bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

update example configurations

Browse Source 
update old comments
update or delete deprecated definitions
complement forgotten updates
adjust spacing
some cosmetic changes
This commit is contained in:
esenapaj2
2016-03-07 22:03:33 +09:00
parent fac85f6fa1
commit 29e09c7c3e
33 changed files with 261 additions and 160 deletions
Download Patch File Download Diff File Expand all files Collapse all files

16
Marlin/example_configurations/TAZ4/Configuration.h
View File

@ -461,10 +461,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// @section bedlevel
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line).
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z probe repeatability test will be included if auto bed leveling is enabled.
//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
//#define DEBUG_LEVELING_FEATURE
#define Z_MIN_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
#if ENABLED(ENABLE_AUTO_BED_LEVELING)
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
// There are 2 different ways to specify probing locations:
//
@ -543,8 +544,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area.
// When defined, it will:
@ -591,7 +593,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//
//#define Z_MIN_PROBE_ENDSTOP
#endif // ENABLE_AUTO_BED_LEVELING
#endif // AUTO_BED_LEVELING_FEATURE
// @section homing
@ -642,7 +644,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// Custom M code points
#define CUSTOM_M_CODES
#if ENABLED(CUSTOM_M_CODES)
#if ENABLED(ENABLE_AUTO_BED_LEVELING)
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
#define Z_PROBE_OFFSET_RANGE_MIN -20
#define Z_PROBE_OFFSET_RANGE_MAX 20

2
Marlin/example_configurations/TAZ4/Configuration_adv.h
View File

@ -52,7 +52,7 @@
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* mintemp and maxtemp. Turn this off by executing M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/