Added a light-weight status screen for the ST7920
- The status screen uses the ST7920 character generator to greatly reduce SPI traffic and MCU load when updating the status screen. - Has been tested with the RepRapDiscount Full Graphics Smart Controller but should work with any LCD that uses an ST7920 or fully compatible controller.
This commit is contained in:
Marcio Teixeira
committed by
Scott Lahteine
Scott Lahteine
parent
a6563df705
commit
24eb275b99
@@ -1513,7 +1513,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1513,7 +1513,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1513,7 +1513,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1661,9 +1661,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// Note: Details on connecting to the Anet V1.0 controller are in the file pins_ANET_10.h
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1516,6 +1516,7 @@
|
||||
//
|
||||
//#define G3D_PANEL
|
||||
|
||||
|
||||
//
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
@@ -1524,6 +1525,18 @@
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
// controller and SD support - http://reprap.org/wiki/Mini_panel
|
||||
|
||||
@@ -1513,7 +1513,18 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1513,7 +1513,18 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1519,7 +1519,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1517,7 +1517,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1524,7 +1524,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1515,6 +1515,18 @@
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
// controller and SD support - http://reprap.org/wiki/Mini_panel
|
||||
|
||||
@@ -1516,7 +1516,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1544,7 +1544,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1498,7 +1498,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1513,7 +1513,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1546,7 +1546,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1513,7 +1513,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1507,7 +1507,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1637,7 +1637,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1527,7 +1527,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
@@ -1516,7 +1516,18 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
// If USE_ST7920_LIGHTWEIGHT_UI is uncommented, then an alternative
|
||||
// light-weight status screen will be used that takes advantage of
|
||||
// the ST7920 character-generator to conserve MCU resources.
|
||||
//
|
||||
// Since the lightweight status screen can only show a status
|
||||
// message or the position, but not both, set DELAY_TO_SHOW_POSITION
|
||||
// to the number of seconds until the position is revealed after a new
|
||||
// status message is drawn.
|
||||
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
//#define USE_ST7920_LIGHTWEIGHT_UI
|
||||
//#define DELAY_TO_SHOW_POSITION 20
|
||||
|
||||
//
|
||||
// MakerLab Mini Panel with graphic
|
||||
|
||||
247
Marlin/src/lcd/dogm/ultralcd_impl_st7920_lite_status_screen.h
Normal file
247
Marlin/src/lcd/dogm/ultralcd_impl_st7920_lite_status_screen.h
Normal file
@@ -0,0 +1,247 @@
|
||||
/*
|
||||
* Lightweight Status Screen for the RepRapDiscount Full
|
||||
* Graphics Smart Controller (ST7920-based 128x64 LCD)
|
||||
*
|
||||
* (c) 2017 Aleph Objects, Inc.
|
||||
*
|
||||
* The code in this page is free software: you can
|
||||
* redistribute it and/or modify it under the terms of the GNU
|
||||
* General Public License (GNU GPL) as published by the Free Software
|
||||
* Foundation, either version 3 of the License, or (at your option)
|
||||
* any later version. The code is distributed WITHOUT ANY WARRANTY;
|
||||
* without even the implied warranty of MERCHANTABILITY or FITNESS
|
||||
* FOR A PARTICULAR PURPOSE. See the GNU GPL for more details.
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef ULTRALCD_ST7920_LITE_STATUS_H
|
||||
#define ULTRALCD_ST7920_LITE_STATUS_H
|
||||
|
||||
class ST7920_Lite_Status_Screen {
|
||||
private:
|
||||
static struct st7920_state_t {
|
||||
uint8_t synced : 1; // Whether a sync has been sent
|
||||
uint8_t cmd : 1; // Whether the sync was cmd or data
|
||||
uint8_t extended : 1;
|
||||
uint8_t graphics : 1;
|
||||
uint8_t sa : 1;
|
||||
} current_bits;
|
||||
|
||||
static void cs();
|
||||
static void ncs();
|
||||
static void sync_cmd();
|
||||
static void sync_dat();
|
||||
static void write_byte(uint8_t w);
|
||||
|
||||
static void cmd(uint8_t cmd);
|
||||
static void begin_data();
|
||||
static void write_word(uint16_t w);
|
||||
static void write_str(const char *str);
|
||||
static void write_str(const char *str, uint8_t len);
|
||||
static void write_str_P(const char *str);
|
||||
static void write_str(progmem_str str);
|
||||
static void write_number(uint8_t value, uint8_t digits=3);
|
||||
|
||||
static void _extended_function_set(bool extended, bool graphics);
|
||||
static void _scroll_or_addr_select(bool sa);
|
||||
static void reset_state_from_unknown();
|
||||
|
||||
static void home();
|
||||
static void display_status(bool display_on, bool cursor_on, bool blink_on);
|
||||
static void extended_function_set(bool extended);
|
||||
static void graphics(bool graphics);
|
||||
static void entry_mode_select(bool ac_increase, bool shift);
|
||||
static void scroll_or_addr_select(bool sa);
|
||||
static void set_ddram_address(uint8_t addr);
|
||||
static void set_cgram_address(uint8_t addr);
|
||||
static void set_gdram_address(uint8_t x, uint8_t y);
|
||||
|
||||
static void clear();
|
||||
static void clear_ddram();
|
||||
static void clear_gdram();
|
||||
|
||||
static void load_cgram_icon(uint16_t addr, const void *data);
|
||||
static void draw_gdram_icon(uint8_t x, uint8_t y, const void *data);
|
||||
|
||||
static uint8_t string_checksum(const char *str);
