 +53,32 @@
// Enable EEPROM Emulation for this board as it doesn't have EEPROM
#define FLASH_EEPROM_EMULATION
#define E2END 0xFFF // 4KB
#define E2END 0xFFF // 4KB
//
// Limit Switches
//
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE0 // ENDSTOPS 3,5
#define Z_MAX_PIN PE1 // ENDSTOPS 4,6
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE0 // ENDSTOPS 3,5
#define Z_MAX_PIN PE1 // ENDSTOPS 4,6
//
// Steppers
//
#define X_STEP_PIN PC6
#define X_DIR_PIN PD13
#define X_ENABLE_PIN PA8
#define X_STEP_PIN PC6
#define X_DIR_PIN PD13
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PA12
#define Y_DIR_PIN PA11
#define Y_ENABLE_PIN PA15
#define Y_STEP_PIN PA12
#define Y_DIR_PIN PA11
#define Y_ENABLE_PIN PA15
#define Z_STEP_PIN PD6
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
#define Z_STEP_PIN PD6
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
// Extruder stepper pins
// NOTE: Numbering here is made according to EXT connector numbers,
@ -86,46 +86,46 @@
// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step
// stick that drives the EXT0 output on the board.
//
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
//
// Heaters / Fans
//
#define HEATER_0_PIN PB0 // EXT0 port
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
#define HEATER_0_PIN PB0 // EXT0 port
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
//
// These are FAN PWM pins on EXT0..EXT2 connectors.
//
//#define FAN_PIN PB9 // EXT0 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
//#define FAN_PIN PB9 // EXT0 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
//
// Temperature Sensors
//
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
//
// Misc. Functions
//
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
//
// LCD / Controller
@ -139,16 +139,16 @@
// RepRapDiscount Smart Controller, but adds an FFC40 connector
// connected with a flat wire to J2 connector on the board.
//
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
#define LCD_PINS_D5 PD9
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
#define LCD_PINS_D5 PD9
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
#define GTM32_PRO_VB_USE_LCD_BEEPER
#define GTM32_PRO_VB_USE_EXT_SDCARD
@ -157,8 +157,8 @@
//
// Serial LCDs can be implemented in ExtUI
//
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
#endif
#if HAS_GRAPHICAL_LCD
@ -182,10 +182,10 @@
// This is pin 32 on J2 FFC40 and pin, goes to the beeper
// on Geeetech's version of RepRapDiscount Smart Controller
// (e.g. on Rostock 301)
#define BEEPER_PIN PE12
#define BEEPER_PIN PE12
#else
// This is the beeper on the board itself
#define BEEPER_PIN PB10
#define BEEPER_PIN PB10
#endif
/**
@ -203,28 +203,28 @@
//
// SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector
//
#define SS_PIN PC11
#define SCK_PIN PC12
#define MOSI_PIN PD2
#define MISO_PIN PC8
#define SD_DETECT_PIN PC7
#define SS_PIN PC11
#define SCK_PIN PC12
#define MOSI_PIN PD2
#define MISO_PIN PC8
#define SD_DETECT_PIN PC7
#else
//
// Use the on-board card socket labeled TF_CARD_SOCKET
//
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#endif
#define SDSS SS_PIN
#define SDSS SS_PIN
//
// ESP WiFi can be soldered to J9 connector which is wired to USART2.
// Must define WIFISUPPORT in Configuration.h for the printer.
//
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1

130
Marlin/src/pins/stm32f1/pins_GTM32_PRO_VB.h
View File

@ -53,32 +53,32 @@
// Enable EEPROM Emulation for this board as it doesn't have EEPROM
#define FLASH_EEPROM_EMULATION
#define E2END 0xFFF // 4KB
#define E2END 0xFFF // 4KB
//
// Limit Switches
//
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE1 // ENDSTOPS 3,5
#define Z_MAX_PIN PE0 // ENDSTOPS 4,6
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE1 // ENDSTOPS 3,5
#define Z_MAX_PIN PE0 // ENDSTOPS 4,6
//
// Steppers
//
#define X_STEP_PIN PC6
#define X_DIR_PIN PD13
#define X_ENABLE_PIN PA8
#define X_STEP_PIN PC6
#define X_DIR_PIN PD13
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PA12
#define Y_DIR_PIN PA11
#define Y_ENABLE_PIN PA15
#define Y_STEP_PIN PA12
#define Y_DIR_PIN PA11
#define Y_ENABLE_PIN PA15
#define Z_STEP_PIN PD6
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
#define Z_STEP_PIN PD6
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
// Extruder stepper pins
// NOTE: Numbering here is made according to EXT connector numbers,
@ -86,46 +86,46 @@
// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step
// stick that drives the EXT0 output on the board.
//
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
//
// Heaters / Fans
//
#define HEATER_0_PIN PB0 // EXT0 port
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
#define HEATER_0_PIN PB0 // EXT0 port
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
//
// These are FAN PWM pins on EXT0..EXT2 connectors.
//
//#define FAN_PIN PB9 // EXT0 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
//#define FAN_PIN PB9 // EXT0 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
//
// Temperature Sensors
//
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
//
// Misc. Functions
//
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
//
// LCD / Controller
@ -138,19 +138,19 @@
// Geeetech's LCD2004A Control Panel is very much like
// RepRapDiscount Smart Controller, but adds an FFC40 connector
//
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
#define LCD_PINS_D5 PD9
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
#define LCD_PINS_D5 PD9
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#else
//
// Serial LCDs can be implemented in ExtUI
//
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
#endif
#if HAS_GRAPHICAL_LCD
@ -167,9 +167,9 @@
// RepRapDiscount Smart Controller, but adds an FFC40 connector
// connected with a flat wire to J2 connector on the board.
//
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
#define GTM32_PRO_VB_USE_LCD_BEEPER
#define GTM32_PRO_VB_USE_EXT_SDCARD
@ -182,10 +182,10 @@
// This is pin 32 on J2 FFC40 and pin, goes to the beeper
// on Geeetech's version of RepRapDiscount Smart Controller
// (e.g. on Rostock 301)
#define BEEPER_PIN PE12
#define BEEPER_PIN PE12
#else
// This is the beeper on the board itself
#define BEEPER_PIN PB10
#define BEEPER_PIN PB10
#endif
/**
@ -203,28 +203,28 @@
//
// SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector
//
#define SS_PIN PC11
#define SCK_PIN PC12
#define MOSI_PIN PD2
#define MISO_PIN PC8
#define SD_DETECT_PIN PC7
#define SS_PIN PC11
#define SCK_PIN PC12
#define MOSI_PIN PD2
#define MISO_PIN PC8
#define SD_DETECT_PIN PC7
#else
//
// Use the on-board card socket labeled TF_CARD_SOCKET
//
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#endif
#define SDSS SS_PIN
#define SDSS SS_PIN
//
// ESP WiFi can be soldered to J9 connector which is wired to USART2.
// Must define WIFISUPPORT in Configuration.h for the printer.
//
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1

136
Marlin/src/pins/stm32f1/pins_GTM32_REV_B.h
View File

@ -53,32 +53,32 @@
// Enable EEPROM Emulation for this board as it doesn't have EEPROM
#define FLASH_EEPROM_EMULATION
#define E2END 0xFFF // 4KB
#define E2END 0xFFF // 4KB
//
// Limit Switches
//
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE1 // ENDSTOPS 3,5
#define Z_MAX_PIN PE0 // ENDSTOPS 4,6
#define X_MIN_PIN PE5 // ENDSTOPS 15,17
#define X_MAX_PIN PE4 // ENDSTOPS 16,18
#define Y_MIN_PIN PE3 // ENDSTOPS 9,11
#define Y_MAX_PIN PE2 // ENDSTOPS 10,12
#define Z_MIN_PIN PE1 // ENDSTOPS 3,5
#define Z_MAX_PIN PE0 // ENDSTOPS 4,6
//
// Steppers
//
#define X_STEP_PIN PC6
#define X_DIR_PIN PD13
#define X_ENABLE_PIN PA8
#define X_STEP_PIN PC6
#define X_DIR_PIN PD13
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PA12
#define Y_DIR_PIN PA11
#define Y_ENABLE_PIN PA15
#define Y_STEP_PIN PA12
#define Y_DIR_PIN PA11
#define Y_ENABLE_PIN PA15
#define Z_STEP_PIN PD6
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
#define Z_STEP_PIN PD6
#define Z_DIR_PIN PD3
#define Z_ENABLE_PIN PB3
// Extruder stepper pins
// NOTE: Numbering here is made according to EXT connector numbers,
@ -86,46 +86,46 @@
// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step
// stick that drives the EXT0 output on the board.
//
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E0_STEP_PIN PC14
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PC15
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E1_STEP_PIN PA0
#define E1_DIR_PIN PB6
#define E1_ENABLE_PIN PA1
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
#define E2_STEP_PIN PB2
#define E2_DIR_PIN PB11
#define E2_ENABLE_PIN PC4
//
// Heaters / Fans - INFO: Extruders ports are in reverse order. Pin numbers here differ from schematic. Original firmware assumes heater, fan and temp sensor on port EXT0 PB0, PB9, PC2.
//
#define HEATER_0_PIN PB0 // EXT0 port.
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
#define HEATER_0_PIN PB0 // EXT0 port.
#define HEATER_1_PIN PB5 // EXT1 port
#define HEATER_2_PIN PB4 // EXT2 port
#define HEATER_BED_PIN PB1 // CON2X3 hotbed port
//
// These are FAN PWM pins on EXT0..EXT2 connectors.
//
//#define FAN_PIN PB9 // EXT0 port
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
//#define FAN_PIN PB9 // EXT0 port
#define FAN1_PIN PB8 // EXT1 port
#define FAN2_PIN PB7 // EXT2 port
#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan
//
// Temperature Sensors
//
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
#define TEMP_0_PIN PC2 // EXT0 port
#define TEMP_1_PIN PC1 // EXT1 port
#define TEMP_2_PIN PC0 // EXT2 port
#define TEMP_BED_PIN PC3 // CON2X3 hotbed port
//
// Misc. Functions
//
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector
//
// LCD / Controller
@ -140,16 +140,16 @@
// RepRapDiscount Smart Controller, but adds an FFC40 connector
// connected with a flat wire to J2 connector on the board.
//
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
#define LCD_PINS_D5 PD9
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#define LCD_PINS_RS PE6 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE PE14 // SID (MOSI)
#define LCD_PINS_D4 PD8 // SCK (CLK) clock
#define LCD_PINS_D5 PD9
#define LCD_PINS_D6 PD10
#define LCD_PINS_D7 PE15
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
#define BTN_EN1 PE8
#define BTN_EN2 PE9
#define BTN_ENC PE13
//#define GTM32_PRO_VB_USE_LCD_BEEPER
#define GTM32_PRO_VB_USE_EXT_SDCARD
@ -158,19 +158,19 @@
//
// Serial LCDs can be implemented in ExtUI
//
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
//#define LCD_UART_TX PD8
//#define LCD_UART_RX PD9
#endif
#if HAS_GRAPHICAL_LCD
#ifndef ST7920_DELAY_1
#define ST7920_DELAY_1 DELAY_NS(96)
#define ST7920_DELAY_1 DELAY_NS(96)
#endif
#ifndef ST7920_DELAY_2
#define ST7920_DELAY_2 DELAY_NS(48)
#define ST7920_DELAY_2 DELAY_NS(48)
#endif
#ifndef ST7920_DELAY_3
#define ST7920_DELAY_3 DELAY_NS(715)
#define ST7920_DELAY_3 DELAY_NS(715)
#endif
#endif
@ -183,10 +183,10 @@
// This is pin 32 on J2 FFC40 and pin, goes to the beeper
// on Geeetech's version of RepRapDiscount Smart Controller
// (e.g. on Rostock 301)
#define BEEPER_PIN PE12
#define BEEPER_PIN PE12
#else
// This is the beeper on the board itself
#define BEEPER_PIN PB10
#define BEEPER_PIN PB10
#endif
/**
@ -204,29 +204,29 @@
//
// SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector
//
#define SS_PIN PB12 // PC11
#define SCK_PIN PB13 // PC12 // PC1
#define MOSI_PIN PB15 // PD2 // PD2
#define MISO_PIN PB14 // PC8
#define SD_DETECT_PIN PC7
#define SS_PIN PB12 // PC11
#define SCK_PIN PB13 // PC12 // PC1
#define MOSI_PIN PB15 // PD2 // PD2
#define MISO_PIN PB14 // PC8
#define SD_DETECT_PIN PC7
#else
//
// Use the on-board card socket labeled TF_CARD_SOCKET
//
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6 // PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#define SS_PIN PA4
#define SCK_PIN PA5
#define MOSI_PIN PA7
#define MISO_PIN PA6 // PA6
#define SD_DETECT_PIN -1 // Card detect is not connected
#endif
#define SDSS SS_PIN
#define SDSS SS_PIN
//
// ESP WiFi can be soldered to J9 connector which is wired to USART2.
// Must define WIFISUPPORT in Configuration.h for the printer.
//
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1
#define ESP_WIFI_MODULE_COM 2
#define ESP_WIFI_MODULE_BAUDRATE 115200
#define ESP_WIFI_MODULE_RESET_PIN -1

