From 8f8bf3a897621c08afd42e9b854a28ac5f0ac287 Mon Sep 17 00:00:00 2001 From: brupje Date: Tue, 5 May 2015 11:03:20 +0200 Subject: [PATCH 1/8] Make Marlin actually compile when #define REPRAPWORLD_KEYPAD is uncommented --- Marlin/ultralcd.cpp | 8 ++++---- Marlin/ultralcd_implementation_hitachi_HD44780.h | 10 +++++----- 2 files changed, 9 insertions(+), 9 deletions(-) diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index 5ca0943376..15c20fff3a 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -212,11 +212,11 @@ static void lcd_status_screen(); } } while(0) /** Used variables to keep track of the menu */ - #ifndef REPRAPWORLD_KEYPAD - volatile uint8_t buttons; // Bits of the pressed buttons. - #else - volatile uint8_t buttons_reprapworld_keypad; // The reprapworld_keypad shift register values + volatile uint8_t buttons; //the last checked buttons in a bit array. + #ifdef REPRAPWORLD_KEYPAD + volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values #endif + #ifdef LCD_HAS_SLOW_BUTTONS volatile uint8_t slow_buttons; // Bits of the pressed buttons. #endif diff --git a/Marlin/ultralcd_implementation_hitachi_HD44780.h b/Marlin/ultralcd_implementation_hitachi_HD44780.h index eb1f525cc2..b5b046da3b 100644 --- a/Marlin/ultralcd_implementation_hitachi_HD44780.h +++ b/Marlin/ultralcd_implementation_hitachi_HD44780.h @@ -6,11 +6,11 @@ * When selecting the Russian language, a slightly different LCD implementation is used to handle UTF8 characters. **/ -#ifndef REPRAPWORLD_KEYPAD - extern volatile uint8_t buttons; //the last checked buttons in a bit array. -#else - extern volatile uint16_t buttons; //an extended version of the last checked buttons in a bit array. -#endif +//#ifndef REPRAPWORLD_KEYPAD +// extern volatile uint8_t buttons; //the last checked buttons in a bit array. +//#else + extern volatile uint8_t buttons; //an extended version of the last checked buttons in a bit array. +//#endif //////////////////////////////////// // Setup button and encode mappings for each panel (into 'buttons' variable From df4d50579a07eb61159e80eea30637b72103e494 Mon Sep 17 00:00:00 2001 From: brupje Date: Tue, 5 May 2015 12:47:24 +0200 Subject: [PATCH 2/8] This is conflicting with the settings in ultralcd.h. Not sure why it' s redefined here anyway. --- Marlin/ultralcd_implementation_hitachi_HD44780.h | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/Marlin/ultralcd_implementation_hitachi_HD44780.h b/Marlin/ultralcd_implementation_hitachi_HD44780.h index b5b046da3b..2d84b76733 100644 --- a/Marlin/ultralcd_implementation_hitachi_HD44780.h +++ b/Marlin/ultralcd_implementation_hitachi_HD44780.h @@ -83,7 +83,7 @@ #define BLEN_REPRAPWORLD_KEYPAD_DOWN 6 #define BLEN_REPRAPWORLD_KEYPAD_LEFT 7 - #define REPRAPWORLD_BTN_OFFSET 3 // bit offset into buttons for shift register values + #define REPRAPWORLD_BTN_OFFSET 0 // bit offset into buttons for shift register values #define EN_REPRAPWORLD_KEYPAD_F3 BIT((BLEN_REPRAPWORLD_KEYPAD_F3+REPRAPWORLD_BTN_OFFSET)) #define EN_REPRAPWORLD_KEYPAD_F2 BIT((BLEN_REPRAPWORLD_KEYPAD_F2+REPRAPWORLD_BTN_OFFSET)) @@ -94,10 +94,10 @@ #define EN_REPRAPWORLD_KEYPAD_DOWN BIT((BLEN_REPRAPWORLD_KEYPAD_DOWN+REPRAPWORLD_BTN_OFFSET)) #define EN_REPRAPWORLD_KEYPAD_LEFT BIT((BLEN_REPRAPWORLD_KEYPAD_LEFT+REPRAPWORLD_BTN_OFFSET)) - #define LCD_CLICKED ((buttons&EN_C) || (buttons&EN_REPRAPWORLD_KEYPAD_F1)) - #define REPRAPWORLD_KEYPAD_MOVE_Y_DOWN (buttons&EN_REPRAPWORLD_KEYPAD_DOWN) - #define REPRAPWORLD_KEYPAD_MOVE_Y_UP (buttons&EN_REPRAPWORLD_KEYPAD_UP) - #define REPRAPWORLD_KEYPAD_MOVE_HOME (buttons&EN_REPRAPWORLD_KEYPAD_MIDDLE) + //#define LCD_CLICKED ((buttons&EN_C) || (buttons&EN_REPRAPWORLD_KEYPAD_F1)) + //#define REPRAPWORLD_KEYPAD_MOVE_Y_DOWN (buttons&EN_REPRAPWORLD_KEYPAD_DOWN) + //#define REPRAPWORLD_KEYPAD_MOVE_Y_UP (buttons&EN_REPRAPWORLD_KEYPAD_UP) + //#define REPRAPWORLD_KEYPAD_MOVE_HOME (buttons&EN_REPRAPWORLD_KEYPAD_MIDDLE) #elif defined(NEWPANEL) #define LCD_CLICKED (buttons&EN_C) From 816aa19861344e3d5ceaed07a0ce9e1d5b833444 Mon Sep 17 00:00:00 2001 From: brupje Date: Tue, 5 May 2015 13:04:46 +0200 Subject: [PATCH 3/8] Up/down buttons were reversed, swapped the assignments --- Marlin/ultralcd_implementation_hitachi_HD44780.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/Marlin/ultralcd_implementation_hitachi_HD44780.h b/Marlin/ultralcd_implementation_hitachi_HD44780.h index 2d84b76733..7f9a88e5b1 100644 --- a/Marlin/ultralcd_implementation_hitachi_HD44780.h +++ b/Marlin/ultralcd_implementation_hitachi_HD44780.h @@ -77,10 +77,10 @@ #define BLEN_REPRAPWORLD_KEYPAD_F3 0 #define BLEN_REPRAPWORLD_KEYPAD_F2 1 #define BLEN_REPRAPWORLD_KEYPAD_F1 2 - #define BLEN_REPRAPWORLD_KEYPAD_UP 3 + #define BLEN_REPRAPWORLD_KEYPAD_UP 6 #define BLEN_REPRAPWORLD_KEYPAD_RIGHT 4 #define BLEN_REPRAPWORLD_KEYPAD_MIDDLE 5 - #define BLEN_REPRAPWORLD_KEYPAD_DOWN 6 + #define BLEN_REPRAPWORLD_KEYPAD_DOWN 3 #define BLEN_REPRAPWORLD_KEYPAD_LEFT 7 #define REPRAPWORLD_BTN_OFFSET 0 // bit offset into buttons for shift register values From 22e0d2afcb5828b3a62099f786c0cdd45406b4de Mon Sep 17 00:00:00 2001 From: brupje Date: Tue, 5 May 2015 14:01:20 +0200 Subject: [PATCH 4/8] Default configuration for megatronics. --- Marlin/rrw/Configuration_megatronics.h | 817 +++++++++++++++++++++++++ 1 file changed, 817 insertions(+) create mode 100644 Marlin/rrw/Configuration_megatronics.h diff --git a/Marlin/rrw/Configuration_megatronics.h b/Marlin/rrw/Configuration_megatronics.h new file mode 100644 index 0000000000..c628459891 --- /dev/null +++ b/Marlin/rrw/Configuration_megatronics.h @@ -0,0 +1,817 @@ +#ifndef CONFIGURATION_H +#define CONFIGURATION_H + +#include "boards.h" + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== +/* +Here are some standard links for getting your machine calibrated: + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 +*/ + +// This configuration file contains the basic settings. +// Advanced settings can be found in Configuration_adv.h +// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer replace the configuration files with the files in the +// example_configurations/delta directory. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a Scara printer replace the configuration files with the files in the +// example_configurations/SCARA directory. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_VERSION "1.0.3 dev" +#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time +#define STRING_CONFIG_H_AUTHOR "RepRapWorld.com" // Who made the changes. +#define STRING_SPLASH_LINE1 "v" STRING_VERSION // will be shown during bootup in line 1 +//#define STRING_SPLASH_LINE2 STRING_VERSION_CONFIG_H // will be shown during bootup in line2 + +// @section machine + +// SERIAL_PORT selects which serial port should be used for communication with the host. +// This allows the connection of wireless adapters (for instance) to non-default port pins. +// Serial port 0 is still used by the Arduino bootloader regardless of this setting. +// :[0,1,2,3,4,5,6,7] +#define SERIAL_PORT 0 + +// This determines the communication speed of the printer +// :[2400,9600,19200,38400,57600,115200,250000] +#define BAUDRATE 250000 + +// This enables the serial port associated to the Bluetooth interface +//#define BTENABLED // Enable BT interface on AT90USB devices + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_MEGATRONICS_3 +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +// #define CUSTOM_MACHINE_NAME "3D Printer" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// This defines the number of extruders +// :[1,2,3,4] +#define EXTRUDERS 1 + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + +//// The following define selects which power supply you have. Please choose the one that matches your setup +// 1 = ATX +// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) +// :{1:'ATX',2:'X-Box 360'} + +#define POWER_SUPPLY 1 + +// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. +// #define PS_DEFAULT_OFF + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== +// +//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table +// +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used +// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) +// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) +// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! +// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) +// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) +// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) +// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) +// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) +// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) +// 10 is 100k RS thermistor 198-961 (4.7k pullup) +// 11 is 100k beta 3950 1% thermistor (4.7k pullup) +// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) +// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" +// 20 is the PT100 circuit found in the Ultimainboard V2.x +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 +// +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// (but gives greater accuracy and more stable PID) +// 51 is 100k thermistor - EPCOS (1k pullup) +// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) +// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) +// +// 1047 is Pt1000 with 4k7 pullup +// 1010 is Pt1000 with 1k pullup (non standard) +// 147 is Pt100 with 4k7 pullup +// 110 is Pt100 with 1k pullup (non standard) +// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below. +// Use it for Testing or Development purposes. NEVER for production machine. +// #define DUMMY_THERMISTOR_998_VALUE 25 +// #define DUMMY_THERMISTOR_999_VALUE 100 +// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" } +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_BED 1 + +// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +// Actual temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define BED_MAXTEMP 150 + +// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the +// average current. The value should be an integer and the heat bed will be turned on for 1 interval of +// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. +//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 + +// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS +//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#ifdef PIDTEMP + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term + #define K1 0.95 //smoothing factor within the PID + #define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine + +// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it +// Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + +// MakerGear +// #define DEFAULT_Kp 7.0 +// #define DEFAULT_Ki 0.1 +// #define DEFAULT_Kd 12 + +// Mendel Parts V9 on 12V +// #define DEFAULT_Kp 63.0 +// #define DEFAULT_Ki 2.25 +// #define DEFAULT_Kd 440 +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +//#define PIDTEMPBED +// +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +//#define PID_BED_DEBUG // Sends