|
||||
|
||||
protected:
|
||||
static void draw_static_elements();
|
||||
static void draw_progress_bar(uint8_t value);
|
||||
static void draw_fan_icon(bool whichIcon);
|
||||
static void draw_heat_icon(bool whichIcon, bool heating);
|
||||
static void draw_extruder_1_temp(uint8_t temp, uint8_t target);
|
||||
static void draw_extruder_2_temp(uint8_t temp, uint8_t target);
|
||||
static void draw_bed_temp(uint8_t temp, uint8_t target);
|
||||
static void draw_fan_speed(uint8_t value);
|
||||
static void draw_print_time(uint32_t elapsed);
|
||||
static void draw_feedrate_percentage(uint8_t percentage);
|
||||
static void draw_status_message(const char *str);
|
||||
static void draw_position(const float x, const float y, const float z, bool position_known = true);
|
||||
|
||||
static bool indicators_changed();
|
||||
static bool position_changed();
|
||||
static bool blink_changed();
|
||||
static bool status_changed();
|
||||
|
||||
static void update_indicators(bool forceUpdate);
|
||||
static void update_position(bool forceUpdate, bool resetChecksum);
|
||||
static void update_status_or_position(bool forceUpdate);
|
||||
static void update_progress(bool forceUpdate);
|
||||
|
||||
public:
|
||||
static void update(bool forceUpdate);
|
||||
static void on_entry();
|
||||
static void on_exit();
|
||||
static void clear_text_buffer();
|
||||
};
|
||||
|
||||
/************************** ICON DEFINITIONS *************************************/
|
||||
|
||||
#define CGRAM_ICON_1_ADDR 0x00
|
||||
#define CGRAM_ICON_2_ADDR 0x10
|
||||
#define CGRAM_ICON_3_ADDR 0x20
|
||||
#define CGRAM_ICON_4_ADDR 0x30
|
||||
|
||||
#define CGRAM_ICON_1_WORD 0x00
|
||||
#define CGRAM_ICON_2_WORD 0x02
|
||||
#define CGRAM_ICON_3_WORD 0x04
|
||||
#define CGRAM_ICON_4_WORD 0x06
|
||||
|
||||
PROGMEM const uint16_t nozzle_icon[] = {
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000111111110000,
|
||||
0b0001111111111000,
|
||||
0b0001111111111000,
|
||||
0b0001111111111000,
|
||||
0b0000111111110000,
|
||||
0b0000111111110000,
|
||||
0b0001111111111000,
|
||||
0b0001111111111000,
|
||||
0b0001111111111000,
|
||||
0b0000011111100000,
|
||||
0b0000001111000000,
|
||||
0b0000000110000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000
|
||||
};
|
||||
|
||||
PROGMEM const uint16_t bed_icon[] = {
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0111111111111110,
|
||||
0b0111111111111110,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000
|
||||
};
|
||||
|
||||
PROGMEM const uint16_t heat1_icon[] = {
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0010001000100000,
|
||||
0b0001000100010000,
|
||||
0b0000100010001000,
|
||||
0b0000100010001000,
|
||||
0b0001000100010000,
|
||||
0b0010001000100000,
|
||||
0b0010001000100000,
|
||||
0b0001000100010000,
|
||||
0b0000100010001000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000
|
||||
};
|
||||
|
||||
PROGMEM const uint16_t heat2_icon[] = {
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000100010001000,
|
||||
0b0000100010001000,
|
||||
0b0001000100010000,
|
||||
0b0010001000100000,
|
||||
0b0010001000100000,
|
||||
0b0001000100010000,
|
||||
0b0000100010001000,
|
||||
0b0000100010001000,
|
||||
0b0001000100010000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000
|
||||
};
|
||||
|
||||
PROGMEM const uint16_t fan1_icon[] = {
|
||||
0b0000000000000000,
|
||||
0b0111111111111110,
|
||||
0b0111000000001110,
|
||||
0b0110001111000110,
|
||||
0b0100001111000010,
|
||||
0b0100000110000010,
|
||||
0b0101100000011010,
|
||||
0b0101110110111010,
|
||||
0b0101100000011010,
|
||||
0b0100000110000010,
|
||||
0b0100001111000010,
|
||||
0b0110001111000110,
|
||||
0b0111000000001110,
|
||||
0b0111111111111110,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000
|
||||
};
|
||||
|
||||
PROGMEM const uint16_t fan2_icon[] = {
|
||||
0b0000000000000000,
|
||||
0b0111111111111110,
|
||||
0b0111000000001110,
|
||||
0b0110010000100110,
|
||||
0b0100111001110010,
|
||||
0b0101111001111010,
|
||||
0b0100110000110010,
|
||||
0b0100000110000010,
|
||||
0b0100110000110010,
|
||||
0b0101111001111010,
|
||||
0b0100111001110010,
|
||||
0b0110010000100110,
|
||||
0b0111000000001110,
|
||||
0b0111111111111110,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000
|
||||
};
|
||||
|
||||
PROGMEM const uint16_t feedrate_icon[] = {
|
||||
0b0000000000000000,
|
||||
0b0111111000000000,
|
||||
0b0100000000000000,
|
||||
0b0100000000000000,
|
||||
0b0100000000000000,
|
||||
0b0111111011111000,
|
||||
0b0100000010000100,
|
||||
0b0100000010000100,
|
||||
0b0100000010000100,
|
||||
0b0100000011111000,
|
||||
0b0000000010001000,
|
||||
0b0000000010000100,
|
||||
0b0000000010000100,
|
||||
0b0000000010000010,
|
||||
0b0000000000000000,
|
||||
0b0000000000000000
|
||||
};
|
||||
|
||||
static void lcd_implementation_status_screen();
|
||||
static void lcd_in_status(bool inStatus);
|
||||
|
||||
#endif // ULTRALCD_ST7920_LITE_STATUS_H
|
||||
@@ -0,0 +1,757 @@
|
||||
/*
|
||||
* Lightweight Status Screen for the RepRapDiscount Full
|
||||
* Graphics Smart Controller (ST7920-based 128x64 LCD)
|
||||
*
|
||||
* (c) 2017 Aleph Objects, Inc.
|
||||
*
|
||||
* The code in this page is free software: you can
|
||||
* redistribute it and/or modify it under the terms of the GNU
|
||||
* General Public License (GNU GPL) as published by the Free Software
|
||||
* Foundation, either version 3 of the License, or (at your option)
|
||||
* any later version. The code is distributed WITHOUT ANY WARRANTY;
|
||||
* without even the implied warranty of MERCHANTABILITY or FITNESS
|
||||
* FOR A PARTICULAR PURPOSE. See the GNU GPL for more details.
|
||||
*
|
||||
*/
|
||||
|
||||
/* This is an implementation of a status screen for the RepRapDiscount
|
||||
* Full Graphics Smart Controller using native ST7920 commands rather
|
||||
* than using U8Glib.
