diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index f02e69ee5a..175a5fbef3 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -2164,7 +2164,6 @@ //#define PCA9632 // Support for PCA9533 PWM LED driver -// https://github.com/mikeshub/SailfishRGB_LED //#define PCA9533 /** diff --git a/Marlin/src/feature/leds/leds.cpp b/Marlin/src/feature/leds/leds.cpp index 995693ffc5..13d60fd5b7 100644 --- a/Marlin/src/feature/leds/leds.cpp +++ b/Marlin/src/feature/leds/leds.cpp @@ -39,7 +39,7 @@ #endif #if ENABLED(PCA9533) - #include + #include "pca9533.h" #endif #if ENABLED(LED_COLOR_PRESETS) @@ -72,7 +72,7 @@ void LEDLights::setup() { neo.init(); #endif #if ENABLED(PCA9533) - RGBinit(); + PCA9533_init(); #endif #if ENABLED(LED_USER_PRESET_STARTUP) set_default(); @@ -141,7 +141,7 @@ void LEDLights::set_color(const LEDColor &incol #endif #if ENABLED(PCA9533) - RGBsetColor(incol.r, incol.g, incol.b, true); + PCA9533_setColor(incol.r, incol.g, incol.b); #endif #if EITHER(LED_CONTROL_MENU, PRINTER_EVENT_LEDS) diff --git a/Marlin/src/feature/leds/pca9533.cpp b/Marlin/src/feature/leds/pca9533.cpp new file mode 100644 index 0000000000..82bdaf6665 --- /dev/null +++ b/Marlin/src/feature/leds/pca9533.cpp @@ -0,0 +1,127 @@ +/* + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * PCA9533 LED controller driver (MightyBoard, FlashForge Creator Pro, etc.) + * by @grauerfuchs - 1 Apr 2020 + */ +#include "../../inc/MarlinConfig.h" + +#if ENABLED(PCA9533) + +#include "pca9533.h" +#include + +void PCA9533_init() { + Wire.begin(); + PCA9533_reset(); +} + +static void PCA9533_writeAllRegisters(uint8_t psc0, uint8_t pwm0, uint8_t psc1, uint8_t pwm1, uint8_t ls0){ + uint8_t data[6] = { PCA9533_REG_PSC0 | PCA9533_REGM_AI, psc0, pwm0, psc1, pwm1, ls0 }; + Wire.beginTransmission(PCA9533_Addr >> 1); + Wire.write(data, 6); + Wire.endTransmission(); + delayMicroseconds(1); +} + +static void PCA9533_writeRegister(uint8_t reg, uint8_t val){ + uint8_t data[2] = { reg, val }; + Wire.beginTransmission(PCA9533_Addr >> 1); + Wire.write(data, 2); + Wire.endTransmission(); + delayMicroseconds(1); +} + +// Reset (clear) all registers +void PCA9533_reset() { + PCA9533_writeAllRegisters(0, 0, 0, 0, 0); +} + +// Turn all LEDs off +void PCA9533_setOff() { + PCA9533_writeRegister(PCA9533_REG_SEL, 0); +} + +void PCA9533_setColor(uint8_t red, uint8_t green, uint8_t blue) { + uint8_t r_pwm0 = 0; // Register data - PWM value + uint8_t r_pwm1 = 0; // Register data - PWM value + + uint8_t op_g = 0, op_r = 0, op_b = 0; // Opcodes - Green, Red, Blue + + // Light theory! GREEN takes priority because + // it's the most visible to the human eye. + if (green == 0) op_g = PCA9533_LED_OP_OFF; + else if (green == 255) op_g = PCA9533_LED_OP_ON; + else { r_pwm0 = green; op_g = PCA9533_LED_OP_PWM0; } + + // RED + if (red == 0) op_r = PCA9533_LED_OP_OFF; + else if (red == 255) op_r = PCA9533_LED_OP_ON; + else if (r_pwm0 == 0 || r_pwm0 == red) { + r_pwm0 = red; op_r = PCA9533_LED_OP_PWM0; + } + else { + r_pwm1 = red; op_r = PCA9533_LED_OP_PWM1; + } + + // BLUE + if (blue == 0) op_b = PCA9533_LED_OP_OFF; + else if (blue == 255) op_b = PCA9533_LED_OP_ON; + else if (r_pwm0 == 0 || r_pwm0 == blue) { + r_pwm0 = blue; op_b = PCA9533_LED_OP_PWM0; + } + else if (r_pwm1 == 0 || r_pwm1 == blue) { + r_pwm1 = blue; op_b = PCA9533_LED_OP_PWM1; + } + else { + /** + * Conflict. 