debug data to the serial port. + +#ifdef PIDTEMPBED +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from pidautotune +// #define DEFAULT_bedKp 97.1 +// #define DEFAULT_bedKi 1.41 +// #define DEFAULT_bedKd 1675.16 + +// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit +//can be software-disabled for whatever purposes by +#define PREVENT_DANGEROUS_EXTRUDE +//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately. +#define PREVENT_LENGTHY_EXTRUDE + +#define EXTRUDE_MINTEMP 170 +#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. + +//=========================================================================== +//============================= Thermal Runaway Protection ================== +//=========================================================================== +/* +This is a feature to protect your printer from burn up in flames if it has +a thermistor coming off place (this happened to a friend of mine recently and +motivated me writing this feature). + +The issue: If a thermistor come off, it will read a lower temperature than actual. +The system will turn the heater on forever, burning up the filament and anything +else around. + +After the temperature reaches the target for the first time, this feature will +start measuring for how long the current temperature stays below the target +minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). + +If it stays longer than _PERIOD, it means the thermistor temperature +cannot catch up with the target, so something *may be* wrong. Then, to be on the +safe side, the system will he halt. + +Bear in mind the count down will just start AFTER the first time the +thermistor temperature is over the target, so you will have no problem if +your extruder heater takes 2 minutes to hit the target on heating. + +*/ +// If you want to enable this feature for all your extruder heaters, +// uncomment the 2 defines below: + +// Parameters for all extruder heaters +#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds +#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius + +// If you want to enable this feature for your bed heater, +// uncomment the 2 defines below: + +// Parameters for the bed heater +#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds +#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius + + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment this option to enable CoreXY kinematics +// #define COREXY + +// Enable this option for Toshiba steppers +// #define CONFIG_STEPPERS_TOSHIBA + +// @section homing + +// coarse Endstop Settings +#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors + +#ifndef ENDSTOPPULLUPS + // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined + // #define ENDSTOPPULLUP_XMAX + // #define ENDSTOPPULLUP_YMAX + // #define ENDSTOPPULLUP_ZMAX + // #define ENDSTOPPULLUP_XMIN + // #define ENDSTOPPULLUP_YMIN + // #define ENDSTOPPULLUP_ZMIN + // #define ENDSTOPPULLUP_ZPROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. +//#define DISABLE_MAX_ENDSTOPS +//#define DISABLE_MIN_ENDSTOPS + +// @section machine +// If you want to enable the Z Probe pin, but disable its use, uncomment the line below. +// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have +// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe, +// this has no effect. +//#define DISABLE_Z_PROBE_ENDSTOP + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{0:'Low',1:'High'} +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR false +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false + +// @section homing + +// ENDSTOP SETTINGS: +// Sets direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. +#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. + +// @section machine + +// Travel limits after homing (units are in mm) +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS 200 +#define Y_MAX_POS 200 +#define Z_MAX_POS 200 + +//=========================================================================== +//============================= Filament Runout Sensor ====================== +//=========================================================================== +//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament + // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. + // It is assumed that when logic high = filament available + // when logic low = filament ran out +//const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned +//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. + +//=========================================================================== +//============================ Mesh Bed Leveling ============================ +//=========================================================================== + +// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling +// #define MESH_BED_LEVELING // Enable mesh bed leveling + +#ifdef MANUAL_BED_LEVELING + #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis +#endif // MANUAL_BED_LEVELING + +#ifdef MESH_BED_LEVELING + #define MESH_MIN_X 10 + #define MESH_MAX_X (X_MAX_POS - MESH_MIN_X) + #define MESH_MIN_Y 10 + #define MESH_MAX_Y (Y_MAX_POS - MESH_MIN_Y) + #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited + #define MESH_NUM_Y_POINTS 3 + #define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0 +#endif // MESH_BED_LEVELING + +//=========================================================================== +//============================= Bed Auto Leveling =========================== +//=========================================================================== + +// @section bedlevel + +//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) +#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. + +#ifdef ENABLE_AUTO_BED_LEVELING + + // There are 2 different ways to specify probing locations + // + // - "grid" mode + // Probe several points in a rectangular grid. + // You specify the rectangle and the density of sample points. + // This mode is preferred because there are more measurements. + // + // - "3-point" mode + // Probe 3 arbitrary points on the bed (that aren't colinear) + // You specify the XY coordinates of all 3 points. + + // Enable this to sample the bed in a grid (least squares solution) + // Note: this feature generates 10KB extra code size + #define AUTO_BED_LEVELING_GRID + + #ifdef AUTO_BED_LEVELING_GRID + + #define LEFT_PROBE_BED_POSITION 15 + #define RIGHT_PROBE_BED_POSITION 170 + #define FRONT_PROBE_BED_POSITION 20 + #define BACK_PROBE_BED_POSITION 170 + + #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this + + // Set the number of grid points per dimension + // You probably don't need more than 3 (squared=9) + #define AUTO_BED_LEVELING_GRID_POINTS 2 + + #else // !AUTO_BED_LEVELING_GRID + + // Arbitrary points to probe. A simple cross-product + // is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 + + #endif // AUTO_BED_LEVELING_GRID + + // Offsets to the probe relative to the extruder tip (Hotend - Probe) + // X and Y offsets must be integers + #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // Probe on: -left +right + #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Probe on: -front +behind + #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!) + + #define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance. + // Be sure you have this distance over your Z_MAX_POS in case + + #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min + + #define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point. + #define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points + #define Z_RAISE_AFTER_PROBING 15 //How much the extruder will be raised after the last probing point. + +// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. + //Useful to retract a deployable probe. + + //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell + //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + + //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk + //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it. + // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile. + +// #define PROBE_SERVO_DEACTIVATION_DELAY 300 + + +//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, +//it is highly recommended you let this Z_SAFE_HOMING enabled!!! + + #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area. + // When defined, it will: + // - Allow Z homing only after X and Y homing AND stepper drivers still enabled + // - If stepper drivers timeout, it will need X and Y homing again before Z homing + // - Position the probe in a defined XY point before Z Homing when homing all axis (G28) + // - Block Z homing only when the probe is outside bed area. + + #ifdef Z_SAFE_HOMING + + #define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28) + #define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28) + + #endif + + // Support for a dedicated Z PROBE endstop separate from the Z MIN endstop. + // If you would like to use both a Z PROBE and a Z MIN endstop together or just a Z PROBE with a custom pin, uncomment #define Z_PROBE_ENDSTOP and read the instructions below. + // If you want to still use the Z min endstop for homing, disable Z_SAFE_HOMING above. Eg; to park the head outside the bed area when homing with G28. + // WARNING: The Z MIN endstop will need to set properly as it would without a Z PROBE to prevent head crashes and premature stopping during a print. + // To use a separate Z PROBE endstop, you must have a Z_PROBE_PIN defined in the pins.h file for your control board. + // If you are using a servo based Z PROBE, you will need to enable NUM_SERVOS, SERVO_ENDSTOPS and SERVO_ENDSTOPS_ANGLES in the R/C Servo below. + // RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board. Use 5V for powered sensors, otherwise connect to ground and D32 + // for normally closed configuration and 5V and D32 for normally open configurations. Normally closed configuration is advised and assumed. + // The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin. Z_PROBE_PIN is setting the pin to use on the Arduino. Since the D32 pin on the RAMPS maps to D32 on Arduino, this works. + // D32 is currently selected in the RAMPS 1.3/1.4 pin file. All other boards will need changes to the respective pins_XXXXX.h file. + // WARNING: Setting the wrong pin may have unexpected and potentially disastrous outcomes. Use with caution and do your homework. + + //#define Z_PROBE_ENDSTOP + +#endif // ENABLE_AUTO_BED_LEVELING + + +// @section homing + +// The position of the homing switches +//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used +//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) + +// Manual homing switch locations: +// For deltabots this means top and center of the Cartesian print volume. +#ifdef MANUAL_HOME_POSITIONS + #define MANUAL_X_HOME_POS 0 + #define MANUAL_Y_HOME_POS 0 + #define MANUAL_Z_HOME_POS 0 + //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing. +#endif + +// @section movement + +/** + * MOVEMENT SETTINGS + */ + +#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) + +// default