|
||||
*
|
||||
* This alternative status screen makes use of the built-in character
|
||||
* generation capabilities of the ST7920 to update the status screen
|
||||
* with less SPI traffic and CPU use. In particular:
|
||||
*
|
||||
* - The fan and bed animations are handled using custom characters
|
||||
* that are stored in CGRAM. This allows for the animation to be
|
||||
* updated by writing a single character to the text-buffer (DDRAM).
|
||||
*
|
||||
* - All the information in the status screen is text that is written
|
||||
* to DDRAM, so the work of generating the bitmaps is offloaded to
|
||||
* the ST7920 rather than being render by U8Glib on the MCU.
|
||||
*
|
||||
* - The graphics buffer (GDRAM) is only used for static graphics
|
||||
* elements (nozzle and feedrate bitmaps) and for the progress
|
||||
* bar, so updates are sporadic.
|
||||
*/
|
||||
|
||||
#include "../../libs/duration_t.h"
|
||||
|
||||
typedef const __FlashStringHelper *progmem_str;
|
||||
|
||||
#include "ultralcd_impl_st7920_lite_status_screen.h"
|
||||
|
||||
#define BUFFER_WIDTH 256
|
||||
#define BUFFER_HEIGHT 32
|
||||
|
||||
#define DDRAM_LINE_1 0x00
|
||||
#define DDRAM_LINE_2 0x10
|
||||
#define DDRAM_LINE_3 0x08
|
||||
#define DDRAM_LINE_4 0x18
|
||||
|
||||
ST7920_Lite_Status_Screen::st7920_state_t ST7920_Lite_Status_Screen::current_bits;
|
||||
|
||||
void ST7920_Lite_Status_Screen::cmd(uint8_t cmd) {
|
||||
if(!current_bits.synced || !current_bits.cmd) {
|
||||
current_bits.synced = true;
|
||||
current_bits.cmd = true;
|
||||
sync_cmd();
|
||||
}
|
||||
write_byte(cmd);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::begin_data() {
|
||||
extended_function_set(false);
|
||||
if(!current_bits.synced || current_bits.cmd) {
|
||||
current_bits.synced = true;
|
||||
current_bits.cmd = false;
|
||||
sync_dat();
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::write_word(uint16_t w) {
|
||||
write_byte((w >> 8) & 0xFF);
|
||||
write_byte((w >> 0) & 0xFF);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::write_str(const char *str) {
|
||||
while(*str) {
|
||||
write_byte(*str++);
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::write_str(const char *str, uint8_t len) {
|
||||
while(*str && len--) {
|
||||
write_byte(*str++);
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::write_str_P(const char *str) {
|
||||
const char *p_str = (const char *)str;
|
||||
char c = pgm_read_byte_near(p_str++);
|
||||
while(c) {
|
||||
write_byte(c);
|
||||
c = pgm_read_byte_near(p_str++);
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::write_str(progmem_str str) {
|
||||
write_str_P((const char*)str);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::write_number(uint8_t value, uint8_t digits) {
|
||||
char str[7];
|
||||
const char *fmt;
|
||||
switch(digits) {
|
||||
case 6: fmt = PSTR("%6d"); break;
|
||||
case 5: fmt = PSTR("%5d"); break;
|
||||
case 4: fmt = PSTR("%4d"); break;
|
||||
case 3: fmt = PSTR("%3d"); break;
|
||||
case 2: fmt = PSTR("%2d"); break;
|
||||
case 1: fmt = PSTR("%1d"); break;
|
||||
}
|
||||
sprintf_P(str,fmt,value);
|
||||
write_str(str);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::display_status(bool display_on, bool cursor_on, bool blink_on) {
|
||||
extended_function_set(false);
|
||||
cmd(0b00001000 |
|
||||
(display_on ? 0b0100 : 0) |
|
||||
(cursor_on ? 0b0010 : 0) |
|
||||
(blink_on ? 0b0001 : 0)
|
||||
);
|
||||
}
|
||||
|
||||
// Sets the extended and graphics bits simultaneously, regardless of
|
||||
// the current state. This is a helper function for extended_function_set()
|
||||
// and graphics()
|
||||
void ST7920_Lite_Status_Screen::_extended_function_set(bool extended, bool graphics) {
|
||||
cmd( 0b00100000 |
|
||||
(extended ? 0b00000100 : 0) |
|
||||
(graphics ? 0b00000010 : 0)
|
||||
);
|
||||
current_bits.extended = extended;
|
||||
current_bits.graphics = graphics;
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::extended_function_set(bool extended) {
|
||||
if(extended != current_bits.extended) {
|
||||
_extended_function_set(extended, current_bits.graphics);
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::graphics(bool graphics) {
|
||||
if(graphics != current_bits.graphics) {
|
||||
_extended_function_set(current_bits.extended, graphics);
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::entry_mode_select(bool ac_increase, bool shift) {
|
||||
extended_function_set(false);
|
||||
cmd(0b00000100 |
|
||||
(ac_increase ? 0b00000010 : 0) |
|
||||
(shift ? 0b00000001 : 0)
|
||||
);
|
||||
}
|
||||
|
||||
// Sets the sa bit regardless of the current state. This is a helper
|
||||
// function for scroll_or_addr_select()
|
||||
void ST7920_Lite_Status_Screen::_scroll_or_addr_select(bool sa) {
|
||||
extended_function_set(true);