82
Marlin/src/pins/stm32f1/pins_JGAURORA_A5S_A1.h
View File

@ -42,10 +42,10 @@
// #define MCU_STM32F103ZE // not yet required
// Enable EEPROM Emulation for this board, so that we don't overwrite factory data
//#define I2C_EEPROM // AT24C64
//#define E2END 0x7FFF // 64KB
//#define I2C_EEPROM // AT24C64
//#define E2END 0x7FFF // 64KB
//#define FLASH_EEPROM_EMULATION
//#define E2END 0xFFF // 4KB
//#define E2END 0xFFF // 4KB
//#define E2END uint32(EEPROM_START_ADDRESS + (EEPROM_PAGE_SIZE * 2) - 1)
//#define EEPROM_CHITCHAT
//#define DEBUG_EEPROM_READWRITE
@ -53,78 +53,78 @@
//
// Limit Switches
//
#define X_STOP_PIN PC6
#define Y_STOP_PIN PG8
#define Z_STOP_PIN PG7
//#define X_MAX_PIN PC5
//#define Y_MAX_PIN PC4
//#define Z_MAX_PIN PB0
#define X_STOP_PIN PC6
#define Y_STOP_PIN PG8
#define Z_STOP_PIN PG7
//#define X_MAX_PIN PC5
//#define Y_MAX_PIN PC4
//#define Z_MAX_PIN PB0
//
// Steppers
//
#define X_STEP_PIN PD6
#define X_DIR_PIN PD3
#define X_ENABLE_PIN PG9
#define X_STEP_PIN PD6
#define X_DIR_PIN PD3
#define X_ENABLE_PIN PG9
#define Y_STEP_PIN PG12
#define Y_DIR_PIN PG11
#define Y_ENABLE_PIN PG13
#define Y_STEP_PIN PG12
#define Y_DIR_PIN PG11
#define Y_ENABLE_PIN PG13
#define Z_STEP_PIN PG15
#define Z_DIR_PIN PG14
#define Z_ENABLE_PIN PB8
#define Z_STEP_PIN PG15
#define Z_DIR_PIN PG14
#define Z_ENABLE_PIN PB8
#define E0_STEP_PIN PE2
#define E0_DIR_PIN PB9
#define E0_ENABLE_PIN PE3
#define E0_STEP_PIN PE2
#define E0_DIR_PIN PB9
#define E0_ENABLE_PIN PE3
#define E1_STEP_PIN PE5
#define E1_DIR_PIN PE4
#define E1_ENABLE_PIN PE6
#define E1_STEP_PIN PE5
#define E1_DIR_PIN PE4
#define E1_ENABLE_PIN PE6
//
// Temperature Sensors
//
#define TEMP_0_PIN PC2
#define TEMP_BED_PIN PC1
#define TEMP_0_PIN PC2
#define TEMP_BED_PIN PC1
//
// Heaters / Fans
//
#define HEATER_0_PIN PA2
#define HEATER_BED_PIN PA3
#define HEATER_0_PIN PA2
#define HEATER_BED_PIN PA3
#define FAN_PIN PA1
#define FAN_PIN PA1
#define FIL_RUNOUT_PIN PC7
#define FIL_RUNOUT_PIN PC7
//
// LCD
//
#define LCD_BACKLIGHT_PIN PF11
#define FSMC_CS_PIN PD7
#define FSMC_RS_PIN PG0
#define LCD_BACKLIGHT_PIN PF11
#define FSMC_CS_PIN PD7
#define FSMC_RS_PIN PG0
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
#define FSMC_DMA_DEV DMA2
#define FSMC_DMA_CHANNEL DMA_CH5
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
#define FSMC_DMA_DEV DMA2
#define FSMC_DMA_CHANNEL DMA_CH5
//
// SD Card
//
#define SD_DETECT_PIN PF10
#define SD_DETECT_PIN PF10
//
// Misc.
//
#define BEEPER_PIN PC3 // use PB7 to shut up if desired
#define LED_PIN PC13
#define BEEPER_PIN PC3 // use PB7 to shut up if desired
#define LED_PIN PC13
//
// Touch support
//
#if ENABLED(TOUCH_BUTTONS)
#define TOUCH_CS_PIN PA4
#define TOUCH_INT_PIN PC4
#define TOUCH_CS_PIN PA4
#define TOUCH_INT_PIN PC4
#endif