3 values are requested but only 2 channels exist. + * G is on channel 0 and R is on channel 1, so work from there. + * Find the closest match, average the values, then use the free channel. + */ + uint8_t dgb = ABS(green - blue), + dgr = ABS(green - red), + dbr = ABS(blue - red); + if (dgb < dgr && dgb < dbr) { // Mix with G on channel 0. + op_b = PCA9533_LED_OP_PWM0; + r_pwm0 = uint8_t(((uint16_t)green + (uint16_t)blue) / 2); + } + else if (dbr <= dgr && dbr <= dgb) { // Mix with R on channel 1. + op_b = PCA9533_LED_OP_PWM1; + r_pwm1 = uint8_t(((uint16_t)red + (uint16_t)blue) / 2); + } + else { // Mix R+G on 0 and put B on 1. + op_r = PCA9533_LED_OP_PWM0; + r_pwm0 = uint8_t(((uint16_t)green + (uint16_t)red) / 2); + op_b = PCA9533_LED_OP_PWM1; + r_pwm1 = blue; + } + } + + // Write the changes to the hardware + PCA9533_writeAllRegisters(0, r_pwm0, 0, r_pwm1, + (op_g << PCA9533_LED_OFS_GRN) | (op_r << PCA9533_LED_OFS_RED) | (op_b << PCA9533_LED_OFS_BLU) + ); +} + +#endif // PCA9533 diff --git a/Marlin/src/feature/leds/pca9533.h b/Marlin/src/feature/leds/pca9533.h new file mode 100644 index 0000000000..a134ca15fd --- /dev/null +++ b/Marlin/src/feature/leds/pca9533.h @@ -0,0 +1,59 @@ +/* + * Marlin 3D Printer Firmware + * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/* + * Driver for the PCA9533 LED controller found on the MightyBoard + * used by FlashForge Creator Pro, MakerBot, etc. + * Written 2020 APR 01 by grauerfuchs + */ +#include + +#define ENABLE_I2C_PULLUPS + +// Chip address (for Wire) +#define PCA9533_Addr 0xC4 + +// Control registers +#define PCA9533_REG_READ 0x00 +#define PCA9533_REG_PSC0 0x01 +#define PCA9533_REG_PWM0 0x02 +#define PCA9533_REG_PSC1 0x03 +#define PCA9533_REG_PWM1 0x04 +#define PCA9533_REG_SEL 0x05 +#define PCA9533_REGM_AI 0x10 + +// LED selector operation +#define PCA9533_LED_OP_OFF 0B00 +#define PCA9533_LED_OP_ON 0B01 +#define PCA9533_LED_OP_PWM0 0B10 +#define PCA9533_LED_OP_PWM1 0B11 + +// Select register bit offsets for LED colors +#define PCA9533_LED_OFS_RED 0 +#define PCA9533_LED_OFS_GRN 2 +#define PCA9533_LED_OFS_BLU 4 + +void PCA9533_init(); +void PCA9533_reset(); +void PCA9533_setColor(uint8_t red, uint8_t green, uint8_t blue); +void PCA9533_setOff(); diff --git a/buildroot/share/PlatformIO/variants/BIGTREE_SKR_PRO_1v1/variant.h b/buildroot/share/PlatformIO/variants/BIGTREE_SKR_PRO_1v1/variant.h index 5ff2ea5768..0eab1abe53 100644 --- a/buildroot/share/PlatformIO/variants/BIGTREE_SKR_PRO_1v1/variant.h +++ b/buildroot/share/PlatformIO/variants/BIGTREE_SKR_PRO_1v1/variant.h @@ -234,7 +234,7 @@ extern "C" { // On-board LED pin number #define LED_BUILTIN PA7 -//#define LED_GREEN LED_BUILTIN should be defined here but omitted to avoid redefinition in SailfishRGB_LED +#define LED_GREEN LED_BUILTIN // Below SPI and I2C definitions already done in the core // Could be redefined here if differs from the default one diff --git a/buildroot/share/tests/DUE-tests b/buildroot/share/tests/DUE-tests index cfce93a92e..0d9b95e1cf 100755 --- a/buildroot/share/tests/DUE-tests +++ b/buildroot/share/tests/DUE-tests @@ -16,7 +16,7 @@ opt_set FANMUX0_PIN 53 opt_enable S_CURVE_ACCELERATION EEPROM_SETTINGS GCODE_MACROS \ PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING CODEPENDENT_XY_HOMING \ EEPROM_SETTINGS SDSUPPORT BINARY_FILE_TRANSFER \ - BLINKM PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \ + BLINKM PCA9533 PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \ NEOPIXEL_LED CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CASE_LIGHT_MENU \ NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE FILAMENT_RUNOUT_DISTANCE_MM FILAMENT_RUNOUT_SENSOR \ AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \ diff --git a/buildroot/share/tests/rambo-tests b/buildroot/share/tests/rambo-tests