|
||||
cmd(0b00100010 |
|
||||
(sa ? 0b000001 : 0)
|
||||
);
|
||||
current_bits.sa = sa;
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::scroll_or_addr_select(bool sa) {
|
||||
if(sa != current_bits.sa) {
|
||||
_scroll_or_addr_select(sa);
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::set_ddram_address(uint8_t addr) {
|
||||
extended_function_set(false);
|
||||
cmd(0b10000000 | (addr & 0b00111111));
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::set_cgram_address(uint8_t addr) {
|
||||
extended_function_set(false);
|
||||
cmd(0b01000000 | (addr & 0b00111111));
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::set_gdram_address(uint8_t x, uint8_t y) {
|
||||
extended_function_set(true);
|
||||
cmd(0b10000000 | (y & 0b01111111));
|
||||
cmd(0b10000000 | (x & 0b00001111));
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::clear() {
|
||||
extended_function_set(false);
|
||||
cmd(0x00000001);
|
||||
delay(15); //delay for CGRAM clear
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::home() {
|
||||
extended_function_set(false);
|
||||
cmd(0x00000010);
|
||||
}
|
||||
|
||||
/* This fills the entire text buffer with spaces */
|
||||
void ST7920_Lite_Status_Screen::clear_ddram()
|
||||
{
|
||||
set_ddram_address(DDRAM_LINE_1);
|
||||
begin_data();
|
||||
for(int i=0; i < 64;i++) {
|
||||
write_byte(' ');
|
||||
}
|
||||
}
|
||||
|
||||
/* This fills the entire graphics buffer with zeros */
|
||||
void ST7920_Lite_Status_Screen::clear_gdram()
|
||||
{
|
||||
for(int y = 0; y < BUFFER_HEIGHT; y++) {
|
||||
set_gdram_address(0,y);
|
||||
begin_data();
|
||||
for(int i = 0; i < (BUFFER_WIDTH / 16); i++) {
|
||||
write_byte(0);
|
||||
write_byte(0);
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::load_cgram_icon(uint16_t addr, const void *data) {
|
||||
const uint16_t *p_word = (const uint16_t *)data;
|
||||
set_cgram_address(addr);
|
||||
begin_data();
|
||||
for(int i = 0; i < 16; i++) {
|
||||
uint16_t word = pgm_read_word_near(p_word++);
|
||||
write_byte((word & 0xFF00) >> 8);
|
||||
write_byte((word & 0x00FF) >> 0);
|
||||
}
|
||||
}
|
||||
|
||||
/* Draws an icon in GDRAM. The position is specified in
|
||||
as if they were DDRAM coordinates, i.e. the x position
|
||||
is [1-8], while the y position is [1-4] */
|
||||
void ST7920_Lite_Status_Screen::draw_gdram_icon(uint8_t x, uint8_t y, const void *data) {
|
||||
const uint16_t *p_word = (const uint16_t *)data;
|
||||
if(y > 2) {
|
||||
// Handle display folding
|
||||
y -= 2;
|
||||
x += 8;
|
||||
}
|
||||
x -= 1;
|
||||
y -= 1;
|
||||
for(int i = 0; i < 16; i++) {
|
||||
uint16_t word = pgm_read_word_near(p_word++);
|
||||
set_gdram_address(x,i+y*16);
|
||||
begin_data();
|
||||
write_byte((word & 0xFF00) >> 8);
|
||||
write_byte((word & 0x00FF) >> 0);
|
||||
}
|
||||
}
|
||||
|
||||
/************************** MAIN SCREEN *************************************/
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_static_elements() {
|
||||
scroll_or_addr_select(0);
|
||||
|
||||
// Load the animated bed and fan icons
|
||||
load_cgram_icon(CGRAM_ICON_1_ADDR, heat1_icon);
|
||||
load_cgram_icon(CGRAM_ICON_2_ADDR, heat2_icon);
|
||||
load_cgram_icon(CGRAM_ICON_3_ADDR, fan1_icon);
|
||||
load_cgram_icon(CGRAM_ICON_4_ADDR, fan2_icon);
|
||||
|
||||
// Draw the static icons in GDRAM
|
||||
draw_gdram_icon(1,1,nozzle_icon);
|
||||
#if EXTRUDERS == 2
|
||||
draw_gdram_icon(1,2,nozzle_icon);
|
||||
#endif
|
||||
draw_gdram_icon(6,2,feedrate_icon);
|
||||
draw_gdram_icon(1,2,bed_icon);
|
||||
|
||||
// Draw the initial fan icon
|
||||
draw_fan_icon(false);
|
||||
}
|
||||
|
||||
/* Although this is undocumented, the ST7920 allows the character
|
||||
* data buffer (DDRAM) to be used in conjunction with the graphics
|
||||
* bitmap buffer (CGRAM). The contents of the graphics buffer is
|
||||
* XORed with the data from the character generator. This allows
|
||||
* us to make the progess bar out of graphical data (the bar) and
|
||||
* text data (the percentage).
|
||||
*/
|
||||
void ST7920_Lite_Status_Screen::draw_progress_bar(uint8_t value) {
|
||||
#if EXTRUDERS == 1
|
||||
// If we have only one extruder, draw a long progress bar on the third line
|
||||
const int top = 1; // Top in pixels
|
||||
const int bottom = 13; // Bottom in pixels
|
||||
const int left = 8; // Left edge, in 16-bit words
|
||||
const int width = 5; // Width of progress bar, in 16-bit words
|
||||
#else
|
||||
const int top = 16 + 1; // Top in pixels
|
||||
const int bottom = 16 + 13; // Bottom in pixels
|
||||
const int left = 5; // Left edge, in 16-bit words
|
||||
const int width = 3; // Width of progress bar, in 16-bit words
|
||||
#endif
|
||||
const int char_pcnt = 100/width; // How many percent does each 16-bit word represent?