114
Marlin/src/pins/stm32f1/pins_LONGER3D_LK.h
View File

@ -29,20 +29,20 @@
#endif
#define BOARD_INFO_NAME "Longer3D"
#define ALFAWISE_UX0 // Common to all Longer3D STM32F1 boards (used for Open drain mosfets)
#define ALFAWISE_UX0 // Common to all Longer3D STM32F1 boards (used for Open drain mosfets)
//#define DISABLE_DEBUG // We still want to debug with STLINK...
#define DISABLE_JTAG // We free the jtag pins (PA15) but keep STLINK
// Release PB4 (STEP_X_PIN) from JTAG NRST role.
//#define DISABLE_DEBUG // We still want to debug with STLINK...
#define DISABLE_JTAG // We free the jtag pins (PA15) but keep STLINK
// Release PB4 (STEP_X_PIN) from JTAG NRST role.
//
// Limit Switches
//
#define X_MIN_PIN PC1 // pin 16
#define X_MAX_PIN PC0 // pin 15 (Filament sensor on Alfawise setup)
#define Y_MIN_PIN PC15 // pin 9
#define Y_MAX_PIN PC14 // pin 8 (Unused in stock Alfawise setup)
#define Z_MIN_PIN PE6 // pin 5 Standard Endstop or Z_Probe endstop function
#define Z_MAX_PIN PE5 // pin 4 (Unused in stock Alfawise setup)
#define X_MIN_PIN PC1 // pin 16
#define X_MAX_PIN PC0 // pin 15 (Filament sensor on Alfawise setup)
#define Y_MIN_PIN PC15 // pin 9
#define Y_MAX_PIN PC14 // pin 8 (Unused in stock Alfawise setup)
#define Z_MIN_PIN PE6 // pin 5 Standard Endstop or Z_Probe endstop function
#define Z_MAX_PIN PE5 // pin 4 (Unused in stock Alfawise setup)
// May be used for BLTouch Servo function on older variants (<= V08)
#define ONBOARD_ENDSTOPPULLUPS
@ -50,60 +50,60 @@
// Filament Sensor
//
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN PC0 // XMAX plug on PCB used as filament runout sensor on Alfawise boards (inverting true)
#define FIL_RUNOUT_PIN PC0 // XMAX plug on PCB used as filament runout sensor on Alfawise boards (inverting true)
#endif
//
// Steppers
//
#define X_ENABLE_PIN PB5 // pin 91
#define X_STEP_PIN PB4 // pin 90
#define X_DIR_PIN PB3 // pin 89
#define X_ENABLE_PIN PB5 // pin 91
#define X_STEP_PIN PB4 // pin 90
#define X_DIR_PIN PB3 // pin 89
#define Y_ENABLE_PIN PB8 // pin 95
#define Y_STEP_PIN PB7 // pin 93
#define Y_DIR_PIN PB6 // pin 92
#define Y_ENABLE_PIN PB8 // pin 95
#define Y_STEP_PIN PB7 // pin 93
#define Y_DIR_PIN PB6 // pin 92
#define Z_ENABLE_PIN PE1 // pin 98
#define Z_STEP_PIN PE0 // pin 97
#define Z_DIR_PIN PB9 // pin 96
#define Z_ENABLE_PIN PE1 // pin 98
#define Z_STEP_PIN PE0 // pin 97
#define Z_DIR_PIN PB9 // pin 96
#define E0_ENABLE_PIN PE4 // pin 3
#define E0_STEP_PIN PE3 // pin 2
#define E0_DIR_PIN PE2 // pin 1
#define E0_ENABLE_PIN PE4 // pin 3
#define E0_STEP_PIN PE3 // pin 2
#define E0_DIR_PIN PE2 // pin 1
//
// Temperature Sensors
//
#define TEMP_0_PIN PA0 // pin 23 (Nozzle 100K/3950 thermistor)
#define TEMP_BED_PIN PA1 // pin 24 (Hot Bed 100K/3950 thermistor)
#define TEMP_0_PIN PA0 // pin 23 (Nozzle 100K/3950 thermistor)
#define TEMP_BED_PIN PA1 // pin 24 (Hot Bed 100K/3950 thermistor)
//
// Heaters / Fans
//
#define HEATER_0_PIN PD3 // pin 84 (Nozzle Heat Mosfet)
#define HEATER_BED_PIN PA8 // pin 67 (Hot Bed Mosfet)
#define HEATER_0_PIN PD3 // pin 84 (Nozzle Heat Mosfet)
#define HEATER_BED_PIN PA8 // pin 67 (Hot Bed Mosfet)
#define FAN_PIN PA15 // pin 77 (4cm Fan)
#define FAN_SOFT_PWM // Required to avoid issues with heating or STLink
#define FAN_MIN_PWM 35 // Fan will not start in 1-30 range
#define FAN_MAX_PWM 255
#define FAN_PIN PA15 // pin 77 (4cm Fan)
#define FAN_SOFT_PWM // Required to avoid issues with heating or STLink
#define FAN_MIN_PWM 35 // Fan will not start in 1-30 range
#define FAN_MAX_PWM 255
//#define BEEPER_PIN PD13 // pin 60 (Servo PWM output 5V/GND on Board V0G+) made for BL-Touch sensor
//#define BEEPER_PIN PD13 // pin 60 (Servo PWM output 5V/GND on Board V0G+) made for BL-Touch sensor
// Can drive a PC Buzzer, if connected between PWM and 5V pins
#define LED_PIN PC2 // pin 17
#define LED_PIN PC2 // pin 17
//
// PWM for a servo probe
// Other servo devices are not supported on this board!
//
#if HAS_Z_SERVO_PROBE
#define SERVO0_PIN PD13 // Open drain PWM pin on the V0G (GND or floating 5V)
#define SERVO0_PWM_OD // Comment this if using PE5
#define SERVO0_PIN PD13 // Open drain PWM pin on the V0G (GND or floating 5V)
#define SERVO0_PWM_OD // Comment this if using PE5
//#define SERVO0_PIN PE5 // Pulled up PWM pin on the V08 (3.3V or 0)
//#undef Z_MAX_PIN // Uncomment if using ZMAX connector (PE5)
//#define SERVO0_PIN PE5 // Pulled up PWM pin on the V08 (3.3V or 0)
//#undef Z_MAX_PIN // Uncomment if using ZMAX connector (PE5)
#endif
/**
@ -118,17 +118,17 @@
* because Marlin uses the reset as a failsafe to revive a glitchy LCD.
*/
#define LCD_RESET_PIN PC4 // pin 33
#define LCD_BACKLIGHT_PIN PD12 // pin 59
#define FSMC_CS_PIN PD7 // pin 88 = FSMC_NE1
#define FSMC_RS_PIN PD11 // pin 58 A16 Register. Only one address needed
#define LCD_RESET_PIN PC4 // pin 33
#define LCD_BACKLIGHT_PIN PD12 // pin 59
#define FSMC_CS_PIN PD7 // pin 88 = FSMC_NE1
#define FSMC_RS_PIN PD11 // pin 58 A16 Register. Only one address needed
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
#define FSMC_DMA_DEV DMA2
#define FSMC_DMA_CHANNEL DMA_CH5
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
#define FSMC_DMA_DEV DMA2
#define FSMC_DMA_CHANNEL DMA_CH5
#define DOGLCD_MOSI -1 // Prevent auto-define by Conditionals_post.h
#define DOGLCD_SCK -1
#define DOGLCD_MOSI -1 // Prevent auto-define by Conditionals_post.h
#define DOGLCD_SCK -1
/**
* Note: Alfawise U20/U30 boards DON'T use SPI2, as the hardware designer
@ -136,11 +136,11 @@
* declared below.
*/
#if ENABLED(TOUCH_BUTTONS)
#define TOUCH_CS_PIN PB12 // pin 51 SPI2_NSS
#define TOUCH_SCK_PIN PB13 // pin 52
#define TOUCH_MOSI_PIN PB14 // pin 53
#define TOUCH_MISO_PIN PB15 // pin 54
#define TOUCH_INT_PIN PC6 // pin 63 (PenIRQ coming from ADS7843)
#define TOUCH_CS_PIN PB12 // pin 51 SPI2_NSS
#define TOUCH_SCK_PIN PB13 // pin 52
#define TOUCH_MOSI_PIN PB14 // pin 53
#define TOUCH_MISO_PIN PB15 // pin 54
#define TOUCH_INT_PIN PC6 // pin 63 (PenIRQ coming from ADS7843)
#endif
//
@ -153,12 +153,12 @@
#undef E2END
#if ENABLED(SPI_EEPROM)
// SPI1 EEPROM Winbond W25Q64 (8MB/64Mbits)
#define SPI_CHAN_EEPROM1 1
#define SPI_EEPROM1_CS PC5 // pin 34
#define EEPROM_SCK BOARD_SPI1_SCK_PIN // PA5 pin 30
#define EEPROM_MISO BOARD_SPI1_MISO_PIN // PA6 pin 31
#define EEPROM_MOSI BOARD_SPI1_MOSI_PIN // PA7 pin 32
#define EEPROM_PAGE_SIZE 0x1000U // 4KB (from datasheet)
#define SPI_CHAN_EEPROM1 1
#define SPI_EEPROM1_CS PC5 // pin 34
#define EEPROM_SCK BOARD_SPI1_SCK_PIN // PA5 pin 30
#define EEPROM_MISO BOARD_SPI1_MISO_PIN // PA6 pin 31
#define EEPROM_MOSI BOARD_SPI1_MOSI_PIN // PA7 pin 32
#define EEPROM_PAGE_SIZE 0x1000U // 4KB (from datasheet)
#define E2END ((16 * EEPROM_PAGE_SIZE)-1) // Limit to 64KB for now...
#elif ENABLED(FLASH_EEPROM_EMULATION)
// SoC Flash (framework-arduinoststm32-maple/STM32F1/libraries/EEPROM/EEPROM.h)

46
Marlin/src/pins/stm32f1/pins_MALYAN_M200.h
View File

@ -36,7 +36,7 @@
// but it is literally the only board which uses it.
#define FLASH_EEPROM_EMULATION
#define SDSS SS_PIN
#define SDSS SS_PIN
// Based on PWM timer usage, we have to use these timers and soft PWM for the fans
// On STM32F103:
@ -50,43 +50,43 @@
//
// Limit Switches
//
#define X_MIN_PIN PB4
#define Y_MIN_PIN PA15
#define Z_MIN_PIN PB5
#define X_MIN_PIN PB4
#define Y_MIN_PIN PA15
#define Z_MIN_PIN PB5
//
// Steppers
//
// X & Y enable are the same
#define X_STEP_PIN PB14
#define X_DIR_PIN PB15
#define X_ENABLE_PIN PA8
#define X_STEP_PIN PB14
#define X_DIR_PIN PB15
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PB12
#define Y_DIR_PIN PB13
#define Y_ENABLE_PIN PA8
#define Y_STEP_PIN PB12
#define Y_DIR_PIN PB13
#define Y_ENABLE_PIN PA8
#define Z_STEP_PIN PB10
#define Z_DIR_PIN PB2
#define Z_ENABLE_PIN PB11
#define Z_STEP_PIN PB10
#define Z_DIR_PIN PB2
#define Z_ENABLE_PIN PB11
#define E0_STEP_PIN PB0
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PB1
#define E0_STEP_PIN PB0
#define E0_DIR_PIN PC13
#define E0_ENABLE_PIN PB1
//
// Temperature Sensors
//
#define TEMP_0_PIN PA0 // Analog Input (HOTEND0 thermistor)
#define TEMP_BED_PIN PA1 // Analog Input (BED thermistor)
#define TEMP_0_PIN PA0 // Analog Input (HOTEND0 thermistor)
#define TEMP_BED_PIN PA1 // Analog Input (BED thermistor)
//
// Heaters / Fans
//
#define HEATER_0_PIN PB6 // HOTEND0 MOSFET
#define HEATER_BED_PIN PB7 // BED MOSFET
#define HEATER_0_PIN PB6 // HOTEND0 MOSFET
#define HEATER_BED_PIN PB7 // BED MOSFET
#define MALYAN_FAN1_PIN PB8 // FAN1 header on board - PRINT FAN
#define MALYAN_FAN2_PIN PB3 // FAN2 header on board - CONTROLLER FAN
#define MALYAN_FAN1_PIN PB8 // FAN1 header on board - PRINT FAN
#define MALYAN_FAN2_PIN PB3 // FAN2 header on board - CONTROLLER FAN
#define FAN1_PIN MALYAN_FAN2_PIN
#define FAN1_PIN MALYAN_FAN2_PIN