settings + +#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402*2,78.7402*2,5120.00,760*1*1.5} // default steps per unit for Ultimaker +#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) +#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. + +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves + +// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) +#define DEFAULT_XYJERK 20.0 // (mm/sec) +#define DEFAULT_ZJERK 0.4 // (mm/sec) +#define DEFAULT_EJERK 5.0 // (mm/sec) + + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section more + +// Custom M code points +#define CUSTOM_M_CODES +#ifdef CUSTOM_M_CODES + #ifdef ENABLE_AUTO_BED_LEVELING + #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851 + #define Z_PROBE_OFFSET_RANGE_MIN -20 + #define Z_PROBE_OFFSET_RANGE_MAX 20 + #endif +#endif + +// @section extras + +// EEPROM +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +//define this to enable EEPROM support +//#define EEPROM_SETTINGS + +#ifdef EEPROM_SETTINGS + // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: + #define EEPROM_CHITCHAT // please keep turned on if you can. +#endif + + +// @section temperature + +// Preheat Constants +#define PLA_PREHEAT_HOTEND_TEMP 180 +#define PLA_PREHEAT_HPB_TEMP 70 +#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 + +#define ABS_PREHEAT_HOTEND_TEMP 240 +#define ABS_PREHEAT_HPB_TEMP 110 +#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 + +//==============================LCD and SD support============================= +// @section lcd + +// Define your display language below. Replace (en) with your language code and uncomment. +// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test +// See also language.h +#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) + +// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display. +// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset. +// See also documentation/LCDLanguageFont.md + #define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware + //#define DISPLAY_CHARSET_HD44780_WESTERN + //#define DISPLAY_CHARSET_HD44780_CYRILLIC + +#define ULTRA_LCD //general LCD support, also 16x2 +//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) +#define SDSUPPORT // Enable SD Card Support in Hardware Console +//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication +//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder +//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking +//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. +//#define ULTIPANEL //the UltiPanel as on Thingiverse +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click + // 0 to disable buzzer feedback. Test with M300 S P +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +//#define PANEL_ONE + +// The MaKr3d Makr-Panel with graphic controller and SD support +// http://reprap.org/wiki/MaKr3d_MaKrPanel +//#define MAKRPANEL + +// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD +// http://panucatt.com +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +//#define VIKI2 +//#define miniVIKI + +// The RepRapDiscount Smart Controller (white PCB) +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// The GADGETS3D G3D LCD/SD Controller (blue PCB) +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +//#define G3D_PANEL + +// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB) +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// The RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +#define REPRAPWORLD_KEYPAD +#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click + +// The Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C +//#define RA_CONTROL_PANEL + +/** + * I2C Panels + */ + +//#define LCD_I2C_SAINSMART_YWROBOT + +// PANELOLU2 LCD with status LEDs, separate encoder and click inputs +//#define LCD_I2C_PANELOLU2 + +// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs +//#define LCD_I2C_VIKI + +// Shift register panels +// --------------------- +// 2 wire Non-latching LCD SR from: +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection + +//#define SAV_3DLCD + +// @section extras + +// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// Temperature status LEDs that display the hotend and bet temperature. +// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on. +// Otherwise the RED led is on. There is 1C hysteresis. +//#define TEMP_STAT_LEDS + +// M240 Triggers a camera by emulating a Canon RC-1 Remote +// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +// #define PHOTOGRAPH_PIN 23 + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder. +//#define BARICUDA + +//define BlinkM/CyzRgb Support +//#define BLINKM + +/*********************************************************************\ +* R/C SERVO support +* Sponsored by TrinityLabs, Reworked by codexmas +**********************************************************************/ + +// Number of servos +// +// If you select a configuration below, this will receive a default value and does not need to be set manually +// set it manually if you have more servos than extruders and wish to manually control some +// leaving it undefined or defining as 0 will disable the servo subsystem +// If unsure, leave commented / disabled +// +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Servo Endstops +// +// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. +// Use M851 to set the z-probe vertical offset from the nozzle. Store that setting with M500. +// +//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1 +//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles + +/**********************************************************************\ + * Support for a filament diameter sensor + * Also allows adjustment of diameter at print time (vs at slicing) + * Single extruder only at this point (extruder 0) + * + * Motherboards + * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector + * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 - Rambo - uses Analog input 3 + * Note may require analog pins to be defined for different motherboards + **********************************************************************/ +// Uncomment below to enable +//#define FILAMENT_SENSOR + +#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) +#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define MEASURED_UPPER_LIMIT 3.3 //upper limit factor used for sensor reading validation in mm +#define MEASURED_LOWER_LIMIT 1.9 //lower limit factor for sensor reading validation in mm +#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + +//defines used in the code +#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + +//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. +//#define FILAMENT_LCD_DISPLAY + + + + + + +#include "Configuration_adv.h" +#include "thermistortables.h" + +#endif //CONFIGURATION_H From ba9741139ed1b662c8b93bcf7e154d9485db107f Mon Sep 17 00:00:00 2001 From: brupje Date: Tue, 5 May 2015 14:01:52 +0200 Subject: [PATCH 5/8] Clean up pins file for megatronics --- Marlin/pins_MEGATRONICS_3.h | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/Marlin/pins_MEGATRONICS_3.h b/Marlin/pins_MEGATRONICS_3.h index 04a730670d..6b4016bf41 100644 --- a/Marlin/pins_MEGATRONICS_3.h +++ b/Marlin/pins_MEGATRONICS_3.h @@ -26,19 +26,19 @@ #define X_DIR_PIN 57 #define X_ENABLE_PIN 59 #define X_MIN_PIN 37 -#define X_MAX_PIN 40 // 2 // Max endstops default to disabled "-1", set to commented value to enable. +#define X_MAX_PIN 40 // put to -1 to disable -#define Y_STEP_PIN 5 // A6 -#define Y_DIR_PIN 17 // A0 +#define Y_STEP_PIN 5 +#define Y_DIR_PIN 17 #define Y_ENABLE_PIN 4 #define Y_MIN_PIN 41 -#define Y_MAX_PIN 38 // 15 +#define Y_MAX_PIN 38 // put to -1 to disable -#define Z_STEP_PIN 16 // A2 -#define Z_DIR_PIN 11 // A6 -#define Z_ENABLE_PIN 3 // A1 +#define Z_STEP_PIN 16 +#define Z_DIR_PIN 11 +#define Z_ENABLE_PIN 3 #define Z_MIN_PIN 18 -#define Z_MAX_PIN 19 +#define Z_MAX_PIN 19 // put to -1 to disable #define E0_STEP_PIN 28 #define E0_DIR_PIN 27 From 8f8174dc93580b1a3385ea227fefce48cc59174a Mon Sep 17 00:00:00 2001 From: brupje Date: Thu, 7 May 2015 13:12:17 +0200 Subject: [PATCH 6/8] Revert "Default configuration for megatronics." This reverts commit 22e0d2afcb5828b3a62099f786c0cdd45406b4de. --- Marlin/rrw/Configuration_megatronics.h | 817 ------------------------- 1 file changed, 817 deletions(-) delete mode 100644 Marlin/rrw/Configuration_megatronics.h diff --git a/Marlin/rrw/Configuration_megatronics.h b/Marlin/rrw/Configuration_megatronics.h deleted file mode 100644 index c628459891..0000000000 --- a/Marlin/rrw/Configuration_megatronics.h +++ /dev/null @@ -1,817 +0,0 @@ -#ifndef CONFIGURATION_H -#define CONFIGURATION_H - -#include "boards.h" - -//=========================================================================== -//============================= Getting Started ============================= -//=========================================================================== -/* -Here are some standard links for getting your machine calibrated: - * http://reprap.org/wiki/Calibration - * http://youtu.be/wAL9d7FgInk - * http://calculator.josefprusa.cz - * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide - * http://www.thingiverse.com/thing:5573 - * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap - * http://www.thingiverse.com/thing:298812 -*/ - -// This configuration file contains the basic settings. -// Advanced settings can be found in Configuration_adv.h -// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration - -//=========================================================================== -//============================= DELTA Printer =============================== -//=========================================================================== -// For a Delta printer replace the configuration files with the files in the -// example_configurations/delta directory. -// - -//=========================================================================== -//============================= SCARA Printer =============================== -//=========================================================================== -// For a Scara printer replace the configuration files with the files in the -// example_configurations/SCARA directory. -// - -// @section info - -// User-specified version info of this build to display in [Pronterface, etc] terminal window during -// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this -// build by the user have been successfully uploaded into firmware. -#define STRING_VERSION "1.0.3 dev" -#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time -#define STRING_CONFIG_H_AUTHOR "RepRapWorld.com" // Who made the changes. -#define STRING_SPLASH_LINE1 "v" STRING_VERSION // will be shown during bootup in line 1 -//#define STRING_SPLASH_LINE2 STRING_VERSION_CONFIG_H // will be shown during bootup in line2 - -// @section machine - -// SERIAL_PORT selects which serial port should be used for communication with the host. -// This