|
||||
|
||||
// Draw the progress bar as a bitmap in CGRAM
|
||||
|
||||
for(int y = top; y <= bottom; y++) {
|
||||
set_gdram_address(left,y);
|
||||
begin_data();
|
||||
for(int x = 0; x < width; x++) {
|
||||
uint16_t gfx_word = 0x0000;
|
||||
if((x+1)*char_pcnt <= value) {
|
||||
// Draw completely filled bytes
|
||||
gfx_word = 0xFFFF;
|
||||
} else if((x*char_pcnt) < value) {
|
||||
// Draw partially filled bytes
|
||||
gfx_word = int(0x8000) >> (value % char_pcnt)*16/char_pcnt;
|
||||
}
|
||||
// Draw the frame around the progress bar
|
||||
if(y == top || y == bottom) {
|
||||
// Draw top/bottom border
|
||||
gfx_word = 0xFFFF;
|
||||
} else if (x == (width-1)) {
|
||||
// Draw right border
|
||||
gfx_word |= 0x0001;
|
||||
} else if (x == 0) {
|
||||
// Draw left border
|
||||
gfx_word |= 0x8000;
|
||||
}
|
||||
write_word(gfx_word);
|
||||
}
|
||||
}
|
||||
|
||||
// Draw the percentage as text in DDRAM
|
||||
|
||||
#if EXTRUDERS == 1
|
||||
set_ddram_address(DDRAM_LINE_3 + 1);
|
||||
#else
|
||||
set_ddram_address(DDRAM_LINE_2 + left);
|
||||
#endif
|
||||
|
||||
begin_data();
|
||||
if(value > 9) {
|
||||
write_number(value,4);
|
||||
write_str(F("% "));
|
||||
} else {
|
||||
write_number(value,3);
|
||||
write_str(F("% "));
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_fan_icon(bool whichIcon) {
|
||||
set_ddram_address(DDRAM_LINE_1+5);
|
||||
begin_data();
|
||||
write_word(whichIcon ? CGRAM_ICON_3_WORD : CGRAM_ICON_4_WORD);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_heat_icon(bool whichIcon, bool heating) {
|
||||
#if EXTRUDERS == 1
|
||||
set_ddram_address(DDRAM_LINE_2);
|
||||
#else
|
||||
set_ddram_address(DDRAM_LINE_3);
|
||||
#endif
|
||||
begin_data();
|
||||
if(heating) {
|
||||
write_word(whichIcon ? CGRAM_ICON_1_WORD : CGRAM_ICON_2_WORD);
|
||||
} else {
|
||||
write_byte(' ');
|
||||
write_byte(' ');
|
||||
}
|
||||
}
|
||||
|
||||
#define FAR(a,b) (((a > b) ? (a-b) : (b-a)) > 1)
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_extruder_1_temp(uint8_t temp, uint8_t target) {
|
||||
set_ddram_address(DDRAM_LINE_1+1);
|
||||
begin_data();
|
||||
write_number(temp);
|
||||
if(target && FAR(temp, target)) {
|
||||
write_str(F("\x1A"));
|
||||
write_number(target);
|
||||
} else {
|
||||
write_str(F(" "));
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_extruder_2_temp(uint8_t temp, uint8_t target) {
|
||||
set_ddram_address(DDRAM_LINE_2+1);
|
||||
begin_data();
|
||||
write_number(temp);
|
||||
if(target && FAR(temp, target)) {
|
||||
write_str(F("\x1A"));
|
||||
write_number(target);
|
||||
} else {
|
||||
write_str(F(" "));
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_bed_temp(uint8_t temp, uint8_t target) {
|
||||
#if EXTRUDERS == 1
|
||||
set_ddram_address(DDRAM_LINE_2+1);
|
||||
#else
|
||||
set_ddram_address(DDRAM_LINE_3+1);
|
||||
#endif
|
||||
begin_data();
|
||||
write_number(temp);
|
||||
if(target && FAR(temp, target)) {
|
||||
write_str(F("\x1A"));
|
||||
write_number(target);
|
||||
} else {
|
||||
write_str(F(" "));
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_fan_speed(uint8_t value) {
|
||||
set_ddram_address(DDRAM_LINE_1+6);
|
||||
begin_data();
|
||||
write_number(value,4);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_print_time(uint32_t elapsed) {
|
||||
const uint8_t hrs = elapsed/3600;
|
||||
const uint8_t min = (elapsed/60)%60;
|
||||
char str[7];
|
||||
sprintf_P(str,hrs > 99 ? PSTR("%03d:%02d") : PSTR(" %02d:%02d"),hrs,min);
|
||||
|
||||
set_ddram_address(DDRAM_LINE_3+5);
|
||||
begin_data();
|
||||
write_str(str);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_feedrate_percentage(uint8_t percentage) {
|
||||
// We only have enough room for the feedrate when
|
||||
// we have one extruder
|
||||
#if EXTRUDERS == 1
|
||||
set_ddram_address(DDRAM_LINE_2+6);
|
||||
begin_data();
|
||||
write_number(percentage,4);
|
||||
#endif
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_status_message(const char *str) {
|
||||
set_ddram_address(DDRAM_LINE_4);
|
||||
begin_data();
|
||||
#if ENABLED(STATUS_MESSAGE_SCROLLING)
|
||||
const uint8_t lcd_len = 16;
|
||||
const uint8_t padding = 2;
|
||||
uint8_t str_len = strlen(str);
|
||||
|
||||
// Trim whitespace at the end of the str, as for some reason
|
||||
// messages like "Card Inserted" are padded with many spaces
|
||||
while(str_len > 0 && str[str_len-1] == ' ') {
|
||||
str_len--;
|
||||
}
|
||||
|
||||
if(str_len <= lcd_len) {
|
||||
// It all fits on the LCD without scrolling
|
||||
write_str(str);
|
||||
} else {
|
||||
// Print the message repeatedly until covering the LCD
|
||||
uint8_t c = status_scroll_pos;
|
||||
for(uint8_t n = 0; n < lcd_len; n++) {
|
||||
write_byte(c < str_len ? str[c] : ' ');
|
||||
c++;
|
||||
c %= str_len + padding; // Wrap around
|
||||
}
|
||||
|
||||
// Scroll the message
|
||||
if(status_scroll_pos == str_len + padding) {
|
||||
status_scroll_pos = 0;
|
||||
} else {
|
||||
status_scroll_pos++;
|
||||
}
|
||||
}
|
||||
#else
|
||||
write_str(str, 16);
|
||||
#endif
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::draw_position(const float x, const float y, const float z, bool position_known) {
|
||||
char str[7];
|
||||
set_ddram_address(DDRAM_LINE_4);
|
||||
begin_data();
|
||||
|
||||
// If position is unknown, flash the labels.
|
||||
const unsigned char alt_label = position_known ? 0 : (lcd_blink() ? ' ' : 0);
|
||||
|
||||
dtostrf(x, -4, 0, str);
|
||||
write_byte(alt_label ? alt_label : 'X');
|
||||
write_str(str, 4);
|
||||
|
||||
dtostrf(y, -4, 0, str);
|
||||
write_byte(alt_label ? alt_label : 'Y');
|
||||
write_str(str, 4);
|
||||
|
||||
dtostrf(z, -5, 1, str);
|
||||
write_byte(alt_label ? alt_label : 'Z');
|
||||
write_str(str, 5);
|
||||
}
|
||||
|
||||
bool ST7920_Lite_Status_Screen::indicators_changed() {
|
||||
// We only add the target temperatures to the checksum
|
||||
// because the actual temps fluctuate so by updating
|
||||
// them only during blinks we gain a bit of stability.