124
Marlin/src/pins/stm32f1/pins_MKS_ROBIN.h
View File

@ -43,72 +43,72 @@
//
// Servos
//
#define SERVO0_PIN PC3 // XS1 - 5
#define SERVO1_PIN PA1 // XS1 - 6
#define SERVO2_PIN PF9 // XS2 - 5
#define SERVO3_PIN PF8 // XS2 - 6
#define SERVO0_PIN PC3 // XS1 - 5
#define SERVO1_PIN PA1 // XS1 - 6
#define SERVO2_PIN PF9 // XS2 - 5
#define SERVO3_PIN PF8 // XS2 - 6
//
// Limit Switches
//
#define X_MIN_PIN PB12
#define X_MAX_PIN PB0
#define Y_MIN_PIN PC5
#define Y_MAX_PIN PC4
#define Z_MIN_PIN PA4
#define Z_MAX_PIN PF7
#define X_MIN_PIN PB12
#define X_MAX_PIN PB0
#define Y_MIN_PIN PC5
#define Y_MAX_PIN PC4
#define Z_MIN_PIN PA4
#define Z_MAX_PIN PF7
//
// Steppers
//
#define X_ENABLE_PIN PB9
#define X_STEP_PIN PB8
#define X_DIR_PIN PB5
#define X_ENABLE_PIN PB9
#define X_STEP_PIN PB8
#define X_DIR_PIN PB5
#define Y_ENABLE_PIN PB4
#define Y_STEP_PIN PG15
#define Y_DIR_PIN PG10
#define Y_ENABLE_PIN PB4
#define Y_STEP_PIN PG15
#define Y_DIR_PIN PG10
#define Z_ENABLE_PIN PD7
#define Z_STEP_PIN PD3
#define Z_DIR_PIN PG14
#define Z_ENABLE_PIN PD7
#define Z_STEP_PIN PD3
#define Z_DIR_PIN PG14
#define E0_ENABLE_PIN PG13
#define E0_STEP_PIN PG8
#define E0_DIR_PIN PA15
#define E0_ENABLE_PIN PG13
#define E0_STEP_PIN PG8
#define E0_DIR_PIN PA15
#define E1_ENABLE_PIN PA12
#define E1_STEP_PIN PA11
#define E1_DIR_PIN PA8
#define E1_ENABLE_PIN PA12
#define E1_STEP_PIN PA11
#define E1_DIR_PIN PA8
//
// Temperature Sensors
//
#define TEMP_0_PIN PC1 // TH1
#define TEMP_1_PIN PC2 // TH2
#define TEMP_BED_PIN PC0 // TB1
#define TEMP_0_PIN PC1 // TH1
#define TEMP_1_PIN PC2 // TH2
#define TEMP_BED_PIN PC0 // TB1
//
// Heaters / Fans
//
#define HEATER_0_PIN PC7 // HEATER1
#define HEATER_1_PIN PA6 // HEATER2
#define HEATER_BED_PIN PC6 // HOT BED
#define HEATER_0_PIN PC7 // HEATER1
#define HEATER_1_PIN PA6 // HEATER2
#define HEATER_BED_PIN PC6 // HOT BED
#define FAN_PIN PA7 // FAN
#define FAN_PIN PA7 // FAN
/**
* Note: MKS Robin board is using SPI2 interface. Make sure your stm32duino library is configured accordingly
*/
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
//#define MAX6675_SS_PIN PE6 // TC2 - CS2
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
//#define MAX6675_SS_PIN PE6 // TC2 - CS2
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PA3 // PW_OFF
#define FIL_RUNOUT_PIN PF11 // MT_DET
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PA3 // PW_OFF
#define FIL_RUNOUT_PIN PF11 // MT_DET
#define BEEPER_PIN PC13
#define LED_PIN PB2
#define BEEPER_PIN PC13
#define LED_PIN PB2
/**
* Note: MKS Robin TFT screens use various TFT controllers
@ -122,38 +122,38 @@
* Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu
* because Marlin uses the reset as a failsafe to revive a glitchy LCD.
*/
//#define LCD_RESET_PIN PF6
#define LCD_BACKLIGHT_PIN PG11
#define FSMC_CS_PIN PG12 // NE4
#define FSMC_RS_PIN PF0 // A0
//#define LCD_RESET_PIN PF6
#define LCD_BACKLIGHT_PIN PG11
#define FSMC_CS_PIN PG12 // NE4
#define FSMC_RS_PIN PF0 // A0
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
#define FSMC_DMA_DEV DMA2
#define FSMC_DMA_CHANNEL DMA_CH5
#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT
#define FSMC_DMA_DEV DMA2
#define FSMC_DMA_CHANNEL DMA_CH5
#if ENABLED(TOUCH_BUTTONS)
#define TOUCH_CS_PIN PB1 // SPI2_NSS
#define TOUCH_SCK_PIN PB13 // SPI2_SCK
#define TOUCH_MISO_PIN PB14 // SPI2_MISO
#define TOUCH_MOSI_PIN PB15 // SPI2_MOSI
#define TOUCH_CS_PIN PB1 // SPI2_NSS
#define TOUCH_SCK_PIN PB13 // SPI2_SCK
#define TOUCH_MISO_PIN PB14 // SPI2_MISO
#define TOUCH_MOSI_PIN PB15 // SPI2_MOSI
#endif
// SPI1(PA7) & SPI3(PB5) not available
#define ENABLE_SPI2
#if ENABLED(SDIO_SUPPORT)
#define SCK_PIN PB13 // SPI2
#define MISO_PIN PB14 // SPI2
#define MOSI_PIN PB15 // SPI2
#define SS_PIN -1 // PB12 is X-
#define SD_DETECT_PIN PF12 // SD_CD
#define SCK_PIN PB13 // SPI2
#define MISO_PIN PB14 // SPI2
#define MOSI_PIN PB15 // SPI2
#define SS_PIN -1 // PB12 is X-
#define SD_DETECT_PIN PF12 // SD_CD
#else
// SD as custom software SPI (SDIO pins)
#define SCK_PIN PC12
#define MISO_PIN PC8
#define MOSI_PIN PD2
#define SS_PIN -1
#define ONBOARD_SD_CS_PIN PC11
#define SDSS PD2
#define SD_DETECT_PIN -1
#define SCK_PIN PC12
#define MISO_PIN PC8
#define MOSI_PIN PD2
#define SS_PIN -1
#define ONBOARD_SD_CS_PIN PC11
#define SDSS PD2
#define SD_DETECT_PIN -1
#endif

94
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_LITE.h
View File

@ -39,74 +39,74 @@
//
// Limit Switches
//
#define X_STOP_PIN PC13
#define Y_STOP_PIN PC0
#define Z_MIN_PIN PC12
#define Z_MAX_PIN PB9
#define X_STOP_PIN PC13
#define Y_STOP_PIN PC0
#define Z_MIN_PIN PC12
#define Z_MAX_PIN PB9
//
// Steppers
//
#define X_STEP_PIN PC6
#define X_DIR_PIN PB12
#define X_ENABLE_PIN PB10
#define X_STEP_PIN PC6
#define X_DIR_PIN PB12
#define X_ENABLE_PIN PB10
#define Y_STEP_PIN PB11
#define Y_DIR_PIN PB2
#define Y_ENABLE_PIN PB10
#define Y_STEP_PIN PB11
#define Y_DIR_PIN PB2
#define Y_ENABLE_PIN PB10
#define Z_STEP_PIN PB1
#define Z_DIR_PIN PC5
#define Z_ENABLE_PIN PB10
#define Z_STEP_PIN PB1
#define Z_DIR_PIN PC5
#define Z_ENABLE_PIN PB10
#define E0_STEP_PIN PC4
#define E0_DIR_PIN PA5
#define E0_ENABLE_PIN PA4
#define E0_STEP_PIN PC4
#define E0_DIR_PIN PA5
#define E0_ENABLE_PIN PA4
//
// Heaters / Fans
//
#define HEATER_0_PIN PC9
#define FAN_PIN PA8
#define HEATER_BED_PIN PC8
#define HEATER_0_PIN PC9
#define FAN_PIN PA8
#define HEATER_BED_PIN PC8
//
// Temperature Sensors
//
#define TEMP_BED_PIN PA1
#define TEMP_0_PIN PA0
#define TEMP_BED_PIN PA1
#define TEMP_0_PIN PA0
#define FIL_RUNOUT_PIN PB8 // MT_DET
#define FIL_RUNOUT_PIN PB8 // MT_DET
//
// LCD Pins
//
#if HAS_SPI_LCD
#define BEEPER_PIN PD2
#define BTN_ENC PB3
#define LCD_PINS_RS PC3
#define BEEPER_PIN PD2
#define BTN_ENC PB3
#define LCD_PINS_RS PC3
#define BTN_EN1 PB5
#define BTN_EN2 PB4
#define BTN_EN1 PB5
#define BTN_EN2 PB4
#define LCD_PINS_ENABLE PC2
#define LCD_PINS_ENABLE PC2
#if ENABLED(MKS_MINI_12864)
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN -1
#define DOGLCD_A0 PC1
#define DOGLCD_CS PC2
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN -1
#define DOGLCD_A0 PC1
#define DOGLCD_CS PC2
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
#else // !MKS_MINI_12864
#else // !MKS_MINI_12864
#define LCD_PINS_D4 PC1
#define LCD_PINS_D4 PC1
#if ENABLED(ULTIPANEL)
#define LCD_PINS_D5 -1
#define LCD_PINS_D6 -1
#define LCD_PINS_D7 -1
#define LCD_PINS_D5 -1
#define LCD_PINS_D6 -1
#define LCD_PINS_D7 -1
#endif
#endif // !MKS_MINI_12864
@ -114,9 +114,9 @@
#endif // HAS_SPI_LCD
// Motor current PWM pins
#define MOTOR_CURRENT_PWM_XY_PIN PB0
#define MOTOR_CURRENT_PWM_Z_PIN PA7
#define MOTOR_CURRENT_PWM_E_PIN PA6
#define MOTOR_CURRENT_PWM_XY_PIN PB0
#define MOTOR_CURRENT_PWM_Z_PIN PA7
#define MOTOR_CURRENT_PWM_E_PIN PA6
#define MOTOR_CURRENT_PWM_RANGE (65535/10/3.3) // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
#define DEFAULT_PWM_MOTOR_CURRENT { 1000, 1000, 1000 } // 1.05Amp per driver, here is XY, Z and E. This values determined empirically.
@ -124,11 +124,11 @@
// SD Card
//
#define ENABLE_SPI2
#define SD_DETECT_PIN PC10
#define SCK_PIN PB13
#define MISO_PIN P1B4
#define MOSI_PIN P1B5
#define SS_PIN PA15
#define SD_DETECT_PIN PC10
#define SCK_PIN PB13
#define MISO_PIN P1B4
#define MOSI_PIN P1B5
#define SS_PIN PA15
#if HAS_GRAPHICAL_LCD
#define BOARD_ST7920_DELAY_1 DELAY_NS(125)