allows the connection of wireless adapters (for instance) to non-default port pins. -// Serial port 0 is still used by the Arduino bootloader regardless of this setting. -// :[0,1,2,3,4,5,6,7] -#define SERIAL_PORT 0 - -// This determines the communication speed of the printer -// :[2400,9600,19200,38400,57600,115200,250000] -#define BAUDRATE 250000 - -// This enables the serial port associated to the Bluetooth interface -//#define BTENABLED // Enable BT interface on AT90USB devices - -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup -#ifndef MOTHERBOARD - #define MOTHERBOARD BOARD_MEGATRONICS_3 -#endif - -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message -// #define CUSTOM_MACHINE_NAME "3D Printer" - -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) -// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000" - -// This defines the number of extruders -// :[1,2,3,4] -#define EXTRUDERS 1 - -// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). -// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). -// For the other hotends it is their distance from the extruder 0 hotend. -//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis -//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis - -//// The following define selects which power supply you have. Please choose the one that matches your setup -// 1 = ATX -// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) -// :{1:'ATX',2:'X-Box 360'} - -#define POWER_SUPPLY 1 - -// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. -// #define PS_DEFAULT_OFF - -// @section temperature - -//=========================================================================== -//============================= Thermal Settings ============================ -//=========================================================================== -// -//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table -// -//// Temperature sensor settings: -// -2 is thermocouple with MAX6675 (only for sensor 0) -// -1 is thermocouple with AD595 -// 0 is not used -// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) -// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) -// 3 is Mendel-parts thermistor (4.7k pullup) -// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! -// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) -// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) -// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) -// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) -// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) -// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) -// 10 is 100k RS thermistor 198-961 (4.7k pullup) -// 11 is 100k beta 3950 1% thermistor (4.7k pullup) -// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) -// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" -// 20 is the PT100 circuit found in the Ultimainboard V2.x -// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 -// -// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k -// (but gives greater accuracy and more stable PID) -// 51 is 100k thermistor - EPCOS (1k pullup) -// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) -// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) -// -// 1047 is Pt1000 with 4k7 pullup -// 1010 is Pt1000 with 1k pullup (non standard) -// 147 is Pt100 with 4k7 pullup -// 110 is Pt100 with 1k pullup (non standard) -// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below. -// Use it for Testing or Development purposes. NEVER for production machine. -// #define DUMMY_THERMISTOR_998_VALUE 25 -// #define DUMMY_THERMISTOR_999_VALUE 100 -// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" } -#define TEMP_SENSOR_0 1 -#define TEMP_SENSOR_1 0 -#define TEMP_SENSOR_2 0 -#define TEMP_SENSOR_3 0 -#define TEMP_SENSOR_BED 1 - -// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted. -//#define TEMP_SENSOR_1_AS_REDUNDANT -#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 - -// Actual temperature must be close to target for this long before M109 returns success -#define TEMP_RESIDENCY_TIME 10 // (seconds) -#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one -#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. - -// The minimal temperature defines the temperature below which the heater will not be enabled It is used -// to check that the wiring to the thermistor is not broken. -// Otherwise this would lead to the heater being powered on all the time. -#define HEATER_0_MINTEMP 5 -#define HEATER_1_MINTEMP 5 -#define HEATER_2_MINTEMP 5 -#define HEATER_3_MINTEMP 5 -#define BED_MINTEMP 5 - -// When temperature exceeds max temp, your heater will be switched off. -// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! -// You should use MINTEMP for thermistor short/failure protection. -#define HEATER_0_MAXTEMP 275 -#define HEATER_1_MAXTEMP 275 -#define HEATER_2_MAXTEMP 275 -#define HEATER_3_MAXTEMP 275 -#define BED_MAXTEMP 150 - -// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the -// average current. The value should be an integer and the heat bed will be turned on for 1 interval of -// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. -//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 - -// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS -//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R -//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R - -//=========================================================================== -//============================= PID Settings ================================ -//=========================================================================== -// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning - -// Comment the following line to disable PID and enable bang-bang. -#define PIDTEMP -#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current -#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current -#ifdef PIDTEMP - //#define PID_DEBUG // Sends debug data to the serial port. - //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX - //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay - //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) - // Set/get with gcode: M301 E[extruder number, 0-2] - #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature - // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. - #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term - #define K1 0.95 //smoothing factor within the PID - #define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine - -// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it -// Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 - -// MakerGear -// #define DEFAULT_Kp 7.0 -// #define DEFAULT_Ki 0.1 -// #define DEFAULT_Kd 12 - -// Mendel Parts V9 on 12V -// #define DEFAULT_Kp 63.0 -// #define DEFAULT_Ki 2.25 -// #define DEFAULT_Kd 440 -#endif // PIDTEMP - -//=========================================================================== -//============================= PID > Bed Temperature Control =============== -//=========================================================================== -// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis -// -// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. -// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz, -// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. -// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. -// If your configuration is significantly different than this and you don't understand the issues involved, you probably -// shouldn't use bed PID until someone else verifies your hardware works. -// If this is enabled, find your own PID constants below. -//#define PIDTEMPBED -// -//#define BED_LIMIT_SWITCHING - -// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. -// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) -// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, -// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) -#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current - -//#define PID_BED_DEBUG // Sends debug data to the serial port. - -#ifdef PIDTEMPBED -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) - #define DEFAULT_bedKp 10.00 - #define DEFAULT_bedKi .023 - #define DEFAULT_bedKd 305.4 - -//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) -//from pidautotune -// #define DEFAULT_bedKp 97.1 -// #define DEFAULT_bedKi 1.41 -// #define DEFAULT_bedKd 1675.16 - -// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. -#endif // PIDTEMPBED - -// @section extruder - -//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit -//can be software-disabled for whatever purposes by -#define PREVENT_DANGEROUS_EXTRUDE -//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately. -#define PREVENT_LENGTHY_EXTRUDE - -#define EXTRUDE_MINTEMP 170 -#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. - -//=========================================================================== -//============================= Thermal Runaway Protection ================== -//=========================================================================== -/* -This is a feature to protect your printer from burn up in flames if it has -a thermistor coming off place (this happened to a friend of mine recently and -motivated me writing this feature). - -The issue: If a thermistor come off, it will read a lower temperature than actual. -The system will turn the heater on forever, burning up the filament and anything -else around. - -After the temperature reaches the target for the first time, this feature will -start measuring for how long the current temperature stays below the target -minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). - -If it stays longer than _PERIOD, it means the thermistor temperature -cannot catch up with the target, so something *may be* wrong. Then, to be on the -safe side, the system will he halt. - -Bear in mind the count down will just start AFTER the first time the -thermistor temperature is over the target, so you will have no problem if -your extruder heater takes 2 minutes to hit the target on heating. - -*/ -// If you want to enable this feature for all your extruder heaters, -// uncomment the 2 defines below: - -// Parameters for all extruder heaters -#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds -#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius - -// If you want to enable this feature for your bed heater, -// uncomment the 2 defines below: - -// Parameters for the bed heater -#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds -#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius - - -//=========================================================================== -//============================= Mechanical Settings ========================= -//=========================================================================== - -// @section machine - -// Uncomment this option to enable CoreXY kinematics -// #define COREXY - -// Enable this option for Toshiba steppers -// #define