index 57c363c3a4..7fab4fc6ca 100644 --- a/buildroot/share/tests/rambo-tests +++ b/buildroot/share/tests/rambo-tests @@ -53,7 +53,7 @@ opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TE FIX_MOUNTED_PROBE Z_SAFE_HOMING CODEPENDENT_XY_HOMING PIDTEMPBED PROBE_TEMP_COMPENSATION \ PROBING_HEATERS_OFF PROBING_FANS_OFF PROBING_STEPPERS_OFF WAIT_FOR_BED_HEATER \ EEPROM_SETTINGS SDSUPPORT SD_REPRINT_LAST_SELECTED_FILE BINARY_FILE_TRANSFER \ - BLINKM PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \ + BLINKM PCA9533 PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \ NEOPIXEL_LED CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CASE_LIGHT_MENU \ PID_PARAMS_PER_HOTEND PID_AUTOTUNE_MENU PID_EDIT_MENU LCD_SHOW_E_TOTAL \ PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 LEVEL_BED_CORNERS \ diff --git a/platformio.ini b/platformio.ini index f7fb31ec2e..2ba1c5c1f3 100644 --- a/platformio.ini +++ b/platformio.ini @@ -33,7 +33,6 @@ lib_deps = LiquidTWI2=https://github.com/lincomatic/LiquidTWI2/archive/master.zip Arduino-L6470=https://github.com/ameyer/Arduino-L6470/archive/0.8.0.zip SailfishLCD=https://github.com/mikeshub/SailfishLCD/archive/master.zip - SailfishRGB_LED=https://github.com/mikeshub/SailfishRGB_LED/archive/master.zip SlowSoftI2CMaster=https://github.com/mikeshub/SlowSoftI2CMaster/archive/master.zip # Globally defined properties @@ -623,7 +622,7 @@ build_flags = ${common.build_flags} build_unflags = -std=gnu++11 extra_scripts = pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py buildroot/share/PlatformIO/scripts/STEVAL__F401XX.py -lib_ignore = Adafruit NeoPixel, TMCStepper, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster, SoftwareSerial +lib_ignore = Adafruit NeoPixel, TMCStepper, SailfishLCD, SlowSoftI2CMaster, SoftwareSerial src_filter = ${common.default_src_filter} + # @@ -639,7 +638,7 @@ build_flags = ${common.build_flags} -IMarlin/src/HAL/STM32 build_unflags = -std=gnu++11 extra_scripts = pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py -lib_ignore = Adafruit NeoPixel, TMCStepper, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster, SoftwareSerial +lib_ignore = Adafruit NeoPixel, TMCStepper, SailfishLCD, SlowSoftI2CMaster, SoftwareSerial src_filter = ${common.default_src_filter} + @@ -679,7 +678,7 @@ build_flags = ${common.build_flags} -IMarlin/src/HAL/STM32 build_unflags = -std=gnu++11 extra_scripts = pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py -lib_ignore = Adafruit NeoPixel, TMCStepper, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster, SoftwareSerial +lib_ignore = Adafruit NeoPixel, TMCStepper, SailfishLCD, SlowSoftI2CMaster, SoftwareSerial src_filter = ${common.default_src_filter} + # @@ -742,7 +741,7 @@ build_flags = ${common.build_flags} -DPIN_SERIAL2_TX=PD_5 build_unflags = -std=gnu++11 extra_scripts = pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py -lib_ignore = Adafruit NeoPixel, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster +lib_ignore = Adafruit NeoPixel, SailfishLCD, SlowSoftI2CMaster src_filter = ${common.default_src_filter} + # @@ -780,7 +779,7 @@ lib_deps = ${common.lib_deps} ESP3DLib=https://github.com/luc-github/ESP3DLib.git arduinoWebSockets=https://github.com/Links2004/arduinoWebSockets.git ESP32SSDP=https://github.com/luc-github/ESP32SSDP.git -lib_ignore = LiquidCrystal, LiquidTWI2, SailfishLCD, SailfishRGB_LED, ESPAsyncTCP +lib_ignore = LiquidCrystal, LiquidTWI2, SailfishLCD, ESPAsyncTCP src_filter = ${common.default_src_filter} + upload_speed = 115200 #upload_port = marlinesp.local