106
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_LITE3.h
View File

@ -43,89 +43,89 @@
//
// Servos
//
#define SERVO0_PIN PA3
#define SERVO0_PIN PA3
//
// Limit Switches
//
#define X_STOP_PIN PA12
#define Y_STOP_PIN PA11
#define Z_MIN_PIN PC6
#define Z_MAX_PIN PB1
#define X_STOP_PIN PA12
#define Y_STOP_PIN PA11
#define Z_MIN_PIN PC6
#define Z_MAX_PIN PB1
//
// Steppers
//
#define X_STEP_PIN PC0
#define X_DIR_PIN PB2
#define X_ENABLE_PIN PC13
#define X_STEP_PIN PC0
#define X_DIR_PIN PB2
#define X_ENABLE_PIN PC13
#define Y_STEP_PIN PC2
#define Y_DIR_PIN PB9
#define Y_ENABLE_PIN PB12
#define Y_STEP_PIN PC2
#define Y_DIR_PIN PB9
#define Y_ENABLE_PIN PB12
#define Z_STEP_PIN PB7
#define Z_DIR_PIN PB6
#define Z_ENABLE_PIN PB8
#define Z_STEP_PIN PB7
#define Z_DIR_PIN PB6
#define Z_ENABLE_PIN PB8
#define E0_STEP_PIN PB4
#define E0_DIR_PIN PB3
#define E0_ENABLE_PIN PB5
#define E0_STEP_PIN PB4
#define E0_DIR_PIN PB3
#define E0_ENABLE_PIN PB5
#define E1_STEP_PIN PC12
#define E1_DIR_PIN PC11
#define E1_ENABLE_PIN PD2
#define E1_STEP_PIN PC12
#define E1_DIR_PIN PC11
#define E1_ENABLE_PIN PD2
//
// Heaters 0,1 / Fans / Bed
//
#define HEATER_0_PIN PC9
#define HEATER_1_PIN PC7
#define FAN_PIN PA8
#define HEATER_BED_PIN PC8
#define HEATER_0_PIN PC9
#define HEATER_1_PIN PC7
#define FAN_PIN PA8
#define HEATER_BED_PIN PC8
//
// Temperature Sensors
//
#define TEMP_BED_PIN PA1 //TB
#define TEMP_0_PIN PA0 //TH1
#define TEMP_1_PIN PA2 //TH2
#define TEMP_BED_PIN PA1 //TB
#define TEMP_0_PIN PA0 //TH1
#define TEMP_1_PIN PA2 //TH2
#define FIL_RUNOUT_PIN PB10 // MT_DET
#define FIL_RUNOUT_PIN PB10 // MT_DET
//
// LCD Pins
//
#if HAS_SPI_LCD
#define BEEPER_PIN PC1
#define BTN_ENC PC3
#define LCD_PINS_ENABLE PA4
#define LCD_PINS_RS PA5
#define BTN_EN1 PB11
#define BTN_EN2 PB0
#define BEEPER_PIN PC1
#define BTN_ENC PC3
#define LCD_PINS_ENABLE PA4
#define LCD_PINS_RS PA5
#define BTN_EN1 PB11
#define BTN_EN2 PB0
// MKS MINI12864 and MKS LCD12864B; If using MKS LCD12864A (Need to remove RPK2 resistor)
#if ENABLED(MKS_MINI_12864)
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN -1
#define DOGLCD_A0 PC4
#define DOGLCD_CS PA7
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN -1
#define DOGLCD_A0 PC4
#define DOGLCD_CS PA7
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
// Required for MKS_MINI_12864 with this board
#define MKS_LCD12864B
#undef SHOW_BOOTSCREEN
#else // !MKS_MINI_12864
#else // !MKS_MINI_12864
#define LCD_PINS_D4 PA6
#define LCD_PINS_D4 PA6
#if ENABLED(ULTIPANEL)
#define LCD_PINS_D5 PA7
#define LCD_PINS_D6 PC4
#define LCD_PINS_D7 PC5
#define LCD_PINS_D5 PA7
#define LCD_PINS_D6 PC4
#define LCD_PINS_D7 PC5
#endif
#endif // !MKS_MINI_12864
@ -136,18 +136,18 @@
// SD Card
//
#define ENABLE_SPI2
#define SD_DETECT_PIN PC10
#define SCK_PIN PB13
#define MISO_PIN PB14
#define MOSI_PIN PB15
#define SS_PIN PA15
#define SD_DETECT_PIN PC10
#define SCK_PIN PB13
#define MISO_PIN PB14
#define MOSI_PIN PB15
#define SS_PIN PA15
#ifndef ST7920_DELAY_1
#define ST7920_DELAY_1 DELAY_NS(125)
#define ST7920_DELAY_1 DELAY_NS(125)
#endif
#ifndef ST7920_DELAY_2
#define ST7920_DELAY_2 DELAY_NS(125)
#define ST7920_DELAY_2 DELAY_NS(125)
#endif
#ifndef ST7920_DELAY_3
#define ST7920_DELAY_3 DELAY_NS(125)
#define ST7920_DELAY_3 DELAY_NS(125)
#endif

90
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_MINI.h
View File

@ -52,67 +52,67 @@
//
// Limit Switches
//
#define X_STOP_PIN PA15
#define Y_STOP_PIN PA12
#define Z_MIN_PIN PA11
#define Z_MAX_PIN PC4
#define X_STOP_PIN PA15
#define Y_STOP_PIN PA12
#define Z_MIN_PIN PA11
#define Z_MAX_PIN PC4
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN PA4 // MT_DET
#define FIL_RUNOUT_PIN PA4 // MT_DET
#endif
//
// Steppers
//
#define X_ENABLE_PIN PE4
#define X_STEP_PIN PE3
#define X_DIR_PIN PE2
#define X_ENABLE_PIN PE4
#define X_STEP_PIN PE3
#define X_DIR_PIN PE2
#define Y_ENABLE_PIN PE1
#define Y_STEP_PIN PE0
#define Y_DIR_PIN PB9
#define Y_ENABLE_PIN PE1
#define Y_STEP_PIN PE0
#define Y_DIR_PIN PB9
#define Z_ENABLE_PIN PB8
#define Z_STEP_PIN PB5
#define Z_DIR_PIN PB4
#define Z_ENABLE_PIN PB8
#define Z_STEP_PIN PB5
#define Z_DIR_PIN PB4
#define E0_ENABLE_PIN PB3
#define E0_STEP_PIN PD6
#define E0_DIR_PIN PD3
#define E0_ENABLE_PIN PB3
#define E0_STEP_PIN PD6
#define E0_DIR_PIN PD3
//
// Temperature Sensors
//
#define TEMP_0_PIN PC1 // TH1
#define TEMP_BED_PIN PC0 // TB1
#define TEMP_0_PIN PC1 // TH1
#define TEMP_BED_PIN PC0 // TB1
//
// Heaters / Fans
//
#define HEATER_0_PIN PC3 // HEATER1
#define HEATER_BED_PIN PA0 // HOT BED
#define HEATER_0_PIN PC3 // HEATER1
#define HEATER_BED_PIN PA0 // HOT BED
#define FAN_PIN PB1 // FAN
#define FAN_PIN PB1 // FAN
//
// Thermocouples
//
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
//#define MAX6675_SS_PIN PE6 // TC2 - CS2
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
//#define MAX6675_SS_PIN PE6 // TC2 - CS2
//
// Misc. Functions
//
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PA3 // PW_OFF
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PA3 // PW_OFF
//#define LED_PIN PB2
//#define LED_PIN PB2
//
// LCD / Controller
//
#define BEEPER_PIN PC5
#define SD_DETECT_PIN PD12
#define BEEPER_PIN PC5
#define SD_DETECT_PIN PD12
/**
* Note: MKS Robin TFT screens use various TFT controllers.
@ -120,27 +120,27 @@
* to let the bootloader init the screen.
*/
#if ENABLED(FSMC_GRAPHICAL_TFT)
#define FSMC_CS_PIN PD7 // NE4
#define FSMC_RS_PIN PD11 // A0
#define FSMC_CS_PIN PD7 // NE4
#define FSMC_RS_PIN PD11 // A0
#define LCD_RESET_PIN PC6
#define NO_LCD_REINIT // Suppress LCD re-initialization
#define LCD_RESET_PIN PC6
#define NO_LCD_REINIT // Suppress LCD re-initialization
#define LCD_BACKLIGHT_PIN PD13
#define LCD_BACKLIGHT_PIN PD13
#if ENABLED(TOUCH_BUTTONS)
#define TOUCH_CS_PIN PC2
#define TOUCH_SCK_PIN PB13
#define TOUCH_MOSI_PIN PB15
#define TOUCH_MISO_PIN PB14
#define TOUCH_CS_PIN PC2
#define TOUCH_SCK_PIN PB13
#define TOUCH_MOSI_PIN PB15
#define TOUCH_MISO_PIN PB14
#endif
#endif
// Motor current PWM pins
#define MOTOR_CURRENT_PWM_XY_PIN PA6
#define MOTOR_CURRENT_PWM_Z_PIN PA7
#define MOTOR_CURRENT_PWM_E_PIN PB0
#define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
#define MOTOR_CURRENT_PWM_XY_PIN PA6
#define MOTOR_CURRENT_PWM_Z_PIN PA7
#define MOTOR_CURRENT_PWM_E_PIN PB0
#define MOTOR_CURRENT_PWM_RANGE 1500 // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp
#define DEFAULT_PWM_MOTOR_CURRENT { 1030, 1030, 1030 } // 1.05Amp per driver, here is XY, Z and E. This values determined empirically.
// This is a kind of workaround in case native marlin "digipot" interface won't work.
@ -149,6 +149,6 @@
// #define MKS_ROBIN_MINI_VREF_PWM
//#endif
//#define VREF_XY_PIN PA6
//#define VREF_Z_PIN PA7
//#define VREF_E1_PIN PB0
//#define VREF_XY_PIN PA6
//#define VREF_Z_PIN PA7
//#define VREF_E1_PIN PB0

86
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO.h
View File

@ -41,78 +41,78 @@
//
// Limit Switches
//
#define X_STOP_PIN PA15
#define Y_STOP_PIN PA12
#define Z_MIN_PIN PA11
#define Z_MAX_PIN PC4
#define X_STOP_PIN PA15
#define Y_STOP_PIN PA12
#define Z_MIN_PIN PA11
#define Z_MAX_PIN PC4
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN PA4 // MT_DET
#define FIL_RUNOUT_PIN PA4 // MT_DET
#endif
//
// Steppers
//
#define X_ENABLE_PIN PE4
#define X_STEP_PIN PE3
#define X_DIR_PIN PE2
#define X_ENABLE_PIN PE4
#define X_STEP_PIN PE3
#define X_DIR_PIN PE2
#define Y_ENABLE_PIN PE1
#define Y_STEP_PIN PE0
#define Y_DIR_PIN PB9
#define Y_ENABLE_PIN PE1
#define Y_STEP_PIN PE0
#define Y_DIR_PIN PB9
#define Z_ENABLE_PIN PB8
#define Z_STEP_PIN PB5
#define Z_DIR_PIN PB4
#define Z_ENABLE_PIN PB8
#define Z_STEP_PIN PB5
#define Z_DIR_PIN PB4
#define E0_ENABLE_PIN PB3
#define E0_STEP_PIN PD6
#define E0_DIR_PIN PD3
#define E0_ENABLE_PIN PB3
#define E0_STEP_PIN PD6
#define E0_DIR_PIN PD3
#define E1_ENABLE_PIN PA3
#define E1_STEP_PIN PA6
#define E1_DIR_PIN PA1
#define E1_ENABLE_PIN PA3
#define E1_STEP_PIN PA6
#define E1_DIR_PIN PA1
//
// Temperature Sensors
//
#define TEMP_0_PIN PC1 // TH1
#define TEMP_1_PIN PC2 // TH2
#define TEMP_BED_PIN PC0 // TB1
#define TEMP_0_PIN PC1 // TH1
#define TEMP_1_PIN PC2 // TH2
#define TEMP_BED_PIN PC0 // TB1
//
// Heaters / Fans
//
#define HEATER_0_PIN PC3 // HEATER1
#define HEATER_1_PIN PB0 // HEATER2
#define HEATER_BED_PIN PA0 // HOT BED
#define HEATER_0_PIN PC3 // HEATER1
#define HEATER_1_PIN PB0 // HEATER2
#define HEATER_BED_PIN PA0 // HOT BED
#define FAN_PIN PB1 // FAN
#define FAN_PIN PB1 // FAN
//
// Thermocouples
//
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
//#define MAX6675_SS_PIN PE6 // TC2 - CS2
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
//#define MAX6675_SS_PIN PE6 // TC2 - CS2
//
// Misc. Functions
//
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PA3 // PW_OFF
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PA3 // PW_OFF
#define LED_PIN PB2
#define LED_PIN PB2
//
// SD Card
//
#define SDIO_SUPPORT
#define SD_DETECT_PIN PD12
#define SD_DETECT_PIN PD12
//
// LCD / Controller
//
#define BEEPER_PIN PC5
#define BEEPER_PIN PC5
/**
* Note: MKS Robin TFT screens use various TFT controllers.
@ -120,18 +120,18 @@
* to let the bootloader init the screen.
*/
#if ENABLED(FSMC_GRAPHICAL_TFT)
#define FSMC_CS_PIN PD7 // NE4
#define FSMC_RS_PIN PD11 // A0
#define FSMC_CS_PIN PD7 // NE4
#define FSMC_RS_PIN PD11 // A0
#define LCD_RESET_PIN PC6 // FSMC_RST
#define NO_LCD_REINIT // Suppress LCD re-initialization
#define LCD_RESET_PIN PC6 // FSMC_RST
#define NO_LCD_REINIT // Suppress LCD re-initialization
#define LCD_BACKLIGHT_PIN PD13
#define LCD_BACKLIGHT_PIN PD13
#if ENABLED(TOUCH_BUTTONS)
#define TOUCH_CS_PIN PA7 // SPI2_NSS
#define TOUCH_SCK_PIN PB13 // SPI2_SCK
#define TOUCH_MISO_PIN PB14 // SPI2_MISO
#define TOUCH_MOSI_PIN PB15 // SPI2_MOSI
#define TOUCH_CS_PIN PA7 // SPI2_NSS
#define TOUCH_SCK_PIN PB13 // SPI2_SCK
#define TOUCH_MISO_PIN PB14 // SPI2_MISO
#define TOUCH_MOSI_PIN PB15 // SPI2_MOSI
#endif
#endif