CONFIG_STEPPERS_TOSHIBA - -// @section homing - -// coarse Endstop Settings -#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors - -#ifndef ENDSTOPPULLUPS - // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined - // #define ENDSTOPPULLUP_XMAX - // #define ENDSTOPPULLUP_YMAX - // #define ENDSTOPPULLUP_ZMAX - // #define ENDSTOPPULLUP_XMIN - // #define ENDSTOPPULLUP_YMIN - // #define ENDSTOPPULLUP_ZMIN - // #define ENDSTOPPULLUP_ZPROBE -#endif - -// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). -const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. -const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. -const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. -const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. -const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. -const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. -const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. -//#define DISABLE_MAX_ENDSTOPS -//#define DISABLE_MIN_ENDSTOPS - -// @section machine -// If you want to enable the Z Probe pin, but disable its use, uncomment the line below. -// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have -// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe, -// this has no effect. -//#define DISABLE_Z_PROBE_ENDSTOP - -// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 -// :{0:'Low',1:'High'} -#define X_ENABLE_ON 0 -#define Y_ENABLE_ON 0 -#define Z_ENABLE_ON 0 -#define E_ENABLE_ON 0 // For all extruders - -// Disables axis when it's not being used. -// WARNING: When motors turn off there is a chance of losing position accuracy! -#define DISABLE_X false -#define DISABLE_Y false -#define DISABLE_Z false - -// @section extruder - -#define DISABLE_E false // For all extruders -#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled - -// @section machine - -// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. -#define INVERT_X_DIR false -#define INVERT_Y_DIR false -#define INVERT_Z_DIR false - -// @section extruder - -// For direct drive extruder v9 set to true, for geared extruder set to false. -#define INVERT_E0_DIR false -#define INVERT_E1_DIR false -#define INVERT_E2_DIR false -#define INVERT_E3_DIR false - -// @section homing - -// ENDSTOP SETTINGS: -// Sets direction of endstops when homing; 1=MAX, -1=MIN -// :[-1,1] -#define X_HOME_DIR -1 -#define Y_HOME_DIR -1 -#define Z_HOME_DIR -1 - -#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. -#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. - -// @section machine - -// Travel limits after homing (units are in mm) -#define X_MIN_POS 0 -#define Y_MIN_POS 0 -#define Z_MIN_POS 0 -#define X_MAX_POS 200 -#define Y_MAX_POS 200 -#define Z_MAX_POS 200 - -//=========================================================================== -//============================= Filament Runout Sensor ====================== -//=========================================================================== -//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament - // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. - // It is assumed that when logic high = filament available - // when logic low = filament ran out -//const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned -//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. - -//=========================================================================== -//============================ Mesh Bed Leveling ============================ -//=========================================================================== - -// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling -// #define MESH_BED_LEVELING // Enable mesh bed leveling - -#ifdef MANUAL_BED_LEVELING - #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis -#endif // MANUAL_BED_LEVELING - -#ifdef MESH_BED_LEVELING - #define MESH_MIN_X 10 - #define MESH_MAX_X (X_MAX_POS - MESH_MIN_X) - #define MESH_MIN_Y 10 - #define MESH_MAX_Y (Y_MAX_POS - MESH_MIN_Y) - #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited - #define MESH_NUM_Y_POINTS 3 - #define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0 -#endif // MESH_BED_LEVELING - -//=========================================================================== -//============================= Bed Auto Leveling =========================== -//=========================================================================== - -// @section bedlevel - -//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) -#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. - -#ifdef ENABLE_AUTO_BED_LEVELING - - // There are 2 different ways to specify probing locations - // - // - "grid" mode - // Probe several points in a rectangular grid. - // You specify the rectangle and the density of sample points. - // This mode is preferred because there are more measurements. - // - // - "3-point" mode - // Probe 3 arbitrary points on the bed (that aren't colinear) - // You specify the XY coordinates of all 3 points. - - // Enable this to sample the bed in a grid (least squares solution) - // Note: this feature generates 10KB extra code size - #define AUTO_BED_LEVELING_GRID - - #ifdef AUTO_BED_LEVELING_GRID - - #define LEFT_PROBE_BED_POSITION 15 - #define RIGHT_PROBE_BED_POSITION 170 - #define FRONT_PROBE_BED_POSITION 20 - #define BACK_PROBE_BED_POSITION 170 - - #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this - - // Set the number of grid points per dimension - // You probably don't need more than 3 (squared=9) - #define AUTO_BED_LEVELING_GRID_POINTS 2 - - #else // !AUTO_BED_LEVELING_GRID - - // Arbitrary points to probe. A simple cross-product - // is used to estimate the plane of the bed. - #define ABL_PROBE_PT_1_X 15 - #define ABL_PROBE_PT_1_Y 180 - #define ABL_PROBE_PT_2_X 15 - #define ABL_PROBE_PT_2_Y 20 - #define ABL_PROBE_PT_3_X 170 - #define ABL_PROBE_PT_3_Y 20 - - #endif // AUTO_BED_LEVELING_GRID - - // Offsets to the probe relative to the extruder tip (Hotend - Probe) - // X and Y offsets must be integers - #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // Probe on: -left +right - #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Probe on: -front +behind - #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!) - - #define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance. - // Be sure you have this distance over your Z_MAX_POS in case - - #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min - - #define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point. - #define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points - #define Z_RAISE_AFTER_PROBING 15 //How much the extruder will be raised after the last probing point. - -// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. - //Useful to retract a deployable probe. - - //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell - //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. - - //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk - //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it. - // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile. - -// #define PROBE_SERVO_DEACTIVATION_DELAY 300 - - -//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, -//it is highly recommended you let this Z_SAFE_HOMING enabled!!! - - #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area. - // When defined, it will: - // - Allow Z homing only after X and Y homing AND stepper drivers still enabled - // - If stepper drivers timeout, it will need X and Y homing again before Z homing - // - Position the probe in a defined XY point before Z Homing when homing all axis (G28) - // - Block Z homing only when the probe is outside bed area. - - #ifdef Z_SAFE_HOMING - - #define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28) - #define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28) - - #endif - - // Support for a dedicated Z PROBE endstop separate from the Z MIN endstop. - // If you would like to use both a Z PROBE and a Z MIN endstop together or just a Z PROBE with a custom pin, uncomment #define Z_PROBE_ENDSTOP and read the instructions below. - // If you want to still use the Z min endstop for homing, disable Z_SAFE_HOMING above. Eg; to park the head outside the bed area when homing with G28. - // WARNING: The Z MIN endstop will need to set properly as it would without a Z PROBE to prevent head crashes and premature stopping during a print. - // To use a separate Z PROBE endstop, you must have a Z_PROBE_PIN defined in the pins.h file for your control board. - // If you are using a servo based Z PROBE, you will need to enable NUM_SERVOS, SERVO_ENDSTOPS and SERVO_ENDSTOPS_ANGLES in the R/C Servo below. - // RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board. Use 5V for powered sensors, otherwise connect to ground and D32 - // for normally closed configuration and 5V and D32 for normally open configurations. Normally closed configuration is advised and assumed. - // The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin. Z_PROBE_PIN is setting the pin to use on the Arduino. Since the D32 pin on the RAMPS maps to D32 on Arduino, this works. - // D32 is currently selected in the RAMPS 1.3/1.4 pin file. All other boards will need changes to the respective pins_XXXXX.h file. - // WARNING: Setting the wrong pin may have unexpected and potentially disastrous outcomes. Use with caution and do your homework. - - //#define Z_PROBE_ENDSTOP - -#endif // ENABLE_AUTO_BED_LEVELING - - -// @section homing - -// The position of the homing switches -//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used -//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) - -// Manual homing switch locations: -// For deltabots this means top and center of the Cartesian print volume. -#ifdef MANUAL_HOME_POSITIONS - #define MANUAL_X_HOME_POS 0 - #define MANUAL_Y_HOME_POS 0 - #define MANUAL_Z_HOME_POS 0 - //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing. -#endif - -// @section movement - -/** - * MOVEMENT SETTINGS - */ - -#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) - -// default settings - -#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402*2,78.7402*2,5120.00,760*1*1.5} // default steps per unit for Ultimaker -#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) -#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. - -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves - -// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) -#define DEFAULT_XYJERK 20.0 // (mm/sec) -#define DEFAULT_ZJERK 0.4 // (mm/sec) -#define DEFAULT_EJERK 5.0 // (mm/sec) - - -//============================================================================= -//============================= Additional Features =========================== -//============================================================================= - -// @section more - -// Custom M code points -#define CUSTOM_M_CODES -#ifdef CUSTOM_M_CODES - #ifdef ENABLE_AUTO_BED_LEVELING - #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851 - #define Z_PROBE_OFFSET_RANGE_MIN -20 - #define Z_PROBE_OFFSET_RANGE_MAX 20 - #endif -#endif - -// @section extras - -// EEPROM -// The microcontroller can store settings in the EEPROM, e.g. max velocity... -// M500 - stores parameters in EEPROM -// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). -// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. -//define this to enable EEPROM support -//#define EEPROM_SETTINGS - -#ifdef EEPROM_SETTINGS - // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: - #define EEPROM_CHITCHAT // please keep turned on if you can. -#endif - - -// @section temperature - -// Preheat Constants -#define PLA_PREHEAT_HOTEND_TEMP 180 -#define PLA_PREHEAT_HPB_TEMP 70 -#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 - -#define ABS_PREHEAT_HOTEND_TEMP 240 -#define ABS_PREHEAT_HPB_TEMP 110 -#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 - -//==============================LCD and SD support============================= -// @section lcd - -// Define your display language below. Replace (en) with your language code and uncomment. -// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test -// See also language.h -#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) - -// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display. -// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset. -// See also documentation/LCDLanguageFont.md - #define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware - //#define DISPLAY_CHARSET_HD44780_WESTERN - //#define DISPLAY_CHARSET_HD44780_CYRILLIC - -#define ULTRA_LCD //general LCD support, also 16x2 -//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) -#define SDSUPPORT // Enable SD Card Support in Hardware Console -//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) -#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication -//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder -//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking -//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. -//#define ULTIPANEL //the UltiPanel as on Thingiverse -//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click -//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click - // 0 to disable buzzer feedback. Test with M300 S P -// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) -// http://reprap.org/wiki/PanelOne -//#define PANEL_ONE - -// The MaKr3d Makr-Panel with graphic controller and SD support -// http://reprap.org/wiki/MaKr3d_MaKrPanel -//#define MAKRPANEL - -// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD -// http://panucatt.com -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib -//#define VIKI2 -//#define miniVIKI - -// The RepRapDiscount Smart Controller (white PCB) -// http://reprap.org/wiki/RepRapDiscount_Smart_Controller -//#define REPRAP_DISCOUNT_SMART_CONTROLLER - -// The GADGETS3D G3D LCD/SD Controller (blue PCB) -// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel -//#define G3D_PANEL - -// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB) -// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller -// -// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib -//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER - -// The RepRapWorld REPRAPWORLD_KEYPAD v1.1 -// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 -#define REPRAPWORLD_KEYPAD -#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click - -// The Elefu RA Board Control Panel -// http://www.elefu.com/index.php?route=product/product&product_id=53 -// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C -//#define RA_CONTROL_PANEL - -/** - * I2C Panels - */ - -//#define LCD_I2C_SAINSMART_YWROBOT - -// PANELOLU2 LCD with status LEDs, separate encoder and click inputs -//#define LCD_I2C_PANELOLU2 - -// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs -//#define LCD_I2C_VIKI - -// Shift register panels -// --------------------- -// 2 wire Non-latching LCD SR from: -// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection - -//#define SAV_3DLCD - -// @section extras - -// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino -//#define FAST_PWM_FAN - -// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency -// which is not as annoying as with the hardware PWM. On the other hand, if this frequency -// is too low, you should also increment SOFT_PWM_SCALE. -//#define FAN_SOFT_PWM - -// Incrementing this by 1 will double the software PWM frequency, -// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. -// However, control resolution will be halved for each increment; -// at zero value, there are 128 effective control positions. -#define SOFT_PWM_SCALE 0 - -// Temperature status LEDs that display the hotend and bet temperature. -// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on. -// Otherwise the RED led is on. There is 1C hysteresis. -//#define TEMP_STAT_LEDS - -// M240 Triggers a camera by emulating a Canon RC-1 Remote -// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ -// #define PHOTOGRAPH_PIN 23 - -// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure -//#define SF_ARC_FIX - -// Support for the BariCUDA Paste Extruder. -//#define BARICUDA - -//define BlinkM/CyzRgb Support -//#define BLINKM - -/*********************************************************************\ -* R/C SERVO support -* Sponsored by TrinityLabs, Reworked by codexmas -**********************************************************************/ - -// Number of servos -// -// If you select a configuration below, this will receive a default value and does not need to be set manually -// set it manually if you have more servos than extruders and wish to manually control some -// leaving it undefined or defining as 0 will disable the servo subsystem -// If unsure, leave commented / disabled -// -//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command - -// Servo Endstops -// -// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. -// Use M851 to set the z-probe vertical offset from the nozzle. Store that setting with M500. -// -//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1 -//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles - -/**********************************************************************\ - * Support for a filament diameter sensor - * Also allows adjustment of diameter at print time (vs at slicing) - * Single extruder only at this point (extruder 0) - * - * Motherboards - * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector - * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) - * 301 - Rambo - uses Analog input 3 - * Note may require analog pins to be defined for different motherboards - **********************************************************************/ -// Uncomment below to enable -//#define FILAMENT_SENSOR - -#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) -#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel - -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation -#define MEASURED_UPPER_LIMIT 3.3 //upper limit factor used for sensor reading validation in mm -#define MEASURED_LOWER_LIMIT 1.9 //lower limit factor for sensor reading validation in mm -#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) - -//defines used in the code -#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially - -//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. -//#define FILAMENT_LCD_DISPLAY - - - - - - -#include "Configuration_adv.h" -#include "thermistortables.h" - -#endif //CONFIGURATION_H From b7fcb1158044609d9f46ac00e8bc3f10f66bc833 Mon Sep 17 00:00:00 2001 From: brupje Date: Thu, 7 May 2015 13:18:05 +0200 Subject: [PATCH 7/8] Added example configuration for Megatronics --- .../Megatronics/Configuration_megatronics.h | 817 ++++++++++++++++++ 1 file changed, 817 insertions(+) create mode 100644 Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h new file mode 100644 index 0000000000..c628459891 --- /dev/null +++ b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h @@ -0,0 +1,817 @@ +#ifndef CONFIGURATION_H +#define CONFIGURATION_H + +#include "boards.h" + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== +/* +Here are some standard links for getting your machine calibrated: + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 +*/ + +// This configuration file contains the basic settings. +// Advanced settings can be found in Configuration_adv.h +// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer replace the configuration files with the files in the +// example_configurations/delta directory. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a Scara printer replace the configuration files with the files in the +// example_configurations/SCARA directory. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_VERSION "1.0.3 dev" +#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time +#define STRING_CONFIG_H_AUTHOR "RepRapWorld.com" // Who made the changes. +#define STRING_SPLASH_LINE1 "v" STRING_VERSION // will be shown during bootup in line 1 +//#define STRING_SPLASH_LINE2 STRING_VERSION_CONFIG_H // will be shown during bootup in line2 + +// @section machine + +// SERIAL_PORT selects which serial port should be used for communication with the host. +// This allows the connection of wireless adapters (for instance) to non-default port pins. +// Serial port 0 is still used by the Arduino bootloader regardless of this setting. +// :[0,1,2,3,4,5,6,7] +#define SERIAL_PORT 0 + +// This determines the communication speed of the printer +// :[2400,9600,19200,38400,57600,115200,250000] +#define BAUDRATE 250000 + +// This enables the serial port associated to the Bluetooth interface +//#define BTENABLED // Enable BT interface on AT90USB devices + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_MEGATRONICS_3 +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +// #define CUSTOM_MACHINE_NAME "3D Printer" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// This defines the number of extruders +// :[1,2,3,4] +#define EXTRUDERS 1 + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + +//// The following define selects which power supply you have. Please choose the one that matches your setup +// 1 = ATX +// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) +// :{1:'ATX',2:'X-Box 360'} + +#define POWER_SUPPLY 1 + +// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. +// #define PS_DEFAULT_OFF + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== +// +//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table +// +//// Temperature sensor settings: +// -2 is thermocouple with MAX6675 (only for sensor 0) +// -1 is thermocouple with AD595 +// 0 is not used +// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup) +// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) +// 3 is Mendel-parts thermistor (4.7k pullup) +// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! +// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) +// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) +// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) +// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) +// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) +// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) +// 