Move 'pins' files

2017-09-06 06:28:31 -05:00
parent 2b3b7d5d7f
commit 0b9a88d6ce
79 changed files with 0 additions and 0 deletions
--- a/Marlin/src/pins/pins_MKS_13.h
+++ b/Marlin/src/pins/pins_MKS_13.h
@ -0,0 +1,144 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Arduino Mega with RAMPS v1.4 adjusted pin assignments
+ *
+ *  MKS v1.3  (Extruder, Fan, Bed)
+ *  MKS v1.3  (Extruder, Extruder, Fan, Bed)
+ *  MKS v1.4  (Extruder, Fan, Bed)
+ *  MKS v1.4  (Extruder, Extruder, Fan, Bed)
+ */
+
+#if HOTENDS > 2 || E_STEPPERS > 2
+  #error "MKS 1.3/1.4 supports up to 2 hotends / E-steppers. Comment out this line to continue."
+#endif
+
+#define BOARD_NAME "MKS > v1.3"
+
+//
+// Heaters / Fans
+//
+// Power outputs EFBF or EFBE
+#define MOSFET_D_PIN 7
+
+//
+// PSU / SERVO
+//
+// If POWER_SUPPLY is specified, always hijack Servo 3
+//
+#if POWER_SUPPLY > 0
+  #define SERVO3_PIN      -1
+  #define PS_ON_PIN        4
+#endif
+
+#include "pins_RAMPS.h"
+
+//
+// LCD / Controller
+//
+#if ENABLED(VIKI2) || ENABLED(miniVIKI)
+  /**
+   * VIKI2 Has two groups of wires with...
+   *
+   * +Vin     + Input supply, requires 120ma for LCD and mSD card
+   * GND      Ground Pin
+   * MOSI     Data input for LCD and SD
+   * MISO     Data output for SD
+   * SCK      Clock for LCD and SD
+   * AO       Reg. Sel for LCD
+   * LCS      Chip Select for LCD
+   * SDCS     Chip Select for SD
+   * SDCD     Card Detect pin for SD
+   * ENCA     Encoder output A
+   * ENCB     Encoder output B
+   * ENCBTN   Encoder button switch
+   *
+   * BTN      Panel mounted button switch
+   * BUZZER   Piezo buzzer
+   * BLUE-LED Blue LED ring pin (3 to 5v, mosfet buffered)
+   * RED-LED  Red LED ring pin (3 to 5v, mosfet buffered)
+   *
+   * This configuration uses the following arrangement:
+   *
+   * EXP1 D37 = EN2   D35 = EN1     EXP2 D50 = MISO  D52 = SCK
+   *      D17 = BLUE  D16 = RED          D31 = ENC   D53 = SDCS
+   *      D23 = KILL  D25 = BUZZ         D33 = ---   D51 = MOSI
+   *      D27 = A0    D29 = LCS          D49 = SDCD  RST = ---
+   *      GND = GND   5V  = 5V           GND = ---   D41 = ---
+   */
+
+  #undef BTN_EN1
+  #undef BTN_EN2
+  #undef BTN_ENC
+  #undef DOGLCD_A0
+  #undef DOGLCD_CS
+  #undef SD_DETECT_PIN
+  #undef BEEPER_PIN
+  #undef KILL_PIN
+
+  //
+  // VIKI2 12-wire lead
+  //
+
+  // orange/white         SDCD
+  #define SD_DETECT_PIN   49
+
+  // white                ENCA
+  #define BTN_EN1         35
+
+  // green                ENCB
+  #define BTN_EN2         37
+
+  // purple               ENCBTN
+  #define BTN_ENC         31
+
+  // brown                A0
+  #define DOGLCD_A0       27
+
+  // green/white          LCS
+  #define DOGLCD_CS       29
+
+                       // 50    gray   MISO
+                       // 51    yellow MOSI
+                       // 52    orange SCK
+
+  // blue                 SDCS
+  //#define SDSS            53
+
+  //
+  // VIKI2 4-wire lead
+  //
+
+  // blue                 BTN
+  #define KILL_PIN        23
+
+  // green                BUZZER
+  #define BEEPER_PIN      25
+
+  // yellow               RED-LED
+  #define STAT_LED_RED_PIN 16
+
+  // white                BLUE-LED
+  #define STAT_LED_BLUE_PIN 17
+
+#endif