198
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h
View File

@ -47,74 +47,74 @@
//
// Servos
//
#define SERVO0_PIN PA8 // BLTOUCH
#define SERVO0_PIN PA8 // BLTOUCH
//
// Limit Switches
//
#define X_MIN_PIN PA15
#define X_MAX_PIN PG7
#define Y_MIN_PIN PA12
#define Y_MAX_PIN PG8
#define Z_MIN_PIN PA11
#define Z_MAX_PIN PC4
#define X_MIN_PIN PA15
#define X_MAX_PIN PG7
#define Y_MIN_PIN PA12
#define Y_MAX_PIN PG8
#define Z_MIN_PIN PA11
#define Z_MAX_PIN PC4
//
// Steppers
//
#define X_ENABLE_PIN PE4
#define X_STEP_PIN PE3
#define X_DIR_PIN PE2
#define X_ENABLE_PIN PE4
#define X_STEP_PIN PE3
#define X_DIR_PIN PE2
#ifndef X_CS_PIN
#define X_CS_PIN PF8
#define X_CS_PIN PF8
#endif
#define Y_ENABLE_PIN PE1
#define Y_STEP_PIN PE0
#define Y_DIR_PIN PB9
#define Y_ENABLE_PIN PE1
#define Y_STEP_PIN PE0
#define Y_DIR_PIN PB9
#ifndef Y_CS_PIN
#define Y_CS_PIN PF3
#define Y_CS_PIN PF3
#endif
#define Z_ENABLE_PIN PB8
#define Z_STEP_PIN PB5
#define Z_DIR_PIN PB4
#define Z_ENABLE_PIN PB8
#define Z_STEP_PIN PB5
#define Z_DIR_PIN PB4
#ifndef Z_CS_PIN
#define Z_CS_PIN PF6
#define Z_CS_PIN PF6
#endif
#define E0_ENABLE_PIN PB3
#define E0_STEP_PIN PD6
#define E0_DIR_PIN PD3
#define E0_ENABLE_PIN PB3
#define E0_STEP_PIN PD6
#define E0_DIR_PIN PD3
#ifndef E0_CS_PIN
#define E0_CS_PIN PG15
#define E0_CS_PIN PG15
#endif
#define E1_ENABLE_PIN PA3
#define E1_STEP_PIN PA6
#define E1_DIR_PIN PA1
#define E1_ENABLE_PIN PA3
#define E1_STEP_PIN PA6
#define E1_DIR_PIN PA1
#ifndef E1_CS_PIN
#define E1_CS_PIN PG10
#define E1_CS_PIN PG10
#endif
#define E2_ENABLE_PIN PF0
#define E2_STEP_PIN PF2
#define E2_DIR_PIN PF1
#define E2_ENABLE_PIN PF0
#define E2_STEP_PIN PF2
#define E2_DIR_PIN PF1
#ifndef E2_CS_PIN
#define E2_CS_PIN PG9
#define E2_CS_PIN PG9
#endif
//
// Software SPI pins for TMC2130 stepper drivers
//
#if ENABLED(TMC_USE_SW_SPI)
#ifndef TMC_SW_MOSI
#define TMC_SW_MOSI PB15
#define TMC_SW_MOSI PB15
#endif
#ifndef TMC_SW_MISO
#define TMC_SW_MISO PB14
#define TMC_SW_MISO PB14
#endif
#ifndef TMC_SW_SCK
#define TMC_SW_SCK PB13
#define TMC_SW_SCK PB13
#endif
#endif
@ -140,71 +140,71 @@
//
// Software serial
//
#define X_SERIAL_TX_PIN PF7
#define X_SERIAL_RX_PIN PF8
#define X_SERIAL_TX_PIN PF7
#define X_SERIAL_RX_PIN PF8
#define Y_SERIAL_TX_PIN PF4
#define Y_SERIAL_RX_PIN PF3
#define Y_SERIAL_TX_PIN PF4
#define Y_SERIAL_RX_PIN PF3
#define Z_SERIAL_TX_PIN PF5
#define Z_SERIAL_RX_PIN PF6
#define Z_SERIAL_TX_PIN PF5
#define Z_SERIAL_RX_PIN PF6
#define E0_SERIAL_TX_PIN PG13
#define E0_SERIAL_RX_PIN PG15
#define E0_SERIAL_TX_PIN PG13
#define E0_SERIAL_RX_PIN PG15
#define E1_SERIAL_TX_PIN PG12
#define E1_SERIAL_RX_PIN PG10
#define E1_SERIAL_TX_PIN PG12
#define E1_SERIAL_RX_PIN PG10
#define E2_SERIAL_TX_PIN PC13
#define E2_SERIAL_RX_PIN PG9
#define E2_SERIAL_TX_PIN PC13
#define E2_SERIAL_RX_PIN PG9
#endif
//
// Temperature Sensors
//
#define TEMP_0_PIN PC1 // TH1
#define TEMP_1_PIN PC2 // TH2
#define TEMP_2_PIN PC3 // TH3
#define TEMP_BED_PIN PC0 // TB1
#define TEMP_0_PIN PC1 // TH1
#define TEMP_1_PIN PC2 // TH2
#define TEMP_2_PIN PC3 // TH3
#define TEMP_BED_PIN PC0 // TB1
//
// Heaters / Fans
//
#define HEATER_0_PIN PF10 // +HE0-
#define HEATER_1_PIN PB0 // +HE1-
#define HEATER_2_PIN PF9 // +HE2-
#define HEATER_BED_PIN PA0 // +HOT-BED-
#define FAN_PIN PB1 // +FAN-
#define HEATER_0_PIN PF10 // +HE0-
#define HEATER_1_PIN PB0 // +HE1-
#define HEATER_2_PIN PF9 // +HE2-
#define HEATER_BED_PIN PA0 // +HOT-BED-
#define FAN_PIN PB1 // +FAN-
/**
* Note: MKS Robin Pro board is using SPI2 interface. Make sure your stm32duino library is configured accordingly
*/
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
//#define MAX6675_SS_PIN PF11 // TC2 - CS2
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
//#define MAX6675_SS_PIN PF11 // TC2 - CS2
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PG11 // PW_OFF
#define FIL_RUNOUT_PIN PA4 // MT_DET1
//#define FIL_RUNOUT_PIN PE6 // MT_DET2
//#define FIL_RUNOUT_PIN PG14 // MT_DET3
#define POWER_LOSS_PIN PA2 // PW_DET
#define PS_ON_PIN PG11 // PW_OFF
#define FIL_RUNOUT_PIN PA4 // MT_DET1
//#define FIL_RUNOUT_PIN PE6 // MT_DET2
//#define FIL_RUNOUT_PIN PG14 // MT_DET3
//
// SD Card
//
#ifndef SDCARD_CONNECTION
#define SDCARD_CONNECTION ONBOARD
#define SDCARD_CONNECTION ONBOARD
#endif
#if SD_CONNECTION_IS(LCD)
#define ENABLE_SPI2
#define SD_DETECT_PIN PG3
#define SCK_PIN PB13
#define MISO_PIN PB14
#define MOSI_PIN PB15
#define SS_PIN PG6
#define SD_DETECT_PIN PG3
#define SCK_PIN PB13
#define MISO_PIN PB14
#define MOSI_PIN PB15
#define SS_PIN PG6
#elif SD_CONNECTION_IS(ONBOARD)
#define SDIO_SUPPORT
#define SD_DETECT_PIN PD12
#define SD_DETECT_PIN PD12
#elif SD_CONNECTION_IS(CUSTOM_CABLE)
#error "No custom SD drive cable defined for this board."
#endif
@ -215,60 +215,60 @@
* to let the bootloader init the screen.
*/
#if ENABLED(FSMC_GRAPHICAL_TFT)
#define FSMC_CS_PIN PD7 // NE4
#define FSMC_RS_PIN PD11 // A0
#define FSMC_CS_PIN PD7 // NE4
#define FSMC_RS_PIN PD11 // A0
#define LCD_RESET_PIN PF6
#define NO_LCD_REINIT // Suppress LCD re-initialization
#define LCD_RESET_PIN PF6
#define NO_LCD_REINIT // Suppress LCD re-initialization
#define LCD_BACKLIGHT_PIN PD13
#define LCD_BACKLIGHT_PIN PD13
#if ENABLED(TOUCH_BUTTONS)
#define TOUCH_CS_PIN PA7
#define TOUCH_CS_PIN PA7
#else
#define BEEPER_PIN PC5
#define BTN_ENC PG2
#define BTN_EN1 PG5
#define BTN_EN2 PG4
#define BEEPER_PIN PC5
#define BTN_ENC PG2
#define BTN_EN1 PG5
#define BTN_EN2 PG4
#endif
#elif HAS_SPI_LCD
#define BEEPER_PIN PC5
#define BTN_ENC PG2
#define LCD_PINS_ENABLE PG0
#define LCD_PINS_RS PG1
#define BTN_EN1 PG5
#define BTN_EN2 PG4
#define BEEPER_PIN PC5
#define BTN_ENC PG2
#define LCD_PINS_ENABLE PG0
#define LCD_PINS_RS PG1
#define BTN_EN1 PG5
#define BTN_EN2 PG4
// MKS MINI12864 and MKS LCD12864B. If using MKS LCD12864A (Need to remove RPK2 resistor)
#if ENABLED(MKS_MINI_12864)
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN -1
#define DOGLCD_A0 PF12
#define DOGLCD_CS PF15
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN -1
#define DOGLCD_A0 PF12
#define DOGLCD_CS PF15
#define DOGLCD_SCK PB13
#define DOGLCD_MOSI PB15
#else // !MKS_MINI_12864 && !ENDER2_STOCKDISPLAY
#else // !MKS_MINI_12864 && !ENDER2_STOCKDISPLAY
#define LCD_PINS_D4 PF14
#define LCD_PINS_D4 PF14
#if ENABLED(ULTIPANEL)
#define LCD_PINS_D5 PF15
#define LCD_PINS_D6 PF12
#define LCD_PINS_D7 PF13
#define LCD_PINS_D5 PF15
#define LCD_PINS_D6 PF12
#define LCD_PINS_D7 PF13
#endif
#endif // !MKS_MINI_12864 && !ENDER2_STOCKDISPLAY
#endif
#ifndef ST7920_DELAY_1
#define ST7920_DELAY_1 DELAY_NS(125)
#define ST7920_DELAY_1 DELAY_NS(125)
#endif
#ifndef ST7920_DELAY_2
#define ST7920_DELAY_2 DELAY_NS(125)
#define ST7920_DELAY_2 DELAY_NS(125)
#endif
#ifndef ST7920_DELAY_3
#define ST7920_DELAY_3 DELAY_NS(125)
#define ST7920_DELAY_3 DELAY_NS(125)
#endif