10 is 100k RS thermistor 198-961 (4.7k pullup) +// 11 is 100k beta 3950 1% thermistor (4.7k pullup) +// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) +// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" +// 20 is the PT100 circuit found in the Ultimainboard V2.x +// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 +// +// 1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k +// (but gives greater accuracy and more stable PID) +// 51 is 100k thermistor - EPCOS (1k pullup) +// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup) +// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) +// +// 1047 is Pt1000 with 4k7 pullup +// 1010 is Pt1000 with 1k pullup (non standard) +// 147 is Pt100 with 4k7 pullup +// 110 is Pt100 with 1k pullup (non standard) +// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below. +// Use it for Testing or Development purposes. NEVER for production machine. +// #define DUMMY_THERMISTOR_998_VALUE 25 +// #define DUMMY_THERMISTOR_999_VALUE 100 +// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" } +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_BED 1 + +// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +// Actual temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define BED_MAXTEMP 150 + +// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the +// average current. The value should be an integer and the heat bed will be turned on for 1 interval of +// HEATER_BED_DUTY_CYCLE_DIVIDER intervals. +//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4 + +// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS +//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R +//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#ifdef PIDTEMP + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + #define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term + #define K1 0.95 //smoothing factor within the PID + #define PID_dT ((16.0 * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine + +// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it +// Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + +// MakerGear +// #define DEFAULT_Kp 7.0 +// #define DEFAULT_Ki 0.1 +// #define DEFAULT_Kd 12 + +// Mendel Parts V9 on 12V +// #define DEFAULT_Kp 63.0 +// #define DEFAULT_Ki 2.25 +// #define DEFAULT_Kd 440 +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +//#define PIDTEMPBED +// +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +//#define PID_BED_DEBUG // Sends debug data to the serial port. + +#ifdef PIDTEMPBED +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + +//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) +//from pidautotune +// #define DEFAULT_bedKp 97.1 +// #define DEFAULT_bedKi 1.41 +// #define DEFAULT_bedKd 1675.16 + +// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit +//can be software-disabled for whatever purposes by +#define PREVENT_DANGEROUS_EXTRUDE +//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately. +#define PREVENT_LENGTHY_EXTRUDE + +#define EXTRUDE_MINTEMP 170 +#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances. + +//=========================================================================== +//============================= Thermal Runaway Protection ================== +//=========================================================================== +/* +This is a feature to protect your printer from burn up in flames if it has +a thermistor coming off place (this happened to a friend of mine recently and +motivated me writing this feature). + +The issue: If a thermistor come off, it will read a lower temperature than actual. +The system will turn the heater on forever, burning up the filament and anything +else around. + +After the temperature reaches the target for the first time, this feature will +start measuring for how long the current temperature stays below the target +minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS). + +If it stays longer than _PERIOD, it means the thermistor temperature +cannot catch up with the target, so something *may be* wrong. Then, to be on the +safe side, the system will he halt. + +Bear in mind the count down will just start AFTER the first time the +thermistor temperature is over the target, so you will have no problem if +your extruder heater takes 2 minutes to hit the target on heating. + +*/ +// If you want to enable this feature for all your extruder heaters, +// uncomment the 2 defines below: + +// Parameters for all extruder heaters +#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds +#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius + +// If you want to enable this feature for your bed heater, +// uncomment the 2 defines below: + +// Parameters for the bed heater +#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds +#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius + + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment this option to enable CoreXY kinematics +// #define COREXY + +// Enable this option for Toshiba steppers +// #define CONFIG_STEPPERS_TOSHIBA + +// @section homing + +// coarse Endstop Settings +#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors + +#ifndef ENDSTOPPULLUPS + // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined + // #define ENDSTOPPULLUP_XMAX + // #define ENDSTOPPULLUP_YMAX + // #define ENDSTOPPULLUP_ZMAX + // #define ENDSTOPPULLUP_XMIN + // #define ENDSTOPPULLUP_YMIN + // #define ENDSTOPPULLUP_ZMIN + // #define ENDSTOPPULLUP_ZPROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. +const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop. +//#define DISABLE_MAX_ENDSTOPS +//#define DISABLE_MIN_ENDSTOPS + +// @section machine +// If you want to enable the Z Probe pin, but disable its use, uncomment the line below. +// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have +// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe, +// this has no effect. +//#define DISABLE_Z_PROBE_ENDSTOP + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{0:'Low',1:'High'} +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR false +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false + +// @section homing + +// ENDSTOP SETTINGS: +// Sets direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS. +#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. + +// @section machine + +// Travel limits after homing (units are in mm) +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS 200 +#define Y_MAX_POS 200 +#define Z_MAX_POS 200 + +//=========================================================================== +//============================= Filament Runout Sensor ====================== +//=========================================================================== +//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament + // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made. + // It is assumed that when logic high = filament available + // when logic low = filament ran out +//const bool FIL_RUNOUT_INVERTING = true; // Should be uncommented and true or false should assigned +//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. + +//=========================================================================== +//============================ Mesh Bed Leveling ============================ +//=========================================================================== + +// #define MANUAL_BED_LEVELING // Add display menu option for bed leveling +// #define MESH_BED_LEVELING // Enable mesh bed leveling + +#ifdef MANUAL_BED_LEVELING + #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis +#endif // MANUAL_BED_LEVELING + +#ifdef MESH_BED_LEVELING + #define MESH_MIN_X 10 + #define MESH_MAX_X (X_MAX_POS - MESH_MIN_X) + #define MESH_MIN_Y 10 + #define MESH_MAX_Y (Y_MAX_POS - MESH_MIN_Y) + #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited + #define MESH_NUM_Y_POINTS 3 + #define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0 +#endif // MESH_BED_LEVELING + +//=========================================================================== +//============================= Bed Auto Leveling =========================== +//=========================================================================== + +// @section bedlevel + +//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line) +#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled. + +#ifdef ENABLE_AUTO_BED_LEVELING + + // There are 2 different ways to specify probing locations + // + // - "grid" mode + // Probe several points in a rectangular grid. + // You specify the rectangle and the density of sample points. + // This mode is preferred because there are more measurements. + // + // - "3-point" mode + // Probe 3 arbitrary points on the bed (that aren't colinear) + // You specify the XY coordinates of all 3 points. + + // Enable this to sample the bed in a grid (least squares solution) + // Note: this feature generates 10KB extra code size + #define AUTO_BED_LEVELING_GRID + + #ifdef AUTO_BED_LEVELING_GRID + + #define LEFT_PROBE_BED_POSITION 15 + #define RIGHT_PROBE_BED_POSITION 170 + #define FRONT_PROBE_BED_POSITION 20 + #define BACK_PROBE_BED_POSITION 170 + + #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this + + // Set the number of grid points per dimension + // You probably don't need more than 3 (squared=9) + #define AUTO_BED_LEVELING_GRID_POINTS 2 + + #else // !AUTO_BED_LEVELING_GRID + + // Arbitrary points to probe. A simple cross-product + // is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 + + #endif // AUTO_BED_LEVELING_GRID + + // Offsets to the probe relative to the extruder tip (Hotend - Probe) + // X and Y offsets must be integers + #define X_PROBE_OFFSET_FROM_EXTRUDER -25 // Probe on: -left +right + #define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Probe on: -front +behind + #define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!) + + #define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance. + // Be sure you have this distance over your Z_MAX_POS in case + + #define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min + + #define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point. + #define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points + #define Z_RAISE_AFTER_PROBING 15 //How much the extruder will be raised after the last probing point. + +// #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. + //Useful to retract a deployable probe. + + //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell + //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + + //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk + //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it. + // You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile. + +// #define PROBE_SERVO_DEACTIVATION_DELAY 300 + + +//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing, +//it