|
||||
const bool blink = lcd_blink();
|
||||
const uint8_t feedrate_perc = feedrate_percentage;
|
||||
const uint8_t fan_speed = ((fanSpeeds[0] + 1) * 100) / 256;
|
||||
const float extruder_1_target = thermalManager.degTargetHotend(0);
|
||||
#if EXTRUDERS == 2
|
||||
const float extruder_2_target = thermalManager.degTargetHotend(1);
|
||||
#endif
|
||||
const float bed_target = thermalManager.degTargetBed();
|
||||
|
||||
static uint8_t last_checksum = 0;
|
||||
|
||||
const uint8_t checksum =
|
||||
uint8_t(blink) ^
|
||||
uint8_t(feedrate_perc) ^
|
||||
uint8_t(fan_speed) ^
|
||||
uint8_t(extruder_1_target) ^
|
||||
#if EXTRUDERS == 2
|
||||
uint8_t(extruder_2_target) ^
|
||||
#endif
|
||||
uint8_t(bed_target);
|
||||
|
||||
if(last_checksum == checksum) {
|
||||
return false;
|
||||
} else {
|
||||
last_checksum = checksum;
|
||||
return true;
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::update_indicators(bool forceUpdate) {
|
||||
if(forceUpdate || indicators_changed()) {
|
||||
const bool blink = lcd_blink();
|
||||
const duration_t elapsed = print_job_timer.duration();
|
||||
const uint32_t seconds_elapsed = elapsed.value;
|
||||
const uint8_t feedrate_perc = feedrate_percentage;
|
||||
const uint8_t fan_speed = ((fanSpeeds[0] + 1) * 100) / 256;
|
||||
const float extruder_1_temp = thermalManager.degHotend(0);
|
||||
const float extruder_1_target = thermalManager.degTargetHotend(0);
|
||||
#if EXTRUDERS == 2
|
||||
const float extruder_2_temp = thermalManager.degHotend(1);
|
||||
const float extruder_2_target = thermalManager.degTargetHotend(1);
|
||||
#endif
|
||||
const float bed_temp = thermalManager.degBed();
|
||||
const float bed_target = thermalManager.degTargetBed();
|
||||
|
||||
draw_extruder_1_temp(extruder_1_temp, extruder_1_target);
|
||||
#if EXTRUDERS == 2
|
||||
draw_extruder_2_temp(extruder_2_temp, extruder_2_target);
|
||||
#endif
|
||||
draw_bed_temp(bed_temp, bed_target);
|
||||
draw_fan_speed(fan_speed);
|
||||
draw_print_time(seconds_elapsed);
|
||||
draw_feedrate_percentage(feedrate_perc);
|
||||
|
||||
// Update the fan and bed animations
|
||||
if(fan_speed > 0) {
|
||||
draw_fan_icon(blink);
|
||||
}
|
||||
if(bed_target > 0) {
|
||||
draw_heat_icon(blink, true);
|
||||
} else {
|
||||
draw_heat_icon(false, false);
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
bool ST7920_Lite_Status_Screen::position_changed() {
|
||||
const float x_pos = current_position[X_AXIS];
|
||||
const float y_pos = current_position[Y_AXIS];
|
||||
const float z_pos = current_position[Z_AXIS];
|
||||
const uint8_t checksum = uint8_t(x_pos) ^ uint8_t(y_pos) ^ uint8_t(z_pos);
|
||||
|
||||
static uint8_t last_checksum = 0;
|
||||
if(last_checksum == checksum) {
|
||||
return false;
|
||||
} else {
|
||||
last_checksum = checksum;
|
||||
return true;
|
||||
}
|
||||
}
|
||||
|
||||
bool ST7920_Lite_Status_Screen::status_changed() {
|
||||
uint8_t checksum = 0;
|
||||
for(const char *p = lcd_status_message; *p; p++) {
|
||||
checksum ^= *p;
|
||||
}
|
||||
|
||||
static uint8_t last_checksum = 0;
|
||||
if(last_checksum == checksum) {
|
||||
return false;
|
||||
} else {
|
||||
last_checksum = checksum;
|
||||
return true;
|
||||
}
|
||||
}
|
||||
|
||||
bool ST7920_Lite_Status_Screen::blink_changed() {
|
||||
static uint8_t last_blink = 0;
|
||||
|
||||
const bool blink = lcd_blink();
|
||||
if(last_blink == blink) {
|
||||
return false;
|
||||
} else {
|
||||
last_blink = blink;
|
||||
return true;
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::update_status_or_position(bool forceUpdate) {
|
||||
static uint8_t countdown = 0;
|
||||
|
||||
/* There is only enough room in the display for either the
|
||||
* status message or the position, not both, so we choose
|
||||
* one or another. Whenever the status message changes,
|
||||
* we show it for a number of consecutive seconds, but
|
||||
* then go back to showing the position as soon as the
|
||||
* head moves, i.e:
|
||||
*
|
||||
* countdown > 1 -- Show status
|
||||
* countdown = 1 -- Show status, until movement
|
||||
* countdown = 0 -- Show position
|
||||
*/
|
||||
if( forceUpdate || status_changed() ) {
|
||||
#if ENABLED(STATUS_MESSAGE_SCROLLING)
|
||||
status_scroll_pos = 0;
|
||||
#endif
|
||||
if(lcd_strlen(lcd_status_message)) {
|
||||
countdown = DELAY_TO_SHOW_POSITION;
|
||||
} else {
|
||||
countdown = 0;
|
||||
}
|
||||
draw_status_message(lcd_status_message);
|
||||
blink_changed(); // Clear changed flag
|
||||
}
|
||||
else if(countdown > 1 && blink_changed() ) {
|
||||
countdown--;
|
||||
#if ENABLED(STATUS_MESSAGE_SCROLLING)
|
||||
draw_status_message(lcd_status_message);
|
||||
#endif
|
||||
}
|
||||
else if(countdown > 0 && blink_changed() ) {
|
||||
if(position_changed()) {
|
||||
countdown--;
|
||||
forceUpdate = true;
|
||||
}
|
||||
#if ENABLED(STATUS_MESSAGE_SCROLLING)
|
||||
draw_status_message(lcd_status_message);
|
||||
#endif
|
||||
}
|
||||
if(countdown == 0 && (forceUpdate || position_changed() ||
|
||||
#if DISABLED(DISABLE_REDUCED_ACCURACY_WARNING)
|
||||
blink_changed()
|
||||
#endif
|
||||
)) {
|
||||
draw_position(
|
||||
current_position[X_AXIS],
|
||||
current_position[Y_AXIS],
|
||||
current_position[Z_AXIS],
|
||||
#if ENABLED(DISABLE_REDUCED_ACCURACY_WARNING)
|
||||
true
|
||||
#else
|
||||
axis_known_position[X_AXIS] &&
|
||||
axis_known_position[Y_AXIS] &&
|
||||
axis_known_position[Z_AXIS]
|
||||
#endif
|
||||
);
|
||||
}
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::update_progress(bool forceUpdate) {
|
||||
#if ENABLED(SDSUPPORT)
|
||||
const uint8_t percent_done = card.percentDone();
|
||||
#else
|
||||
const uint8_t percent_done = 0;
|
||||
#endif
|
||||
|
||||
// Since the progress bar involves writing
|
||||
// quite a few bytes to GDRAM, only do this
|
||||
// when an update is actually necessary.