46
Marlin/src/pins/stm32f1/pins_MORPHEUS.h
View File

@ -39,53 +39,53 @@
//
// Limit Switches
//
#define X_MIN_PIN PB14
#define Y_MIN_PIN PB13
#define Z_MIN_PIN PB12
#define X_MIN_PIN PB14
#define Y_MIN_PIN PB13
#define Z_MIN_PIN PB12
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN PB9
#define Z_MIN_PROBE_PIN PB9
#endif
//
// Steppers
//
// X & Y enable are the same
#define X_STEP_PIN PB7
#define X_DIR_PIN PB6
#define X_ENABLE_PIN PB8
#define X_STEP_PIN PB7
#define X_DIR_PIN PB6
#define X_ENABLE_PIN PB8
#define Y_STEP_PIN PB5
#define Y_DIR_PIN PB4
#define Y_ENABLE_PIN PB8
#define Y_STEP_PIN PB5
#define Y_DIR_PIN PB4
#define Y_ENABLE_PIN PB8
#define Z_STEP_PIN PA15
#define Z_DIR_PIN PA10
#define Z_ENABLE_PIN PB3
#define Z_STEP_PIN PA15
#define Z_DIR_PIN PA10
#define Z_ENABLE_PIN PB3
#define E0_STEP_PIN PA8
#define E0_DIR_PIN PB15
#define E0_ENABLE_PIN PA9
#define E0_STEP_PIN PA8
#define E0_DIR_PIN PB15
#define E0_ENABLE_PIN PA9
//
// Temperature Sensors
//
#define TEMP_0_PIN PB1 // Analog Input (HOTEND thermistor)
#define TEMP_BED_PIN PB0 // Analog Input (BED thermistor)
#define TEMP_0_PIN PB1 // Analog Input (HOTEND thermistor)
#define TEMP_BED_PIN PB0 // Analog Input (BED thermistor)
//
// Heaters / Fans
//
#define HEATER_0_PIN PA2 // HOTEND MOSFET
#define HEATER_BED_PIN PA0 // BED MOSFET
#define HEATER_0_PIN PA2 // HOTEND MOSFET
#define HEATER_BED_PIN PA0 // BED MOSFET
#define FAN_PIN PA1 // FAN1 header on board - PRINT FAN
#define FAN_PIN PA1 // FAN1 header on board - PRINT FAN
//
// Misc.
//
#define LED_PIN PC13
#define SDSS PA3
#define LED_PIN PC13
#define SDSS PA3

222
Marlin/src/pins/stm32f1/pins_STM32F1R.h
View File

@ -38,61 +38,61 @@
//
// Limit Switches
//
#define X_STOP_PIN PB3
#define Y_STOP_PIN PB4
#define Z_STOP_PIN PB5
#define X_STOP_PIN PB3
#define Y_STOP_PIN PB4
#define Z_STOP_PIN PB5
//
// Steppers
//
#define X_STEP_PIN PC0
#define X_DIR_PIN PC1
#define X_ENABLE_PIN PA8
#define X_STEP_PIN PC0
#define X_DIR_PIN PC1
#define X_ENABLE_PIN PA8
#define Y_STEP_PIN PC2
#define Y_DIR_PIN PC3
#define Y_ENABLE_PIN PA8
#define Y_STEP_PIN PC2
#define Y_DIR_PIN PC3
#define Y_ENABLE_PIN PA8
#define Z_STEP_PIN PC4
#define Z_DIR_PIN PC5
#define Z_ENABLE_PIN PA8
#define Z_STEP_PIN PC4
#define Z_DIR_PIN PC5
#define Z_ENABLE_PIN PA8
#define E0_STEP_PIN PC6
#define E0_DIR_PIN PC7
#define E0_ENABLE_PIN PA8
#define E0_STEP_PIN PC6
#define E0_DIR_PIN PC7
#define E0_ENABLE_PIN PA8
/**
* TODO: Currently using same Enable pin to all steppers.
*/
#define E1_STEP_PIN PC8
#define E1_DIR_PIN PC9
#define E1_ENABLE_PIN PA8
#define E1_STEP_PIN PC8
#define E1_DIR_PIN PC9
#define E1_ENABLE_PIN PA8
#define E2_STEP_PIN PC10
#define E2_DIR_PIN PC11
#define E2_ENABLE_PIN PA8
#define E2_STEP_PIN PC10
#define E2_DIR_PIN PC11
#define E2_ENABLE_PIN PA8
//
// Misc. Functions
//
#define SDSS PA4
#define LED_PIN PD2
#define SDSS PA4
#define LED_PIN PD2
//
// Heaters / Fans
//
#define HEATER_0_PIN PB0 // EXTRUDER 1
#define HEATER_1_PIN PB1
#define HEATER_0_PIN PB0 // EXTRUDER 1
#define HEATER_1_PIN PB1
#define HEATER_BED_PIN PA3 // BED
#define HEATER_BED_PIN PA3 // BED
//
// Temperature Sensors
//
#define TEMP_BED_PIN PA0 // Analog Input
#define TEMP_0_PIN PA1 // Analog Input
#define TEMP_1_PIN PA2 // Analog Input
#define TEMP_BED_PIN PA0 // Analog Input
#define TEMP_0_PIN PA1 // Analog Input
#define TEMP_1_PIN PA2 // Analog Input
//
// LCD Pins
@ -100,25 +100,25 @@
#if HAS_SPI_LCD
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define LCD_PINS_RS 49 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 51 // SID (MOSI)
#define LCD_PINS_D4 52 // SCK (CLK) clock
#define LCD_PINS_RS 49 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 51 // SID (MOSI)
#define LCD_PINS_D4 52 // SCK (CLK) clock
#elif BOTH(NEWPANEL, PANEL_ONE)
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#else
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#if DISABLED(NEWPANEL)
#define BEEPER_PIN 33
#define BEEPER_PIN 33
// Buttons attached to a shift register
// Not wired yet
//#define SHIFT_CLK 38
@ -132,14 +132,14 @@
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
#define BEEPER_PIN 37
#define BEEPER_PIN 37
#define BTN_EN1 31
#define BTN_EN2 33
#define BTN_ENC 35
#define BTN_EN1 31
#define BTN_EN2 33
#define BTN_ENC 35
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
#define LCD_BACKLIGHT_PIN 39
@ -147,112 +147,112 @@
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SD_DETECT_PIN 42
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SD_DETECT_PIN 42
#elif ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 47
#define BTN_EN2 43
#define BTN_ENC 32
#define LCD_SDSS 53
#define SD_DETECT_PIN -1
#define KILL_PIN 41
#define BTN_EN1 47
#define BTN_EN2 43
#define BTN_ENC 32
#define LCD_SDSS 53
#define SD_DETECT_PIN -1
#define KILL_PIN 41
#elif ENABLED(LCD_I2C_VIKI)
#define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_ENC -1
#define LCD_SDSS 53
#define SD_DETECT_PIN 49
#define BTN_ENC -1
#define LCD_SDSS 53
#define SD_DETECT_PIN 49
#elif ANY(VIKI2, miniVIKI)
#define BEEPER_PIN 33
#define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 45
#define DOGLCD_A0 44
#define DOGLCD_CS 45
#define LCD_SCREEN_ROT_180
#define BTN_EN1 22
#define BTN_EN2 7
#define BTN_ENC 39
#define BTN_EN1 22
#define BTN_EN2 7
#define BTN_ENC 39
#define SDSS 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define SDSS 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define KILL_PIN 31
#define KILL_PIN 31
#define STAT_LED_RED_PIN 32
#define STAT_LED_RED_PIN 32
#define STAT_LED_BLUE_PIN 35
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define BTN_EN1 35
#define BTN_EN2 37
#define BTN_ENC 31
#define SD_DETECT_PIN 49
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER_PIN 23
#define DOGLCD_CS 29
#define DOGLCD_A0 27
#define BTN_EN1 35
#define BTN_EN2 37
#define BTN_ENC 31
#define SD_DETECT_PIN 49
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER_PIN 23
#define DOGLCD_CS 29
#define DOGLCD_A0 27
#define LCD_BACKLIGHT_PIN 33
#elif ENABLED(MINIPANEL)
#define BEEPER_PIN 42
#define BEEPER_PIN 42
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 66
#define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65
#define SDSS 53
#define DOGLCD_A0 44
#define DOGLCD_CS 66
#define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65
#define SDSS 53
#define KILL_PIN 64
#define KILL_PIN 64
// GLCD features
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
// The encoder and click button
#define BTN_EN1 40
#define BTN_EN2 63
#define BTN_ENC 59
#define BTN_EN1 40
#define BTN_EN2 63
#define BTN_ENC 59
// not connected to a pin
#define SD_DETECT_PIN 49
#define SD_DETECT_PIN 49
#else
// Beeper on AUX-4
#define BEEPER_PIN 33
#define BEEPER_PIN 33
// Buttons directly attached to AUX-2
#if ENABLED(REPRAPWORLD_KEYPAD)
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SHIFT_OUT 40
#define SHIFT_CLK 44
#define SHIFT_LD 42
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SHIFT_OUT 40
#define SHIFT_CLK 44
#define SHIFT_LD 42
#elif ENABLED(PANEL_ONE)
#define BTN_EN1 59 // AUX2 PIN 3
#define BTN_EN2 63 // AUX2 PIN 4
#define BTN_ENC 49 // AUX3 PIN 7
#define BTN_EN1 59 // AUX2 PIN 3
#define BTN_EN2 63 // AUX2 PIN 4
#define BTN_ENC 49 // AUX3 PIN 7
#else
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31
#endif
#if ENABLED(G3D_PANEL)
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#else
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
#endif
#endif

