bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

update example configurations

Browse Source 
update old comments
update or delete deprecated definitions
complement forgotten updates
adjust spacing
some cosmetic changes
This commit is contained in:
esenapaj2
2016-03-07 22:03:33 +09:00
parent fac85f6fa1
commit 29e09c7c3e
33 changed files with 261 additions and 160 deletions
Download Patch File Download Diff File Expand all files Collapse all files

7
Marlin/example_configurations/SCARA/Configuration.h
View File

@ -477,7 +477,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#define FRONT_PROBE_BED_POSITION 20
#define BACK_PROBE_BED_POSITION 170
#define MIN_PROBE_EDGE 10 // The Z probe square sides can be no smaller than this.
#define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
// Set the number of grid points per dimension.
// You probably don't need more than 3 (squared=9).
@ -532,8 +532,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
//#define Z_PROBE_SLED // Turn on if you have a Z probe mounted on a sled like those designed by Charles Bell.
//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
// If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
// it is highly recommended you let this Z_SAFE_HOMING enabled!!!
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!
//#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with Z probe outside the bed area.
// When defined, it will:

7
Marlin/example_configurations/SCARA/Configuration_adv.h
View File

@ -52,7 +52,7 @@
* The maximum buffered steps/sec of the extruder motor is called "se".
* Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
* The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
* mintemp and maxtemp. Turn this off by excuting M109 without F*
* mintemp and maxtemp. Turn this off by executing M109 without F*
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
*/
@ -347,7 +347,6 @@
//#define USE_SMALL_INFOFONT
#endif // DOGLCD
// @section more
// The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
@ -368,6 +367,7 @@
//#define BABYSTEPPING
#if ENABLED(BABYSTEPPING)
#define BABYSTEP_XY //not only z, but also XY in the menu. more clutter, more functions
//not implemented for CoreXY and deltabots!
#define BABYSTEP_INVERT_Z false //true for inverse movements in Z
#define BABYSTEP_MULTIPLICATOR 1 //faster movements
#endif
@ -459,6 +459,9 @@ const unsigned int dropsegments = 5; //everything with less than this number of
#define FILAMENTCHANGE_ZADD 10
#define FILAMENTCHANGE_FIRSTRETRACT -2
#define FILAMENTCHANGE_FINALRETRACT -100
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
#endif
#endif