|
||||
|
||||
static uint8_t last_progress = 0;
|
||||
if(!forceUpdate && last_progress == percent_done)
|
||||
return;
|
||||
last_progress = percent_done;
|
||||
|
||||
draw_progress_bar(percent_done);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::update(bool forceUpdate) {
|
||||
cs();
|
||||
update_indicators(forceUpdate);
|
||||
update_status_or_position(forceUpdate);
|
||||
update_progress(forceUpdate);
|
||||
ncs();
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::reset_state_from_unknown() {
|
||||
_extended_function_set(true, true); // Do it twice as only one bit
|
||||
_extended_function_set(true, true); // get set at a time.
|
||||
_scroll_or_addr_select(false);
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::on_entry() {
|
||||
cs();
|
||||
reset_state_from_unknown();
|
||||
clear();
|
||||
clear_gdram();
|
||||
draw_static_elements();
|
||||
update(true);
|
||||
ncs();
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::on_exit() {
|
||||
cs();
|
||||
clear();
|
||||
_extended_function_set(true, true); // Restore state to what u8g expects.
|
||||
ncs();
|
||||
}
|
||||
|
||||
// This is called prior to the KILL screen to
|
||||
// clear the screen so we don't end up with a
|
||||
// garbled display.
|
||||
void ST7920_Lite_Status_Screen::clear_text_buffer() {
|
||||
cs();
|
||||
reset_state_from_unknown();
|
||||
clear();
|
||||
_extended_function_set(true, true); // Restore state to what u8g expects.
|
||||
ncs();
|
||||
}
|
||||
|
||||
static void lcd_implementation_status_screen() {
|
||||
ST7920_Lite_Status_Screen::update(false);
|
||||
}
|
||||
|
||||
/* In order to properly update the lite status screen,
|
||||
* we must know when we have entered and left the
|
||||
* status screen. Since the ultralcd code is not
|
||||
* set up for doing this, we call this function before
|
||||
* each update indicating whether the current screen
|
||||
* is the status screen.
|
||||
*
|
||||
* This function keeps track of whether we have left or
|
||||
* entered the status screen and calls the on_entry()
|
||||
* and on_exit() methods for cleanup.
|
||||
*/
|
||||
|
||||
static void lcd_in_status(bool inStatus) {
|
||||
static bool lastInStatus = false;
|
||||
if(!lastInStatus && inStatus) {
|
||||
ST7920_Lite_Status_Screen::on_entry();
|
||||
lastInStatus = true;
|
||||
}
|
||||
if(lastInStatus && !inStatus) {
|
||||
ST7920_Lite_Status_Screen::on_exit();
|
||||
lastInStatus = false;
|
||||
}
|
||||
}
|
||||
@@ -0,0 +1,39 @@
|
||||
/*
|
||||
* Lightweight Status Screen for the RepRapDiscount Full
|
||||
* Graphics Smart Controller (ST7920-based 128x64 LCD)
|
||||
*
|
||||
* (c) 2017 Aleph Objects, Inc.
|
||||
*
|
||||
* The code in this page is free software: you can
|
||||
* redistribute it and/or modify it under the terms of the GNU
|
||||
* General Public License (GNU GPL) as published by the Free Software
|
||||
* Foundation, either version 3 of the License, or (at your option)
|
||||
* any later version. The code is distributed WITHOUT ANY WARRANTY;
|
||||
* without even the implied warranty of MERCHANTABILITY or FITNESS
|
||||
* FOR A PARTICULAR PURPOSE. See the GNU GPL for more details.