is highly recommended you let this Z_SAFE_HOMING enabled!!! + + #define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area. + // When defined, it will: + // - Allow Z homing only after X and Y homing AND stepper drivers still enabled + // - If stepper drivers timeout, it will need X and Y homing again before Z homing + // - Position the probe in a defined XY point before Z Homing when homing all axis (G28) + // - Block Z homing only when the probe is outside bed area. + + #ifdef Z_SAFE_HOMING + + #define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28) + #define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28) + + #endif + + // Support for a dedicated Z PROBE endstop separate from the Z MIN endstop. + // If you would like to use both a Z PROBE and a Z MIN endstop together or just a Z PROBE with a custom pin, uncomment #define Z_PROBE_ENDSTOP and read the instructions below. + // If you want to still use the Z min endstop for homing, disable Z_SAFE_HOMING above. Eg; to park the head outside the bed area when homing with G28. + // WARNING: The Z MIN endstop will need to set properly as it would without a Z PROBE to prevent head crashes and premature stopping during a print. + // To use a separate Z PROBE endstop, you must have a Z_PROBE_PIN defined in the pins.h file for your control board. + // If you are using a servo based Z PROBE, you will need to enable NUM_SERVOS, SERVO_ENDSTOPS and SERVO_ENDSTOPS_ANGLES in the R/C Servo below. + // RAMPS 1.3/1.4 boards may be able to use the 5V, Ground and the D32 pin in the Aux 4 section of the RAMPS board. Use 5V for powered sensors, otherwise connect to ground and D32 + // for normally closed configuration and 5V and D32 for normally open configurations. Normally closed configuration is advised and assumed. + // The D32 pin in Aux 4 on RAMPS maps to the Arduino D32 pin. Z_PROBE_PIN is setting the pin to use on the Arduino. Since the D32 pin on the RAMPS maps to D32 on Arduino, this works. + // D32 is currently selected in the RAMPS 1.3/1.4 pin file. All other boards will need changes to the respective pins_XXXXX.h file. + // WARNING: Setting the wrong pin may have unexpected and potentially disastrous outcomes. Use with caution and do your homework. + + //#define Z_PROBE_ENDSTOP + +#endif // ENABLE_AUTO_BED_LEVELING + + +// @section homing + +// The position of the homing switches +//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used +//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0) + +// Manual homing switch locations: +// For deltabots this means top and center of the Cartesian print volume. +#ifdef MANUAL_HOME_POSITIONS + #define MANUAL_X_HOME_POS 0 + #define MANUAL_Y_HOME_POS 0 + #define MANUAL_Z_HOME_POS 0 + //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing. +#endif + +// @section movement + +/** + * MOVEMENT SETTINGS + */ + +#define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) + +// default settings + +#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402*2,78.7402*2,5120.00,760*1*1.5} // default steps per unit for Ultimaker +#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) +#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. + +#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves + +// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) +#define DEFAULT_XYJERK 20.0 // (mm/sec) +#define DEFAULT_ZJERK 0.4 // (mm/sec) +#define DEFAULT_EJERK 5.0 // (mm/sec) + + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section more + +// Custom M code points +#define CUSTOM_M_CODES +#ifdef CUSTOM_M_CODES + #ifdef ENABLE_AUTO_BED_LEVELING + #define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851 + #define Z_PROBE_OFFSET_RANGE_MIN -20 + #define Z_PROBE_OFFSET_RANGE_MAX 20 + #endif +#endif + +// @section extras + +// EEPROM +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +//define this to enable EEPROM support +//#define EEPROM_SETTINGS + +#ifdef EEPROM_SETTINGS + // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out: + #define EEPROM_CHITCHAT // please keep turned on if you can. +#endif + + +// @section temperature + +// Preheat Constants +#define PLA_PREHEAT_HOTEND_TEMP 180 +#define PLA_PREHEAT_HPB_TEMP 70 +#define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 + +#define ABS_PREHEAT_HOTEND_TEMP 240 +#define ABS_PREHEAT_HPB_TEMP 110 +#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255 + +//==============================LCD and SD support============================= +// @section lcd + +// Define your display language below. Replace (en) with your language code and uncomment. +// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu, kana, kana_utf8, cn, test +// See also language.h +#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en) + +// Choose ONE of these 3 charsets. This has to match your hardware. Ignored for full graphic display. +// To find out what type you have - compile with (test) - upload - click to get the menu. You'll see two typical lines from the upper half of the charset. +// See also documentation/LCDLanguageFont.md + #define DISPLAY_CHARSET_HD44780_JAPAN // this is the most common hardware + //#define DISPLAY_CHARSET_HD44780_WESTERN + //#define DISPLAY_CHARSET_HD44780_CYRILLIC + +#define ULTRA_LCD //general LCD support, also 16x2 +//#define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) +#define SDSUPPORT // Enable SD Card Support in Hardware Console +//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error) +#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication +//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder +//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking +//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. +//#define ULTIPANEL //the UltiPanel as on Thingiverse +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click + // 0 to disable buzzer feedback. Test with M300 S P +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +//#define PANEL_ONE + +// The MaKr3d Makr-Panel with graphic controller and SD support +// http://reprap.org/wiki/MaKr3d_MaKrPanel +//#define MAKRPANEL + +// The Panucatt Devices Viki 2.0 and mini Viki with Graphic LCD +// http://panucatt.com +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +//#define VIKI2 +//#define miniVIKI + +// The RepRapDiscount Smart Controller (white PCB) +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// The GADGETS3D G3D LCD/SD Controller (blue PCB) +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +//#define G3D_PANEL + +// The RepRapDiscount FULL GRAPHIC Smart Controller (quadratic white PCB) +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// The RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +#define REPRAPWORLD_KEYPAD +#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 // how much should be moved when a key is pressed, eg 10.0 means 10mm per click + +// The Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C +//#define RA_CONTROL_PANEL + +/** + * I2C Panels + */ + +//#define LCD_I2C_SAINSMART_YWROBOT + +// PANELOLU2 LCD with status LEDs, separate encoder and click inputs +//#define LCD_I2C_PANELOLU2 + +// Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs +//#define LCD_I2C_VIKI + +// Shift register panels +// --------------------- +// 2 wire Non-latching LCD SR from: +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection + +//#define SAV_3DLCD + +// @section extras + +// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// Temperature status LEDs that display the hotend and bet temperature. +// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on. +// Otherwise the RED led is on. There is 1C hysteresis. +//#define TEMP_STAT_LEDS + +// M240 Triggers a camera by emulating a Canon RC-1 Remote +// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +// #define PHOTOGRAPH_PIN 23 + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder. +//#define BARICUDA + +//define BlinkM/CyzRgb Support +//#define BLINKM + +/*********************************************************************\ +* R/C SERVO support +* Sponsored by TrinityLabs, Reworked by codexmas +**********************************************************************/ + +// Number of servos +// +// If you select a configuration below, this will receive a default value and does not need to be set manually +// set it manually if you have more servos than extruders and wish to manually control some +// leaving it undefined or defining as 0 will disable the servo subsystem +// If unsure, leave commented / disabled +// +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Servo Endstops +// +// This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes. +// Use M851 to set the z-probe vertical offset from the nozzle. Store that setting with M500. +// +//#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1 +//#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles + +/**********************************************************************\ + * Support for a filament diameter sensor + * Also allows adjustment of diameter at print time (vs at slicing) + * Single extruder only at this point (extruder 0) + * + * Motherboards + * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector + * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 - Rambo - uses Analog input 3 + * Note may require analog pins to be defined for different motherboards + **********************************************************************/ +// Uncomment below to enable +//#define FILAMENT_SENSOR + +#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2) +#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel + +#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation +#define MEASURED_UPPER_LIMIT 3.3 //upper limit factor used for sensor reading validation in mm +#define MEASURED_LOWER_LIMIT 1.9 //lower limit factor for sensor reading validation in mm +#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM) + +//defines used in the code +#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially + +//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status. Status will appear for 5 sec. +//#define FILAMENT_LCD_DISPLAY + + + + + + +#include "Configuration_adv.h" +#include "thermistortables.h" + +#endif //CONFIGURATION_H From d1148a0198b9af9947b83c987731bb1a70e51d7b Mon Sep 17 00:00:00 2001 From: brupje Date: Fri, 8 May 2015 14:36:23 +0200 Subject: [PATCH 8/8] Rename Configuration_megatronics.h to Configuration.h --- .../Megatronics/{Configuration_megatronics.h => Configuration.h} | 0 1 file changed, 0 insertions(+), 0 deletions(-) rename Marlin/example_configurations/RepRapWorld/Megatronics/{Configuration_megatronics.h => Configuration.h} (100%) diff --git a/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h b/Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h similarity index 100% rename from Marlin/example_configurations/RepRapWorld/Megatronics/Configuration_megatronics.h rename to Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h