244
Marlin/src/pins/stm32f1/pins_STM3R_MINI.h
View File

@ -41,72 +41,72 @@
//
// Limit Switches
//
#define X_STOP_PIN PD0
#define Y_STOP_PIN PD1
#define Z_STOP_PIN PD4
#define X_STOP_PIN PD0
#define Y_STOP_PIN PD1
#define Z_STOP_PIN PD4
//
// Steppers
//
#define X_STEP_PIN PE1
#define X_DIR_PIN PE0
#define X_ENABLE_PIN PC0
#define X_STEP_PIN PE1
#define X_DIR_PIN PE0
#define X_ENABLE_PIN PC0
#define Y_STEP_PIN PE3
#define Y_DIR_PIN PE2
#define Y_ENABLE_PIN PC1
#define Y_STEP_PIN PE3
#define Y_DIR_PIN PE2
#define Y_ENABLE_PIN PC1
#define Z_STEP_PIN PE5
#define Z_DIR_PIN PE4
#define Z_ENABLE_PIN PC2
#define Z_STEP_PIN PE5
#define Z_DIR_PIN PE4
#define Z_ENABLE_PIN PC2
#define E0_STEP_PIN PE7
#define E0_DIR_PIN PE6
#define E0_ENABLE_PIN PC3
#define E0_STEP_PIN PE7
#define E0_DIR_PIN PE6
#define E0_ENABLE_PIN PC3
#define E1_STEP_PIN PE9
#define E1_DIR_PIN PE8
#define E1_ENABLE_PIN PC4
#define E1_STEP_PIN PE9
#define E1_DIR_PIN PE8
#define E1_ENABLE_PIN PC4
#define E2_STEP_PIN PE11
#define E2_DIR_PIN PE10
#define E2_ENABLE_PIN PC5
#define E2_STEP_PIN PE11
#define E2_DIR_PIN PE10
#define E2_ENABLE_PIN PC5
//
// Misc. Functions
//
#define SDSS PA15
#define LED_PIN PB2
#define SDSS PA15
#define LED_PIN PB2
//
// Heaters / Fans
//
#define HEATER_0_PIN PD12 // EXTRUDER 1
//#define HEATER_1_PIN PD13
#define HEATER_0_PIN PD12 // EXTRUDER 1
//#define HEATER_1_PIN PD13
#define HEATER_BED_PIN PB9 // BED
//#define HEATER_BED2_PIN -1 // BED2
//#define HEATER_BED3_PIN -1 // BED3
#define HEATER_BED_PIN PB9 // BED
//#define HEATER_BED2_PIN -1 // BED2
//#define HEATER_BED3_PIN -1 // BED3
#ifndef FAN_PIN
#define FAN_PIN PD14
#define FAN_PIN PD14
#endif
#define FAN1_PIN PD13
#define FAN1_PIN PD13
#define FAN_SOFT_PWM
//
// Temperature Sensors
//
#define TEMP_BED_PIN PA0
#define TEMP_0_PIN PA1
#define TEMP_1_PIN PA2
#define TEMP_2_PIN PA3
#define TEMP_BED_PIN PA0
#define TEMP_0_PIN PA1
#define TEMP_1_PIN PA2
#define TEMP_2_PIN PA3
// Laser control
#if HAS_CUTTER
#define SPINDLE_LASER_PWM_PIN PB8
#define SPINDLE_LASER_ENA_PIN PD5
#define SPINDLE_LASER_PWM_PIN PB8
#define SPINDLE_LASER_ENA_PIN PD5
#endif
//
@ -115,54 +115,54 @@
#if HAS_SPI_LCD
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define LCD_PINS_RS 49 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 51 // SID (MOSI)
#define LCD_PINS_D4 52 // SCK (CLK) clock
#define LCD_PINS_RS 49 // CS chip select /SS chip slave select
#define LCD_PINS_ENABLE 51 // SID (MOSI)
#define LCD_PINS_D4 52 // SCK (CLK) clock
#elif BOTH(NEWPANEL, PANEL_ONE)
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#else
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#define LCD_PINS_RS PB8
#define LCD_PINS_ENABLE PD2
#define LCD_PINS_D4 PB12
#define LCD_PINS_D5 PB13
#define LCD_PINS_D6 PB14
#define LCD_PINS_D7 PB15
#if DISABLED(NEWPANEL)
#define BEEPER_PIN 33
#define BEEPER_PIN 33
// Buttons attached to a shift register
// Not wired yet
//#define SHIFT_CLK 38
//#define SHIFT_LD 42
//#define SHIFT_OUT 40
//#define SHIFT_EN 17
//#define SHIFT_CLK 38
//#define SHIFT_LD 42
//#define SHIFT_OUT 40
//#define SHIFT_EN 17
#endif
#endif
#if ENABLED(TOUCH_BUTTONS)
#define TOUCH_CS_PIN PB12 // SPI2_NSS
#define TOUCH_SCK_PIN PB13
#define TOUCH_MOSI_PIN PB14
#define TOUCH_MISO_PIN PB15
#define TOUCH_INT_PIN PC6 // (PenIRQ coming from ADS7843)
#define TOUCH_CS_PIN PB12 // SPI2_NSS
#define TOUCH_SCK_PIN PB13
#define TOUCH_MOSI_PIN PB14
#define TOUCH_MISO_PIN PB15
#define TOUCH_INT_PIN PC6 // (PenIRQ coming from ADS7843)
#elif ENABLED(NEWPANEL)
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
#define BEEPER_PIN 37
#define BEEPER_PIN 37
#define BTN_EN1 31
#define BTN_EN2 33
#define BTN_ENC 35
#define BTN_EN1 31
#define BTN_EN2 33
#define BTN_ENC 35
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
#define LCD_BACKLIGHT_PIN 39
@ -170,113 +170,113 @@
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SD_DETECT_PIN 42
#elif ENABLED(LCD_I2C_PANELOLU2)
#define BTN_EN1 47
#define BTN_EN2 43
#define BTN_ENC 32
#define LCD_SDSS 53
#define SD_DETECT_PIN -1
#define KILL_PIN 41
#define BTN_EN1 47
#define BTN_EN2 43
#define BTN_ENC 32
#define LCD_SDSS 53
#define SD_DETECT_PIN -1
#define KILL_PIN 41
#elif ENABLED(LCD_I2C_VIKI)
#define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42.
#define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13.
#define BTN_ENC -1
#define LCD_SDSS 53
#define BTN_ENC -1
#define LCD_SDSS 53
#define SD_DETECT_PIN 49
#elif ANY(VIKI2, miniVIKI)
#define BEEPER_PIN 33
#define BEEPER_PIN 33
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 45
#define DOGLCD_A0 44
#define DOGLCD_CS 45
#define LCD_SCREEN_ROT_180
#define BTN_EN1 22
#define BTN_EN2 7
#define BTN_ENC 39
#define BTN_EN1 22
#define BTN_EN2 7
#define BTN_ENC 39
#define SDSS 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define SDSS 53
#define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board
#define KILL_PIN 31
#define KILL_PIN 31
#define STAT_LED_RED_PIN 32
#define STAT_LED_RED_PIN 32
#define STAT_LED_BLUE_PIN 35
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define BTN_EN1 35
#define BTN_EN2 37
#define BTN_ENC 31
#define BTN_EN1 35
#define BTN_EN2 37
#define BTN_ENC 31
#define SD_DETECT_PIN 49
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER_PIN 23
#define DOGLCD_CS 29
#define DOGLCD_A0 27
#define LCD_SDSS 53
#define KILL_PIN 41
#define BEEPER_PIN 23
#define DOGLCD_CS 29
#define DOGLCD_A0 27
#define LCD_BACKLIGHT_PIN 33
#elif ENABLED(MINIPANEL)
#define BEEPER_PIN 42
#define BEEPER_PIN 42
// Pins for DOGM SPI LCD Support
#define DOGLCD_A0 44
#define DOGLCD_CS 66
#define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65
#define SDSS 53
#define DOGLCD_A0 44
#define DOGLCD_CS 66
#define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65
#define SDSS 53
#define KILL_PIN 64
#define KILL_PIN 64
// GLCD features
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
// The encoder and click button
#define BTN_EN1 40
#define BTN_EN2 63
#define BTN_ENC 59
#define BTN_EN1 40
#define BTN_EN2 63
#define BTN_ENC 59
// not connected to a pin
#define SD_DETECT_PIN 49
#else
// Beeper on AUX-4
#define BEEPER_PIN 33
#define BEEPER_PIN 33
// Buttons directly attached to AUX-2
#if ENABLED(REPRAPWORLD_KEYPAD)
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SHIFT_OUT 40
#define SHIFT_CLK 44
#define SHIFT_LD 42
#define BTN_EN1 64
#define BTN_EN2 59
#define BTN_ENC 63
#define SHIFT_OUT 40
#define SHIFT_CLK 44
#define SHIFT_LD 42
#elif ENABLED(PANEL_ONE)
#define BTN_EN1 59 // AUX2 PIN 3
#define BTN_EN2 63 // AUX2 PIN 4
#define BTN_ENC 49 // AUX3 PIN 7
#define BTN_EN1 59 // AUX2 PIN 3
#define BTN_EN2 63 // AUX2 PIN 4
#define BTN_ENC 49 // AUX3 PIN 7
#else
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31
#define BTN_EN1 37
#define BTN_EN2 35
#define BTN_ENC 31
#endif
#if ENABLED(G3D_PANEL)
#define SD_DETECT_PIN 49
#define KILL_PIN 41
#define KILL_PIN 41
#else
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
//#define SD_DETECT_PIN -1 // Ramps doesn't use this
#endif
#endif