|
||||
*
|
||||
*/
|
||||
|
||||
#include "ultralcd_impl_st7920_lite_status_screen.h"
|
||||
|
||||
void ST7920_Lite_Status_Screen::cs() {
|
||||
ST7920_CS();
|
||||
current_bits.synced = false;
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::ncs() {
|
||||
ST7920_NCS();
|
||||
current_bits.synced = false;
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::sync_cmd() {
|
||||
ST7920_SET_CMD();
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::sync_dat() {
|
||||
ST7920_SET_DAT();
|
||||
}
|
||||
|
||||
void ST7920_Lite_Status_Screen::write_byte(uint8_t data) {
|
||||
ST7920_WRITE_NIBBLES(data);
|
||||
}
|
||||
@@ -124,10 +124,12 @@ uint8_t u8g_dev_rrd_st7920_128x64_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, vo
|
||||
ST7920_CS();
|
||||
u8g_Delay(120); //initial delay for boot up
|
||||
ST7920_SET_CMD();
|
||||
ST7920_WRITE_BYTE(0x20); //non-extended mode
|
||||
ST7920_WRITE_BYTE(0x08); //display off, cursor+blink off
|
||||
ST7920_WRITE_BYTE(0x01); //clear CGRAM ram
|
||||
u8g_Delay(15); //delay for CGRAM clear
|
||||
ST7920_WRITE_BYTE(0x3E); //extended mode + GDRAM active
|
||||
ST7920_WRITE_BYTE(0x01); //clear DDRAM ram
|
||||
u8g_Delay(15); //delay for DDRAM clear
|
||||
ST7920_WRITE_BYTE(0x24); //extended mode
|
||||
ST7920_WRITE_BYTE(0x26); //extended mode + GDRAM active
|
||||
for (y = 0; y < (LCD_PIXEL_HEIGHT) / 2; y++) { //clear GDRAM
|
||||
ST7920_WRITE_BYTE(0x80 | y); //set y
|
||||
ST7920_WRITE_BYTE(0x80); //set x = 0
|
||||
@@ -181,6 +183,14 @@ uint8_t u8g_dev_st7920_128x64_rrd_buf[(LCD_PIXEL_WIDTH) * (PAGE_HEIGHT) / 8] U
|
||||
u8g_pb_t u8g_dev_st7920_128x64_rrd_pb = {{PAGE_HEIGHT, LCD_PIXEL_HEIGHT, 0, 0, 0}, LCD_PIXEL_WIDTH, u8g_dev_st7920_128x64_rrd_buf};
|
||||
u8g_dev_t u8g_dev_st7920_128x64_rrd_sw_spi = {u8g_dev_rrd_st7920_128x64_fn, &u8g_dev_st7920_128x64_rrd_pb, &u8g_com_null_fn};
|
||||
|
||||
#if ENABLED(USE_ST7920_LIGHTWEIGHT_UI)
|
||||
typedef const __FlashStringHelper *progmem_str;
|
||||
|
||||
// We have to include the code for the lightweight UI here
|
||||
// as it relies on macros that are only defined in this file.
|
||||
#include "ultralcd_impl_st7920_lite_status_screen_impl_spi.h"
|
||||
#endif
|
||||
|
||||
#pragma GCC reset_options
|
||||
|
||||
#endif // U8G_HAL_LINKS
|
||||
|
||||
@@ -5116,20 +5116,38 @@ void lcd_update() {
|
||||
#endif
|
||||
|
||||
#if ENABLED(DOGLCD)
|
||||
if (!drawing_screen) { // If not already drawing pages
|
||||
u8g.firstPage(); // Start the first page
|
||||
drawing_screen = 1; // Flag as drawing pages
|
||||
}
|
||||
lcd_setFont(FONT_MENU); // Setup font for every page draw
|
||||
u8g.setColorIndex(1); // And reset the color
|
||||
CURRENTSCREEN(); // Draw and process the current screen
|
||||
#if defined(USE_ST7920_LIGHTWEIGHT_UI)
|
||||
#if ENABLED(ULTIPANEL)
|
||||
bool do_U8G_loop = true;
|
||||
lcd_in_status(currentScreen == lcd_status_screen);
|
||||
if(currentScreen == lcd_status_screen) {
|
||||
lcd_status_screen();
|
||||
do_U8G_loop = false;
|
||||
}
|
||||
#else
|
||||
const bool do_U8G_loop = false;
|
||||
lcd_in_status(true);
|
||||
lcd_status_screen();
|
||||
#endif
|
||||
#else
|
||||
const bool do_U8G_loop = true;
|
||||
#endif
|
||||
if(do_U8G_loop) {
|
||||
if (!drawing_screen) { // If not already drawing pages
|
||||
u8g.firstPage(); // Start the first page
|
||||
drawing_screen = 1; // Flag as drawing pages
|
||||
}
|
||||
lcd_setFont(FONT_MENU); // Setup font for every page draw
|
||||
u8g.setColorIndex(1); // And reset the color
|
||||
CURRENTSCREEN(); // Draw and process the current screen
|
||||
|
||||
// The screen handler can clear drawing_screen for an action that changes the screen.
|
||||
// If still drawing and there's another page, update max-time and return now.
|
||||
// The nextPage will already be set up on the next call.
|
||||
if (drawing_screen && (drawing_screen = u8g.nextPage())) {
|
||||
NOLESS(max_display_update_time, millis() - ms);
|
||||
return;
|
||||
// The screen handler can clear drawing_screen for an action that changes the screen.
|
||||
// If still drawing and there's another page, update max-time and return now.
|
||||
// The nextPage will already be set up on the next call.
|
||||
if (drawing_screen && (drawing_screen = u8g.nextPage())) {
|
||||
NOLESS(max_display_update_time, millis() - ms);
|
||||
return;
|
||||
}
|
||||
}
|
||||
#else
|
||||
CURRENTSCREEN();
|
||||
|
||||
@@ -54,6 +54,11 @@
|
||||
|
||||
#include "dogm/dogm_bitmaps.h"
|
||||
|
||||
#if ENABLED(USE_ST7920_LIGHTWEIGHT_UI)
|
||||
typedef const __FlashStringHelper *progmem_str;
|
||||
#include "dogm/ultralcd_impl_st7920_lite_status_screen_impl.h"
|
||||
#endif
|
||||
|
||||
#if ENABLED(SDSUPPORT)
|
||||
#include "../libs/duration_t.h"
|
||||
#endif
|
||||
@@ -373,6 +378,9 @@ static void lcd_implementation_init() {
|
||||
|
||||
// The kill screen is displayed for unrecoverable conditions
|
||||
void lcd_kill_screen() {
|
||||
#if ENABLED(USE_ST7920_LIGHTWEIGHT_UI)
|
||||
ST7920_Lite_Status_Screen::clear_text_buffer();
|
||||
#endif
|
||||
const uint8_t h4 = u8g.getHeight() / 4;
|
||||
u8g.firstPage();
|
||||
do {
|
||||
@@ -498,6 +506,7 @@ inline void lcd_implementation_status_message(const bool blink) {
|
||||
#endif
|
||||
}
|
||||
|
||||
#if !ENABLED(USE_ST7920_LIGHTWEIGHT_UI)
|
||||
static void lcd_implementation_status_screen() {
|
||||
|
||||
const bool blink = lcd_blink();
|
||||
@@ -801,6 +810,7 @@ static void lcd_implementation_status_screen() {
|
||||
#endif
|
||||
}
|
||||
}
|
||||
#endif
|
||||
|
||||
#if ENABLED(ULTIPANEL)
|
||||
|
||||
|
||||
Reference in New Issue
Block a user